Silvercrest SDM 1500 C2 Operating Instructions Manual

varumärke: Silvercrest

Modell: SDM 1500 C2

Typ: Operating Instructions Manual

IAN 280641

STEAM MOP SDM 1500 C2

STEAM MOP

Operating instructions

ÅNGMOPP

Bruksanvisning

HÖYRYMOPPI

Käyttöohje

DAMPFMOPP

Bedienungsanleitung

MOP NA PARĘ

Instrukcja obsługi

GB / IE Operating instructions Page 1

FI Käyttöohje Sivu 19

SE Bruksanvisning Sidan 37

PL Instrukcja obsługi Strona 55

DE / AT / CH Bedienungsanleitung Seite 73

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Käännä ennen lukemista kuvallinen sivu esiin ja tutustu seuraavaksi laitteen kaikkiin toimintoihin.

Vik ut bildsidan och ha den till hands när du läser igenom anvisningarna och gör dig bekant med

apparatens / maskinens funktioner.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi

funkcjami urządzenia.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

│

1 ■

SDM 1500 C2

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Information concerning these operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . 2

Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Operating components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Unpacking and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Package contents and transport inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Disposal of packaging materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Assembling the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Handling and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Filling with water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

After use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Maintenance/changing the ﬁ lter . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Kompernass Handels GmbH warranty . . . . . . . . . . . . . . . . . . . . . . .15

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Ordering spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

■ 2

│

SDM 1500 C2

Introduction

Information concerning these operating instructions

Congratulations on the purchase of your new appliance.

You have selected a high-quality product. The operating instructions are part of

this product. They contain important information on safety, usage and disposal.

Before using the product, familiarise yourself with all operating and safety instructions.

Use the product only as described and for the speciﬁ ed areas of application.

Please also pass on these operating instructions to any future owner.

This documentation is protected by copyright.

Any copying or reproduction, including in the form of extracts, or any reproduction

of images (even in a modiﬁ ed state), is permitted only with the written authorisation

of the manufacturer.

Intended use

This appliance is intended exclusively for cleaning indoor ﬂ oors. The appliance is

not intended for any other purpose, nor for use beyond the scope described. The

appliance is not intended for use in commercial or industrial environments.

The manufacturer accepts no responsibility for damage caused by failure to observe

these instructions, improper use or repairs, unauthorised modiﬁ cations or the use

of unapproved replacement parts. The operator bears sole liability.

│

3 ■

SDM 1500 C2

Safety instructions

RISK OF ELECTRIC SHOCK!

► Connect the appliance only to mains power sockets supplying

a mains power voltage of 220 - 240 V

, 50/60 Hz.

► In the event of operating malfunctions, and before cleaning

the appliance, disconnect the plug from the mains power

socket.

► To disconnect the power cable, always pull the plug from the

socket, do not pull the power cable itself.

► Do not kink or crush the power cable, and route the cable

so that it cannot be stepped on or tripped over.

► To avoid risks, arrange for defective plugs and/or power

cables to be replaced at once by qualiﬁ ed technicians or

our Customer Service Department.

► Make sure that the power cable does not become wet or

damp during use. Route the cable in such a way that it

cannot be crushed or damaged.

► To prevent risks, stop using the appliance immediately if it

is damaged.

► Disconnect the appliance from the mains power socket before

ﬁ lling it with water, changing accessories or cleaning it.

Use the appliance only in dry indoor areas, not

outdoors.

► Never submerse the appliance in water or other liquids!

► Never aim the steam jet directly at electrical appliances or

equipment which contains electrical components, such as

the interior of ovens.

■ 4

│

SDM 1500 C2

RISK OF ELECTRIC SHOCK!

► Operate the appliance only with dry hands and never without

shoes (i.e. not barefoot). This will help reduce the eﬀ ect of

an electric shock in the event of a malfunction.

► Never aim the appliance at moisture-sensitive objects.

► This appliance may be used by persons with limited physical,

sensory or mental capabilities or lack of experience and

knowledge, provided that they are under supervision or have

been told how to use the appliance safely and are aware of

the potential risks. Children must not use the appliance as a

plaything. Cleaning and user maintenance tasks may not be

carried out by children unless they are supervised.

