Yamaha CRW2200UX Användarmanual

Kategori
Optiska skivenheter
Typ
Användarmanual

Denna manual är också lämplig för

(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party: Yamaha Electronics Corporation, USA.
Address: 6660 Orangethorpe Avenue
Buena Park, CA 90620
Telephone: 714-522-9105
Fax: 714-670-0108
Type of Equipment: CD Recordable/Rewritable Drive
Model Name: CRW2200UX
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that
may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product
in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses
radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause
interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product is found to be the source of interference, which can be determined
by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this
type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corporation, USA.
6660 Orangethorpe Avenue, Buena Park, CA 90620 U.S.A.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
Laser Product Class: Class 1
Laser Diode Properties
Wavelength: 780-787 nm
Pulse Durations and Max. Output
at the lens of the Laser Pickup Unit
Read Mode: 0.7mW (Continuous)
Write Mode: Max. 38mW
(for 166ns, Min. Cycle 86.6ns)
ACHTUNG
Halten Sie sich beim Bedienen und Einstellen der
Bedienungselemente sowie bei der Bedienungsabfolge
an die Anleitung, da sonst gefährliche Strahlen austreten
können.
ATTENTION
Lemploi de commandes, de réglages ou un choix de
procédures différents des spécifications de cette
brochure peut entraîner une exposition à d’éventuelles
radiations pouvant être dangereuses.
PRECAUCION
El usar los controles o ajustar o realizar procedimientos
diferentes a los especificados aquí resultará en
peligrosas exposiciones a la radiación.
VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA
OLET ALTTINA NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN. STRÅLEN ÄR FARLIG.
Laserprodukt-Klasse: Klasse 1
Eigenschaften der Laserdiode
Wellenlänge: 780-787 nm
Impulsdauer und max. Ausgang an der Linse der
Laser-Abtasteinheit
Lesemodus: 0,7mW (kontinuierlich)
Schreibmodus: Max. 38mW
(für 166ns, Zyklusmin. 86,6ns)
Classe du produit laser: Classe 1
Caractéristiques de la diode laser
Longueur d’onde: 780-787 nm
Durée des impulsions et sortie maximum depuis
la lentille du bloc capteur optique
Mode de lecture: 0,7mW (continue)
Mode de gravure: max. 38mW
(pour 166ns, cycle min. 86,6ns)
Clase de producto láser: Clase 1
Propiedades del diodo láser
Longitud de onda: 780-787 nm
Duración del pulso y potencia de salida máxima
en el objetivo de la unidad captora láser
Modo de lectura: 0,7mW (continua)
Modo de escritura: máx. 38mW
(para 166ns, ciclo mínimo 86,6ns)
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
PRODUIT LASER DE CLASSE 1
DANGER - VISIBLE AND / OR INVISIBLE LASER
RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE
TO BEAM.
CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA
DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.
VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI
NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.
VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG
WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.
ATTENTION - RADIATION VISIBLE ET / OU INVISIBLE LORSQUE L’APPAREIL
EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.
COMPLIES WITH 21 CFR CHAPTER 1, SUBCHAPTER J.
i
OWNER’S MANUAL
English
ii
PLEASE READ THE FOLLOWING WARNING AND
PLEASE READ THE FOLLOWING WARNING AND PLEASE READ THE FOLLOWING WARNING AND
PLEASE READ THE FOLLOWING WARNING AND
CAUTION CAREFULLY TO PROTECT YOUR PERSONAL
CAUTION CAREFULLY TO PROTECT YOUR PERSONAL CAUTION CAREFULLY TO PROTECT YOUR PERSONAL
CAUTION CAREFULLY TO PROTECT YOUR PERSONAL
SAFETY AND PREVENT DAMAGE TO THE DEVICE.
SAFETY AND PREVENT DAMAGE TO THE DEVICE.SAFETY AND PREVENT DAMAGE TO THE DEVICE.
SAFETY AND PREVENT DAMAGE TO THE DEVICE.
