Yamaha CL5/CL3/CL1 V1.5 Användarmanual

Kategori
Programvara
Typ
Användarmanual

Denna manual är också lämplig för

EN
How to Use This Reference Manual
The CL5/CL3/CL1 Reference Manual (this document) allows you to
search for terms and take advantage of links in the text.
Searching for terms
To search for a term, use the search function of the software youre using
to view this document.
If youre using Adobe Reader, enter the term in the search box and press
the <Enter> key of your computer keyboard to search for occurrences of
that term.
Displaying the next/previous view
If you’re using Adobe Reader, you can jump to the previous/next view in
your viewing history. This is a convenient way to jump back to the
previous page after you’ve used a link to jump to a different page.
Using the Function Tree
A function tree for the CL5/CL3/CL1 is provided on page 4 and
following. You can use this function tree to find the page that explains
an on-screen display or function.
Reference Manual
Contents
Reference Manual
2
Contents
How to Use This Reference Manual .......................................................................... 1
Function Tree ............................................................................ 4
SELECTED CHANNEL section ...................................................... 6
About the SELECTED CHANNEL section................................................................... 6
Operations in the SELECTED CHANNEL section ....................................................... 6
SELECTED CHANNEL VIEW screen ........................................................................... 7
Centralogic section ................................................................. 11
About the Centralogic section................................................................................ 11
Operations in the Centralogic section .................................................................... 11
OVERVIEW screen .................................................................................................. 12
Input and output patching..................................................... 15
CL console internal patching and Dante audio network patching .......................... 15
Changing the output patch settings ...................................................................... 16
Changing the input patch settings......................................................................... 19
Inserting an external device into a channel ............................................................ 21
Directly outputting an INPUT channel ................................................................... 23
Recording or playing back using DAW on a computer ........................................... 25
Input channels ........................................................................ 27
Signal flow for input channels................................................................................ 27
Specifying the channel name, icon and channel color............................................ 28
Making HA (Head Amp) settings............................................................................ 30
Sending a signal from an input channel to the STEREO/MONO buses ................... 35
Sending a signal from an input channel to a MIX/MATRIX bus .............................. 39
Correcting delay between channels (Input Delay).................................................. 44
Channel library operations..................................................................................... 45
Output channels ..................................................................... 46
Signal flow for output channels ............................................................................. 46
Specifying the channel name, icon and channel color............................................ 47
Sending signals from MIX channels to the STEREO/MONO bus ............................. 48
Sending signals from MIX channels and STEREO/MONO channels to
MATRIX buses............................................................................................. 51
Correcting delay between channels (Output Delay)............................................... 55
Channel library operations..................................................................................... 55
EQ and Dynamics ..................................................................... 56
About EQ and dynamics ......................................................................................... 56
Using EQ ................................................................................................................ 56
Using dynamics ...................................................................................................... 59
Using the EQ or Dynamics libraries ......................................................................... 63
Grouping and linking .............................................................. 64
About DCA groups and Mute groups ..................................................................... 64
Using DCA groups.................................................................................................. 64
Using mute groups................................................................................................. 66
Channel Link function ............................................................................................ 70
Copying, moving, or initializing a channel.............................................................. 73
Scene memory ......................................................................... 77
About scene memories ........................................................................................... 77
Using scene memories............................................................................................ 77
Editing scene memories.......................................................................................... 82
Using the Global Paste function.............................................................................. 85
Using the Focus function ........................................................................................ 87
Using the Recall Safe function................................................................................. 88
Using the Fade function.......................................................................................... 91
Outputting a control signal to an external device in tandem with scene recall
(GPI OUT) ................................................................................................... 93
Playing back an audio file that links to a scene recall............................................... 94
Using Preview mode............................................................................................... 96
Monitor and Cue functions ..................................................... 97
About the Monitor and Cue functions .................................................................... 97
Using the Monitor function .................................................................................... 98
Using the Cue function......................................................................................... 101
Operating the Cue function.................................................................................. 102
Talkback and Oscillator......................................................... 106
About the Talkback and Oscillator functions ......................................................... 106
Using Talkback ..................................................................................................... 106
Using the Oscillator function ................................................................................ 108
Meters.................................................................................... 111
Operations in the METER screen ........................................................................... 111
Using an MBCL meter bridge (optional) on the CL3 or CL1 console ..................... 113
Contents
Reference Manual
3
Graphic EQ, effects, and Premium Rack ............................... 114
About the virtual rack .......................................................................................... 114
Virtual rack operations ......................................................................................... 115
Graphic EQ operations......................................................................................... 118
About the internal effects..................................................................................... 122
Using the Premium Rack...................................................................................... 130
Using the graphic EQ, effect, and Premium Rack libraries..................................... 137
I/O device and external head amp ....................................... 138
Using an I/O device ............................................................................................. 138
I/O device patching ............................................................................................. 138
Remotely controlling an Rio unit.......................................................................... 140
