Jacobsen 068019- Maintenance Manual

varumärke: Jacobsen

Modell: 068019-

Kategori: Gräsklippare

Typ: Maintenance Manual

VARNING

Sweden

A SIGNATURE CUT, TRUSTED FOR OVER 100 YEARS

VARNING: Om maskinen inte används på korrekt sätt kan den orsaka allvarliga skador. De som använder och sköter

denna maskin måste få utbildning om korrekt användning och varnas för farorna. Vidare måste de läsa hela

handboken innan de försöker ställa in, använda, justera eller underhålla maskinen.

WARNING

WARNING: If incorrectly used this machine can cause severe injury. Those who use and maintain this machine must

be trained in its proper use, warned of its dangers and must read the entire manual before attempting to set up,

operate, adjust or service the machine.

SAFETY, OPERATION & MAINTENANCE MANUAL

HANDBOK FÖR SÄKERHET, DRIFT OCH UNDERHÅLL

4358526-D-SE

RJL AHCC

LF Series - Lightweight Fairway Mower / Lättviktsklippare för fairway

LF550 / LF570 – 2WD & 4WD

KUBOTA D1803-M-DI-E3B

BAU / DDF / DDG Series

KUBOTA D1803-CR-E5B

BAV / BAY / BAW / CAA Series

KUBOTA V2403-M-DI-E3B

DGL / DGQ Series

KUBOTA V2403-CR-E5B

CAD / CAE Series

KUBOTA V1505-CR-TE5

DCU / DCV / DCW / DCY Series

1 CONTENTS

en-1

1Contents

FOREWORD

This manual contains adjustment, maintenance, and

troubleshooting instructions for your new Jacobsen

machine. This manual should be stored with the

equipment for reference during operation.

Before you operate your machine, you and each operator

you employ should read the manual carefully in its

entirety. By following the safety, operating and

maintenance instructions, you will prolong the life of your

equipment and maintain its maximum efficiency.

If additional information is needed, contact your

Jacobsen Dealer.

SERVICE SUPPORT MATERIAL

Qty. Part No. Description

4358526 Safety & Operation Manual

4358527 Parts Manual

Video, Operator Training

4299117 T4F/Stage 5 Engine Parts Manual

4358529 T4I Diesel Engine Parts Manual

TBD Service Manual

Qty. Part No. Description

This manual may not be reproduced in whole or in part without the express permission of TSV Technical Publications Department.

CALIFORNIA PROPOSITION 65

WARNING

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects and other reproductive harm.