These precautions explain how to use the device correctly and safely, thereby preventing injury to
yourself or to others. This section has been sub-divided into a WARNING section and a CAUTION
section, according to the likelihood and nature of any potential injuries or damage inflicted. They relate
to your personal safety, and also help you minimize the risk of damaging the device. Please read these
sections carefully before proceeding.
WARNING
Always follow these basic precautions to prevent short-circuit, damage, fire, or other hazards,
and to prevent serious injury or death from electrical shock.
To avoid risk of electrical shock or fire, do not attempt to open or disassemble the device.
To avoid risk of eye damage or blindness, do not look inside the device.
To avoid the risk of personal injury or electrical shock, do not insert your fingers, or foreign objects
into the device. Please take particular care if small children are present.
To avoid the risk of electrical shock, fire, or personal injury, do not expose the device to rain, use it
near water, or in damp or wet conditions, or place containers that contain liquids (they may spill into
the unit) on the device.
To avoid risk of personal injury, electrical shock, fire, or damage to the unit, follow the Owner’s
Manual carefully and set up the unit correctly.
If unusual smells, sounds or smoke come from the device, turn off the computer immediately to
avoid the risk of electrical shock, fire or damage to the device, and return the device to the place of
purchase, or alternatively, to your nearest Yamaha dealer (listed at the back of this manual).
Make sure the computer is electrically grounded to avoid the risk of electrical shock.
When opening up the computer, unplug it from the electrical outlet (do not touch the plug with wet
hands) as there is an increased risk of electrical shock.
The drive should not be exposed to temperatures outside the range of 5 – 35 °C (41 – 95 °F) to
avoid risk of malfunction, fire or personal injury.
To avoid the risk of electrical shock or fire, be sure to use the correct voltage rating, or the device
may not operate properly.
AC adapter Rated Input Voltage SKB2505A : 100 – 120 V AC ± 10%
SMB2505A : 220 – 240 V AC ± 10%
Clean the AC power plug regularly, especially the blades, to avoid the risk of insulation failure or fire
due to humidity.
Do not pull on the cord itself when disconnecting from the electrical outlet, or let objects rest or roll
over the cord, as the cord can be damaged and cause electrical shock or fire.
SAFETY PRECAUTIONS
iii
Insert the AC plug firmly, as a poor connection can result in electrical shock or fire.
Only use the included AC adapter, as malfunction or fire may result.
Do not connect too many devices to a single electrical outlet, or use voltages exceeding the rated
voltage as this may cause overheating and fire.
CAUTION
Always follow these basic precautions to prevent physical injury to yourself or others, or damage
to the instrument or other property.
To avoid the risk of electrical shock or fire, always unplug the computer from the electrical outlet if it
will not be used for a prolonged period of time, or if there is a risk of lightning.
Do not expose the device to excessive vibration, heat, cold or dust, as doing so may result in damage
to the unit’s front panel or its internal components.
Do not use the device near other products such as televisions, radios, or speakers as this may cause
interference, which can affect the proper operation of the device or other devices.
To avoid damage to the device or personal injury, always place the device in a stable position.
Always place the device horizontally to avoid the risk of lost written data.
Always remove any disc from the disc tray before transporting the device as written data may be lost.
Use a soft, dry cloth to wipe the device. Do not use benzene, paint thinners, detergents, or
chemically treated wiping cloths as these may damage the unit.
Do not place vinyl, plastic, or rubber objects on the device as chemical reactions can cause damage
to the device.
Do not rest your weight on or place heavy objects on the device, or use excessive force on the
buttons, switches or connectors, as damage to the unit or personal injury may occur.
Do not listen to audio with headphones at high volume for prolonged periods of time as your hearing
may be damaged as a result.
Before using the device, always turn down the volume as sudden bursts of sound can result in
hearing damage.
Do not place the device anywhere near sources of magnetic interference as operational stability may
be adversely affected.