Remotely controlling an amp............................................................................... 143
Using an external head amp ................................................................................ 144
MIDI....................................................................................... 149
MIDI functionality on the CL series console.......................................................... 149
Basic MIDI settings .............................................................................................. 149
Using Program Changes to recall scenes and library items ................................... 152
Using Control Changes to control parameters ..................................................... 155
Using Parameter Changes to control parameters ................................................. 157
User settings (Security) ........................................................ 158
User Level settings ............................................................................................... 158
Preferences .......................................................................................................... 168
USER DEFINED keys ............................................................................................. 169
USER DEFINED knobs........................................................................................... 171
Assignable encoders ............................................................................................ 172
Custom fader bank .............................................................................................. 173
Master fader ........................................................................................................ 174
Console Lock ....................................................................................................... 175
Saving and loading setup data to and from a USB flash drive............................... 177
Formatting a USB flash drive................................................................................ 180
Recorder................................................................................ 181
About the USB memory recorder ......................................................................... 181
Assigning channels to the input and output of the recorder................................. 181
Recording audio to a USB flash drive.................................................................... 183
Playing back audio files from a USB flash drive ..................................................... 185
Editing the title list............................................................................................... 187
Using the CL console with Nuendo Live............................................................... 188
Help function ........................................................................ 193
Loading a Help file from a USB flash drive............................................................ 193
Loading a text file from a USB flash drive.............................................................. 193
Viewing Help........................................................................................................ 194
Using USER DEFINED keys to recall Help directly................................................... 194
Other functions ..................................................................... 196
About the SETUP screen ....................................................................................... 196
Word clock and slot settings................................................................................. 198
Using cascade connections ................................................................................... 200
Basic settings for MIX buses and MATRIX buses.................................................... 202
Switching the entire phantom power supply on/off.............................................. 203
Specifying the brightness of the touch screen, LEDs, channel name displays,
and lamps ................................................................................................. 204
Setting the date and time of the internal clock ..................................................... 204
Setting the network address ................................................................................. 205
Initializing the unit to factory default settings ....................................................... 206
Adjusting the detection point of the touch screen (Calibration function) .............. 207
Adjusting the faders (Calibration function) ........................................................... 208
Fine-tuning the input and output gain (Calibration function) ............................... 209
Adjusting the channel color (Calibration function)................................................ 211
Adjusting the brightness of the channel name display .......................................... 212
Adjusting the contrast of the channel name display.............................................. 213
Dante audio network settings ............................................................................... 213
Using GPI (General Purpose Interface) .................................................................. 221
Appendices ............................................................................ 227
EQ Library List ...................................................................................................... 227
DYNAMICS Library List ......................................................................................... 228
Dynamics Parameters ........................................................................................... 230
Effect Type List ..................................................................................................... 232
Effects Parameters................................................................................................. 233
Premium Rack Processor Parameters ..................................................................... 245
Effects and tempo synchronization ....................................................................... 247
Parameters that can be assigned to control changes............................................. 248
NRPN parameter assignments .............................................................................. 250
Mixing parameter operation applicability ............................................................. 254
Functions that can be assigned to USER DEFINED keys ......................................... 259
Functions that can be assigned to USER DEFINED knobs....................................... 262
Functions that can be assigned to the assignable encoders................................... 263
MIDI Data Format ................................................................................................ 264
Warning/Error Messages....................................................................................... 271
Electrical characteristics ........................................................................................ 273
Mixer Basic Parameters......................................................................................... 274
MIDI Implementation Chart ................................................................................. 275
Index.................................................................................................................... 276
Function Tree
Reference Manual
4
Function Tree
Page numbers in parentheses ( ) are the page numbers of the
Owner’s Manual (booklet).
Main
SELECTED CHANNEL 6
OVERVIEW 12
FUNCTION ACCESS AREA (20)
CHANNEL PARAMETER
PATCH/NAME 16, 29, 48
GAIN/PATCH 31
1ch 31
8ch 32
CH1-48 32
CH49-72/ST IN 32
OUTPUT Indication only
INPUT DELAY 44
8ch 44
CH1-48 45
CH49-72/ST IN 45
DELAY SCALE 44
INSERT/DIRECT OUT 21
1ch 21, 23
8ch 22, 24
HPF/EQ 56
1ch 56
8ch 57
CH1-48 58
CH49-72/ST IN 58
OUTPUT 58
DYNAMICS 59
1ch 59
KEY IN SOURCE SELECT 62
8ch 61
CH1-48 62
CH49-72/ST IN 62
OUTPUT 62
SEND TO/SEND FROM 41, 52
TO STEREO/MONO 49
8ch 49
CH1-48 50
CH49-72/ST IN 50
OUTPUT 50
LIBRARY
CHANNEL LIBRARY 45
EQ LIBRARY 63
DYNAMICS LIBRARY 63
GEQ LIBRARY 137
EFFECT LIBRARY 137
Portico5033/Portico5043/U76/Opt-2A/
EQ-1A/DynamicEQ LIBRARY
137
DANTE INPUT PATCH LIBRARY 139
RACK
VIRTUAL RACK 115
RACK MOUNTER 116
GEQ EDIT 118
GEQ LINK 119
EFFECT RACK 122
EFFECT EDIT 125
EFFECT TYPE 126
PREMIUM RACK 130
PREMIUM RACK MOUNTER 131
PREMIUM RACK EDIT 132
I/O DEVICE
DANTE PATCH 138
DANTE SETUP 138
DANTE INPUT PATCH 138
DANTE OUTPUT PATCH 140
Rio 140
REMOTE HA EDIT 141
DANTE OUTPUT PATCH 142
AMP 143
DANTE OUTPUT PATCH 143
EXTERNAL HA 146
EXTERNAL HA EDIT 147
EXTERNAL HA PORT SELECT 147
MONITOR
MONITOR 98
CUE 103
MONITOR 99
OSCILLATOR 109
TALKBACK 107
METER
INPUT METER 111
OUTPUT METER 111
SETUP
USER SETUP 196
PREFERENCE 168
USER DEFINED KEYS SETUP 169
USER DEFINED KEY SETUP (List) 170
USER DEFINED KNOBS SETUP 171
USER DEFINED KNOB SETUP (List) 171
ASSIGNABLE ENCODER SETUP 172
CUSTOM FADER BANK/MASTER FADER 173
FADER ASSIGN SELECT 174
Function Tree
Reference Manual
5
NOTE
The explanations in this reference manual will use the CL5.