CONTENTS 1

en-2

Contents

Introduction

2.1 Important.............................................................................3

2.2 Product Identification ..........................................................4

2.3 Serial Numbers ...................................................................4

2.4 Guidelines for the Disposal of Scrap Products ...................5

Safety

3.1 How to Operate Safely........................................................ 6

Specifications

4.1 Engine Specifications .......................................................11

4.2 Dimensions and Weights ..................................................12

4.3 Mower Specification..........................................................14

4.4 Hydraulic Specification......................................................14

4.5 Vibration Level ..................................................................15

4.6 Slopes............................................................................... 16

4.7 Cutting Unit Specification.................................................. 16

4.8 Recommended Lubricants................................................ 16

4.9 Accessories ......................................................................17

4.10 Support Literature ...........................................................18

Labels

5.1 Safety Labels ....................................................................22

5.2 Instruction Labels.............................................................. 25

Controls

6.1 Operator Compartment.....................................................26

6.2 Armrest ............................................................................. 27

6.3 LDU...................................................................................32

6.4 Traction Pedal................................................................... 36

6.5 Steering Wheel Tilt Adjustment.........................................36

6.6 Seat Controls ....................................................................36

6.7 Throttle Lever (T4I Engines Only).....................................37

Operation

7.1 Daily Inspection ................................................................38

7.2 Interlock System ...............................................................39

7.3 Operating Procedure ........................................................40

7.4 Starting The Engine ..........................................................41

7.5 To Stop The Engine..........................................................41

7.6 Driving............................................................................... 42

7.7 Mowing Speed ..................................................................42

7.8 Mowing .............................................................................42

7.9 Mowing On Slopes............................................................ 43

7.10 Towing The Mower ......................................................... 45

Maintenance and Lubrication Charts

8.1 Maintenance Chart ...........................................................46

8.2 Lubrication Chart ..............................................................47

8.3 Fluid Requirements...........................................................47

Maintenance

9.1 General Precautions .........................................................48

9.2 Maintenance Mode ........................................................... 48

9.3 Engine............................................................................... 51

9.4 Engine Oil .........................................................................52

9.5 Engine Air Filter ................................................................ 53

9.6 Fuel...................................................................................53

9.7 Fuel System......................................................................54

9.8 Battery ..............................................................................55

9.9 Charge the battery ............................................................56

9.10 Engine Exhaust............................................................... 56

9.11 Diesel Particulate Filter (T4F/Stage 5 Engines Only) ..... 57

9.12 Hydraulic Hoses.............................................................. 59

9.13 Hydraulic Fluid................................................................ 60

9.14 Hydraulic Filter................................................................60

9.15 Tires................................................................................ 60

9.16 Wheel Mounting Procedure ............................................ 61

9.17 Radiator .......................................................................... 61

9.18 Folding ROPS................................................................. 62

9.19 To Backlap the Reels......................................................63

9.20 Electrical System ............................................................ 64

9.21 Care and Cleaning.......................................................... 66

9.22 Mower Storage ............................................................... 67

Adjustments

10.1 General Precautions....................................................... 68

10.2 Engine Fan Belt ..............................................................68

10.3 Steering Adjustment ....................................................... 69

10.4 Front Reel Limit Switch................................................... 69

10.5 Armrest Height Adjustment............................................. 70

10.6 Armrest Pivot .................................................................. 71

10.7 Bedknife-To-Reel............................................................ 71

10.8 Bedknife Adjustment....................................................... 72

10.9 Cutting Height.................................................................72

10.10 Down Pressure ............................................................. 73

10.11 Flash Attach™ .............................................................. 74

10.12 Bedknife Adjuster Spring .............................................. 75

10.13 Bedknife Adjuster Tension............................................ 75

10.14 Grinding the Bedknife ................................................... 75

10.15 Torque Specification .....................................................76

Problem Solving

11.1 General...........................................................................77

11.2 Controller ........................................................................ 78

Quality of Cut

12.1 Quality of Cut Problem Solving....................................... 79

12.2 Washboarding................................................................. 79

12.3 Marcelling .......................................................................80

12.4 Step Cutting....................................................................81

12.5 Scalping.......................................................................... 82

12.6 Stragglers .......................................................................83

12.7 Streaks............................................................................ 84

12.8 Windrowing..................................................................... 85

12.9 Rifling or Tramlining........................................................ 86

12.10 Mismatched Cutting Units............................................. 87

Notes

2 INTRODUCTION

en-3

2Introduction

2.1 IMPORTANT ______________________________________________________________

The Jacobsen LF550 / LF570 with a Diesel engine is a self propelled fairway mower. The hydraulic systems are for the

traction drive, steering, lift - lower and the cutting unit drive.

If you follow all instructions in this manual, you increase the life of your mower and keep its maximum performance.

Adjustments and maintenance must always be done by an approved technician.

IMPORTANT: Do the maintenance included in this manual to make sure that the quality of cut is kept at a high level.

This SAFETY, OPERATION AND MAINTENANCE MANUAL is part of the mower and must stay with the mower

always. Suppliers of both original and used mowers need to keep the documentation that comes with the mower.

You must use the mower to cut the grass and not for any other purpose. Compliance with the conditions or operation,

service and repair specified by the manufacturer, are understood to be part of the correct use.

ALL operators MUST read through this manual and understand the Safety Instructions, controls, lubrication and

maintenance procedures.

Make sure that you obey all safety and road traffic regulations.

You must not make any changes to the mower that the manufacturer does not approve. This type of change can

release the manufacturer from the liability for any damage or injury.

When you discard worn parts, know the environmental result and use the systems available in the country where the

mower is used. When the mower is at its end of life, there are guidelines in this manual for the removal of the mower

from use.

Use only Jacobsen approved parts.

2006/42/EC

The instructions recorded here are the original instructions confirmed by Jacobsen.

INTRODUCTION 2

en-4

2.2 PRODUCT IDENTIFICATION TEST ____________________________________________

Mower Serial number plate

A Maximum Front Axle Load in Kg

B Gross vehicle Weight in Kg

C Maximum Rear Axle Load in Kg

D Power in kw

E Date code

F Machine type (Designation)

G Product code

H Product name

J Serial Number

Location of Mower Serial number plate

The serial number plate (A) is found on the right side frame

rail behind the rear cutting units.

Engine Serial Number

The engine serial number is found on the top of the valve

cover toward the front of the mower. Label shows the

engine group and serial number.

The engine serial number is also found on the engine block.

2.3 SERIAL NUMBERS_________________________________________________________

Record the mower and engine numbers shown below:

Mower Number:_________________________

Engine Number:__________________________

Kg Kw

Kg Kg

West Road

Ransomes Europark

Ipswich IP3 9TT

England

ABCD E

105dB

LWA

11524 WILMAR BLVD,

CHARLOTTE, NC 28273

kg kW

1-800-848-1636 (US)

PRODUCT OF U.S.A. A Textron Company

xxxx xxxx xxxx

68012001601

V2403

S/N KEAXXXXX

Contact KEA for Parts

MADE IN JAPAN

2 INTRODUCTION

en-5

2.4 GUIDELINES FOR THE DISPOSAL OF SCRAP PRODUCTS _______________________

2.4.1 DURING SERVICE LIFE_____________________________________________________

The used oil, oil filters and engine coolant are hazardous materials. Follow the recommended procedures for their safe

removal.

If a fluid leaks, contain the spill to make sure that the leak does not flow into the ground or drainage system. Follow the

local laws to make sure that leaks are controlled safely.

The maintenance procedures in this manual make sure that the damage that the mower can cause in the local

environment is controlled safely.

