POINT 3-SERIES POIH3060C4E4 KERAMISK TOPP Bruksanvisning

POIH3060C4E4

User Manual

Ceramic Hob

Thank you for purchasing your new POINT Ceramic Hob.

These operating instructions will help you use it properly and safely.

We recommend that you spend some time reading this instruction

manual in order to fully understand all the operational features it

offers. Read all the safety instructions carefully before use and keep

this instruction manual for future reference.

GB

NO

Takk for at du kjøpte ditt nye POINT Keramisk platetopp.

Denne bruksanvisningen vil hjelpe deg med å bruke den på en trygg og

riktig måte. Vi anbefaler at du tar deg tid til å lese gjennom hele

bruksanvisningen for å bli fortrolig med alle funksjonene som tilbys.

Les alle sikkerhetsanvisningene nøye før bruk, og oppbevar

bruksanvisningen for fremtidig referanse.

FI

Kiitos, kun valitsit uuden POINT keraamisen keittotason.

Nämä käyttöohjeet opastavat sinua käyttämään laitetta oikein ja

turvallisesti. On suositeltavaa käyttää aikaa tämän käyttöoppaan

lukemiseen, jotta ymmärrät täysin, mitä toiminnallisia ominaisuuksia

tuote tarjoaa. Lue kaikki turvallisuusohjeet huolellisesti ennen laitteen

käyttöä ja säilytä käyttöopas myöhempää käyttöä varten.

DK

Tak for købet af dit nye Keramisk kogeplade fra POINT.

Disse brugervejledninger hjælper dig med at bruge dette apparat rigtigt og

sikkert. Vi anbefaler, at du læser denne brugervejledning, så du får en fuld

forståelse af hvordan alle funktionerne virker. Læs sikkerhedsforskrifterne

grundigt inden brug, og gem denne brugervejledning til senere brug.

SE

Tack för att du har köpt ditt nya Keramikhäll från POINT.

Denna bruksanvisning hjälper dig att använda den på ett säkert och

korrekt sätt. Vi rekommenderar att du tar dig tid att läsa igenom denna

bruksanvisning för att till fullo förstå alla driftfunktioner som den

erbjuder. Läs noga igenom alla säkerhetsinstruktioner före användning

och spara bruksanvisningen för framtida bruk.

2

Bruksanvisning – Svenska ......................................... sida 76 - 93

Bruksanvisning – Norsk ..............................................side 23 - 40

Instruction Manual – English ................................... page 4 - 22

Brugervejledning – Dansk ...........................................side 59 - 75

Käyttöopas - Suomi ....................................................sivu 41 - 58

3

Safety instructions

This User Instruction Manual contains important information, including safety &

installationpoints, whichwillenable you to get themostout of your appliance. Please

keep it in a safe place so that it is easily available for future reference f

not familiar with the operation of the appliance.

Caution!

Do not use the ceramic hob until you have

read this instruction manual. The ceramic

hob is intended for household use only.

The appliance becomes hot during

operation. Take care not to touch the hot

surface.

Always keep children away from the

ceramic hob.

While in operation direct contact with the

ceramic hob may causeburns!

Ensure that small items of household

equipment, including connection leads, do

not touch the hob as the insulation

material of this equipment is usually not

resistant to high temperatures.

Do not leave the ceramic hob unattended

when frying. Oils and fats may catch ﬁre

due to overheating or boiling over.

Do not switch on the hob until a pan has

beenplaced on it.

Do not put pans weighing over 25kg on

the hob.

Do not use the ceramic hob in the event

of a technical fault. Any faults must be

ﬁxed by an appropriately qualiﬁed and

authorized person.

In the event of any incident caused by a

technical fault, disconnect the power and

report the fault to the service centre to be

repaired.

The rules and provisions contained in this

instruction manual should be strictly

observed. Do not allow anybody who is

not familiar with the contents of this

instruction manual to operate the ceramic

hob.

The ceramic hob shouldnot be cleaned

IMPORTANT: The adjacent furniture or

housing and all materials used in the

installation must be able to withstand a

minimum temperature of 95°C above the

ambient temperature of the room it is

located in, whilst in use.