Have the device serviced regularly to avoid internal dust buildup that can cause malfunction, damage
or fire. For service information, and about service charges, contact the store of purchase, or your
nearest Yamaha dealer (listed in the back of this manual).
Do not allow the plug of the AC adapter to come into contact with metal as a short circuit can result
and cause a malfunction or damage to the device.
Do not wrap the power cord around the AC adapter as it may become disconnected and cause a malfunction.
iv
About handling CD-R/RW discs
1. Do not store discs in areas subject to excessive humidity or heat (i.e., in direct sunlight or
near a heater).
2. Do not touch the surface of a disc.
When handling a disc, hold it by the edges.
3. Remove dust and dirt from the surface of a disc.
Use an air-blower (i.e., camera lens blower) to remove dust. The surface of a disc may be
scratched if wiped with a dry cloth.
4. Do not stick labels on the surface of a disc.
5. Do not write on the surface of a disc except where indicated.
6. Do not clean discs with chemicals or detergents.
7. Do not bend or drop discs.
8. Use only circular discs. Do not use irregularly shaped discs, such as star, heart or card
shaped, etc., as these could damage your new CD-R/RW drive.
Precautions for Transportation
Keep the original box for future transportation. Before transporting the device, always put it
in the original box. Yamaha does not bear any responsibility for any problem that occurs
during transportation with the device not in the original box.
Copyrights
When writing to a CD-R/RW, make sure that you do not infringe on any copyrights. It is
illegal to copy audio CDs for non-personal use. When backing up software, make sure that
you do not infringe on any software copyrights for that product.
WARRANTY
YAMAHA AND ITS SUPPLIERS ACCEPT NO LIABILITY FOR THE LOSS OF ANY DATA
OR ANY PROBLEMS CAUSED AS A RESULT OF USING THIS PRODUCT. AS A
PRECAUTION, IT IS RECOMMENDED THAT THE DISCS BE TESTED AFTER THEY
HAVE BEEN WRITTEN TO. FURTHERMORE, UNDER NO CIRCUMSTANCES DOES
YAMAHA AND ITS SUPPLIERS GUARANTEE THE RELIABILITY OF THE DISCS.
1. The information contained in this manual is subject to change
without prior notice.
2. All trademarks contained in this manual belong to their respective
owners.
3. Yamaha does not bear any responsibility for a problem that occurs
as a result of any operations carried out other than those stated in
the manual included with the drive.
4. Reproduction of this manual, either in part or in full, is expressly
forbidden.
v
Table of Contents
Introduction........................................................................ 1
Features of the CRW2200UX Drive .................................................. 1
Before Use ......................................................................... 4
System Requirements.......................................................................... 4
Supported Discs................................................................................... 6
Serial Number ..................................................................................... 8
Front and Rear of Unit............................................................ 9
Front Panel .......................................................................................... 9
Rear Panel ......................................................................................... 10
Setup Procedures ................................................................11
Setup Flowchart................................................................................. 11
STEP 1 Set Up the CRW2200UX Drive......................................... 12
STEP 2 Install the Device Drivers ................................................... 15
STEP 3 Configuring for the Operating System................................ 16
STEP 4 Install the CD Writing Software ......................................... 17
Operation..........................................................................18
Loading/Ejecting a Disc.................................................................... 18
Ejecting a Disc in an Emergency ...................................................... 19
Disconnecting the CRW2200UX Drive ........................................... 20
Troubleshooting..................................................................21
Appendix...........................................................................26
Recording Methods ........................................................................... 26
About the Firmware .......................................................................... 29
LED Indicator Messages................................................................... 30
CRW2200UX Specifications............................................................ 31
Index.................................................................................................. 34
©2001 YAMAHA CORPORATION. All Rights Reserved.
This document may not, in whole or in part, be copied, photocopied, reproduced,
translated, transmitted, or reduced to any electronic medium of machine readable
form without prior consent in writing from Yamaha.
Windows is a registered trademark of Microsoft Corporation.
SafeBurn™ is a trademark of Yamaha Corporation.
All other trademarks are the property of their respective companies.