WARNING! RISK OF INJURY!

► Some parts of the appliance may become hot during use!

There is a risk of scalding!

► Allow the accessories used to cool down before dismantling

them.

► Use only the original accessory parts for this appliance.

Other accessories may not meet the safety requirements.

► The appliance may not be used if it has been dropped, if there

are any obvious signs of physical damage or if it is leaking.

► The appliance must be kept out of the reach of children if it

is switched on or is cooling down.

► Never direct the steam at people or animals. Hot steam can

cause serious injuries!

► Always pull the plug out of the power socket during each

break in use, as well as after use and before any cleaning.

│

5 ■

SDM 1500 C2

RISK OF BURNS!

Caution! Hot surface!

This symbol warns you about escaping steam.

Please follow the safety instructions!

CAUTION! MATERIAL DAMAGE!

► Use the appliance only on ﬂ oors made of marble, stone, tile,

parquet ﬂ ooring or hardwood that have been treated and

are impervious to water.

► Never use the appliance ...

– ... on untreated or permeable ﬂ oors,

– ... on glass surfaces,

– ... on soft plastic surfaces,

– ... on ﬂ oors that have been treated with wax,

– ... on carpets with wool content.

► Always comply with the cleaning instructions of the carpet

manufacturer. Before cleaning, check also whether the car-

pet is suitable for steam cleaning. Use the appliance only

on parquet ﬂ oors if they have been hard-sealed.

► Do not leave the appliance standing on wooden ﬂ oors for

any length of time while it is switched on. This might cause

the wood to swell.

► Do not operate the appliance with an empty water tank.

Otherwise, the pump could run dry and overheat.

► Do not use an external timer switch or a separate remote

control system to operate the appliance.

► Never leave the appliance unattended during operation.

► Do not use the appliance outdoors.

■ 6

│

SDM 1500 C2

CAUTION! MATERIAL DAMAGE!

► Ensure that the appliance, the power cable and the plug do

not come into contact with heat sources such as hotplates or

naked ﬂ ames.

Operating components

Figure A:

1 “Handle” release button

2 Carrying handle

3 Main unit

4 Connection nozzle

5 Steam foot

6 Pad

7 Filter

8 Water tank

9 “Water tank” release button

0 POWER control lamp

q Red control lamp “high steam level”

w Green control lamp “low steam level”

e MODE button

r “Steam” button

Figure B:

t Notch

z Upper cable hook

u On/oﬀ switch

i Lower cable hook

Figure C:

o Replacement pad

p Carpet ring

a Carpet ring release aid

│

7 ■

SDM 1500 C2

Unpacking and installation

Safety instructions

WARNING

During the ﬁ rst use of the appliance there is a risk

of injury and/or damage to property!

To avoid risks, observe the following safety instructions:

► Do not allow children to play with packaging materials.

There is a risk of suﬀ ocation.

Package contents and transport inspection

The appliance is supplied with the following components as standard (see fold-

out page):

● Main unit

● Steam foot

● Carpet cleaning ring

● 2 pads

● Operating instructions

NOTE

►

Check the package for completeness and for signs of visible damage.

► If the delivery is incomplete or damage has occurred as a result of defec-

tive packaging or during transport, contact the service hotline (see section

Service).

Unpacking

♦ Remove all parts of the appliance and the operating instructions from the box.

♦ Remove all packaging materials and any ﬁ lms and labels.

■ 8

│

SDM 1500 C2

Disposal of packaging materials

The packaging protects the appliance from damage during transport. The packaging

materials have been selected for their environmental friendliness and ease of

disposal, and are therefore recyclable.

Returning the packaging into the material cycle conserves raw materials and

reduces the amount of waste generated. Dispose of packaging materials that

are no longer needed in accordance with applicable local regulations.

NOTE

►

If possible, keep the appliance's original packaging during the warranty

period so that the appliance can be packed properly for return shipment

in the event of a warranty claim.

Assembling the appliance

♦ Push the main unit 3 onto the connection nozzle 4 on the steam foot 5 and

press the main unit 3 down until the round catch clicks into place.

