Yamaha RX-V1400 Användarmanual

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

HTR-5790

AV Receiver

OWNER'S MANUAL

U

Printed in Malaysia WC85700

HTR-5790U-cv.fm Page 1 Tuesday, November 18, 2003 11:12 AM

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert you to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle

is intended to alert you to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

1 Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and use instructions

should be followed.

5 Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners. Use

a damp cloth for cleaning.

6 Attachments – Do not use attachments not recommended by

the product manufacturer as they may cause hazards.

7 Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool;

and the like.

8 Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious

damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or sold

with the product. Any mounting of the product should

follow the manufacturer’s instructions, and should use a

mounting accessory recommended by the manufacturer.

9 A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven

surfaces may cause the product and cart

combination to overturn.

10 Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or other similar surface. This product should not

be placed in a built-in installation such as a bookcase or rack

unless proper ventilation is provided or the manufacturer’s

instructions have been adhered to.

11 Power Sources – This product should be operated only from

the type of power source indicated on the marking label. If

you are not sure of the type of power supply to your home,

consult your product dealer or local power company. For

products intended to operate from battery power, or other

sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having

one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and the

point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

15 Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touching

such power lines or circuits as contact with them might be

fatal.

16 Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result

in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch

dangerous voltage points or short-out parts that could result

in a fire or electric shock. Never spill liquid of any kind on

the product.

18 Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

19 Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the

product,

c) If the product has been exposed to rain or water,

IMPORTANT SAFETY INSTRUCTIONS

i

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

00_HTR-5790U_EN.book Page 2 Tuesday, December 9, 2003 9:16 AM

IMPORTANT SAFETY INSTRUCTIONS

3

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC – NATIONAL ELECTRICAL CODE

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the product to its normal

operation,

e) If the product has been dropped or damaged in any

way, and

f) When the product exhibits a distinct change in perfor-

mance - this indicates a need for service.

20 Replacement Parts – When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer or have the same

characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, or other

hazards.

21 Safety Check – Upon completion of any service or repairs to

this product, ask the service technician to perform safety

checks to determine that the product is in proper operating

condition.

22 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

23 Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

24 Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the antenna

or cable system is grounded so as to provide some

protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA 70,

provides information with regard to proper grounding of the

mast and supporting structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and, in particular, specifies

that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as

practical.

FCC INFORMATION (for US customers)

ii

1 IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC, to

use the product.

2 IMPORTANT: When connecting this product to

accessories and/or another product use only high quality

shielded cables. Cable/s supplied with this product MUST

be used. Follow all installation instructions. Failure to

follow instructions could void your FCC authorization to

use this product in the USA.

3 NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15

for Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will

not result in harmful interference with other electronic

devices.

This equipment generates/uses radio frequencies and, if

not installed and used according to the instructions found

in the users manual, may cause interference harmful to the

operation of other electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this

product is found to be the source of interference, which

can be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

00_HTR-5790U_EN.book Page 3 Tuesday, December 9, 2003 9:16 AM

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

4

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this sound system in a well ventilated, cool,

dry, clean place — away from direct sunlight, heat

sources, vibration, dust, moisture, and/or cold.

Allow ventilation space of at least 30 cm on the top,

20 cm on the left and right, and 20 cm on the back of

this unit.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds.

4 Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this unit

in a environment with high humidity (i.e. a room with

a humidifier) to prevent condensation inside this

unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may

fall onto this unit and/or this unit may be exposed to

liquid dripping or splashing. On the top of this unit,

do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall

and liquid may cause electrical shock to the user

and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If

the temperature inside this unit rises, it may cause

fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than specified

is dangerous and may cause fire, damage to this

unit, and/or personal injury. YAMAHA will not be

held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, disconnect the

power cord from the wall outlet during an electrical

storm.

14 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

15 When not planning to use this unit for long periods

of time (i.e. vacation), disconnect the AC power plug

from the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding that

this unit is faulty.

17 Before moving this unit, press STANDBY/ON to set

this unit in the standby mode, and disconnect the

AC power plug from the wall outlet.

18 VOLTAGE SELECTOR (Asia and General models

only)

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local main voltage BEFORE

plugging into the AC main supply.