Take these actions after the mower complete its full service life.

2.4.2 END OF SERVICE LIFE _____________________________________________________

Use these guidelines with applicable Health, Safety and Environmental laws. Always use the approved local waste

disposal and agencies for recycled materials.

• Park the mower in a location to use all of the necessary lifting equipment.

• Use the correct tools and Personal Protective Equipment (PPE) and take instruction from the technical manuals

applicable to the mower.

• Remove and keep correctly

1. Batteries

2. Fuel

3. Engine coolant

4. Oils

• Disassemble the structure of the mower and refer to the technical manuals. Give attention to parts that have

mechanical pressure or tension applied to the part in the mower, including springs.

• Separate items that continue to have service life and returned to storage.

• Separate items that are worn into the material groups and removed according to the agencies for the recycled

materials that are available. Common types are as shown:

• Steel

• Non ferrous metals

• Aluminum

• Brass

• Copper

• Plastic Materials

• Identified

• Can be recycled

• Can not be recycled

• Not Identified

• Rubber

• Electrical and Electronic Components

• Add items that can not be easily separated into different materials to the “General discarded materials” area.

• Do not burn the discarded materials

Change the mower records to show that the mower is not in service and is discarded. Supply this serial number to

Jacobsen Warranty Department to close their records.

SAFETY 3

en-6

3Safety

3.1 HOW TO OPERATE SAFELY _______________________________________________________

3.1.1 SAFE OPERATION _________________________________________________________

a Read the Operator’s Manual and other training material. If the operator or technician can not read this manual,

the owner is responsible to describe this material to the operators and technicians. Manuals in additional

languages may be available on the Jacobsen website.

b Read all of the instructions for this mower carefully. Know the controls and the correct operation of the

equipment.

c Children or other people who do not understand these instructions must not use the mower. The local regulations

can limit the age of the operator.

d Never use a mower near bystanders, including children or animals.

e Remember that the operator or owner is responsible for accidents or hazards that occur to other people or their

property.

f Never carry passengers.

g Never allow anyone to operate or service the mower or its attachments without correct instructions.

h Do not operate equipment while tired, sick or after you use alcohol or drugs.

3.1.2 PREPARATION ____________________________________________________________

a When you operate the mower, wear correct clothing, slip resistant work shoes or boots, work gloves, hard hat,

safety glasses and hearing protection. Long hair, loose clothing or jewelry can be caught in moving parts.

b Do not operate the equipment with the Interlock System disconnected or the system does not operate correctly.

Do not disconnect or prevent the operation of any switch.

c Never operate equipment that is not in correct order or without labels, guards, shields, deflectors or other

protective devices fastened.

d Inspect the mower before you operate the mower. Check the tire pressure, engine oil level, the radiator coolant

level and the air cleaner indicator. Fuel is flammable. Use caution when you add the fuel to the mower.

e Operate the mower in daylight or in good artificial light. Use caution when you operate the mower during bad

weather. Never operate the mower with lightning in the area.

f Inspect the area to select the accessories and attachments that are needed to correctly and safely do the job.

Only use parts, accessories and attachments approved by Jacobsen.

g Be careful of holes in the terrain and other hazards that are not visible.

h Inspect the area where the equipment is operated. Remove all objects you can find before you operate. Be

careful of obstructions above the ground (low tree limbs, electrical wires) and also underground obstacles

(sprinklers, pipes, tree roots). Enter a new area carefully. Look for possible hazards.

i Inspect the cutting system before you start the mower. Make sure the blades are free to rotate. When you rotate

one blade, other blades can rotate.

WARNING

EQUIPMENT OPERATED INCORRECTLY OR WITHOUT TRAINING CAN BE DANGEROUS.

Know the location and correct operation of controls. Operators without experience must receive instruction from

another person that knows the correct operation of the equipment before you operate the mower.

Only use parts, accessories and attachments approved by Jacobsen.

3 SAFETY

en-7

3.1.3 OPERATION ______________________________________________________________

a Never operate the engine without enough ventilation or in an enclosed area. The carbon monoxide in the

exhaust fumes can increase to dangerous levels.

b Never carry passengers. Keep bystanders or animals away from the mower.

c Disengage all drives and engage the parking brake before you start the engine. Only start the engine with the

operator in the seat. Never start the engine with anyone standing near the mower.

d Keep your legs, arms and body inside the operator compartment while the mower is in operation. Keep your

hands and feet away from the cutting units.

e Do not use on the slopes greater than the safe slope limit for the equipment.

f To guard against over turning or loss of control:

• Operate the mower up and down on the face of slopes (vertically), but not across the face (horizontally).

• Do not start or stop suddenly on slopes.

• Decrease the speed when you operate on slopes or when you must turn. Use caution when you change

direction. Turf condition can change the mower stability.

• Use caution when you operate the mower near drop-offs, ditches or embankments.

