LIVARNO 374873 Bruksanvisning

LED SOLAR SPOTLIGHT

Assembly and safety advice

LED-AURINKOVALAISIN

Asennus- ja turvaohjeet

LED-STRÅLKASTARE MED

SOLCELLER

Monterings- och säkerhetsanvisningar

REFLEKTOR SOLARNY LED

Wskazówki dotyczące montażu oraz

bezpieczeństwa

LED PROŽEKTORIUS SU

SAULĖS BATERIJA

Surinkimo ir saugos patarimas

LED-SOLAARKIIRGUR

Paigaldus- ja ohutusjuhised

AR SAULES BATERIJĀM

DARBINĀMS LED

PROŽEKTORS

Ieteikumi par uzstādīšanu un drošību

LED-SOLARSTRAHLER

Montage- und Sicherheitshinweise

LED SOLAR SPOTLIGHT

IAN 374873_2104

GB Page 5

FI Sivu 27

SE Sidan 49

PL Strona 71

LT Psl 93

EE Lehekülg

115

LV Lpp.

137

DE/AT/CH Seite

159

1.8-2.5m

5.0m 8.0m

90°

DC

B

A1

2

3

4

5

10

11

12

13

6

7

8

9

HG04465A

1.8-2.5m

5.0m 8.0m

90°

A

B C

D

E F

HG04465B

12

4

5

11 12

13

10

8

6

9

17

19 18

15

14

16

7

3

5GB

List of pictograms used ................ Page 6

Introduction ............................. Page 7

Intended use............................... Page 7

Description of parts ......................... Page 8

Technical data ............................. Page 9

Scope of delivery........................... Page 9

General safety instructions............ Page 10

Safety instructions for batteries/

rechargeable batteries....................... Page 11

Before use ............................... Page 13

Charging the rechargeable batteries ............ Page 14

Inserting / replacing batteries ........ Page 15

Installation .............................. Page 16

Start-up .................................. Page 21

Maintenance and cleaning ............ Page 22

Disposal.................................. Page 23

Warranty ................................ Page 24

6 GB

List of pictograms used

Direct current/voltage

CE mark indicates conformity with relevant

EUdirectives applicable for this product.

Motion detector range approx. 5 – 8 m

Detection angle of motion sensor: approx. 90º

Ingress protection (IP) type: IP44 (splash-proof)

Batteries included (Ni-MH)

Illumination time (after activation): approx.30seconds

7GB

LED SOLAR SPOTLIGHT

Introduction

We congratulate you on the purchase of your new product.

You have chosen a high quality product. The instructions for

use are part of the product. They contain important information

concerning safety, use and disposal. Before using the product,

please familiarise yourself with all of the safety information and

instructions for use. Only use the product as described and for the

speciﬁed applications. If you pass the product on to anyone else,

please ensure that you also pass on all the documentation with it.

Intended use

The product is intended to illuminate outdoor areas without

electrical connection. The product is suitable for use in private

household and is not intended for commercial use or for use in

other applications.

Not suitable for ordinary lighting in household room

illumination.

8 GB

Description of parts

[1] Solar panel

[2] ON/OFF switch

[3] Spotlight

[4] Sensor

[5] Dowel (mounting plate)

[6] Mounting plate

[7] Ball joint cover

[8] Screw (mounting plate)

[9] Slot

[

]

Front cover

[

]

Rechargeable battery

[

]

Battery compartment

[

]

Fixing screw (front cover)

[

]

Mounting bracket (HG04465B only)

[

]

Dowel (for mounting bracket) (HG04465B only)

[

]

Screw (for mounting bracket) (HG04465B only)

[

]

Connection cable (HG04465B only)

[

]

Plug (HG04465B only)

[

]

Socket (HG04465B only)

9GB

Technical data

Model no.: HG04465A or HG04465B

LEDs: 6 x 0.08 W

(LEDs are not replaceable.)

Operating voltage: 3.6 V

Rechargeable batteries: 3 x Ni-MH AA, 900 mAh,1.2 V

Degree of ingress protection: IP44 (splash-proof)

Motion sensor: Range: approx. 5 to 8 m

Detection angle: approx. 90º

Scope of delivery

Check immediately after unpacking that the parts are complete

and that the product is in proper condition.

1 LED solar powered spotlight, model HG04465A or

HG04465B

1 Mounting bracket (for solar panel) (HG04465B only)

1 Solar panel (HG04465B only)

2 Dowels (mounting plate)

2 Screws (mounting plate)

2 Dowels (mounting bracket) (HG04465B only)

2 Screws (mounting bracket) (HG04465B only)

1 Assembly, operating and safety instructions

10 GB

General safety instructions

BEFORE USING THE PRODUCT, PLEASE FAMILIARISE

YOURSELF WITH ALL OF THE SAFETY INFORMATION

AND INSTRUCTIONS FOR USE! WHEN PASSING THIS

PRODUCT ON TO OTHERS, PLEASE ALSO INCLUDE ALL THE

DOCUMENTS!