In the case of the CL3/CL1, some screens will not show
channels and faders that do not exist on those models.
USER LEVEL/CREATE USER KEY 158
CREATE KEY 160
SAVE KEY 165
LOGIN 161
SAVE/LOAD 177
WORD CLOCK/SLOT 198
CASCADE IN/OUT PATCH 200, 202
OUTPUT PORT 18
MIDI/GPI 149, 221
MIDI SETUP 150
PROGRAM CHANGE 152
CONTROL CHANGE 155
GPI 222
FADER START 225
BUS SETUP 202
CONSOLE LOCK 175
DATE/TIME 204
NETWORK 205
DANTE SETUP 213
SCENE
SCENE LIST 79
GLOBAL PASTE 85
FADE TIME 91
SONG SELECT 95
FOCUS RECALL 87
PREVIEW 96
RECORDER
USB 181
NUENDO LIVE 188
SETUP CH JOB
CH LINK MODE 71
DCA GROUP ASSIGN 64
MUTE GROUP ASSIGN 66
RECALL SAFE MODE 88
CH COPY MODE 73
CH MOVE MODE 74
CH DEFAULT MODE 76
PATCH
PORT SELECT
22, 24, 100, 104,
139, 201
CH SELECT
19, 117, 174,
175, 182
Others
CONFIRMATION 168
SOFT KEYBORD (21)
LOGIN 161
Startup Menu
MODE SELECT 206
INITIALIZE ALL MEMORIES 206
INITIALIZE CURRENT MEMORIES 206
TOUCH SCREEN CALIBRATION 207
INPUT PORT TRIM 210
OUTPUT PORT TRIM 210
SLOT OUTPUT TRIM 210
FADER CALIBRATION 208
CHANNEL COLOR CALIBRATION 211
SELECTED CHANNEL section
Reference Manual
6
SELECTED CHANNEL section
This chapter explains how to use the SELECTED CHANNEL section and the SELECTED CHANNEL
VIEW screen to control the selected channel.
About the SELECTED CHANNEL section
The SELECTED CHANNEL section located to the left of the display corresponds to the mixer module
on a conventional analog mixer, and enables you to manually adjust all the major parameters of the
currently-selected channel.
Operations in this section will affect the channel that was most recently selected by its [SEL] key. If you
have assigned an ST IN channel or STEREO channel to a single channel strip, either the L or the R
channel will be selected, and the major parameters for L and R channels will be linked. You can use the
knobs on the panel to control mix parameters such as head amp gain, HPF/EQ settings, the threshold
setting of the dynamics processors, pan/balance settings, and send levels to the MIX/MATRIX buses.
Operations in the SELECTED CHANNEL section
Follow the steps below to perform operations in the SELECTED CHANNEL section.
1. Use a [SEL] key to select the channel you want to control.
To select a channel, press a [SEL] key in the top panel channel strip section, the Centralogic
section, or the master section.
Press the appropriate bank select key so that the
channels you want to control are assigned to the
top panel.
The number and name of the currently-selected
channel is shown in the channel select field
located in the Function Access Area of the touch
screen.
NOTE
If an ST IN channel or STEREO channel has
been assigned to a single channel strip, you can switch between L and R by repeatedly pressing
the same [SEL] key.
You can also switch channels by pressing the channel select field located in the Function Access
Area. Press the left side of the field to select the preceding channel. Press the right side of the
field to select the next channel.
2. Press one of the knobs in the SELECTED CHANNEL section.
Press a knob in the SELECTED CHANNEL section to display the SELECTED CHANNEL VIEW
screen for the currently-selected channel. If you leave this screen displayed, you will always be able
to view the settings in the screen while operating the knobs in the SELECTED CHANNEL
section.
NOTE
If you have turned on the option “POPUP APPEARS WHEN KNOB(S) PRESSED” on the
PREFERENCE tab (accessed by pressing the SETUP button, then the USER SETUP button),
pressing a knob repeatedly will open or close the popup window (1ch).
Even if a different screen is selected, the knobs in the SELECTED CHANNEL section will always
affect the currently-selected channel. In this case, a window indicating the value of that parameter
will appear on screen when you operate a knob.
3. Use the knobs in the SELECTED CHANNEL section and the buttons on the
SELECTED CHANNEL VIEW screen to edit the parameters of the selected channel.
Channel number
Channel name
SELECTED CHANNEL section
Reference Manual
7
SELECTED CHANNEL VIEW screen
SEND field
In this field, you can view the send level from the channel to each MIX/
MATRIX bus, switch the on/off status of the send signals, and switch between
pre and post.
1 Tabs
Enable you to select a group of 16 output bus channels to be displayed
in the SEND field.
MIX1–16 tab.............................. displays MIX buses 1–16.
MIX17–24/MATRIX tab......... displays MIX buses 17–24 and
MATRIX buses 1–8.
The view and the function of the knobs and buttons in the SEND field vary
depending on whether a pair of bus channels (odd-numbered and even-
numbered) are comprised of two mono channels or a stereo channel.
If the destination bus channels are two mono channels:
1 SEND knob
Sets the send level to the corresponding bus.
2 PRE indicator
Indicates the send point of the corresponding bus. If the PRE button on the MIX SEND 8ch screen
is turned ON, this PRE indicator will be turned on.
3 ON button
Switches the send signal to the corresponding bus on or off.