• Be careful of holes in the terrain and other hazards that are not visible.

g When you drive in the reverse direction, look behind you and down to make sure the path is clear. Do not operate

the cutting units when you drive in the reverse direction.

h Use caution when you go near corners, trees or other objects that can prevent a clear view.

i Equipment must meet the current regulations to be driven on the public roads.

j Before you move across or operate on the paths or roads, turn off the PTO switch, lift the mowers and travel at

decreased speed. Look for traffic.

k Stop the blades when the mower is on any surface that is not grass.

l Do not release the cut grass in the direction of bystanders or allow bystanders near the mower while in operation.

m Do not operate the mower with damaged guards or without safety devices in position.

n Do not change the engine governor setting or over-speed the engine. Never change or tamper with adjusters that

are closed with a seal for the engine speed control.

o Before you leave the operator compartment, for any reason:

• Disengage all the drives and lower attachments to the ground.

• Engage the parking brake.

• Stop the engine and remove the key.

p When you hit an object or mower starts to cause the vibration that is not normal, inspect the mower for damage

and make repairs.

q Decrease the throttle setting before you stop the engine.

r Do not use this equipment for uses that the mower was not made for.

SAFETY 3

en-8

3.1.4 ROPS____________________________________________________________________

a The ROPS is a safety device. Keep the ROPS in the vertical and locked position. Always use the seat belt when

you operate the mower. Make sure the seat belt can be released quickly in an emergency.

b Only operate the mower with the ROPS in the folded position on flat and level surfaces when necessary. Do not

operate the mower with the ROPS in the folded position on slopes, near sharp edges or near water. There is no

roll over protection with the ROPS in the folded position.

c Check for clearance before you drive below objects. Do not contact tree branches, electrical wires or other

objects with the ROPS.

d Do not use the seat belt with the ROPS in the folded position.

e Inspect the ROPS for damage. Keep the ROPS hardware fastened.

f Do not weld, drill, change or bend the ROPS. Replace a damaged ROPS. Do not try to correct a damaged

ROPS.

g Do not remove the ROPS from the mower.

h Jacobsen must approve any changes to the ROPS.

3.1.5 SAFE HANDLING OF FUELS ________________________________________________

a The fuel and the fuel vapors are flammable. Use caution when you add the fuel to the mower. The fuel vapors

can cause an explosion.

b Never use the containers that are not approved to keep or transfer fuel.

c Never keep the mower or fuel containers near an open flame or any device that can cause the ignition of fuel or

fuel vapors.

d Never fill the fuel containers inside a vehicle or on a truck or trailer with a plastic liner. Always put the fuel

container on the ground away from your vehicle before you fill the container.

e Refuel the mower before you start the engine. When the engine is in operation or while the engine is hot, never

remove the fuel cap or add fuel to the mower.

f Refuel outdoors only and do not smoke when you add fuel. Extinguish all types of ignition.

g The fuel nozzle must touch the rim of the fuel tank when you add fuel to the mower. Do not use a device to lock

the fuel nozzle in the open position.

h Do not over fill the fuel tank. Leave at least 1 inch (2.5 cm) below the filler neck.

i Always tighten the fuel tank cap and container cap after you add fuel.

j If the fuel spills on your clothing, change your clothing immediately.

3.1.6 MAINTENANCE AND STORAGE______________________________________________

a Before you clean, adjust or repair this equipment, push PTO switch to the OFF position, lower the cutting unit to

the ground, engage the parking brake, stop the engine and remove the key.

b Make sure the mower is parked on a solid and level surface.

c Never work on a mower that is lifted only by the jack. Always use the jack stands.

d Never allow anyone to service the mower or its attachments without correct instructions.

e When the mower is parked, put into storage or left without an operator, lower the cutting device unless a positive

mechanical lock is used.

f When you put the mower on a trailer or put the mower in storage, close the fuel valve. Do not keep fuel near

flames or drain the fuel inside a building.

3 SAFETY

en-9

g Disconnect the battery before you service the mower. Always disconnect the negative battery cable before the

positive battery cable. Always connect the positive battery cable before the negative battery cable.

h Charge the battery in an area with good airflow. The battery can release hydrogen gas that is explosive. To

prevent an explosion, keep any device that can cause sparks or flames away from the battery.

i Disconnect the battery charger from the power supply before you connect or disconnect the battery charger to

the battery. Wear protective clothing and use insulated tools when you service the battery.

j Be careful and wear gloves when you check or service the cutting unit blades. Replace any damaged blades, do

not try to correct a damaged blade.

k Keep your hands and feet away from parts that move. Do not adjust the mower with the engine in operation,

unless the adjustment needs the engine in operation.

l Carefully release the pressure from components with stored energy.

m To prevent injury from the hot, high pressure oil, never use your hands to check for oil leaks. Use the paper or

cardboard to find leaks.

n The hydraulic fluid pressure can have enough force to enter your skin. If hydraulic fluid has entered your skin, a

doctor must remove the hydraulic fluid surgically within a few hours or gangrene can occur.

o When you service the hydraulic system, make sure the hydraulic fittings, tubes and hoses are tightened to the

correct torque. Make sure the hydraulic system is in good condition before you start the engine.

p Keep the mower and the engine clean.

q Allow the engine to become cool before storage and always remove the ignition key.

r Keep all nuts, bolts and screws tight to make sure the equipment is in safe condition.

s Replace worn or damaged parts for safety. Replace damaged or worn labels. Only use parts, accessories and

attachments approved by Jacobsen.

t To decrease the fire hazard, remove materials that burn from the engine, muffler, battery tray and fuel tank area.

u Disconnect the battery and controller connectors before you weld on this mower.