Voltages are 110/120/220/230-240 V AC, 50/60 Hz.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association's Consumer

Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound

come through loud and clear without annoying blaring or

distortion - and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YA M A H A and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit itself

is turned off. This state is called the standby mode. In this

state, this unit is designed to consume a very small quantity of

power.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

iii

00_HTR-5790U_EN.book Page 4 Tuesday, December 9, 2003 9:16 AM

1

PREPARATIONINTRODUCTION

BASIC

OPERATION

SOUND FIELD

PROGRAMS

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

CONTENTS ............................................................ 1

FEATURES............................................................. 2

GETTING STARTED............................................ 3

Supplied accessories .................................................. 3

Installing batteries in the remote control ................... 3

CONTROLS AND FUNCTIONS ......................... 4

Front panel ................................................................. 4

Remote control........................................................... 6

Using the remote control ........................................... 7

Front panel display .................................................... 8

Rear panel ................................................................ 10

SPEAKER SETUP ............................................... 11

Speaker placement ................................................... 11

Speaker connections ................................................ 12

CONNECTIONS .................................................. 15

Before connecting components................................ 15

Connecting video components................................. 16

Connecting audio components................................. 19

Connecting the antennas.......................................... 21

Connecting the power supply cord .......................... 22

Speaker impedance setting ...................................... 23

Turning on the power............................................... 23

AUTO SETUP....................................................... 24

Introduction.............................................................. 24

Optimizer microphone setup.................................... 24

Starting the setup ..................................................... 25

BASIC SETUP...................................................... 28

Using BASIC setup.................................................. 28

PLAYBACK.......................................................... 30

Basic operations....................................................... 30

Selecting sound field programs ............................... 32

Selecting input modes.............................................. 34

TUNING ................................................................ 36

Automatic and manual tuning.................................. 36

Presetting stations .................................................... 37

Selecting preset stations........................................... 39

Exchanging preset stations ...................................... 39

RECORDING ....................................................... 40

SOUND FIELD PROGRAM

DESCRIPTIONS...............................................41

For movie/video sources.......................................... 41

For music sources .................................................... 43

ADVANCED OPERATIONS ..............................44

Selecting the OSD mode.......................................... 44

Using the sleep timer ............................................... 44

Manually adjusting speaker levels........................... 45

Using the test tone ................................................... 46

SET MENU ............................................................47

Using SET MENU................................................... 48

Manual setup: SOUND............................................ 49

Manual setup: INPUT.............................................. 54

Manual setup: OPTION........................................... 56

REMOTE CONTROL FEATURES ...................59

Control area ............................................................. 59

Setting manufacturer codes...................................... 60

Programming codes from other remote controls ..... 61

Changing source names in the display window....... 62

Clearing function sets .............................................. 63

Clearing individual functions .................................. 63

Controlling each component.................................... 64

ZONE 2/ZONE 3

(U.S.A., Canada and Australia models only)..68

Zone 2/Zone 3 connections...................................... 68

Remote controlling Zone 2/Zone 3.......................... 69

EDITING SOUND FIELD PARAMETERS ......71

What is a sound field ............................................... 71

Changing parameter settings ................................... 71

SOUND FIELD PARAMETER

DESCRIPTIONS...............................................73

TROUBLESHOOTING .......................................77

GLOSSARY...........................................................82

SPECIFICATIONS...............................................85

CONTENTS

INTRODUCTION

PREPARATION

BASIC OPERATION

SOUND FIELD PROGRAMS

ADVANCED OPERATION

ADDITIONAL INFORMATION

00_HTR-5790U_EN.book Page 1 Tuesday, December 9, 2003 9:16 AM

FEATURES

2

Built-in 7-channel power amplifier

◆ Minimum RMS output power

(0.04% THD, 20 Hz – 20 kHz, 8Ω)

Front: 110 W + 110 W

Center: 110 W

Surround: 110 W + 110 W

Surround Back: 110 W + 110 W

Sound field features

◆ Proprietary YAMAHA technology for the creation of

sound fields

◆ THX

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS ES Matrix 6.1, Discrete 6.1, DTS

Neo:6 decoder, DTS 96/24

◆ Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic

IIx Decoder

◆ Virtual CINEMA DSP

◆ SILENT CINEMA

™

Sophisticated AM/FM tuner

◆ 40-station random access preset tuning

◆ Automatic preset tuning

◆ Preset station shifting capability (preset editing)

Other features

◆ YPAO: YAMAHA Parametric Room Acoustic

Optimizer for automatic speaker setup

◆ 192-kHz/24-bit D/A converter

◆ “SET MENU” which provides you with items for

optimizing this unit for your audio/video system

◆ 6 or 8-channel external decoder input for other future

formats

◆ On Screen Display function helpful in controlling this

unit

◆ S Video signal input/output capability

◆ Component video input/output capability

◆ Video signal conversion (composite video ↔

S Video → component video) capability for monitor

out

◆ Optical and coaxial digital audio signal jacks

◆ Sleep timer

◆ Night listening mode

◆ Remote control with preset manufacturer codes

◆ Zone 2/Zone 3 custom installation facility (U.S.A.,

Canada and Australia models only)

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and product, the product has priority.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol

are trademarks of Dolby Laboratories.

SILENT CINEMA is a trademark of YAMAHA

CORPORATION.

“DTS” and “DTS-ES Digital Surround” and “Neo:6” are

trademarks of Digital Theater Systems, Inc.

THX and the THX logo are registered trademarks of THX Ltd.