Any damage caused by the appliance

being installed in contravention of this

temperature limit, or by placing adjacent

cabinet materials closer than 4mm to the

appliance, will be the liability of the owner.

This appliance complies with all current

European safety legislation. We do wish

to emphasize that this compliance does

not remove the fact that the appliance

surfaces will become hot during use and

retain heat after operation.

Child Safety

We strongly recommend that babies

and young children are prevented from

being near the appliance and not

allowed to touch the appliance at any

time.

If it is necessary for youngerfamily

members to be in the kitchen, please

ensure that they are kept under close

supervision at all times.

4

by steam cleaning equipment

General Safety

This appliance is not intended for use

by persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experienceand

knowledge, unless they have been

given supervision or instruction

concerning use of the appliance by a

personresponsible for their safety.

Children should be supervised to

ensure that they do not play with the

appliance.

NEVER try to extinguish a ﬁre with

water, but switch o the appliance and

then cover ﬂame e.g. with a lid or a ﬁre

blanket.

WARNING: Danger of ﬁre: do not store

items on the cooking surfaces.

Means for disconnection must be

incorporated in the ﬁxed wiring in

accordance with the wiring rules.

Do not allow electricalﬁttings or

cables to come into contact with areas

on the appliance that get hot.

Do not use the appliance to heat the

room it is located in or to dry clothing.

Do not install the appliance next to

curtains or soft furnishings.

If the supply cord is damaged, it must

be replaced by the manufacturer, its

service agent or similarly qualiﬁed

persons in order to avoid a hazard.

The appliance is not intended to be

operated by means of an external

timer or separate remote-control

system.

Power cord should not be accessible

after installation.

This product cannot be worked

through outside timer and remote

control.

Warning: If the surface is cracked,

switch o the appliance to avoid the

possibility of electricshock,for hob

surfaces of glass ceramic or similar

material which protect live parts.

Warning: a steam cleaner is not

used.

CAUTION:The cooking processhas to

be supervised. A short term cooking

process has to be supervised

continuously.

WARNING: Unattended cooking on a

hob with fat or oil can be dangerous

and may result in a ﬁre.

This appliance should be connected to

a circuit which incorporates an

isolating switch whichis accessible

the user after installation providing

full disconnection from the power

supply. The disconnection may be

achieved by incorporating a switch in

the ﬁxed wiring in accordance with the

wiring rules.

Warning: Before obtaining access to

terminals, all supply circuits must be

disconnected.

WARNING: Use onlyhob guards

designed by the manufacturer of the

cooking appliance or indicated by the

manufacturer of the appliance in the

instructions for use as suitable or hob

guards incorporated in the appliance.

The use of inappropriate guards can

cause accidents.

WARNING: The appliance and its

accessible parts become hot during use.

Care should be taken to avoid touching

heating elements.

Regarding the instructions for how to

“Installation

5

install, kindly refer to the section

Installation

Electrical connection

Before connecting the appliance, make sure that the supply voltage marked on the Rating

Plate corresponds with your mains supply voltage.

WARNING: THIS APPLIANCE MUST BE EARTHED.

If you have to change the power cord, the earthing (yellow/green) conductor must

always be 10 mm longer than the line conductors.

Care must be taken to ensure that the temperature of the mains supply cable does not

exceed 50°C.

If the mains supply cable is damaged, then it must be replaced by an appropriate

replacement which can be obtained from Spares Department.

Installation of ceramic hob :

6

Preparing the unit forabuilt-in appliance

WARNING

The kitchen units that are in direct contact with the appliances must be heat-proof (min.

95°).

The appliance can be installed on a work surface with a thickness of between 30 and 40

mm and near to walls which are higher than the work surface, maintaining a minimum

distance of 100mm.

Carry out all cutting of the unit and work surface then carefully remove shavings or

sawdust before inserting the appliances.

To ensure correct ventilation of the hob, please comply with the dimensions shown in

ﬁgures

Always refer to the manufacturer for speciﬁc instructions

Make sure the surface is level and square and that no part interferes with the space

required for installation.

Prepare the cut as indicated (see installation dimensions).