3.1.7 WHEN YOU PUT THE MOWER ON A TRAILER__________________________________

a Be careful when you load or unload the mower on a trailer. Trailer must be wider than the mower and can carry

the weight of the mower.

b Use a full-width ramp to load or unload the mower on a trailer.

c Use straps, chains, cables or ropes to fasten the mower to the trailer. Both front and rear straps must be sent

down and toward sides of trailer.

d Make sure that all latches are correctly fastened.

SAFETY 3

en-10

3.1.8 IMPORTANT SAFETY NOTES ________________________________________________

This safety alert symbol gives a warning of possible hazards.

DANGER - Indicates a dangerous condition that WILL cause death or injury unless it is prevented.

WARNING - Indicates a dangerous condition that CAN cause death or injury unless it is prevented.

CAUTION - Indicates a dangerous condition that can cause injury and property damage unless it is prevented. The

label can indicate work procedures that are not safe.

NOTICE - Indicates a condition that can cause damage to the property unless it is prevented. The label can indicate

work procedures that are not safe.

Some illustrations in this manual show the shields, guards or plates, removed. Do not operate this equipment without

these devices correctly fastened in position.

If additional information or service is needed, contact your Authorized Jacobsen Dealer. Your Dealer knows the current

methods to service this equipment.

WARNING

The Interlock System on this mower prevents the engine from starting unless a.) The parking brake switch is in the

ON position. b.) The PTO switch is in the OFF position and c.) the traction pedal is in the Neutral position. The

system will stop the engine if the operator leaves the seat without:

a.) The parking brake switch in the ON position and

b.) the PTO switch in the OFF position.

NEVER operate the mower unless the Interlock System operates correctly.

WARNING

1. Before you leave the operator position, for any reason:

a. Return the traction pedal to Neutral.

b. Disengage all drives.

c. Lower the mowers to the ground.

d. Engage the parking brake.

e. Stop the engine and remove the ignition key.

2. Keep your hands, feet and clothing away from moving parts. Wait for all movement to stop before you clean,

adjust or service the mower.

3. Keep bystanders and animals away from the area of operation.

4. Never carry passengers.

5. Never operate the equipment without a correctly fastened grass deflector in position.

4 SPECIFICATIONS

en-11

4Specifications

4.1 ENGINE SPECIFICATIONS __________________________________________________

Make Kubota

Tier 4 Interim (T4I) Engine Tier 4 Final/Stage V (T4F/Stage 5) Engines

Model D1803-M-DI-E3B V2403-M-DI-E3B D1803-DICR-E4B V2403-DICR-E4B/E5B V1505-CR-TE5

Type Four cycle, liquid cooled, Diesel

Number of

Cylinders

3 4 3 4 4

Bore and

Stroke

3.43 in. (8.7 cm) x 4.03 in. (10.24 cm) 3.07 in (78mm) X 3.09

in (78.4mm)

Total

Displacement

111.43 in3 (1.826 l) 148.5 in3 (2.434 l) 111.43 in3 (1.826 l) 148.5 in3 (2.434 l) 94.14 in3 (1.498 l)

Combustion

System

Direct Injection Common Rail Direct Injection

Intake System Naturally Aspirated Turbo

Gross

Intermittent

Power

35.5 hp (26.5 kw)

@ 2700 RPM

47.1 hp (35.1 kw)

@2700 RPM

37.5 hp (28 kW)

@ 2700 rpm

50.2 hp (37.4 kW)

@ 2700 rpm

44.9hp (33.0 kW)

@ 3000 rpm

Torque 83.1 ft.lb. (112.7 Nm)

@ 1600 rpm

114.5 ft.Lb. (155.2 Nm)

@1600 rpm

85.4 ft.Lb. (115.8 Nm)

@1600 rpm

117.9 ft.Lb. (159.8 Nm)

@1600 rpm

87.5 ft.Lb. (118.6 Nm)

@2000 rpm

Maximum

Speed

2920 ± 50 rpm (No

Load)

2920 ± 50 rpm (No

Load)

2950 ± 50 rpm (No

Load)

2950 ± 50 rpm (No

Load)

3220 ± 50 rpm (No

Load)

Low Idle 1300 ± 25 rpm (No

Load)

1100 ± 50 rpm (No

Load)

1300 ± 25 rpm (No

Load)

1000 ± 50 rpm (No

Load)

1050 ± 50 rpm (No

Load)

Rotation Counter-clockwise viewed at flywheel

Fuel #2 Low or ultra-low sulfur Diesel Fuel

Injection Pump Bosch MD type mini pump

Engine Oil (API

Class)

CJ-4 CJ-4 / CK-4

Oil Pan

Capacity

5.5 quart (5.2 l) 7.5 quart (7.1 l) 5.5 quart (5.2 l) 7.5 quart (7.1 l) 5.3 quart (5 l)

Starter 12 Volt, 2 kW 1.2kW

Alternator 12 Volt, 45 Amp

Dry Weight 332.9 lb. (151 kg) 405.7 lb. (184 kg) 408 lb. (185 kg) 487 lb. (221 kg) 341.7 lb. (173 kg)

Dimensions

(Length x Width

x Height)

22.7 x 19.6 x 26.9 in.