1
Introduction
High speed writing/reading
The CRW2200UX drive supports up to 20X-speed writing of CD-R discs,
*1
and up
to 10X-speed writing/rewriting of CD-RW discs.
*2
Furthermore, the drive supports
data reading and digital audio data extraction at up to 40X speed.
USB 2.0 compatible
USB 2.0 provides high-speed data transfer capability (max. speed 480 Mbits/sec.).
The transfer speed is about 40 times faster than the conventional USB standard
(USB 1.1).
USB’s hot swapping capability allows the drive to be plugged in and unplugged even
with the computer turned on.
SafeBurn™ (Enhanced write stability technology)
Generous 8MB of buffer memory
Because of the large data storage area, stable disc writing is possible even at fast
speeds.
Buffer Underrun Protection
When data transfer from the host PC is interrupted, Buffer Underrun Protection is
activated to keep precious CD-R discs from going to waste. (
P. 3)
Optimum Write Speed Control
Before writing to a CD-R, the CRW2200UX drive checks the discs capability and
automatically selects the optimum writing speed
*3
for greater reliability. The speed
you set is the maximum writing speed.
Reliable writing
Yamaha’s proprietary Pure-Phase Laser System (patent applied for)
This technology reduces phase interference of the laser beam, so that it projects
accurately onto the disc. Jitter value, an important measure of recording quality, has
been improved 25% compared with Yamaha models not using this technology.
Running OPC (Optimum Power Control)
Running OPC automatically adjusts the output of the laser according to the
characteristics of the disc being used. Running OPC provides greatly enhanced
recording reliability for various manufacturers discs.
Features of the CRW2200UX Drive
Introduction
2
High-fidelity digital audio
The CRW2200UX drive supports extraction of digital audio data at up to 40X speed,
as well as the recording of digital sound with complete fidelity even when writing at
20X speed.
CD TEXT support
Information such as the song name or artist name can be recorded on Audio CDs
using CD creation software. The text data on the created disc can be displayed on a
CD player that is compatible with the CD TEXT format.
*1 16X- or 20X-speed writing is enabled with the Partial CAV method. (
P. 7)
*2 10X-speed writing/rewriting is enabled with the CLV method and the 4X-10X Full CAV method. (
P. 8)
*3 The optimal writing speed automatically selected will be between 8X speed and the maximum speed designated
for that disc. If the disc is rated at lower than 8X speed writing, you need to designate the most suitable writing
speed manually.
Introduction
3
Buffer Underrun Defined
CD-R/RW drives are equipped with buffer memory. This memory temporarily
stores data while a disc is being recorded. When buffer memory becomes empty
(due to unexpected interruptions or the systems inability to keep up with the
writing process), a writing error occurs. This error is known as a buffer
underrun error.
A Buffer Underrun Error will permanently ruin the disc.
Yamaha Buffer Underrun Protection
Buffer Underrun Protection is featured in Yamahas CRW2200 series CD-R/
RW drives. When a buffer underrun is about to occur, a buffer underrun error is
prevented by temporarily suspending the writing process. Writing resumes when
enough data has accumulated again in buffer memory. Buffer Underrun
Protection on the CRW2200 series is extremely accurate, resulting in seamless
recording between stop and continuation points.
Yamaha Buffer Underrun Protection ensures error-free results.
Test-writing for Buffer Underrun
Test writing is a function to check for the likely occurrence of Buffer Underrun on your
computer system.
Most writing software includes test writing functions for this purpose.
When the Buffer Underrun Protection is set to ON (Default), test writing cannot be selected
on your writing software.
To use test writing, the Buffer Underrun Protection should be set to OFF.
➀➁
Data
If data transfer is
interrupted...
Data is stored in
buffer memory...
then buffer memory
begins to empty
When no data is left
in buffer memory...
(Buffer Underrun)
and then written
to disc
writing fails
(Buffer Underrun
Error)
➀➁
If data transfer is
interrupted...