Installing the hob

WARNING

Risk of cutting.

Be careful of cutting edges.

End parts in foamed plastic - be careful.

During transportation these could cause slight injury or cuts.

Remove the material and envelope of documents from the packaging.

Before proceeding with installation read the work instructions carefully.

rear of cabinet or

rear wall under

countertop

back edge

of cutout

Fig. 5

A. 40mm min

B. 40mm max

7

Step.1

Put a towel or cloth on the work surface. Place the hob face down

on the protected surface.

Step.2

Apply the strip seal, supplied with the hob, which is for sealing it

onto the work surface.

Do not use silicone. Apply the seal to the edge of the bottom of

the hob, leaving about 3mm from the edge of the glass.

Apply the seal all around the circumference.

Cut any excess and bring the two ends of the seal together so

they match.

Step.3

Fix the brackets (4 pcs) on the front side and rear side by screw. Put the hob in the cut-out

cabinet, and make it centered. Ensure that the front edge of the hob is parallel to the side edge

of the work surface.

IMPORTANT: You mustobserve theventilation

requirements shown in the drawing opposite.

IMPORTANT: There are ventilation holes around the

outside of the hob. YOU MUST ensure that these holes are

not blocked by the work top, when you put the hob into

position (see drawing opposite).

IMPORTANT: Do not use a silicon sealant to seal the

appliance against the aperture. This will make it dicult to

remove the hob from the aperture in future, particularly if it

needs to be serviced.

Carefully turn the hob back over and then gently lower it into the aperture hole that you

have cut out.

Fitting guidelines

The ceramic hob is manufactured to work with two-phase

alternating current (400V 2N~50Hz). The voltage rating of the

ceramic hob heating elements is 230V. Adapting the ceramic hob

to operate with one-phase current is possible by appropriate

Bottom of hob

Glass

surface Cloth

Seal

Self-adhesive

seal

8

bridging in the connection box according to the connection diagram below. The connection

diagram is also found on the cover of the connection box. Remember that the connection wire

should match the connection type and the power rating of the ceramic hob.

The connection cablemust be secured in a strain-relief clamp.

Warning!

Remember to connect the safety circuit to the connection box terminal marked with . The

electricity supply for the ceramic hob must have a safety switch which enables the power to be

cut o in case of emergency. The distance between the working contacts of the safety switch

must be at least 3mm.

Before connecting the ceramic hob to the power supply it is important to read the information

on the data plate and the connection diagram.

The cable connections must be in accordance with the diagram located on the bottom of

the hob.

The cable type must be connected to the corresponding power supply terminal box.

You should use a good quality screwdriver to carefully, fully tighten ALL of the terminal

screws.

If when the hob is ﬁrst switched on, only two of the zones work, you should recheck that

the terminal screws are all fully tightened. This should be done before contacting the

Customer Care Department.

IMPORTANT: The appliance must NOT be connected to the mains supply by means of a

13A plug and socket.

This appliance must be wired into a 30 A double pole switched fused spur outlet, having 3

mm contact separation and placed in an easily accessible position adjacent to the

appliance. It should not be located above the appliance and no more than 1.25m away

fromit.

The cable can be looped if necessary, but make sure that it is not kinked or trapped when

the hob is in position. Care must be taken to avoid the cable being in contact with hot

parts of the appliance.

Replacing the mains supply cable

If the mains supply cable is damaged, then it must be replaced by an appropriate

replacement.

The mains supply cable should be replaced in accordance with the following instructions:

Switch the appliance o at the control switch.

Open the terminal block on the underside of the hob.

9

Unscrew the terminal screws ﬁxing the cable.

The “green-yellow” earth wire must be connected to the terminal marked . It must

be about 10 mm longer than the live and neutral wires.

The “blue” neutral wire must be connected to the terminal marked with letter (N) - the

live wire (L1) must be connected to the terminal marked with letter (L1) (220-240V

1N ).

The “blue” neutral wire must be connected to the terminal marked with letter (N) - the

live wire L1 must be connected to the terminal marked with letter (L1),

must be connected to the terminal marked with letter (L2) (380-420V 2N ).