(57.6 x 49.9 x 68.4 cm)

26.4 x 19.6 x 26.9 in.

(67.1 x 49.9 x 68.4 cm)

29.3 x 20 x 28.4 in.

(74.4 x 50.7 x 72.1 cm)

34.2 x 20.4 x 28.4 in.

(86.9 x 51.7 x 72.1 cm)

31 x 17.9 x 27.2 in.

(78.7 x 45.5 x 69.1cm)

Emission

Regulation

EPA Tier 4 Interim

EU Stage IIIA

EPA Tier 4 Final/Stage 5

EU Stage IIIB

SPECIFICATIONS 4

en-12

4.2 DIMENSIONS AND WEIGHTS ________________________________________________

LF550 / LF570

A - Width of Cut 100 inch (254.0 cm)

B - Maximum Width 115 inch (292.1 cm)

C - Transport Width 87 inch (220.9 cm)

D - Height ROPS frame in the vertical position 88 inch (223.5 cm)

E - Height ROPS frame folded 61 inch (155.2 cm)

F - Total length cutting with grass catchers 120 inch (304.8 cm)

G - Total length transport 120 inch (304.8 cm)

H - Wheel Base 62 inch (157.5 cm)

J - Front Wheel Track 72 inch (182.9 cm)

K - Rear Wheel Track 43 inch (109.2 cm)

L - Maximum Height Canopy 93 inch (236.2 cm)

Weight of unit, hydraulic and fuel tanks filled,

reels lifted. Tier 4 Interim D1803 Engine

LF550 2WD: 2946 lb. (1336 kg)

LF550 4WD: 3277 lb. (1486 kg)

LF570 2WD: 3036 lb. (1377 kg)

LF570 4WD: 3367 lb. (1527 kg)

Weight of unit, hydraulic and fuel tanks filled,

reels lifted. Tier 4 Final D1803 Engine

LF550 2WD: 3036 lb. (1377 kg)

LF550 4WD: 3367 lb. (1527 kg)

LF570 2WD: 3126 lb. (1418 kg)

LF570 4WD: 3457 lb. (1568 kg)

Weight of unit, hydraulic and fuel tanks filled,

reels lifted. Tier 4 Interim V2403 Engine

LF550 2WD: 3192 lb. (1448 kg)

LF550 4WD: 3523 lb. (1598 kg)

LF570 2WD: 3282 lb. (1489 kg)

LF570 4WD: 3698 lb. (1677 kg)

Weight of unit, hydraulic and fuel tanks filled,

reels lifted. Tier 4 Final & Stage 5 V2403 Engine

LF550 2WD: 3282 lb. (1489 kg)

LF550 4WD: 3613 lb. (1639 kg)

LF570 2WD: 3372 lb. (1530 kg)

LF570 4WD: 3788 lb. (1718 kg)

Weight of fuel in tank 122 lb. (55 kg)

Tire Specifications

Front Wheel Rear Wheel

Tire Size Type Tire Pressure Tire Size Type Tire Pressure

26.5 x 14-12 Ultra Chevron 4 Ply 12 psi (0.83 BAR) 20 x 10-8 Grassmaster 4 Ply 12 psi (0.83 BAR)

4 SPECIFICATIONS

en-13

A (LF550 / LF570)

B (LF550 / LF570)

SPECIFICATIONS 4

en-14

4.3 MOWER SPECIFICATION ___________________________________________________

Battery: 12V, 600 CCA, Group BCI 24

Service Brake: Dynamic braking through the traction circuit

Parking Brake: Integrated in wheel motor, hydraulic release

Fuel Tank: 17 U.S. Gallons (65 l)

Hydraulic Tank: 14 U.S. Gallons (53 l)

Hydraulic Fluid: GreensCare 68

Return Filter: 10 Micron, 30 psi (2.06 BAR) crack bypass

Charge Filter: 10 Micron, 30 psi (2.06 BAR crack bypass

Hydraulic Cooling: Side by side combined hydraulic oil cooler and engine coolant radiator

Steering: Hydrostatic power steering, with adjustable steering wheel

2WD Traction Drive: Parallel system in the forward and reverse direction. Variable displacement hydraulic pump to

24.3 in3 (398 cc) front wheel motors.

4WD Traction Drive: SureTrac™ 4WD parallel-cross-series system in the forward direction. 2WD in the reverse

direction. Variable displacement hydraulic pump to 24.3 in3 (398 cc) front wheel motors and

18.3 in3 (300 cc) rear wheel motors.