Surround EX is a jointly developed technology of THX and

Dolby Laboratories, Inc. and is a trademark of Dolby

FEATURES

00_HTR-5790U_EN.book Page 2 Tuesday, December 9, 2003 9:16 AM

GETTING STARTED

3

INTRODUCTION

Please check that you received all of the following parts.

1 Press the part and slide the battery

compartment cover off.

2 Insert four supplied batteries (AAA, R03, UM-

4) according to the polarity markings on the

inside of the battery compartment.

3 Slide the cover back until it snaps into place.

Notes on batteries

• Change all of the batteries if you notice the condition like; the

operation range of the remote control decreases, the indicator

does not flash or its light becomes dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• If the batteries have leaked, dispose of them immediately.

Avoid touching the leaked material or letting it come into

contact with clothing, etc. Clean the battery compartment

thoroughly before installing new batteries.

GETTING STARTED

Supplied accessories

PHONO

POWER SLEEP

CLEAR

LEARN

STANDBY

TRANSMIT

RE–NAME

INPUT MODE

SYSTEM

V

-

AUX

DTV

POWER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDI O

VOL

LEVEL

MENU

STRAIGHT

STEREO

ENTERTAIN MUSIC TV THTR

NIGHT

EX/ES

MOVIE

THX /DTS

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

HALL

CHCH

JAZZ

ROCK

TITLE

MUTE

POWER

AMP

AVTV

DVR/VCR2VCR 1 DVD

SELECT

CBL/SAT MD/TAPE CD-R

TUNER CD

MULTI CH IN

+

–

3421

5

90

+10 ENTER

67 8

Remote control

Batteries (4)

(AAA, R03, UM-4)

Indoor FM antenna

(U.S.A., Canada, China,

Korea, Asia and General

models)

AM loop antenna

Optimizer microphone*

75-ohm/300-ohm antenna adapter

(U.K. model only)

Speaker terminal wrench

Power Cord

(U.S.A., Canada and Europe models)

(U.K., Europe and

Australia models)

*

The optimizer microphone is

sensitive to heat.

– Keep it away from direct

sunlight.

– Do not place it on top of this unit.

Installing batteries in the remote

control

1

3

2

If the remote control is without batteries for more than

3 minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries, set up the manufacturer code and program

any acquired functions that may have been cleared.

00_HTR-5790U_EN.book Page 3 Tuesday, December 9, 2003 9:16 AM

CONTROLS AND FUNCTIONS

4

1 STANDBY/ON

Turns on this unit or sets it to the standby mode. When

you turn on this unit, you will hear a click and there will

be a 4 to 5-second delay before this unit can reproduce

sound.

In standby mode, this unit consumes a small amount of power in

order to receive infrared-signals from the remote control.

2 Remote control sensor

Receives signals from the remote control.

3 Front panel display

Shows information about the operational status of this

unit.

4 PRESET/TUNING EDIT

Switches the function of PRESET/TUNING l / h

between selecting preset station numbers and tuning.

5 FM/AM

Switches the reception band between FM and AM.

6 A/B/C/D/E

Selects one of the 5 preset station groups (A to E).

7 PRESET/TUNING l / h

Selects preset station number 1 to 8 when the colon (:) is

displayed next to the band indication in the front panel

display.

Selects the tuning frequency when the colon (:) is not

displayed.

8 MEMORY (MAN’L/AUTO FM)

Stores a station in the memory. Hold down this button for

more than 3 seconds to start automatic preset tuning.

9 TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic (“AUTO”

indicator on) and manual (“AUTO” indicator off).

0 VOLUME

Controls the output level of all audio channels.

This does not affect the REC OUT level.

A OPTIMIZER MIC jack

Use to connect and input audio signals from the supplied

microphone for use with the AUTO SETUP function (see

page 24).

CONTROLS AND FUNCTIONS

Front panel

PRESET/TUNING

EDIT

FM/AM

A/B/C/D/E

PRESET/TUNING

INPUT MODE

TONE CONTROL

MULTI CH

INPUT

STRAIGHT

EFFECT

MEMORY

MAN'L/AUTO FM

TUNING MODE

AUTO/MAN'L MONO

VOLUME

PROGRAM INPUT

STANDBY

/ON

OPTIMIZER

MIC

PHONES

SILENT CINEMA

SPEAKERS

A B

OPTICALRAUDI OL

VIDEO

S VIDEO

VIDEO AUX

(U.S.A. model)

Note

00_HTR-5790U_EN.book Page 4 Tuesday, December 9, 2003 9:16 AM

CONTROLS AND FUNCTIONS

5

INTRODUCTION

B PHONES (SILENT CINEMA)

Outputs audio signals for private listening with

headphones. When you connect headphones, no signals

are output to the OUTPUT jacks or to the speakers.