Description of the Ceramic hob surface layout

4 zone ceramic hob schematic diagram

Control panel layout

1. Button and Display mode

10

1.1.1 Button icon instruction

Icons Function IconsFunction

M1 NO.1 cooking zone select

button

M6 Child safety lock button: press

and hold to lock or unlock the

control panel

M2 NO.2 cooking zone select

button

M7 Timer selector: timing for each

cooking zone

M3 NO.3 cooking zone select

button

M8 Minus button: for reducing time

and powerlevel

M4 NO.4 cooking zone select

button

M9 Power button: press and hold to

turn on or o the hob

M5 Plus button: for adding time

and powerlevel

1.1.2 Display section

2.1 Display mode

1) Single-digit digital indicator: Displays corresponding parameters of the heating control, and

High temperature warning sign (“ ”) of the cooking zone.

2) Two-digit digital indicator: Displays the corresponding parameters of the time and child

safety lock sign.

Icons Function

1 NO.1 Digital cooking zone indicator: displays the power level, high

temperature warning symbol etc.

2 NO.2 Digital cooking zone indicator: displays the power level, high

temperature warning symbol etc.

3 NO.3 Digital cooking zone indicator: displays the power level, high

temperature warning symbol etc.

4 NO.4 Digital cooking zone indicator: displays the power level, high

temperature warning symbol etc.

5 Digital timer indicator: displays the time, child safety lock symbol etc.

11

Using the ceramic hob

Before ﬁrst use

IMPORTANT: You should clean the ceramic hob surface (see “Maintenance and

cleaning” section).

You should switch on one cooking zone at a time, for 5 minutes at the maximum setting.

This will help to eliminate any new smell that exists and evaporate any humidity that has

formed on the heating elements during transit.

Do not heat more than one zone at once.

Youmust place a saucepanﬁlled half full with coldwater on each zone as you heat it.

Operation instruction

1. Power on

After switching on the appliance, the hob will beep once to remind that power is on, all of

the digital indicators on the display screen will light up for 2s, then the appliance goes into

shutdown mode. Note: If the zone is multi-ring, the corresponding digital indicator

decimal point “ ” will light up. If the zone has a single ring only, the digital decimal point

“ ” will not light up.

Shutdown status: All the display will close except the high temperature warning symbol

“ ”; At this time, only the power button “ ” can be operated by pressing and holding, and

other button operations are invalid.

2. Standby mode

Under shutdown status, press and hold “ ” button for 3s, the hob will beep once and

then enter standby mode.

All the digital indicators of the cooking zone will display “ ”(The symbol “ ” will

show in the cooking zone indicator if there is residual heat), timer place will show “ ”

as well, it will not heat at this time.

Under standby mode, if there is no cooking zone heating operation, the appliance will go

into shutdown status automatically after 10s and beep once.

3. Heating control

Under standby mode, you can choose the cooking zone by pressing the cooking zone

select button, then press plus or minus button to adjust the power level of the

corresponding cooking zone. Pressing and holding plus“ ”or minus“ ” buttons can

continuously increase or decrease the power level.

When the hob top is in heating status, press and hold “ ” power button for 3s to switch

o and stop all the cooking zones from heating. The corresponding cooking zone indicator

of the hob top which has heated before will display high temperature warning symbol “ ”.

Under standby mode, if some hob zones still have residual heat, display will show “ ”.

If you need to switch o one of the cooking zones, you can select that zone ﬁrst, then

press the minus button “ ” until “0” power level to switch o that zone, without

aecting the heating of the other cooking zones. When power level reaches “0”, the

12

corresponding cooking zone indicator of the hob top which has heatedbeforewilldisplay

high temperature warning symbol “ ”.

If more than one zone is operating at the same time, total power will be equal to the sum

of the powers of all the working cooking zones, each cooking zone will work according

to their power modulation ratio, and will not aect each other.

Note: 1. During the same period, only one hob top button is valid, that is only one decimal

point “ ” can be displayed.

2. Press minus button “ ”to set the power level to “0”, then the heating hob top will

switch o automatically.

4. Multiple-ring heating function

4.1 Start double ring heating function: The outer ring can only start after the inner ring is

switched on.