♦ Attach a pad 6 from below onto the steam foot 5.

NOTE

►

If you intend to clean carpeting with the steam mop, ﬁ t the steam foot 5

onto the carpet ring p. Ensure that the carpet ring unlocking aid a is in

line with the connection nozzle 4. Push the steam foot 5 onto the carpet

ring p so that it clicks audibly into place. This will allow the pad 6 to

glide over the carpet.

► To remove the carpet ring p, press your foot onto the carpet ring release

aid a and pull the steam foot 5 carefully oﬀ the carpet ring p.

Handling and operation

This section provides you with important information on handling and using the

appliance.

Filling with water

CAUTION – PROPERTY DAMAGE!

►

Never operate the appliance without water in the water tank 8!

The pump could overheat and be damaged!

1) Push the “Water tank” release button 9 downwards and simultaneously

pull the water tank 8 towards the rear and oﬀ the appliance with a tilt

movement.

2) Turn the water tank 8 and unscrew the cap.

3) Fill the water tank 8 with tap water up to the MAX mark.

│

9 ■

SDM 1500 C2

NOTE

If the mains water in your location is rated as hard, it is recommended that

you mix the mains water with some distilled water. Otherwise, the jets for

the steam blast function could calcify (become blocked) prematurely.

To extend the optimal steam blast function, mix mains water with

distilled water according to the table:

Water hardness Ratio of distilled

water to

tap water

very soft/soft 0

medium 1:1

hard 2:1

very hard 3:1

The water hardness level can be queried at your local water works.

4) Attach and hand-tighten the clamp.

5) Turn the water tank 8 around again and place it back onto the main unit 3:

First ﬁ t the lower part into the main unit 3 and then ﬂ ip the top part into the

device. Push it ﬁ rmly into place so that the water tank 8 audibly clicks into

place and sits ﬁ rmly on the main unit 3.

Operation

CAUTION – PROPERTY DAMAGE!

►

If you are not sure whether the ﬂ oor is suitable for cleaning, please carry

out a tolerance test using a concealed part of the ﬂ oor.

► Always comply with the cleaning instructions of the carpet manufacturer.

Before cleaning, check also whether the carpet is suitable for steam clean-

ing.

► Never use the appliance without a pad 6 on the steam foot 5.

Otherwise the ﬂ oor could get scratched!

► Never operate the appliance without water in the water tank 8!

The pump could overheat and be damaged!

NOTE

►

Before you clean the ﬂ oor with the steam mop, we recommend that you

vacuum the ﬂ oor to remove any loose particles of dirt.

Once the appliance is assembled and ﬁ lled with water:

1) Press and hold in the “Handle” release button 1 and ﬂ ip the handle up-

wards so that it clicks into place.

■ 10

│

SDM 1500 C2

2) If not already done: Completely unwind the power cable from the cable

hooks z/i. To facilitate the unwinding of the cable, you can ﬂ ip down the

upper cable hook z by pulling it out a little and turning it at the same time.

3) Run the cable through the notch t on the rear of the handle so that the

cable does not hang down into the working area.

4) Insert the plug into the mains power socket.

5) Set the on/oﬀ switch u to “I”. The on/oﬀ switch u lights up, the red

POWER control lamp 0 ﬂ ashes.

6) Use the MODE button e to select the desired level of steam generation:

– Press 1 x: low steam level, green control lamp w lights up.

– Press 2 x: high steam level, red control lamp q lights up.

– Press 3 x: no steam, standby, POWER control lamp 0 lights up.

NOTE

►

We recommend the high steam level especially for moisture- and heat-

resistant ﬂ oor coverings, such as tiles.

► We recommend the low steam level especially for moisture- and heat-

sensitive ﬂ oor coverings, such as parquet ﬂ ooring.

7) Wait around 30 seconds while the appliance heats up.

8) Press the “Steam” button r. The appliance starts generating steam and,

after a short time, steam is emitted through the pad 6.

9) Wipe over the desired area.