LF550 Cutting Unit Drive: 0.72 in3 (11.8 cc) hydraulic motors connected to the cutting unit

LF570 Cutting Unit Drive: 1.01 in3 (16.5 cc) hydraulic motors connected to the cutting unit

Mow Speed: 0-8 mph (0-13 kph)

Transport Speed: 0-12 mph (0-19.3 kph)

Reverse Speed: 0-5 mph (0-8.1 kph)

LF550 / LF570 Cutting Performance: 5.7 acres/hr. (2.32 hectares/hr) @7 mph (11.25 km/hr)

4.4 HYDRAULIC SPECIFICATION ________________________________________________

Circuit Description Flow @2800 rpm engine speed

US Gallons/Minute (Liters/Minute)

Relief Valve Pressure

psi (BAR)

Forward Traction Circuit 34.06 (128.9) 3625 (250)

Reverse Traction Circuit 34.06 (128.9) 3625 (250)

Charge Pressure 6.8 (25.7) 315 (21.7)

Mowers 6.8 (25.7) 1167 (80.5) in Reel Motors

Steering and Lift/Lower 6.8 (25.7) 1450 (100)

4 SPECIFICATIONS

en-15

4.5 VIBRATION LEVEL ________________________________________________________

The mower was tested for hand and arm vibration levels. The operator was in the normal position to drive the vehicle,

with two hands on the steering mechanism. The engine was in operation and the cutting device was in rotation, while

the mower was not moving.

The Machinery Safety Directive 2006/42/EC

By compliance to:

The Lawnmower Standard BS EN ISO 5395-3

Referenced to Hand/Arm: BS EN ISO 20643:2008

Information Supplied for Physical Agents Directive 2002/44/EC

By reference to:

Hand/Arm Standards: BS EN ISO 5349-1 (2001)

BS EN ISO 5349-2 (2001)

The mower was tested for Whole Body vibration levels. The operator was in the normal position to drive the vehicle,

with two hands on the steering mechanism. The cutting device was in rotation with the mower driven in a straight line at

6 Km/hr on a level and cut lawn.

The Machinery Safety Directive 2006/42/EC

By compliance to:

Whole Body EN1032:2003

Information Supplied for Physical Agents Directive 2002/44/EC

By reference to:

Whole Body Standards BS EN ISO 2631-1 (1997)

Hand/Arm

Acceleration Level

Maximum Left Hand or Right Hand Accelerations m/s2

Mean Value of X, Y, Z Aeq

68019 3.44 ± 0.6

Whole Body

Acceleration Level

Maximum Seat Pad Accelerations m/s2

Mean Value of X, Y, Z Aeq

68019 0.42 ± 0.056

SPECIFICATIONS 4

en-16

4.6 SLOPES _________________________________________________________________

DO NOT USE ON SLOPES GREATER THAN 18.3°. The 18.3° slope was calculated with static stability measurements

according to the requirements of BS EN ISO 5395-3.

4.7 CUTTING UNIT SPECIFICATION ______________________________________________

4.8 RECOMMENDED LUBRICANTS ______________________________________________

Engine Oil:

Must meet MIL-L-46152 or API Classification grades CJ-4

Hydraulic Fluid:

The standard hydraulic fluid is GreensCare™ 68.

GreensCare™ 68 Plus and SAE 10W-30 (MIL-L-46152 or API Classification grades SG, SF/CC, CD) are alternative

fluids.

Grease:

Texaco Starplex 2EP Moly (NLGI Grade 2-EP Lithium Complex Grease containing Molybdenum Disulfide) or

equivalent

LF550 / LF570

Blade Length 22 in. (55.9 cm)

Number of cutting units 5

LF550 Height of cut 3/8 to 3/4 in. (0.95 to 1.9 cm)

LF570 Height of cut 3/8 to 1-1/8 in. (0.95 to 2.9 cm

Height of cut adjustment Lift or lower front roller with adjustment knobs on the ends of reel.

Temperature Viscosity

Above 77° F (25° C) SAE 30 or SAE 10W-30 or SAE 10W-40

32° to 77° F (0° to 25° C) SAE 20 or SAE 10W-30 or SAE 10W-40

Below 32° F (0° C) SAE 10W or SAE 10W-30 or SAE 10W-40

NOTICE

Use of SAE 10W-30 oil will compromise all biodegradable properties of the hydraulic system. Flushing the hydraulic

system with GreensCare Bio-Flush will be required to switch back to GreensCare 68 or GreensCare 68 Plus.