1) Press the cooking zone select button which needs to heat, corresponding cooking zone

digital decimal point “ ” will display.

2) Press plus or minus button to select the power level you need.

3) Re-touch the cooking zone select button, cooking zone digital indicator will display single-

ring “ ”. Then press the cooking zone select button again to switch on the outer ring. After

the outer ring is switched on, cooking zone digital indicator will display double-ring “ ”.

4.2 Stop multiple-ring heating function

1) Touch the cooking zone select button which needs to heat, corresponding hob top digital

indicator decimal point “ ” will display.

2) Touch the cooking zone select button to switch o the outer ring, the inner ring continues

to work.

5. Power level adjustment

Under the standby mode, press cooking zone select button to choose the corresponding

cooking zone, corresponding cooking zone digital indicator decimal point “ ” and heating

level will display. You can press the plus “ ”and minus “ ” buttons to adjust suitable

power level.

By holding down either of these buttons, the value on the zone indicator will adjust up or

down. Each pressing of the “ ” button adds one to the power level, until level 9, and

is displayed on its corresponding digital indicator. Each pressing of the “ ” button reduces

power level by one, until level 0 (Each pressing of “+” or “-” button, a short audible

signal will be heard). Keep pressing “ ” or“ ” buttonsto continuously increase or

decrease eect.

Upon completion of power level adjustment, the decimal point “ ”of digital indicator will

stop ﬂashing and normally display the power level within 10 seconds of no operation.

When switching any cooking zone power level to 0, it will stop the power output of

that cooking zone.

If a cooking zone has been heated but power levels of all the cooking zones are “0”, the

appliance will automatically enter into shutdown status after 1 minute of no operation.

6. Auto-heating function

13

Your hob can auto-heat following the steps below:

6.1 Turn on automatic heating: Press plus or minus button to set the power to level 9, then

touch plus button “ ” to let the power level alternately display “ ” and “ ”. At this time,

press minus button“ ” to adjust the auto-heating level you need, such as level 6. In this

automatic heating process, the corresponding digital power level indicator alternately

displays “ ” and “ ”. Alternate display time is 2.5 minutes.

6.2 Press plus button to set the power to level 9, then touch plus button “ ” to let the power

level alternately display “ ” and “ ”. At this point, the default timing has started. For example,

after “ ” and “ ”alternately display for 10 seconds, press the“ ” to adjust the power level to

level 6. The icons “ ” and “ ” will display for 2 minutes and 20 seconds. After 2 minutes and

20 seconds, the hob will turn to normal heating mode, corresponding digital power level

indicator will display “ ”.

When setting the automatic heating function, the corresponding cooking zone will be heated

in level 9 for a period of time (heating time depends on the subsequent reduction to several

levels, the heating time of each level is as follows), then continue working in the ﬁnal

adjusted heating level. For example, set the heating level to 9th level and activate the

automatic heating function by pressing the “ ” key (alternately display “ ”and“ ”). Then set

the automatic heating function level to level 6 with minus button “ ”. In this setting, the

cooking zone is heated at level 9 for 2.5 minutes. The digital cooking zone indicator alternately

displays “ ” and “ ”. Then continue heating at level 6, the digital indicator will display

“ ”.

6.3 The power level and corresponding timetables of auto-heating are as below:

Power Level 1 2 3 4 5 6 7 8 9

Fast-heating

time minute 1 3 4.8 6.5 8.5 2.5 3.5 4.5 5

6.4 Automatic heating level adjustment: When entering automatic heating mode

auto-heating at max power within 30s, pressing minus button “ ” can reduce the power. After

more than 30 seconds, pressing the minus button“ ”can not reduce the automatic heating

level, it will exit the auto-heating mode.

After more than 30 seconds, as long as it is still in the automatic heating mode and the

automatic heating level is less than 9th level, press the plus button“ ” to increase the

automatic heating level, and the system continues to be in the automatic heating mode.