If the water tank 8 becomes empty during use:

NOTE

►

Once the water tank 8 has been pumped empty, the pump will continue

running a little while until the empty water tank 8 is indicated by the simul-

taneous ﬂ ashing of the red control lamp “high steam level” q, the green

control lamp “low steam level” w and POWER control lamp 0.

– Press the “Steam” button r again to stop steam production.

– Set the on/oﬀ switch u to “O”.

– Remove the water tank 8, ﬁ ll it and replace the water tank 8 as

described in the section “Filling with water”.

– Set the on/oﬀ switch u to “I”.

– Select the desired steam level as described above and press the

“Steam” button r.

│

11 ■

SDM 1500 C2

10) When you are ﬁ nished treating all of the surfaces, press the “Steam”

button r to stop steam production.

11) Set the on/oﬀ switch u to “O”. The POWER control lamp 0 goes out.

12) Remove the power plug from the mains power socket.

NOTE

►

If you see streaks on the ﬂ oor after cleaning with the appliance, this may

be due to the previously used cleaning ﬂ uids. Simply clean the ﬂ oor again

using the steam mop. The smears should now be gone.

After use

1) Allow the appliance to cool down.

2) Remove the pad 6.

3) Remove the water tank 8 from the appliance and empty it.

4) Pull the upper cable hook z out a little and turn it back upwards.

Wind the cable back around the two cable hooks z/i.

Fix the end of the power cable using the cable clip located on the cable.

Cleaning and care

RISK OF ELECTRIC SHOCK!

►

Always remove the mains power plug before cleaning the appliance!

WARNING – RISK OF INJURY!

► Allow the appliance to cool down before cleaning it. Risk of burns!

CAUTION – PROPERTY DAMAGE

►

When cleaning the surfaces use neither abrasive or chemical cleaners,

nor sharp or scratchy objects.

■ Empty the water tank 8 after every use.

■ After each use, remove the pad 6 from the steam foot 5 and wash it out.

■ 12

│

SDM 1500 C2

■ Note the following washing instructions when you wash the pad 6 in the

washing machine:

Wash at max. 60°C

Do not tumble dry

Do not iron

■ If necessary, wipe the appliance with a damp cloth. For stubborn soiling use

a mild detergent on the cloth.

Maintenance/changing the ﬁ lter

After 4–6 months or approximately 100 cleaning cycles (one cycle corresponds

to one water tank ﬁ lling), you will need to change the ﬁ lter 7. Please contact

our Service Department for replacement ﬁ lters.

RISK OF ELECTRIC SHOCK!

►

Before changing the ﬁ lter 7, always pull out the mains plug!

1) To remove the ﬁ lter 7, ﬁ rst remove the water tank 8 from the appliance.

2) Pull the ﬁ lter 7 upwards out of the appliance.

3) Insert the new ﬁ lter 7.

4) Replace the water tank 8.

│

13 ■

SDM 1500 C2

Troubleshooting

Programme Possible causes Possible solutions

The appliance is

not working.

The plug is not connected.

Connect the appliance to a

mains power socket.

The appliance

produces no steam.

The "Steam" button r has

not been pressed.

Press the "Steam" button r.

There is no water in the

water tank 8.

Fill the water tank 8 with

tap water.

The ﬁ lter 7 is blocked. Change the ﬁ lter 7.

No steam setting has

been selected.

Use the MODE button e to

select the desired level of steam.

The pump makes

unusually loud

noises.

There is no water in the

water tank 8.

Fill the water tank 8 with

tap water.

A whitish edge

forms on the ﬂ oor

when the appliance

stops brieﬂ y during

operation.

Lime has collected.

Wipe the limescale away with a

damp cloth. If necessary, add a

little descaler onto the cloth.

■ 14

│

SDM 1500 C2

Storage

■ Fold the handle by pressing the “Handle” release button 1.

■ Pull the upper cable hook z out a little and turn it back upwards.

Wind the cable back around the two cable hooks z/i.

■ Carry the appliance using the carrying handle 2.

■ Store the appliance in a dry and dust-free location.

Disposal

Do not dispose of the appliance in your normal domestic waste.

This product is subject to the provisions of European Directive

2012/19/EU-WEEE (Waste Electrical and Electronic Equipment).