Once data transfer
resumes normally...
and buffer memory is
about to empty...
and enough data has accumulated
in buffer memory...
writing is suspended writing resumes
4
Before Use
If your computer doesnt meet the requirements listed below, the CRW2200UX
drive may not be able to write at the maximum speed.
Computer
PC/AT-Compatible Computer
CPU: Pentium II-class or higher, 300 MHz or faster.
RAM: 64 MB or more
USB port (USB 2.0 compatible)
A spare PCI expansion slot or a CardBus slot for a USB interface card (if one hasnt
been installed yet).
CD-ROM drive
Notes
To install the device drivers, you need a CD-ROM drive other than the CRW2200UX drive.
The CRW2200UX drive cannot be used as a boot drive. Furthermore, the CRW2200UX drive
cannot be used to set up the OS one more time.
USB 2.0 Interface Card (PCI or CardBus)
Your computer requires a USB port in order to connect the CRW2200UX drive.
To fully utilize the performance of the CRW2200UX drive, a USB 2.0 compatible
interface card and EHCI (Enhanced Host Controller Interface) compliant driver are
also necessary.
If your computer has a USB port with USB 1.1 specifications, we recommend that
you install a USB 2.0 compatible interface card.
Notes
For the latest information about approved USB 2.0 interface cards, refer to the YAMAHA CD-
R/RW Drive web site.
URL: http://www.yamaha.co.jp/english/product/computer/
For information on how to purchase the EHCI compliant driver for the USB interface card, or
information about the OS supporting the card, refer to the interface card manufacturer web site,
or contact user support services.
Connecting the drive to a USB port with USB 1.1
When the CRW2200UX drive is connected to a USB 1.1-compliant port on your
computer, it operates in accordance with USB 1.1 standard.
For reliable data writing, the Buffer Underrun Protection should be set to ON, and the
writing speed should be set to 8X on the writing software.
Reading is 6X speed at the maximum.
System Requirements
Before Use
5
USB cable
The USB standard for maximum length of cable between devices is five meters.
Operating System (OS)
Windows 98 Second Edition, Windows Me, or Windows 2000 Professional
Notes
For Windows 98 Second Edition, install the included device drivers (storage class drivers) to the
PC. For details, refer to the separate manual, Device Driver Installation Guide, that came with
the CRW2200UX drive.
The CRW2200UX drive cannot be used with a system that has been booted on MS-DOS or
Safe mode.
CD Writing Software
The CRW2200UX drive requires a CD writing software to write onto a CD-R/RW
disc. Make sure your CD writing software supports the CRW2200UX drive.
Note
For details about how to install and use the software, refer to the documentation that came with it.
Hard Drive Space
Writing data on a CD-R/RW disc requires 50 MB to 100 MB of free space as a
working area on the hard drive.
When writing data on a CD-R/RW disc after creating an image file, there must be
enough free space on the hard drive to store the image file in addition to the working
area (a total of up to about 900 MB).
However, this hard drive space for image files is not needed when directly writing
onto a CD-R/RW disc from a hard drive or CD-ROM using the CRW2200UX drive
(on-the-fly writing).
About disk image files
You can collect data files into a single disk image file for a CD-R/RW disc. Also, note that an
image file is useful when writing multiple discs with the same content. For further details, refer to
the documentation that came with your CD writing software.
CRW2200UX
Maximum length of cable
between devices : 5.0 m
Before Use
6
The CRW2200UX drive can write to discs that carry the following logos:
*1 Compatible with Orange Book Part 2.
*2 Compatible with Orange Book Part 3 Vol. 1.
*3 Compatible with Orange Book Part 3 Vol. 2.
Note
To find current information about approved discs for the drive, refer to the YAMAHA CD-R/RW
Drive web site.
URL: http://www.yamaha.co.jp/english/product/computer/
Supported Discs
CD-R discs
*1
The CRW2200UX drive can write to these discs at 1X, 2X, 4X, 8X, 12X,
16X, or 20X speed. These discs can be played back in a CD-ROM drive or a
CD player.