All Dolby Digital and DTS audio signals are mixed down

to the left and right headphone channels.

C SPEAKERS A/B

Turn on or off the set of front speakers connected to the A

and/or B terminals on the rear panel at each time the

corresponding button is pressed.

D STRAIGHT/EFFECT

Switches the sound fields off or on. When STRAIGHT is

selected, input signals (2-channel or multi-channel) are

output directly from their respective speakers without

effect processing.

E PROGRAM

Use to select sound field programs or adjust bass/treble

balance (in conjunction with TONE CONTROL).

F TONE CONTROL

Use to adjust the bass/treble balance for the front left/right

and center channels (see page 31).

G INPUT MODE

Sets the priority (AUTO, DTS, ANALOG) for the type of

signals received when one component is connected to two

or more of this unit’s input jacks (see page 34). Priority

cannot be set when MULTI CH INPUT is selected as the

input source.

H INPUT selector

Selects the input source you want to listen to or watch.

I MULTI CH INPUT

Selects the source connected to the MULTI CH INPUT

jacks. When selected, the MULTI CH INPUT source

takes priority over the source selected with INPUT (or the

input selector buttons on the remote control).

J VIDEO AUX jacks

Input audio and video signals from a portable external

source such as a game console. To reproduce source

signals from these jacks, select V-AUX as the input

source.

00_HTR-5790U_EN.book Page 5 Tuesday, December 9, 2003 9:16 AM

CONTROLS AND FUNCTIONS

6

This section describes the function of each control on the

remote control. See “REMOTE CONTROL FEATURES”

on page 59 to operate other components with this remote

control.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 TRANSMIT indicator

Flashes while the remote control is sending signals.

3 STANDBY

Sets this unit in the standby mode.

4 SYSTEM POWER

Turns on the power of this unit.

5 Input selector buttons

Select the input source and change the control area.

6 Display window

Shows the name of the selected source component that

you can control.

7 LEVEL

Selects the speaker channel to be adjusted and sets the

level.

8 Cursor buttons u / d / j / i

Use to select and adjust DSP program parameters or SET

MENU items.

9 TEST

Outputs the test tone to adjust the speaker levels.

0 Sound field program/Numeric buttons

Use to select sound field programs or input numbers.

A RE-NAME

Used for changing the input source name in the display

window (see page 62).

B CLEAR

Used for clearing functions acquired when using the learn

and rename features, or setting manufacturer codes (see

page 63).

C LEARN

Used for setting up the manufacturer code or for

programming functions from other remote controls (see

pages 60 and 61).

D SLEEP

Sets the sleep timer.

E INPUT MODE

Sets the priority (AUTO, DTS, ANALOG) for the type of

signals received when one component is connected to two

or more of this unit’s input jacks (see page 34). Priority

cannot be set when MULTI CH INPUT is selected as the

input source.

F MULTI CH IN

Selects the MULTI CH INPUT mode when using an

external decoder (etc.).

G SELECT k/n

Selects another component that you can control

independently of the input component selected with the

input selector buttons.

H AMP

Selects AMP or other component selected by the input

selector button.

Remote control

PHONO

POWER SLEEP

CLEAR

LEARN

STANDBY

TRANSMIT

RE–NAME

INPUT MODE

SYSTEM

V

-

AUX

DTV

POWER

REC

DISC SKIP

SET MENU

TV INPUT

A/B/C/D/E

AUDIO

VOL

LEVEL

MENU

STRAIGHT

STEREO

ENTERTAIN MUSIC TV THTR

NIGHT

EX/ES

MOVIE

THX /DTS

TEST

ON SCREEN

EFFECT

CHP/INDEX

TV VOL

RETURN

DISPLAY

PRESET PRESET

TV MUTE

TV VOL

SELECT

HALL

CHCH

JAZZ

ROCK

TITLE

MUTE

POWER

AMP

AVTV

DVR/VCR2VCR 1 DVD

SELECT

CBL/SAT MD/TAPE CD-R

TUNER CD

MULTI CH IN

+

–

3421

5

90

+10 ENTER

67 8

00_HTR-5790U_EN.book Page 6 Tuesday, December 9, 2003 9:16 AM

CONTROLS AND FUNCTIONS

7

INTRODUCTION

I VOL –/+

Increases or decreases the volume level.

J MUTE

Mutes the sound. The MUTE indicator turns on when the

MUTE function is on. Press again to restore the audio

output to the previous volume level.

K SET MENU

Selects the SET MENU mode.

L ON SCREEN

Selects the on-screen display (OSD) mode for your video

monitor.

M STRAIGHT/EFFECT

Switches the sound fields off or on. When STRAIGHT is

selected, input signals (2-channel or multi-channel) are

output directly from their respective speakers without

effect processing.

N EX/ES

Switches between 5.1 or 6.1/7.1 channel playback of

multi-channel software.