4 SPECIFICATIONS

en-17

4.9 ACCESSORIES ___________________________________________________________

4.9.1 LF550/LF570 CUTTING UNITS _______________________________________________

Left Hand 7 Blade Reel 62839 (3 Required)

Right Hand 7 Blade Reel 62840 (2 Required)

Left Hand 9 Blade Reel 62855 (3 Required)

Right Hand 9 Blade Reel 62856 (2 Required)

Left Hand Vertical Mower 67894 (3 Required)

Right Hand Vertical Mower 67895 (2 Required)

4.9.2 LF570/LF570 CUTTING UNITS _______________________________________________

11 Blade Reel 67986 (5 Required)

9 Blade Reel 67987 (5 Required)

Vertical Mower 67854 (5 Required)

4.9.3 22 IN. (55.9 CM) FRONT ROLLERS ___________________________________________

Ø 2 in. (5.1 cm) Grooved Steel Disk 68527

Ø 2 in. (5.1 cm) Light Solid Tube with Scraper 68530

Ø 2 in. (5.1 cm) Heavy Solid Tube with Scraper 68641

Ø 2-3/16 in. (5.5 cm) Grooved Machined Steel 68613

Ø 2-3/16 in. (5.5 cm) Grooved Machined Aluminum 68614

Ø 2-1/4 in. (5.7 cm) Grooved Segmented Aluminum 68673

Ø 3 in. (7.6 cm) Grooved Steel 123268

Scraper for 123268 roller 391202 or 3006263

4.9.4 REAR ROLLERS __________________________________________________________

Ø 2 in. (5.1 cm) 22 in. (55.9 cm) Rear Roller 1004990

Ø 2 in. (5.1 cm) 22 in. (55.9 cm) Rear Roller 1000770

Ø 2-1/2 in. (6.3 cm) 20 in. (50.8 cm) Rear Roller 5003687

Ø 2-1/2 in. (6.3 cm) 22 in. (55.9 cm) Rear Roller 1003728

Ø 2-1/2 in. (6.3 cm) 24 in. (61.0 cm) Rear Roller 1002446

4.9.5 LF550/LF570 REEL ACCESSORIES___________________________________________

Grass Catcher (5 Required) 67891

Powered Rear Roller Brush (5 Required) 62820

RH Turf Groomer 1/4 in. Spacing (2 Required) 67911

LH Turf Groomer 1/4 in. Spacing (3 Required) 67912

RH Turf Groomer 1/2 in. Spacing (2 Required) 67913

LH Turf Groomer 1/2 in. Spacing (3 Required)) 67914

High Height of Cut (1-3/16 in. (3 cm)) Kit 67917

4.9.6 LF550/LF570 REEL ACCESSORIES___________________________________________

Grass Catcher (5 Required) 67891

RH Catcher Mounting Kit (3 Required) 67919

LH Catcher Mounting Kit (2 Required) 67920

Powered Rear Roller Brush (5 Required) 62821

Heavy Duty Rear Roller Scraper 4239802 (Requires 62821)

RH Turf Groomer 1/2 in. Spacing (2 Required) 67989

LH Turf Groomer 1/2 in. Spacing (3 Required) 67988

High Height of Cut (1-9/16 in. (4 cm)) 4113920

Reel/Vertical Mower Lift Yoke 1003361

SPECIFICATIONS 4

en-18

4.9.7 CANOPY / SUN SHADE _____________________________________________________

Product number 68127

4.9.8 HOOD LOCKING LATCH ____________________________________________________

Kit Number 1004049

4.9.9 BALL CAGE ______________________________________________________________

Factory Installed: 4265200

Dealer Installed: 4265199

4.9.10 LED LIGHT KIT ___________________________________________________________

LED Light Kit (One Light) : 4238642

4.10 SUPPORT LITERATURE ____________________________________________________

Contact your Jacobsen Dealer for a complete listing of literature available for your mower.

Safety, Operation, & Maintenance Manual: 4358526

Mower Parts Manual: 4358527

Tier 4 Final / Stage 5 D1803 / V2403 Engine Parts Manual: 4299117

Tier 4 Interim Engine Parts Manual: 4358529

Service & Repair Manual: TBD

5 LABELS

en-19

5Labels

5.1 SAFETY LABELS__________________________________________________________

Understand the purpose of these labels. The labels are important to the safe operation of the mower. REPLACE THE

DAMAGED labels IMMEDIATELY.

DANGER

To prevent injury while you do work on the battery:

1. Connect the negative (BLACK) wire after the positive (RED)

wire. Remove the negative (BLACK) wire before the positive

(RED) wire.

2. Keep sparks and flames away from the battery. Prevent the

contact with the battery acid.

To prevent injury while you attach the jumper cables to the battery:

1. Connect the positive (+) battery terminal of the charged

battery to positive battery terminal of drained battery.

2. Connect the negative (– ) battery terminal of the charged

battery to frame of vehicle with drained battery.

WARNING

The engine coolant is under pressure. To prevent injury, do not remove the

radiator cap on a hot radiator.

WARNING

To prevent injury, do not touch the muffler or

muffler shield. The muffler temperatures can be

more than 150° F (66°C).

WARNING

Always use the seat belt with the ROPS frame in the vertical and

locked position.

Never use the seat belt with the ROPS in the folded position.

4181864

4181862

4199140

Sidan laddas ...

Jacobsen 068019- Maintenance Manual

varumärke: Jacobsen

Modell: 068019-

Kategori: Gräsklippare

Typ: Maintenance Manual

Ladda ner pdf

Rapportera

på andra språk

English: Jacobsen 068019-

Jacobsen 068019- Maintenance Manual

Jacobsen 068019- Maintenance Manual

på andra språk

Relaterade papper

Andra dokument