If the destination bus is a stereo channel:
1 SEND/PAN knob
The right-hand knob adjusts the level of the signal sent to a pair of bus channels (even-numbered
and odd-numbered). The left-hand knob adjusts the pan and balance of the same signal.
2 PRE indicator
Indicates the send point of the corresponding bus. If the PRE button on the MIX SEND 8ch screen
is turned ON, this PRE indicator will be turned on.
3 ON button
Press the right-hand button to switch on or off the signal sent to two bus channels.
NOTE
If the indices of a SEND/PAN knob are white, the send point is assigned as PRE; if the indices
are black, it is assigned as POST.
If the send point is PRE, you can specify the PRE point as either VARI [PRE EQ] or VARI [PRE
FADER] in the BUS SETUP popup that appears when you press the SETUP button BUS
SETUP button.
If the type of the destination bus is set to FIXED, controllers
12 mentioned above will not be
displayed. The send level will be fixed at nominal level, and the send point will be fixed at POST
FADER. For details, see “Basic settings for MIX buses and MATRIX buses” on page 202.
Press the SEND LEVEL knob or PAN knob on screen to open the SEND 8ch popup window.
1
1
2
3
1
2
3
SELECTED CHANNEL section
Reference Manual
8
GAIN/PATCH field
This field enables you to make HA (head amp) analog gain settings, and view the operational status of
the head amp.
1 GAIN knob
Sets the analog gain of the head amp.
For a channel to which the head amp has not been
patched, a gray circle appears, instead of the knob. Press
the knob to open the GAIN/PATCH 1ch popup window.
If the Gain Compensation function is turned on, an
indicator appears, showing the level of the signal output
to the audio network.
2 OVER indicator
Warns you when the signal is clipping.
3 +48V indicator
Indicates the phantom power on or off status for the head amp.
4 Ø (Phase) indicator
Indicates the input phase setting for the head amp.
NOTE
For an input channel that is patched to an input that has no head amp, 1 will be a gray circle
and
3 will not be shown. For an output channel, 1 will be a gray circle, and 24 will not be
shown.
If GAIN KNOB FUNCTION is set to DIGITAL GAIN in the USER SETUP PREFERENCE
screen, the digital gain knob will appear for
1, and 3 will not be displayed.
For details, refer to “Making HA (Head Amp) settings” on page 30.
PAN/BALANCE field
This field enables you to switch the on/off status of the signal sent from the selected channel to the
STEREO/MONO bus, and adjust the pan and balance.
The view and the function of the controllers in this field vary depending on the type of the selected
channel.
When an input channel or MIX channel is selected:
1 TO STEREO PAN knob
Sets the pan position of a signal routed to the STEREO
bus.
Press the knob to open the STEREO/MONO 8ch popup
window. If the ST IN channel is selected, you can specify
whether to view the PAN knob or the BALANCE knob in
this popup window. For a MIX channel, the PAN knob
will appear if the signal is mono, and the BALANCE
knob will appear if the signal is stereo.
2 ST/MONO button
Switches the on/off status of a signal sent from the
channel to the STEREO/MONO bus.
If an INPUT/MIX channel is set to LCR mode, the LCR
button appears in location 2.
The LCR button is an overall on/off switch for the signals
sent from the channel to the STEREO/MONO bus.
When a MATRIX, STEREO, or MONO channel is selected:
1 BALANCE knob
If the signal on the selected channel is stereo, the
BALANCE knob will appear, enabling you to adjust the
volume balance for the left and right channels. If the
channel signal is monaural, a gray circle will appear in
this location.
Press the knob to open the TO STEREO 8ch popup
window.
INPUT DELAY field
This field enables you to view the delay settings.
1 ON indicator
Indicates the on/off status of the delay. If the delay is off,
the indicator will not be displayed.
2 Delay time
The delay value is displayed by milliseconds (ms) and also by currently-selected scale. If the scale
uses units of ms, the value in the bottom row will not be displayed. Only the ms value appears in
the middle row.
Press this field to open the INPUT DELAY 8ch popup window.
HPF field (input channels only)
This field enables you to set the HPF.
1 HPF knob
Sets the HPF cutoff frequency.
2 ON button
Switches the HPF on or off.
If an output channel is selected, a gray circle will appear in location
1, and button 2 will be hidden.
2
3
4
1
1 2
2
1
1
2
SELECTED CHANNEL section
Reference Manual
9
EQ parameter field
This field displays the 4-band EQ parameter settings.
1 Q knob
Specifies the Q for each band.
If the HIGH band filter type is set to LPF or H. SHELF (high-
shelving), or the LOW band filter type is set to L. SHELF (low-
shelving), the Q knob will not be displayed. Only the filter type
name will be displayed.
NOTE
Fully rotating the HIGH band Q knob on the panel counter-clockwise while pressing and holding
it down will set the filter type to LPF. Fully rotating the Q knob clockwise while pressing and
holding it down will set the filter type to high-shelving.
Fully rotating the LOW band Q knob on the panel clockwise while pressing and holding it down
will set the filter type to low-shelving.
If an output channel has been selected, fully rotating the LOW band Q knob on the panel counter-
clockwise while pressing and holding it down will set the filter type to HPF.
You can also switch the filter type on the HPF/EQ 1ch popup window.
2 FREQUENCY knob
Sets the center frequency (or cutoff frequency) for each band.
3 GAIN knob
Sets the amount of cut/boost for each band.
NOTE
If the HIGH band filter type is set to LPF, you can switch LPF on or off using the HIGH band GAIN
knob on the panel.
If the LOW band filter type is set to HPF, you can switch HPF on or off using the LOW band GAIN
knob on the panel.