Notes
16X- or 20X-speed writing is enabled with Partial CAV method. (
P. 7)
For 8X or faster writing, use CD-R discs that match their respective writing
speeds.
CD-RW discs
*2
There are two types of CD-RW discs: those that support write/rewrite speeds
of 1X, 2X, and 4X, and those that support only 2X. The CRW2200UX drive
can write/rewrite at 2X or 4X speed on the first type of disc, and at 2X on the
second type of disc. These discs can be read/played on a device (e.g., CD-
ROM drive) that supports CD-RW.
High Speed CD-RW discs
*3
These discs allow writing/rewriting at 4X to 10X speeds. The CRW2200UX
drive can write/rewrite these discs at 4X, 8X, or 10X speed. These discs can be
read/played by a CD-RW drive that bears the High Speed CD-RW logo, or by
a device (e.g., CD-ROM drive) that supports CD-RW.
Note
10X-speed writing/rewriting is enabled with the CLV method, and the 4X-10X
Full CAV method. (
P. 8)
In order to write, erase, or read these discs using a CD-R/RW
drive, a drive bearing the High Speed CD-RW logo must be
used. When using a CD-ROM drive to read these discs, the
drive must be capable of reading CD-RW discs.
If these discs are used in a CD-R/RW drive not bearing the
High Speed CD-RW logo, the discs may not be recognized,
resulting in the computer not operating correctly or other
malfunctions occurring.
Refer to the page at the URL below before attempting to read
these discs on a Yamaha CD-R/RW drive not bearing the
High Speed CD-RW logo.
URL: http://www.yamaha.co.jp/english/product/computer/
Before Use
7
About the Orange Book
The Orange Book standard defines how all recordable discs (including CD-R and CD-RW) are
written. Part 2 of the Orange Book standard relates to CD-R discs, and Part 3 to CD-RW discs.
The standard was named after the color of the books cover.
About CD-ROMs
A CD-ROM disc is a compact disc containing high-density read-only data. It has
many applications, including the playback of music and video, the archiving of
data, as well as on-line documentation. The following are descriptions of each
CD-ROM format:
CD-DA: Up to 79 minutes of stereo audio is written in 16-bit resolution at a
sampling rate of 44.1 kHz for a 79 minute disc.
Data CD: Up to 700 megabytes of computer data is stored in standard ISO9660
format for a 700 MB disc.
Video CD: These hold movies in which video and audio data has been
compressed using MPEG-1 technology.
About Partial CAV (Constant Angular Velocity)
Writing to a CD-R disc is normally done using the CLV (Constant Linear
Velocity) method. In this method, the disc rotation speed is adjusted so as to
keep a constant data transfer rate at any portion of the disc. In other words, the
disc rotation speed will vary in CLV writing.
In contrast, the CAV (Constant Angular Velocity) method uses a constant disc
rotation speed for all portions of the disc so that the data transfer rate will vary.
Because the CAV method has the advantage of largely increasing the data
transfer rate with a minimum load to the drives mechanism (compared to CLVs
rotation speed adjustment), many current CD-ROM drives use the CAV method.
CD formats define the constant linear density of written data (data should be
written onto the disc at a constant pitch) so that the amount of recorded data per
disc rotation will increase as the writing point moves from the inner to the outer.
In other words, in CAV writing, the outer portion has an increased data transfer
rate.
The CRW2200UX drive uses the CAV method in the inner portions as well as
the CLV method in the outer portions (Partial CAV) in order to enable up to
20X-speed writing. The drive will control the disc rotation speed to start writing
at 12X speed in the inner portions, gradually accelerating up to 20X speed and
maintaining 20X speed in the outer portions.
Before Use
8
When you take the CRW2200UX drive out of its packaging, you should immediately
write down the serial number found at the bottom of the drive with the bar code. You
may need to refer to this number when requesting Customer Support services. In the
box below the following diagram, write down the 10-character serial number
(consisting of 3 letters followed by 7 digits).