For example, after entering the automatic heating mode, within 30 seconds touch minus

button “ ” to adjust auto-heating level to level 8. The digital indicator will display “ ”

and “ ”. And then reduce to level 7, the digital indicator will display “ ” and “ ”. At this

moment, the hob is still in the automatic heating mode. After more than 30 seconds, level

14

7 can not be reduced to level 6, the automatic heating mode can be exited, and the hob changes

to normal heating mode, the digital indicator will display “ ”.

6.5 When changing the automatic heating level, the elapsed time will be automatically

calculated into the time corresponding to the new automatic heating level.

For example, you have selected the automatic heating level to be level 1 (1 minute), and after

30 seconds you change the level to level 4 (6.5 minutes). This automatic heating function will

run accurately for 6 minutes (6.5 minutes minus 30 seconds).

6.6 Within 30 seconds of automatic heating mode operation, press the minus button “ ” to

adjust to a certain level, then the running time is counted in the set level time.

For example, when the indicating digital tube “ ” and “ ” is alternately displayed and has

been running for 20 seconds. Press the minus button “ ” to adjust to 6th level, then the 20

seconds that have been run will be automatically counted in the 2.5 minutes of the 6th level,

while the 6th level will continue to run for 2.5 minutes minus 20 seconds, that is2minutes

and 10 seconds. Then turn back to normal heating mode.

7. Timer adjustment

After selecting the corresponding power of the cooking zone, press the time button“ ”, the

digital timer will display “00” and the decimal point on the right will display “ ”.

At this time, the timing mode is entered, and the timing time of the selected burner can be

set (The following operations are required in timing mode).

If you want to cancel the timing, you can adjust the timing time to zero.

The ﬁrst time you press the plus button“ ”, the timing starts from 1 minute, after which

you can press the plus or minus button to adjust the timing time.

Press the plus button“ ” for each time the buzzer will beep once, and the heating time

will be increased by 1 minute. The timing will be continuously changed between 1-

99 minutes. The maximum adjustment is to 99 minutes.

Press the minus button “ ” for each time the buzzer will beep once, and the timing will

be reduced by 1 minute. When the timing time is less than or equal to 30 minutes, the

continuous timing adjustment will continuously change between 30-0 minutes; If the

timing has been adjusted with the plus button “ ” for more than 30 minutes, press the

minus button“ ” to adjust the timing to 0, and continue to change the timing

continuously between 30-0 with the minus button.

After the timer countdown is 0, the buzzer will continue to sound for 2 minutes, and you

Note :

1. If the timing of a certain cooking zone has been set, to change the time, press the time

button again to select the corresponding cooking zone, and then enter the new time with

plus and minus buttons.

2. After the cooking zone is selected, the timing setting cannot be made before the cooking

zone power is set, and the time button is invalid.

3. When the timing of a certain cooking zone is set for the ﬁrst time, if the cooking zone

selection button corresponding to the cooking zone is pressed when the timing is not

conﬁrmed, the timing of the cooking zone is canceled.

15

4. When single or multiple cooking zones are working, the decimal point “ ” of the

corresponding cooking zone is always displayed during the timing setting process.

When multiple cooking zones are working, if two or more cooking zones have times set,

the digital timing indicator displays the minimum timing of the cooking zone.The decimal

point of corresponding cooking zone is always on. The digital decimal point “ ” is o

until the countdown time is over.

8. Powe

Under standby mode or heating mode, long press “ ” button for 3s, a short audible signal will

has residual heat at this time, the digital power level indicator will ﬂash display “ ”, and

indicate residual heat warning.

9. Child Safety lock button

The control panel can be locked by pressing and holding the child safety lock button “ ”

for 3 seconds whilst the appliance is under standby status or heating status. The safety

lock icon will display. When the appliance is o, the safety lock icon will switch o

Under the child safety lock mode, the “ ” will display and ﬂash (1s/time). If the cooking

zone has a set time, the digital indicator will display the time and “ ” alternately. If not,

it will display “ ” and “ ”.

Under the child safety lock mode, you can unlock it by pressing and holding the child lock

button “ ” for about 3 seconds.

In the child safety lock mode, except for press

as well as pressing and holding the child lock button to unlock, the other buttons are invalid.

10. Partition timing

The timer can be timed separately for any cooking zone, and the timing of each cooking zone

is independent of each other.