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity such as near a bath

– high temperature such as near a heater or stove

– extremely low temperature

– dusty places

Using the remote control

PRESET/TUNING

EDIT

FM/AM

A/B/C/D/E

PRESET/TUNING

INPUT MODE

TONE CONTROL

MULTI CH

INPUT

STRAIGHT

EFFECT

MEMORY

MAN'L/AUTO FM

TUNING MODE

AUTO/MAN'L MONO

VOLUME

PROGRAM INPUT

STANDBY

/ON

OPTIMIZER

MIC

PHONES

SILENT CINEMA

SPEAKERS

A B

OPTICALRAUDIOL

VIDEO

S VIDEO

VIDEO AUX

30 30

TRANSMIT

RE–NAME

CLEAR

LEARN

POWER SLEEP

STANDBY

INPUT MODE

SYSTEM

PHONO TUNER CD

MULTI CH IN

V

-

AUX

CBL/SAT MD/TAPE CD-R

DTV DVR/VCR2VCR 1 DVD

SELECT

POWER

TV

POWER

AV

AMP

REC

DISC SKIP

AUDIO

VOL

LEVEL

TITLE

TV INPUT

TV VOL

SET MENU

MENU

A/B/C/D/E

MUTE

CH

TV MUTE

SELECT

CH

PRESET PRESET

TEST

RETURN

TV VOL

ON SCREEN

DISPLAY

STRAIGHT

EFFECT

STEREO

HALL

JAZZ

ROCK

12

34

56

8

ENTERTAIN

MUSIC

TV THTR

MOVIE

7

90

ENTER

+10

EX/ES

THX /DTS

NIGHT

CHP/INDEX

Approximately 6 m (20 ft)

00_HTR-5790U_EN.book Page 7 Tuesday, December 9, 2003 9:16 AM

CONTROLS AND FUNCTIONS

8

1 Decoder indicators

When any of this unit’s decoders function, the respective

indicator lights up.

2 Sound field indicators

Light to indicate the active DSP sound fields.

3 Input source indicators

A cursor lights to show the current input source.

4 CINEMA DSP indicator

Lights up when you select a CINEMA DSP sound field

program.

5 OPTIMIZER indicator

Lights up during the auto setup procedure and when the

auto setup speaker settings are used without any

modifications.

6 STEREO indicator

Lights up when this unit is receiving a strong signal for an

FM stereo broadcast while the “AUTO” indicator is lit.

7 AUTO indicator

Shows that this unit is in the automatic tuning mode.

8 MUTE indicator

Lights up while the MUTE function is on.

9 VOLUME level indicators

Indicate the volume level.

0 THX indicator

Lights up when a THX program is selected.

A PCM indicator

Lights up when this unit is reproducing PCM (pulse code

modulation) digital audio signals.

B Headphones indicator

Lights up when headphones are connected.

C SP A B indicators

Light up according to the set of front speakers selected.

Both indicators light up when both sets of speakers are

selected, or when bi-wiring.

D SILENT CINEMA indicator

Lights up when headphones are connected and a sound

field program is selected (see page 31).

E NIGHT indicator

Lights up when you select night listening mode.

F VIRTUAL indicator

Lights up when Virtual CINEMA DSP is active (see

page 34).

G SLEEP indicator

Lights up while the sleep timer is on.

H Multi-information display

Shows the current sound field program name and other

information when adjusting or changing settings.

I HiFi DSP

Lights when you select a HiFi DSP sound field program.

Front panel display

V–AUX

DVR/VCR2

VCR 1

CBL/SAT

DTV DVD

MD/TAPE

CD–R CD TUNER

PHONO

96

24

VIRTUAL

ZONE2

ZONE3

OPTIMIZER

HiFi DSP

PS PTY

RT CT

EON

PTY

HOLD

STEREO

TUNED

AUTO

MEMORY

MUTE

VOLUME

SLEEP

DIGITAL

PL

MATRIX

DISCRETE

PCMTHX

EX

NIGHT

SILENT

A B

SP

LFE

ft

mS

dB

96/24

LL C R

SL SB SR

(U.S.A., Canada and

Australia models only)

(U.K. and Europe models only)

Presence DSP sound field

Listening position

Left surround

DSP sound field

Right surround

DSP sound field

Surround back DSP sound field

00_HTR-5790U_EN.book Page 8 Tuesday, December 9, 2003 9:16 AM

CONTROLS AND FUNCTIONS

9

INTRODUCTION

J TUNED indicator

Lights up when this unit is tuned in to a station.

K MEMORY indicator

Flashes to show a station can be stored.

L 96/24 indicator

Lights up when a DTS 96/24 signal is input to this unit.

M LFE indicator

Lights up when the input signal contains the LFE signal.

N Input channel indicators

Indicate the channel components of current digital input

signal.