This product can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

use of the product in a safe way and understand the hazards

involved. Children shall not play with the product. Cleaning

and user maintenance shall not be made by children without

supervision.

Never leave children unsupervised with the packaging

material. The packaging material represents a danger of

suﬀocation. Children frequently underestimate the dangers.

Keep children out of the area you are working in. A large

number of screws and other small parts are included with the

delivery. These may prove life-threatening if swallowed or

inhaled.

11GB

Do not use this product if you notice any damage!

The LEDs are not replaceable.

If the LEDs fail at the end of their life, the entire product must

be replaced.

Do not look directly into the light source (light bulb, LED etc.).

Do not look at the LED with an optical instrument (e.g.

magniﬁer).

The external ﬂexible cable of this luminaire cannot be

replaced; if the cord is damaged, the luminaire shall be

destroyed (HG04465B only).

Safety instructions for batteries/

rechargeable batteries

m DANGER TO LIFE! Keep batteries/ rechargeable batteries

out of reach of children. If accidentally swallowed seek

immediate medical attention.

Swallowing may lead to burns, perforation of soft tissue, and

death. Severe burns can occur within 2 hours of ingestion.

12 GB

DANGER OF EXPLOSION! Never recharge

non-rechargeable batteries. Do not short-circuit

batteries/ rechargeable batteries and/ or open them.

Overheating, ﬁre or bursting can be the result.

Never throw batteries/ rechargeable batteries into ﬁre or

water.

Do not exert mechanical loads to batteries/ rechargeable

batteries.

Risk of leakage of batteries/ rechargeable batteries

Avoid extreme environmental conditions and temperatures,

which could aﬀect batteries/ rechargeable batteries, e.g.

radiators/ direct sunlight.

If batteries/ rechargeable batteries have leaked, avoid

contact with skin, eyes and mucous membranes with the

chemicals! Flush immediately the aﬀected areas with fresh

water and seek medical attention!

WEAR PROTECTIVE GLOVES! Leaked or damaged

batteries/ rechargeable batteries can cause burns on

contact with the skin. Wear suitable protective gloves at

all times if such an event occurs.

13GB

In the event of a leakage of batteries/ rechargeable

batteries, immediately remove them from the product to

prevent damage.

Only use the same type of batteries/ rechargeable batteries.

Do not mix used and new batteries/ rechargeable batteries.

Remove batteries/ rechargeable batteries if the product will

not be used for a longer period.

Risk of damage of the product

Only use the speciﬁed type of battery/ rechargeable battery!

Insert batteries/ rechargeable batteries according to polarity

marks (+) and (–) on the battery/ rechargeable battery and

the product.

Clean the contacts on the battery/ rechargeable battery and

in the battery compartment before inserting!

Remove exhausted batteries/ rechargeable batteries from the

product immediately.

Before use

Note: Remove all packaging materials from the product.

14 GB

Charging the rechargeable batteries

Note: The rechargeable batteries [

]

inside the product are fully

charged at delivery. However, they may have lost charge during

transport from the manufacturer to the retail location. Therefore

charge the rechargeable batteries [

]

prior to use. During summer,

initial charging will take at least 1 day in constant sunlight.

Set the ON/OFF switch [2] to the “ON“ position.

Note: In constant sunlight (depending on the season) drained

rechargeable batteries [

]

should take 2 to 10 days to charge.

Note: The built-in charging controller of the product prevents the

rechargeable batteries [

]

from overcharging.

Replace the rechargeable batteries [

]

if light output does

not improve after charging (Fig.C: HG04465A or Fig.E:

HG04465B).

15GB

Inserting / replacing batteries

Note: The rechargeable batteries [

]

are pre-installed. Only use

batteries as stated in the “Technical data” chapter. To remove the

rechargeable batteries [

]

, switch the spotlight [3] oﬀ using the

ON/OFF switch [2].

Open the battery compartment [

]

on the back side

of the spotlight [3] by loosening the ﬁxing screws [

]

counterclockwise to remove the front cover [

]

(Fig.C:

HG04465A or Fig.E:HG04465B).

Remove the old rechargeable batteries [

]

.

Insert the new rechargeable batteries [

]

. Use only batteries

of the speciﬁed type (see “Technical data”).

Note: When inserting the battery, ensure the correct polarity!

This is indicated in the battery compartment [

]

.

Close the battery compartment [

]

again with the front cover

[

]

and ﬁx the front cover [

]

by turning the ﬁxing screws [

]

clockwise.

Note: Make sure the sealing ring is secured correctly before

closing the battery compartment, otherwise the ingress

protection (IP) cannot be guaranteed.