About 10X-speed writing/rewriting of a High Speed CD-RW disc
10X-speed writing/rewriting of a High Speed CD-RW disc is enabled with the
CLV method, and the 4X-10X Full CAV method. Commonly, writing/rewriting
is enabled with the CLV method. When writing/rewriting with packet writing
(
P. 28), you can also select the Full CAV method. For more details, refer to the
documentation that came with your CD writing software. (Make sure that your
CD writing software supports the Full CAV method.) For direct editing of a file
on a CD-RW disc, the Full CAV method is recommended.
Serial Number
Serial No.
Serial number
(3 letters and 7 digits)
9
Front and Rear of Unit
Power LED
Lights up in green when the power of the drive is turned on.
Disc tray
The disc tray is used to hold the disc. It slides out from the drive unit when a disc needs to
be loaded or unloaded. (
P. 18)
Manual eject hole
Only use this if no other method is available for unloading a disc. (
P. 19)
Eject button
Press this button when you need to open or close the disc tray. (
P. 18)
Headphone jack
You can connect stereo headphones to this stereo mini jack and listen to an audio CD
loaded in the drive.
Headphone volume control
Adjust this control to set a suitable volume level when listening to an audio CD using the
headphone jack. Slide the knob to the left to decrease the volume and to the right to
increase it.
LED
Indicates the operation status of the CRW2200UX drive. (
P. 30)
Front Panel
➁➂
➄➅
Front and Rear of Unit
10
LINE OUT jacks (L/R)
To listen to audio CDs with the CRW2200UX drive, connect these to the line level input
(LINE IN) of the stereo equipment with a standard stereo phono cable (sold separately).
Power switch (STANDBY/ON)
Turns the power on or off. (
P. 12, 14)
DC-IN connector
Insert the included AC adapter connector. (
P. 13)
USB port
Insert the connector of the included USB cable here. (
P. 12)
Rear Panel
➀➂
11
Setup Procedures
For easy cross-referencing, the relevant pages in this manual are given.
Note
Be sure to mount the CRW2200UX drive horizontally.
Setup Flowchart
Do you have an appropriate USB 2.0
interface card?
The card should be compatible with your
computer.
Does your computer have a USB port
with USB 2.0?
Install the CD writing software.
For details about how to install the software,
refer to the documentation that came with it.
STEP
4
Make sure that system configuration
(CPU, RAM, OS, etc.) of your computer
meets the requirements of the
CRW2200UX
drive. (
P. 4)
Set up the
CRW2200UX
drive.
(
P. 12 15)
Turn on the computer and the drive,
then use the USB cable to connect
the computer and the drive.
Make sure that the
CRW2200UX
drive is correctly recognized.
(
P. 16)
Start using the
CRW2200UX
drive
Use the drive to create an audio CD, to backup data
on your hard drive, etc.
Install the card to your
computer.
Read the documentation that
came with the card and properly
set up your computer.
Purchase an USB 2.0 interface
card.
For the latest information about approved
USB 2.0 interface cards, refer to the YAMAHA
CD-R/RW Drive web site.
URL: http://www.yamaha.co.jp/english/
product/computer/
STEP
1
STEP
3
No
Yes
No
Yes
Install the device drivers.
(
P. 15)
For Windows 98 Second Edition, install the
included device drivers.
STEP
2
Setup Procedures
12
1
11
1 Turn on the computer.
2
22
2 Make sure that the power switch on the rear panel of the CRW2200UX
drive is set to STANDBY.
3
33
3 Connect the included USB cable with the CRW2200UX drive.
The included USB cable has two types of plugs: series A plug and series B plug.
Insert the series B plug (with a square cross section) of the included USB cable in
the USB port of the CRW2200UX drive.
STEP
1
Set Up the CRW2200UX Drive
Series A plug Series B plug
USB port
USB cable
(included)
Series B plug
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45

Yamaha CRW2200UX Användarmanual

Kategori
Optiska skivenheter
Typ
Användarmanual
Denna manual är också lämplig för