Press each knob to open the HPF/EQ 1ch popup window.
EQ graph field
This field graphically indicates the approximate response of the EQ. Press this field to open the HPF/
EQ 1ch popup window, in which you can set the attenuator, HPF and EQ.
DYNAMICS 1/DYNAMICS 2 field
This field enables you to view and set the Dynamics 1/2 parameters.
1 OVER indicator
Warns you when the signal is clipping.
2 Level meter
Displays the output signal level (green) and the amount of gain reduction (orange) when the
Dynamics is on. The current threshold setting is shown as a white vertical line.
3 Threshold
Specifies the threshold.
4 Parameters
Indicate the values of parameters that vary depending on the currently-selected dynamics type.
Press this field to open the DYNAMICS 1/DYNAMICS 2 1ch popup window, in which you can
make detailed parameter settings.
1 2 3
1 2
3
4
SELECTED CHANNEL section
Reference Manual
10
INSERT field
This field enables you to make insert settings.
1 Popup button
Press this button to open the INSERT/DIRECT OUT 1ch
popup window.
2 ON button
Switches the insert on or off.
3 RACK EDIT popup button
Appears if an effect or Premium Rack is inserted. Press this button to display the edit screen for
the inserted rack.
4 IN indicator
Appears if a port has been assigned to the insert-in patch. It lights when the signal is sent to the
insert-in.
DIRECT OUT field
This field enables you to make insert settings.
1 Popup button
Press this button to open the INSERT/DIRECT OUT 1ch
popup window. The Direct Out level value will appear below
the button.
2 ON button
Switches the Direct Out on or off.
RECALL SAFE field
This field enables you to make Recall Safe settings.
1 Popup button
Press this button to open the RECALL SAFE popup window.
2 ON button
Switches the Recall Safe status on or off.
3 PARTIAL indicator
This will light if recall safe applies only to some of the parameters, not to all channel settings.
FADER field
This field enables you to view and make settings for the channel on/
off status and the level.
1 Fader
Displays the current level.
Use the faders on the top panel to set the levels.
2 Level indicator
Displays the current level setting by numerical value. If the
signal is clipping at any point in the channel, the ΣCLIP indicator will light.
3 ON button
Switches the channel status on or off. The button is linked with the corresponding [ON] key on
the top panel.
DCA/MUTE field
This field enables you to view and select the DCA or mute group to which
the channel is assigned.
1 Tabs
Select DCA or mute as a group to set. Press the selected tab once again
to open the DCA/MUTE GROUP ASSIGN MODE popup window.
When the DCA group tab is selected:
2 DCA group select buttons
Select the DCA group to which the channel is assigned.
3 Mute group indicators
Indicate the mute group to which the channel is assigned.
When the mute group tab is selected:
4 Mute group select buttons
Select the mute group to which the channel is assigned.
NOTE
If the dimmer level is set to the mute group, this button lights
orange.
5 MUTE SAFE button
Temporarily removes the channel from the mute group.
6 DCA group indicators
Indicate the DCA group to which the channel is assigned.
1
2
4 3
21
2
1
3
1
2
3
1
3
2
4
5
6
Centralogic section
Reference Manual
11
Centralogic section
This chapter explains how to use the Centralogic section and the OVERVIEW screen to simultaneously
control up to eight channels.
About the Centralogic section
The Centralogic section is located below the touch screen, and lets you recall and simultaneously
control a set of up to eight input channels, output channels, or DCA groups. Use the Bank Select keys
in the Centralogic section to select the channels that you want to control.
If you press one of the Bank Select keys, the channels or DCA groups corresponding to that key will be
assigned to the Centralogic section, and can be controlled using the faders, [ON] keys, and [CUE] keys
in the Centralogic section.
Operations in the Centralogic section
Follow the steps below to perform operations in the Centralogic section.
1. Use the Bank Select keys in the Centralogic section to select the channels or DCA
groups that you want to control.
When you press a Bank Select key, the LED of that key will light. The touch screen will display the
OVERVIEW screen, and the parameters of the eight channels you selected will appear.
NOTE
When the SELECTED CHANNEL VIEW screen is displayed, you can switch to the OVERVIEW
screen by pressing any of the multifunction knobs 1–8. This is convenient if you want to quickly
switch to the OVERVIEW screen while leaving the same channels or DCA groups selected for
control.
2. Use the faders and [ON] keys in the Centralogic section to adjust the level of the
group of up to eight selected channels and switch them on or off.
NOTE
The bottom line of the OVERVIEW screen shows the channels or DCA groups that can be
controlled by the faders, [ON] keys and [CUE] keys in the Centralogic section.
The top line of the OVERVIEW screen shows the channels that can be controlled by multifunction
knobs 1–8 in the Centralogic section.
3. Use the fields on the OVERVIEW screen and the multifunction knobs to adjust the
parameters for the group of up to eight channels.
Bank Select keys
Centralogic section
Reference Manual
12
OVERVIEW screen
CHANNEL NAME field
This field appears at the top and bottom of the screen and displays the channel number, name, and icon
for the currently-selected eight channels. The name of the currently-selected channel is highlighted.
NOTE
If you have retained the channels assigned to the faders in the Centralogic section by pressing
and holding down a Bank Select key, the channel names shown at the top and bottom of the
OVERVIEW screen may differ.
GAIN/PATCH field
This field enables you to make HA (head amp) analog or digital gain settings and view the operational
status of the head amp.
The view and the function of the controllers in this field vary depending on the type of the selected
channel.
If the head amp is patched:
1 GAIN knob
Sets the analog gain of the head amp.