O Presence and surround back speaker

indicators

Indicate the connection of presence and/or surround back

speakers when using the SPEAKERS setting (page 29) or

SP LEVEL setting (page 50).

P ZONE 2/ZONE 3 indicators

(U.S.A., Canada and Australia models only)

Light up while Zone 2 or Zone 3 signal is output.

Q RDS indicators

(U.K. and Europe models only)

The name(s) of the RDS data offered by the currently

received RDS station light(s) up.

EON lights up when an RDS station that offers the EON

data service is being received.

PTY HOLD lights up while searching for stations in the

PTY SEEK mode.

00_HTR-5790U_EN.book Page 9 Tuesday, December 9, 2003 9:16 AM

CONTROLS AND FUNCTIONS

10

1 DIGITAL OUTPUT jacks

See page 19 for details.

2 Audio component jacks

See page 19 for connection information.

3 Video component jacks

See pages 16 and 18 for connection information.

4 REMOTE IN/OUT jacks

(U.S.A., Canada and Australia models only)

See page 69 for details.

5 CONTROL OUT jack

(U.S.A., Canada and Australia models only)

This is control expansion terminal for commercial use.

6 AC OUTLET(S)

Use to supply power to your other A/V components (see

page 22).

7 AC INLET (U.S.A. and Canada models only)

Use this inlet to plug in the supplied power cable (see

page 22).

8 DIGITAL INPUT jacks

See pages 16, 18 and 19 for details.

9 MULTI CH INPUT jacks

See page 17 for connection information.

0 ZONE 2 / ZONE 3 OUTPUT jacks

(U.S.A., Canada and Australia models only)

See page 68 for details.

A Antenna terminals

See page 21 for connection information.

B PRE OUT jacks

See page 20 for connection information.

C Speaker terminals

See page 12 for connection information.

D PRESENCE/ZONE 2 speaker terminals

(U.S.A., Canada and Australia models)

PRESENCE speaker terminals

(other models)

See page 12 for connection information.

< Asia and General models only >

FREQUENCY STEP switch

See page 21.

VOLTAGE SELECTOR

See page 22.

Rear panel

AC OUTLETS

GND

SPEAKERS

FRONT

SURROUND

FRONT

CENTER

PRE OUT

SUB

WOOFER

SURROUND BACK

/PRESENCE

SURROUND

SURROUND BACK

CENTER

R

L

R

L

R

L

R

L

CENTER

SUB

WOOFER

MONITOR OUT

MULTI CH INPUT OUTPUT

AUDIO AUDIO VIDEO

S VIDEO

DVD

DTV

CBL

/SAT

VIDEO

R

L

R

L

IN

(

PLAY

)

IN

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD

PHONO

IN

OUT

ZONE 2

ZONE 3

DVR/

VCR 2

VCR 1

CD-R

IN

FRONT (6CH)/SB (8CH)

SURROUND

TUNER

AM

ANT

GND

FM ANT

75Ω

UNBAL.

COMPONENT VIDEO

P

R

DVD

MONITOR OUT

DTV

P

B

Y

DIGITAL OUTPUT

DIGITAL INPUT

OPTICAL

MD

/

TAP E

CD-R

DVD

DTV

CBL/SAT

CD

DVD

DVR/

VCR 2

COAXIAL

+

–

+

–

+

–

+

––

–

+

–

A

B

PRESENCE/ ZONE 2

CONTROL OUTREMOTE

IN OUT

+12V 15mA MAX.

SINGLE

(U.S.A. model)

00_HTR-5790U_EN.book Page 10 Tuesday, December 9, 2003 9:16 AM

SPEAKER SETUP

11

PREPARATION

+

y

The speaker layout above shows the standard ITU-R speaker

setting. You can use it to enjoy CINEMA DSP, multi-channel

audio sources and THX.

Front speakers (FR and FL)

The front speakers are used for the main source sound plus

effect sounds. Place these speakers an equal distance from

the ideal listening position. The distance of each speaker

from each side of the video monitor should be the same.

Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). If for some reason it is not practical

to use a center speaker, you can do without it. Best results,

however, are obtained with the full system. Align the front

face of the center speaker with the front face of your video

monitor. Place the speaker centrally between the front

speakers and as close to the monitor as possible, such as

directly over or under it.

Surround speakers (SR and SL)

The surround speakers are used for effect and surround

sounds. Place these speakers behind your listening

position, facing slightly inwards, about 1.8 m (6 ft) above

the floor.

Surround back speakers (SBR and SBL)

The surround back speakers supplement the surround

speakers and provide for more realistic front-to-back

transitions. Place these speakers directly behind the

listening position and at the same height as the surround

speakers. They should be positioned at least 30 cm (12 in)

apart. Ideally, they should be positioned at the same width

as the front speakers.