Single cooking zone timing

When setting a countdown time for a cooking zone, press timer button“ ” ﬁrst, the digital

decimal point “ ” of the selected cooking zone will be on. The decimal point of the digital

timer “ ” will display, to indicate the set timer is related to the selected cooking zone.

At this time, you can use the plus button and minus button to set the countdown

time.

Several cooking zones timing

Each timer setting operation will be same as “Single cooking zone timing”.

Press any cooking zone selection button, and the digital timer displays the timing

value of that cooking zone.

pressing the time button “ ”.

When not selecting any cooking zone, the digital indicator will show the minimum timer

value of cooking zones, and the digital indicator of corresponding cooking zone will show “ ”.

11. Default timing

All the cooking zones have a default timing function. The relationship of default timing and

power level refers to table below:

16

Power Level 1 2 3 4 5 6-9

Default timing (h) 6h 6h 5h 5h 4h 1.5h

When all the default timing is reached, the coo tomatically

and enter into standby mode.

12. High temperature warning

stop heating, but the cooking surface still has high temperature, the digital indicator of

corresponding cooking zone which stops heating will show residual heat warning symbol

“ ”, to indicate corresponding cooking surface high temperature.

As long as the cooking zone has heated before, the high temperature warning symbol “ ”

High temperature protection: The electronic temperature sensor on the control panel will

transmit the real-time temperature to the chip of the control panel. The control sensor

starts protection when the electronic temperature sensor gauges the current temperature

is higher than a certain value, reducing the heating level of the cooking zone currently,

and resumes the heating level after the temperature drops.

Residual heat protection: When the whole appliance stops heating, the digital indicator of

the relative heating zone will display high temperature warning symbol “ ”, indicating

that cooking surface temperature is too high, please do not touch to avoid getting burned.

voltage between L/N of the plug should fall to the safe voltage range.

13. PCB board fault codes and solutions

When a PCB board failure occurs, the digital timers on the display panel always display

the fault code, and all the burners that are being heated stop heating, and automatically

return to the shutdown state after 1 minute. For the burners that have been worked, the

corresponding digital indicator continues to display the high temperature warning sign " ".

When the fault code appears, please refer to the scheme in the following table to solve.

Solution

E1 The display board does not receive

the signal of power supply board.

The communication line failure of

power supply board or display board

can cause communication anomalies.

Replace the display board ﬁrst. If the

fault persists, replace the power

supply board.

E2 The power supply board does not

receive the signal of display

board.

E3 Power supply board relay failure Replace the power supply board.

E4 1. Open circuit of the display board

NTC.

2. short circuit of the display board

Replace the display board

17

Type of fault

How to use the hot plate

Put the pot in the center of the heating zone, and then turn on the hob.

High temperature indication lamp:

When the glass plate is too hot, the high temperature indication lamp will light up, don’t

touch the glass plate until the indication lamp goes out.

Caution!

Ensure the heating plate is clean -a soiled zone does not transfer all of the heat.

Protect the plate against corrosion.

Switch o the plate to prevent corrosion.

Do not leave pans with prepared dishes based on fats and oils unattended on the

switched-on plate; hot fat can spontaneously catch ﬁre.

Hob guidelines

The ﬁrst few times the hob top is used, it may give o an acrid, burning smell. This smell

willdisappear completely with repeated use.

The hob is ﬁtted with cooking areas of dierent diameter and power.

The positions where the heat will radiate from are clearly marked on the hob top. The

saucepans must be positioned exactly on these zones for ecient heating to occur. Pans

should have the same diameter as the cooking zone that they are being used on.

You should not use saucepans with rough bottoms, as this can scratch the ceramic

surface.

Before use, make sure that the bottoms of the saucepans are clean and dry.

When cold, the bottom of the pans should be slightly concave, as they expand when hot

and lie ﬂat on the surface of the hob. This will allow the heat to transfer more easily.

The best thickness for the bottom of the pans is 2 – 3 mm of enamelled steel and 4 – 6

mm for stainless steel with layered bottoms.

If these rules are not followed, then there will be a great loss of heat and energy. Heat not

absorbed by the saucepan, will spread to the hob, frame and surrounding cabinets.