16 GB

Installation

Note: The included mounting material is suitable for ordinary

solid concrete or masonry construction. Other wall substrates

may require other fastening materials. Seek specialist advice if

necessary.

Note: You will need an electric drill.

m CAUTION! RISK OF INJURY! Read the operating

instructions for your drill.

m CAUTION! Ensure that you do not damage any electricity

cables in the wall or ceiling.

When selecting the mounting location, pay attention to the

following:

Ensure that the spotlight [3] illuminates the desired area. You

can swivel the spotlight [3] into the desired position.

Ensure the sensor [4] covers the desired area. The sensor[4]

has a maximum coverage range of approx. 5 to 8 m, with a

coverage angle of about 90° (depending on the mounting

height – a height from 1.8 to 2.5 m is ideal)

(Fig. D: HG04465A or Fig. F: HG04465B).

Ensure the sensor [4] is not illuminated at night by street

lighting. This can inﬂuence its functioning.

17GB

Ensure that the solar panel [1] is mounted in a place with

direct sunlight.

Ensure that the solar panel [1] is not installed where there are

strong temperature ﬂuctuations, e.g. due to heating devices.

Ensure that the solar panel [1] is installed far away from

unnatural light sources and in southern direction.

Ensure that the connection cable [

]

of the solar panel [1]

can reach the spotlight [3]. Max. distance between the solar

panel [1] and the spotlight [3] is approx. 2.5 m (HG04465B

only).

For HG04465A:

Carefully fold the solar panel [1] upwards.

Remove the mounting plate [6] from the spotlight [3] by

loosening the screws of the ball joint cover [7] (Fig. B).

Use the holes of the mounting plate [6] intended for the

screws [8] to mark the drill holes.

Now drill the ﬁxing holes (Ø 8 mm, depth approx. 40 mm).

Before drilling the ﬁxing holes, ensure there are no gas, water

or electrical lines that could be drilled into or damaged in the

area where you will be drilling.

Insert the dowels [5] into the drill holes (Fig. B).

18 GB

Attach the mounting plate [6] using the screws [8] provided

(Fig. B).

Ensure that the solar panel [1] is orientated towards the sun.

Now place the spotlight [3] towards the mounting plate [6].

Ensure that the ball joint of the mounting plate [6] is correctly

inserted into the slot [9] of the spotlight [3]. Then, close the

ball joint cover [7] by tightening the screws clockwise (Fig. B).

Set the ON/OFF switch [2] on the spotlight [3] to the “ON“

position (Fig. A).

The rechargeable batteries [

]

will now charge when there is

suﬃcient solar radiation.

For HG04465B:

Remove the mounting plate [6] from the spotlight [3] by

loosening the screws of the ball joint cover [7] (Fig. B).

Use the holes of the mounting plate [6] intended for the

screws [8] to mark the drill holes.

Now drill the ﬁxing holes (Ø 8 mm, depth approx. 40 mm).

Before drilling the ﬁxing holes, ensure there are no gas, water

or electrical lines that could be drilled into or damaged in the

area where you will be drilling.

19GB

Insert the dowels [5] into the drill holes (Fig. B).

Attach the mounting plate [6] using the screws [8] provided

(Fig. B).

Now place the spotlight [3] towards the mounting plate [6].

Ensure that the ball joint of the mounting plate [6] is correctly

inserted into the slot [9] of the spotlight [3]. Then, close the

ball joint cover [7] by tighten the screws clockwise (Fig. B).

Now use the holes in the mounting bracket [

]

intended for

the screws [

]

to mark the drill holes (Ø 8 mm, depth approx.

40 mm).

Ensure that you can connect the spotlight [3] using the

connection cable [

]

to the solar panel [1] .

Now drill the ﬁxing holes. Before drilling the ﬁxing holes,

ensure there are no gas, water or electrical lines that could be

drilled into or damaged in the area where you will be drilling.

Insert the dowels [

]

into the drill holes (Fig. C).

20 GB

Attach the mounting bracket [

]

using the screws [

]

.

Place the solar panel [1] into the mounting bracket [

]

(Fig. C).

Ensure that the solar panel [1] is orientated towards the sun.

Insert the plug [

]

into the socket [

]

(Fig. D).

Set the ON/OFF switch [2] on the spotlight [3] to the “ON“

position (Fig. A).

The rechargeable batteries [

]

will now charge when there is

suﬃcient solar radiation.

When selecting the mounting location for the solar panel [1], pay

attention to the following:

The solar panel [1] needs to be as directly exposed to sunlight as

possible. Even partial shading of the solar panel [1] during the

day can have a signiﬁcant inﬂuence on charging.

Cardinal direction:

Orientation towards the south is optimum. Orienta tions with slight

deviations towards the west are preferable to those with slight

deviations towards the east.

Sidan laddas...

LIVARNO 374873 Bruksanvisning

LIVARNO 374873 Bruksanvisning

på andra språk

Relaterade papper