Press this field to assign the GAIN knob to the corresponding
knob in the Centralogic section, which enables you to adjust the gain. If the Gain
Compensation function is turned on, an indicator appears, showing the level of the signal
output to the audio network.
If the GAIN knob has been assigned to a knob in the Centralogic section, press the knob to open
the GAIN/PATCH 8ch popup window.
2 OVER indicator
Lights when the signal at the input port or from the rack output exceeds the full scale level. This
indicator is available only if an input channel is selected.
3 +48V indicator
Indicates the phantom power (+48V) on or off status for the head amp. This indicator is not
displayed unless the head amp is patched to the channel.
4 Ø (Phase) indicator
Indicates the input phase setting for the head amp. This indicator is available only if an input
channel is selected.
NOTE
If the slot is not connected to the head amp, the patch and the type of the MY card will be
displayed.
If GAIN KNOB FUNCTION is set to DIGITAL GAIN in the PREFERENCE screen, the digital GAIN
knob will appear instead of knob
1, and indicator 3 will not be displayed.
If the Gain Compensation function is turned on, an indicator appears, showing the level of the
signal output to the audio network.
If the slot is patched:
The slot name will appear.
If the rack is connected:
The patch and module name will appear.
If the output is connected:
Only the patch will appear.
: Selected channel
: Unselected channel
1
4
3
2
Centralogic section
Reference Manual
13
INPUT DELAY field
This field displays the delay status for the input channel. If an output channel has been selected, this
field will be blank. Press this field to open the INPUT DELAY 8ch popup window.
1 DELAY ON/OFF indicator
Indicates the on/off status of the delay.
INSERT/DIRECT OUT field
This field enables you to make insert and Direct Out settings. Press this field to open the INSERT/
DIRECT OUT 8ch popup window.
1 INSERT ON/OFF indicator
Indicates the insert on/off status.
2 DIRECT OUT ON/OFF indicator (input channels only)
Indicates the Direct Out on/off status.
EQ field
This field graphically indicates the approximate response of the EQ.
Press this field to open the HPF/EQ 1ch popup window, in which
you can set the HPF and EQ.
NOTE
If DCA or monitor has been selected, this field will be blank.
DYNAMICS 1/2 field
This field displays the threshold value and meter for Dynamics 1/2.
Press this field to open the DYNAMICS 1/2 1ch popup window.
NOTE
If DCA or monitor has been selected, this field will be blank.
SEND field
This field displays the send level, send on/off status, and pre/post settings for 16
buses.
To select the 16 destination buses, use the [MIX 1–16] or [MIX 17–24/MATRIX]
key in the SELECTED CHANNEL section on the panel.
Use the Centralogic multifunction knobs to adjust the send level for each bus.
Touch the knob of the bus you want to operate; it will be assigned to the
Centralogic multifunction knobs. If it is assigned to the multifunction knobs,
touching that knob once again will display the SEND 8ch popup screen.
This field varies depending on the type of the destination bus.
If the destination bus is VARI (mono):
The knob color and scale color indicate the send on/off and pre/post status. If
the send is off, the knob color turns gray. With the post setting, the knob scale
color turns black.
If the destination bus is VARI (stereo):
If a pair of buses (odd-numbered and even-numbered) are in stereo, the left-
hand knob will function as the PAN knob, and the right-hand knob will function
as the SEND knob.
If the destination bus is set to FIXED:
The SEND ON/OFF button will appear instead of each knob.
1
1
2
Centralogic section
Reference Manual
14
TO STEREO/MONO field
This field displays the on/off status and pan/balance setting of the signal sent to the STEREO/MONO
bus.
If you press this field, the knob will be assigned to the corresponding knob in the Centralogic section.
If you press the field once again, the TO STEREO/MONO 8ch popup window will appear.
This field varies depending on the type of the selected channel.
When an input channel or MIX channel is selected:
1 TO STEREO PAN knob
Sets the pan position of a signal routed to the STEREO bus.
Press the knob to open the STEREO/MONO 8ch popup window. If the ST IN channel is selected,
you can specify whether to view the PAN knob or the BALANCE knob in this window. For a MIX
channel, the PAN knob will appear if the signal is mono, and the BALANCE knob will appear if
the signal is stereo.
2 ST/MONO indicator
Indicates the status of a signal sent to the STEREO/MONO bus.
If an input or MIX channel is set to LCR mode, the LCR indicator will
be displayed in location 2.
When a MATRIX channel (monaural) or MONO channel is selected:
The ΣCLIP indicator appears, indicating that the signal is clipping at some point in the channel.
For a stereo MATRIX channel or STEREO channel, the BALANCE knob appears, indicating the
balance of the left/right channels.
DCA group field
A DCA group (1–16) to which the channel is assigned is displayed on the first or second row in this
field.
Press this field to open the DCA/MUTE GROUP ASSIGN MODE popup window.
Mute group field
A mute group (1–8) to which the channel is assigned is displayed on the third row in this field. If the
channel has been temporarily removed from the mute group, “S” (Safe) will appear on the third row.
If the dimmer level has been set for a mute group, the color of the characters changes from red to
orange.
Press this field to open the DCA/MUTE GROUP ASSIGN MODE popup window.
1
2
2
Input and output patching
Reference Manual
15
Input and output patching
This chapter explains how to edit the input patching and output patching, how to connect inserts, and
how to use direct outputs.
CL console internal patching and Dante audio
network patching
The following diagram shows the signal flow through the CL series console, I/O devices, and Dante
audio network.
Input patching
CL series consoles and I/O devices feature two types of patching: Dante audio network patching and
CL console internal patching.