Dispose of the appliance via an approved waste disposal company or your

municipal waste disposal facility. Please comply with all applicable regulations.

Please contact your waste disposal facility if you are in any doubt.

Appendix

Technical data

Voltage supply 220 - 240 V

(AC) | 50 / 60 Hz

Power consumption 1370 - 1630 W

Protection rating

IPX4

Protected against water splashes

from any direction.

Information on the pads 6/o

Material composition 100% polyester

Wash at max. 60°C

Do not tumble dry

Do not iron

│

15 ■

SDM 1500 C2

Kompernass Handels GmbH warranty

Dear Customer,

This appliance has a 3-year warranty valid from the date of purchase. If this product

has any faults, you, the buyer, have certain statutory rights. Your statutory rights

are not restricted in any way by the warranty described below.

Warranty conditions

The validity period of the warranty starts from the date of purchase. Please keep

your original receipt in a safe place. This document will be required as proof of

purchase.

If any material or production fault occurs within three years of the date of purchase

of the product, we will either repair or replace the product for you at our discretion.

This warranty service is dependent on you presenting the defective appliance

and the proof of purchase (receipt) and a short written description of the fault

and its time of occurrence.

If the defect is covered by the warranty, your product will either be repaired or

replaced by us. The repair or replacement of a product does not signify the begin-

ning of a new warranty period.

Warranty period and statutory claims for defects

The warranty period is not prolonged by repairs eﬀ ected under the warranty.

This also applies to replaced and repaired components. Any damage and defects

present at the time of purchase must be reported immediately after unpacking.

Repairs carried out after expiry of the warranty period shall be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accordance with strict quality guidelines

and inspected meticulously prior to delivery.

The warranty covers material faults or production faults. The warranty does not

extend to product parts subject to normal wear and tear or fragile parts such as

switches, batteries, baking moulds or parts made of glass.

The warranty does not apply if the product has been damaged, improperly used

or improperly maintained. The directions in the operating instructions for the product

regarding proper use of the product are to be strictly followed. Uses and actions

that are discouraged in the operating instructions or which are warned against

must be avoided.

This product is intended solely for private use and not for commercial purposes.

The warranty shall be deemed void in cases of misuse or improper handling, use

of force and modiﬁ cations / repairs which have not been carried out by one of

our authorised Service centres.

■ 16

│

SDM 1500 C2

Warranty claim procedure

To ensure quick processing of your case, please observe the following instructions:

■ Please have the till receipt and the item number (e.g. IAN 12345) available

as proof of purchase.

■ You will ﬁ nd the item number on the type plate, an engraving on the front

page of the instructions (bottom left), or as a sticker on the rear or bottom of

the appliance.

■ If functional or other defects occur, please contact the service department

listed either by telephone or by e-mail.

■ You can return a defective product to us free of charge to the service address

that will be provided to you. Ensure that you enclose the proof of purchase

(till receipt) and information about what the defect is and when it occurred.

You can download these instructions along with many other manuals,

product videos and software on www.lidl-service.com.

Service

Service Great Britain

Tel.: 0871 5000 720 (£ 0.10/Min.)

E-Mail: k[email protected]

IAN 280641

Importer

Please note that the following address is not the service address. Please use the

service address provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

│

17 ■

SDM 1500 C2

Ordering spare parts

You can order the following replacement parts for product SDM 1500 C2:

► 2 x Replacement pad ► 1 x Filter

Order the replacement parts via the Service Hotline (see section „Service“) or

simply visit our website at www.kompernass.com.

NOTE

►

Have the IAN number of the appliance ready (can be found on the cover

of these operating instructions) when you place your order.

Sidan laddas ...

Silvercrest SDM 1500 C2 Operating Instructions Manual

varumärke: Silvercrest

Modell: SDM 1500 C2

Typ: Operating Instructions Manual

Ladda ner pdf

Rapportera

Silvercrest SDM 1500 C2 Operating Instructions Manual

Silvercrest SDM 1500 C2 Operating Instructions Manual

på andra språk

Relaterade papper

Andra dokument