Subwoofer

The use of a subwoofer, such as the YAMAHA Active

Servo Processing Subwoofer System, is effective not only

for reinforcing bass frequencies from any or all channels,

but also for high fidelity reproduction of the LFE (low-

frequency effect) channel included in Dolby Digital and

DTS software. The position of the subwoofer is not so

critical, because low bass sounds are not highly

directional. But it is better to place the subwoofer near the

front speakers. Turn it slightly toward the center of the

room to reduce wall reflections.

Presence speakers (PR and PL)

Presence speakers supplement the sound from the front

speakers with extra ambient effects produced by

CINEMA DSP (see page 41). These effects include

sounds that filmmakers intend to locate a little farther

back behind the screen in order to create more theater-like

ambience. Place these speakers at the front of the room

about 0.5 - 1 m (1 - 3 ft) outside the front speakers, facing

slightly inwards, and about 1.8 m (6 ft) above the floor.

■ Di-pole speaker layout

Either di-pole or direct radiating speaker types can be used

for THX surround. If you choose di-pole speakers, please

place the surround and surround back speakers according

to the speaker layout below.

SPEAKER SETUP

Speaker placement

60˚

30˚

PL

PR

SBR

SBL

FL

FR

C

SL

SR

80˚

SL

more than 30 cm

(12 inches)

1.8 m (6 ft)

FL

SR

SL

FR

C

SBR

SBL

30˚ 30˚

: Di-pole speaker

: Direction of di-pole speaker

00_HTR-5790U_EN.book Page 11 Tuesday, December 9, 2003 9:16 AM

12

SPEAKER SETUP

Be sure to connect the left channel (L), right channel (R),

“+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the

polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

• If you will use 6 ohm speakers, be sure to set this unit’s

speaker impedance setting to 6 ohms before using (see

page 23).

• Before connecting the speakers, make sure that the

power of this unit is off.

• Do not let the bare speaker wires touch each other or

do not let them touch any metal part of this unit. This

could damage this unit and/or speakers.

• Use magnetically shielded speakers. If this type of

speakers still creates the interference with the monitor,

place the speakers away from the monitor.

A speaker cord is actually a pair of insulated cables

running side by side. One cable is colored or shaped

differently, perhaps with a stripe, groove or ridges.

Connect the striped (grooved, etc.) cable to the “+” (red)

terminals on this unit and your speaker. Connect the plain

cable to the “–” (black) terminals.

1 Remove approximately 10 mm (3/8") of

insulation from the end of each speaker

cables.

2 Twist the exposed wires of the cable together

to prevent short circuits.

3 Unscrew the knob.

y

Supplied speaker terminal wrench is useful to screw or

unscrew knobs.

4 Insert one bare wire into the hole in the side

of each terminal.

5 Tighten the knob to secure the wire.

Connecting to PRESENCE/ZONE 2 or PRESENCE

speaker terminals

1 Open the tab.

2 Insert one bare wire into

the hole of each terminal.

3 Return the tab to secure

the wire.

Banana plug connections

(With the exception of U.K., Europe and Asia models)

First, tighten the knob and then insert the banana plug

connector into the end of the corresponding terminal.

Speaker connections

CAUTION

10 mm (3/8")

1

2

Red: positive (+)

Black: negative (–)

5

4

3

2

1

3

Banana plug

(With the exception of U.K., Europe

and Asia models)

00_HTR-5790U_EN.book Page 12 Tuesday, December 9, 2003 9:16 AM

13

SPEAKER SETUP

PREPARATION

AC OUTLETS

SPEAKERS

FRONT

CENTER

PRE OUT

SUB

WOOFER

SURROUND

SURROUND BACK

R

L

R

L

+

–

+

–

+

–

+

––

–

+

–

A

B

SINGLE

231

7 8 6

5

10

9

4

PRESENCE/ ZONE 2

Subwoofer

system

Center

speaker

Front speakers (A)

Surround back speakers

LeftRight

LeftRight LeftRight

Surround speakers

Front

speakers

(B)

1

2

3

4

5

6

9

10

8

7

Speaker layout

(U.S.A. model)

LeftRight

You can connect both surround back and presence speakers to this unit, but they do not output sound simultaneously.

• The surround back speakers output the surround back channel included in Dolby Digital EX and DTS ES software and only

operate when the Dolby Digital EX or DTS ES decoder is turned on.

• The presence speakers output ambient effects created by the DSP sound fields. They do not output sound when other sound fields

are selected.

Presence speakers

00_HTR-5790U_EN.book Page 13 Tuesday, December 9, 2003 9:16 AM

14

SPEAKER SETUP

■ FRONT terminals

Connect one or two speaker systems to these terminals. If

you use only one speaker system, connect it to either the

FRONT A or B terminals.

The Canada model cannot output to two separate speaker systems

simultaneously.