For Dante audio network patching, you will use the DANTE INPUT PATCH popup window. In this
window, you can patch CL console and I/O device inputs. Sixty-four (64) channels can be input from a
Dante audio network to a CL series console. You can choose up to 64 channels from maximum of 512
channels (logical value) of Dante audio network signals. Select the I/O devices (within 64 channels) that
you want to control from the CL series console.
Then, route the input signals (that were patched in the DANTE INPUT PATCH popup window) to
channels on the CL series console. To do this, choose input ports from DANTE 1–64 in the GAIN/
PATCH popup window.
NOTE
By default, DANTE 1–64 are assigned to input channels 1–64.
Output patching
Use the OUTPUT PORT popup window to patch CL consoles output channels and Dante audio
network. In this window, assign output channel signals to DANTE 1–64 ports.
NOTE
By default, MIX 1–24 are assigned to DANTE 1–24, MATRIX 1–8 are assigned to DANTE 25–32,
STEREO L/R are assigned to DANTE 33/34, and MONO is assigned to DANTE 35.
Next, patch the output signals from DANTE 1–64 (assigned in the OUTPUT PORT popup window) to
I/O device outputs. Use the OUTPUT PATCH popup window of the I/O device to make these
assignments.
64/512
8 16 16 16 64
SW
Dante-MY16-AUD
ID #3
ID #1
ID #2
OMNI MY MY MY
INPUT PATCH
Dante Network
“Dante” (ports)
CL series console
I/O device
I/O device
I/O device
Up to 512 channels
(logical value)
Dante
patching
CL internal
patching
Input and output patching
Reference Manual
16
Changing the output patch settings
To change the patching, you can either select the output port that will be the output destination of each
output channel, or you can select the output channel that will be the output source for each output port.
Selecting the output port for each output channel
1. Use the Bank Select keys in the Centralogic section to access the OVERVIEW screen
containing the output channel for which you want to assign the output port.
2. In the top part of the screen, press the channel number/channel name field to
access the PATCH/NAME popup window.
In the PATCH/NAME popup window you can change the channel name, icon, and output port
assigned to each output channel. The window includes the following items.
1 PATCH button
Indicates the port that is patched to the input or output channel. Press this button to enable the
PATCH tab at the bottom of the screen. The PORT SELECT popup window will appear, enabling
you to select the network and port.
2 Channel select button
Selects the channel to set.
NOTE
Switching channels on this screen will not affect the channel selection on the console.
3 Channel icon button
Indicates the icon and color that are currently selected for the corresponding channel. Press this
button to enable the ICON tab at the bottom of the screen. The CH COLOR/ICON popup
window will appear, enabling you to select the color, icon, and channel name.
4 Channel number display box
Indicates the channel number. This item cannot be changed.
Channel number/Channel name
3 54
1
6
7
2
Input and output patching
Reference Manual
17
5 Channel name edit box
Indicates the currently-specified channel. Press the inside of this box to enable the NAME tab at
the bottom of the screen. The SOFT KEYBOARD popup window will appear, enabling you to edit
the channel name.
6 Category select list
Selects the type of the port you want to display on the screen.
7 Port select buttons
Enable you to select a port in the current category. To cancel the selection, press the same button
once again.
3. Use the output port select tabs and the output port select buttons to specify the
output port that will be assigned to that channel.
If the output port select buttons are not shown at the bottom of the window, press the PATCH tab.
4. Use the Bank Select keys and the [SEL] keys to switch the output channels being
controlled, and specify their output ports in the same way.
5. When you have finished making settings, press the “x” symbol located in the upper
right to close the window.
You will return to the OVERVIEW screen.
Selecting the output channel for each output port
1. In the Function Access Area, press the SETUP button to access the SETUP screen.
2. In the SYSTEM SETUP field located in the center of the screen, press the OUTPUT
PORT button to open the OUTPUT PORT popup window.
OUTPUT PORT button
Input and output patching
Reference Manual
18
In the OUTPUT PORT popup window, you can assign the source channel for each output port.
This popup window includes the following items.
1 Slot number/Card type
If an output channel of slot 1–3 is selected for operations, this area indicates the slot number and
the type of I/O card installed in that slot.
2 DELAY SCALE button
Press this button to open the DELAY SCALE popup window, in which you can select the unit for
the delay time.
3 Output port
This is the type and number of the output port to which the channel is assigned.
4 Channel select popup button
Enables you to select the channel that you want to assign to the output port. The name of the
currently-selected channel is displayed.
5 Delay time knob
Sets the delay time of the output port. Press this knob to select it, and then use multifunction
knobs 1–8 to adjust the settings. The millisecond delay time value is indicated above the knob,
and the delay time value in the units selected in the DELAY SCALE popup window is indicated
below the knob.
NOTE
If you have selected ms (millisecond) as the scale, the delay time value will not appear above the
knob.
6 DELAY button
Switches the output port delay on or off.
7 Ø (Phase) button
Switches the phase of the signal assigned to the output port between normal phase and reverse
phase.
8 GAIN knob
Adjusts the output gain of the output port. To adjust this value, press the knob on screen to select
it, and then operate multifunction knobs 1–8. Rotate the knob to set the value in the range of –96
to +24 dB in 1.0 dB steps. Rotate the knob while pressing and holding it down to set the value in
0.1 dB steps. The current value appears immediately below the knob.
9 Level meter
Indicates the level of the signal assigned to the output port.
0 Output port select tabs
Switch the output ports controlled in the popup window in groups of up to eight ports. Tabs are
categorized into three groups: DANTE, SLOT, and PATCH VIEW. To display tabs in the desired
group, press the group name button located at the right or left end of the bottom row.