NTC.

E5 High temperature protection on

the display board.

Replace the Insulated silicone strip of

circuit panel ﬁrst. If the fault persists,

replace the display board .

wrong wrong wrong wrongright

18

Preferably cover pans with a lid to permit cooking at a lower heat.

Always cookvegetablesand potatoes, etc. in as little water to reduce cooking times.

Food or liquid that has high sugar content may damage the hob top if it comes into

contact with the ceramic hob surface. Any spillages should be wiped up immediately,

however this may not prevent the hob surface from becoming damaged.

IMPORTANT: The ceramic hob surface is tough; however it is not unbreakable and can be

damaged. Especially if pointed or hard objects are allowed to fall on it with some force.

Maintenance and cleaning

Cleaning operations must only be carried out when the hob is cool.

The appliance should be disconnected from your mains supply before commencing

any cleaning process.

Cleaning the ceramic hobtop

Any residues that are left on the hob top surface from cleaning agents will damage it.

You should remove any residues with warm water mixed with a little washing up liquid.

Abrasive cleaners or sharp objects will damage the hob surface; you should clean it

using warm water mixed with a little washing up liquid.

You may ﬁnd it easier to clean some deposits whilst the hob surface is still warm.

However you should take care not to burn yourself if cleaning the hob surface when

it is stillwarm.

After each use

Wipe the appliance over with a damp cloth.

Dry the appliance by rubbing the surface with a clean cloth.

Cleaning list

Type of deposit Remove

immediately?

Remove when the

appliance

has cooled down?

Whatshould I use to

remove the deposit?

Sugar or food/liquid

containing sugar Yes No Ceramic hob scraper

Tinfoil or plastic Yes No Ceramic hob scraper

Fat splashes No YesCeramic hob cleaner

Metallic discolouration No YesCeramic hob cleaner

Water splashes or water

ringsNo Yes Ceramichob cleaner

Important!

The inside of the hob should only be washed with warm water and a small amount of

washing-up liquid.

Caution!

Ensure the heating plate is clean -a soiled zone does not transfer all of the heat.

19

Protect the hob against corrosion.

Switch o the hob to prevent corrosion.

Do not leave pans with prepared dishes based on fats and oils unattended on the switched-on

plate; hot fat can spontaneously catch ﬁre.

IMPORTANT: If your appliance appears not to be operating correctly, Please contact

dealer.

DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF.

Please note that if an engineer is asked to attend whilst the product is under guarantee and

ﬁnds that the problem is not the result of an appliance fault, then you may be liable for the

cost of the maintenance request.

The appliance must be accessible for the engineer to perform any necessary repair. If your

appliance is installed in such a way that an engineer is concerned that damage will be caused

to the appliance or your kitchen, then he will not complete a repair.

Speciﬁcation:

Model No.: POIH3060C4E4

Rated voltage: 220-240V~ or 380-420V~ 2N 50/60Hz

Total power: 6600W

Model identiﬁcation POIH3060C4E4

Cooking Zones 4 Zones

Supply Voltage 220-240V~ or 380-420V~ 2N 5

Installed Electric Power 6600W

Product SizeDx W x H (mm) 580×510×50

Built-in Dimensions AxB (mm) 560×490

For circular cooking zones or areas: diameter of

useful surface area per electric heated cooking

zone, rounded to the nearest 5 mm

Left down: 14.0 cm & 23.0 cm

Left up: 16.5 cm

Right down: 16.5 cm

Right up: 16.5 cm & 27.0 cm

Energy consumption per cooking zone or area

calculated per kg

EC electric cooking(Wh/kg )

Left down: 194.9

Left up: 187.1

Right down: 198.3

Right up: 193.6

Energy consumption for the hob calculated per kg

EC electric cooking ( Wh/kg ) 193.5

20

Sidan laddas ...

POINT 3-SERIES POIH3060C4E4 KERAMISK TOPP Bruksanvisning

POINT 3-SERIES POIH3060C4E4 KERAMISK TOPP Bruksanvisning

på andra språk

Relaterade papper

Andra dokument