Bi-wired connection

The unit also allows you to make bi-wired connections to

one speaker system. Use two pairs of speaker cables fo

r

each speaker (one pair for the woofer and one pair for the tweeter/

mid-range). To use the bi-wired connections, press

SPEAKERS

A and SPEAKERS B on the front panel so that both SP A and

B light up on the front panel display.

■ CENTER terminals

Connect a center speaker to these terminals.

■ SURROUND terminals

Connect surround speakers to these terminals.

■ SUBWOOFER jack

Connect a subwoofer with built-in amplifier, such as the

YAMAHA Active Servo Processing Subwoofer System,

to this jack.

■ SURROUND BACK terminals

Connect surround back speakers to these terminals. If you

only connect one surround back speaker, connect it to the

left (L) terminals.

■ PRESENCE terminals

Connect presence speakers to these terminals.

*

If you are using either U.S.A., Canada or Australia model, you

can also use these speakers as Zone 2 speakers (see page 57).

Note

Bi-wired connection

FRONT

R

L

+

–

+

–

+

–

A

B

This unit

00_HTR-5790U_EN.book Page 14 Tuesday, December 9, 2003 9:16 AM

CONNECTIONS

15

PREPARATION

Do not connect this unit or other components to the mains

power until all connections between components are

complete.

■ Signal directions and cable indications

■ Analog jacks

You can input analog signals from audio components by

connecting audio pin cable to the analog jacks on this unit.

Connect red plugs to the right jacks and white plugs to the

left jacks.

■ Digital jacks

This unit has digital jacks for direct transmission of digital

signals through either coaxial or fiber optic cables. You

can use the digital jacks to input PCM, Dolby Digital and

DTS bitstreams. When you connect components to both

the COAXIAL and OPTICAL jacks, priority is given to

the input signals from the COAXIAL jack. All digital

input jacks are compatible with 96-kHz sampling digital

signals.

This unit handles digital and analog signals independently. Thus

audio signals input to the analog jacks are only output to the

analog OUT (REC) jacks. Likewise audio signals input to the

digital (OPTICAL or COAXIAL) jacks are only output to the

DIGITAL OUTPUT jacks.

Dust protection cap

Pull out the cap from the optical jack before you connect

the fiber optic cable. Do not discard the cap. When you are

not using the optical jack, be sure to put the cap back in

place. This cap protects the jack from dust.

■ Video jacks

This unit has three types of video jacks. Connection

depends on the availability of input jacks on your monitor.

The signals input through the VIDEO jack on this unit can

be output through the S VIDEO and COMPONENT

VIDEO jacks (see page 56). The signals input through the

S VIDEO jack can be output through the VIDEO jack

when V CONV. is set to ON (see page 56).

VIDEO jack

For conventional composite video signals.

S VIDEO jack

For S-video signals, separated into luminance (Y) and

color (C) video signals to achieve high-quality color

reproduction.

COMPONENT VIDEO jacks

For component signals, separated into luminance (Y) and

color difference (P

B, PR) to provide the best quality in

picture reproduction.

When signals are input through both the S VIDEO and VIDEO

jacks, signals input through the S VIDEO jack have priority.

CONNECTIONS

Before connecting components

Note

CAUTION

S

V

O

V

L

R

C

video signal direction

left analog cables

right analog cables

optical cables

coaxial cables

video cables

S-video cables

For analog signals

For digital signals

For video signals

audio signal direction

Note

VIDEO

S VIDEO

COMPONENT VIDEO

P

R

P

B

Y

00_HTR-5790U_EN.book Page 15 Tuesday, December 9, 2003 9:16 AM

16

CONNECTIONS

■ Connections for DVD playback

Connecting video components

GND

M

SUR

SUB

WOO

CENTER

SUB

WOOFER

MONITOR OUT

MULCH CH INPUT OUTPUT

AUDIO AUDIO VIDEO

S VIDEO

DVD

DTV

CBL

/SAT

VIDEO

R

L

R

L

IN

(

PLAY

)

IN

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD

PHONO

IN

OUT

ZONE 2

ZONE 3

DVR/

VCR 2

VCR 1

CD-R

IN

MAIN/SURROUND BACK

SURROUND

TUNER

75Ω

UNBAL.

AM

ANT

GND

FM ANT

COMPONENT VIDEO

P

R

DVD

MONITOR OUT

DTV

P

B

Y

DIGITAL OUTPUT

DIGITAL INPUT

OPTICAL

MD

/

TAPE

CD-R

DVD

CBL/SAT

CD

DVD

DTV

COAXIAL

LR

O

DVD player

Video

monitor

(U.S.A. model)

Optical out Video out

Audio out

Video in

00_HTR-5790U_EN.book Page 16 Tuesday, December 9, 2003 9:16 AM

Sidan laddas...

Yamaha RX-V1400 Användarmanual

Yamaha RX-V1400 Användarmanual

på andra språk

Relaterade papper

Andra dokument