3. Use the output port select tabs at the bottom of the popup window to select the
output port you want to control.
The tabs correspond to the following output ports.
DANTE 1–8, 9–16, 17–24, 25–32, 33–40, 41–48, 49–56, 57–64
These tabs control the output channels of the Dante connectors.
SLOT1 1–8, 9–16
SLOT2 1–8, 9–16
SLOT3 1–8, 9–16
These tabs enable you to control output channels 1–8 and 9–16 of slots 1–3 respectively.
OMNI 1–8
This tab enables you to control OMNI jacks 1–8.
DIGITAL OUT
This tab enables you to control the L/R channels of the DIGITAL OUT connector.
•PATCH VIEW1
•PATCH VIEW2
These tabs display lists of patches.
4. To assign a channel to an output port, press the channel select popup window for
that port.
2
1
3
4
5
6
7
8
9
0
Input and output patching
Reference Manual
19
The CH SELECT popup window will appear. This popup window includes the following items.
1 Category select list
Selects the category of channel shown in the popup window. The categories correspond to the
following channels. They vary depending on the output port type.
MIX/MATRIX.................................. MIX 1–MIX 24, MATRIX 1–MATRIX 8
ST/MONO/MONI/CUE ................. STEREO L, STEREO R, MONO(C), MONI L, MONI R,
MONI C, CUE L, CUE R
DIRECT OUT 1–32......................... CH1–CH32 Direct Outs
DIRRECT OUT 33–64.................... CH33–CH64 Direct Outs
DIRECT OUT 65–72 ...................... CH65–CH72 Direct Outs
INSERT OUT 1–32.......................... CH1–CH32 Insert-outs
INSERT OUT 33–64 ....................... CH33–CH64 Insert-outs
INSERT OUT 65–72 ....................... CH65–CH72 Insert-outs
INSERT OUT MIX/MATRIX ....... Insert-outs for MIX1-MIX24, MATRIX 1-MATRIX8
INSERT OUT ST/MONO .............. Insert-outs for STEREO L, STEREO R, and MONO (C)
CASCADE MIX/MATRIX............. MIX1–MIX24, MATRIX1–MATRIX8
CASCADE ST/MONO/CUE.......... STEREO L, STEREO R, MONO(C), CUE L, CUE R
NOTE
In the case of the CL3/CL1, channels that do not exist on those models will not be shown.
2 Channel select buttons
Select the channel to be assigned to the output port you selected in step 3.
5. Use the channel select tabs and the channel select buttons to select the source
channel, and press the CLOSE button.
You will return to the OUTPUT PORT popup window.
NOTE
If PATCH CONFIRMATION is ON, a confirmation dialog box will appear when you attempt to
change the patch settings. If STEAL PATCH CONFIRMATION is ON, a confirmation dialog box
will appear when you attempt to change a location that is already patched elsewhere.
6. Make settings for delay, phase, and output gain as necessary.
7. Repeat steps 3–6 to assign channels to other output ports.
8. When you have finished making settings, click the “x” symbol in the upper right of
the window to return to the previous screen.
Changing the input patch settings
This section explains how to change the patching of each input channel.
1. Use the Bank Select keys in the Centralogic section to access the OVERVIEW screen
for the input channel to which you want to assign the input source.
2. In the top part of the screen, press the channel number/channel name field to
access the PATCH/NAME popup window.
1
2
Input and output patching
Reference Manual
20
In the PATCH/NAME popup window you can view and change the channel name, icon, channel
color, and input port assigned to each input channel.
1 PATCH button
Indicates the currently-selected input port. If you press this button when selecting an icon or
changing the channel name, you will return to the input port select screen.
2 Channel icon button
Indicates the icon that is selected for the corresponding channel. When you press this button, a
screen will appear in which you can select an icon or sample name.
3 Channel name input box
Indicates the name that is assigned to the corresponding channel. When you press this field, a
keyboard window allowing you to assign a name will appear.
4 Category select list
Selects the category of input port shown in the popup window. The categories correspond to the
following input ports. They vary depending on the channel type.
DANTE1–32 ..............DANTE1–DANTE32
DANTE33–64 ............DANTE33–DANTE64
OMNI/PB OUT.........OMNI1–OMNI8, PB OUT(L), PB OUT(R)
SLOT1 .........................SLOT1(1)–SLOT1(16)
SLOT2 .........................SLOT2(1)–SLOT2(16)
SLOT3 .........................SLOT3(1)–SLOT3(16)
EFFECT RACK......... FX1L(A)–FX8R(B)
PREMIUM RACK.... PR1L(A)–PR2R(B)
5 Input port select buttons
Assign an input port to the currently-selected input channel.
6 Tabs
Enable you to switch between items.
3. Access the input port selection screen of the PATCH/NAME popup window, and
then use the input port select tabs and input port select buttons to select an input
port.
NOTE
If PATCH CONFIRMATION is ON, a confirmation dialog box will appear when you attempt to
change the patch settings. If STEAL PATCH CONFIRMATION is ON, a confirmation dialog box
will appear when you attempt to change a location that is already patched elsewhere.
4. When you have finished making settings, press the “x” symbol located in the upper
right to close the window.
You will return to the OVERVIEW screen.
NOTE
You can also select input ports from the GAIN/PATCH popup window.
5. Repeat step 2–4 to assign input ports for other channels.
2 3
1
6
4
5
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277

Yamaha CL5/CL3/CL1 V1.5 Användarmanual

Kategori
Programvara
Typ
Användarmanual
Denna manual är också lämplig för