Murray 405021x51A Användarmanual

Model No. 405021x51A

Product Type

Mfg. No. Description

7800279 40” Murray CE Riding Mower

OPERATOR’S MANUAL

Manual Part No. 7101969

Revision 00

Rev. Date 01/2008

TP 199-4811 -00-RD-R

CAUTION: Read and

follow all instructions.

2

International Pictorials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Owner’s Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Safe Operation Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . 7

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . 11

Maintenance Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Troubleshooting Chart. . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . 25

Table of Contents

en

3

4

1

2

3

5

6

9

11

12

13

4

7

8

10

IMPORTANT: The following pictori-

als are located on your unit or on

literature supplied with the prod

uct.

Before you operate the unit, learn

and understand the purpose for

each pictorial.

Safety Warning Pictorials

1

WARNING

2

IMPORTANT: Read Owner’s

Manual Before Operating This

Machine.

3

WARNING: Thrown Objects.

Keep Bystanders Away. Read

User Instructions Before Oper-

ating This Machine.

4

WARNING: Do Not Use This

Machine On Slopes Greater

Than 10 Degrees.

5

DANGER: Keep People, Espe-

cially Children, Away From

Unit.

6

DANGER: No Step.

7

DANGER: Keep Feet And

Hands Away From Rotating

Blade.

8

DANGER: Disconnect Spark

Plug Wire Before Servicing

Unit.

9

WARNING: Hot Surface.

10

WARNING: Use Caution When

Connecting Or Disconnecting

Accessories.

11

WARNING: Crushed Fingers.

12

IMPORTANT: Follow Instruc-

tions In Owner’s Manual To

Level The Deck.

13

WARNING: Stay Clear Of

Mower Blade As Long As En-

gine Is Running.

Control and Operating

Pictorials

1

Engine Start

2

Lights

3

Engine Stop

4

Engine Run

5

Engine Run

6

Brake

7

Parking Brake

8

Clutch

9

Slow

10

Fast

11

Choke

12

Oil

13

Blade Rotation Control

14

Raise

15

Fuel

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

International Pictorials

en

5

en

6

Owner’s Information

en

WARNING

Look for this symbol to indicate important safety

precautions. This symbol indicates: “Attention!

Becom

e Alert! Your Safety Is At Risk.”

Know Your Product

If you understand the unit and how the unit operates,

you will get the best performance. As you read this

manual, compare the illustrations to the unit. Learn the

location and the function of the controls. To help pre-

vent an accident, follow the operating instructions and

the safety rules. Keep this manual for future reference.

Responsibility of the Owner

WARNING

This cutting machine is capable of amputating

hands and feet and throwing objects. Failure to

observe t

he following safety instructions could

result in serious injury or death to the operator or

bystanders.

The responsibility of the owner is to follow the instruc-

tions below.

Part No. xxxxxxx

xxxxxxxxxxxxxxx

Serial No. xxxxxxxxxx

20xx

kW: x.xx

xxxx max

xxxxxxxxxxxxxxxxxxxxxxx

xxx

dB

kg: xxx

A

B

C

D

E

F

G

H

I

C

CE Identification Tag Markings

A. Manufacturer’s Identification Number

B. Manufacturer’s Serial Number

C. Power Rating in Kilowatts

D. Maximum Engine Speed in Rotations per Minute

E. Manufacturer’s Name and Address

F. Year of Manufacture

G. CE Compliance Logo

H. Mass of Unit in Kilograms

I. Guaranteed Sound Power in Decibels

7

Safe Operation Practices

en

Training

1. Read the instructions carefully. Be familiar with the

controls and the proper use of the equipment.

2. Never allow children or people unfamiliar with

these instructions to use the mower. Local

regulations may restrict the age of the operator.

3. Never mow while people, especially children, or

pets are nearby.

4. Keep in mind that the operator or user is respon-

sible for accidents or hazards occurring to other

people or their property.

5. Do not carry passengers.

6. All drivers should seek and obtain professional

and practical instruction. Such instruction should

emphasize:

a. the need for care and concentration when

working with ride-on machines;

b. control of a ride-on machine sliding on a slope

will not be regained by the application of the

brake. The main reasons for loss of control

are:

• insufficient wheel grip;

• being driven too fast;

• inadequate braking;

• the type of machine is unsuitable for its

task;

• lack of awareness of the effect of ground

conditions, especially slopes;

• incorrect hitching and load distribution.

For Ride-On (Riding) Rotary Mower

Machines

Preparation

1. While mowing, always wear substantial footwear

and long trousers. Do not operate the equipment

when barefoot or wearing open sandals.

2. Thoroughly inspect the area where the equipment

will be used and remove all objects which may

be thrown by the machine.

3. W

WARNING-Petrol is highly flammable.

a. Store fuel in containers specifically

designed for this purpose.

b. Refuel outdoors only and do not smoke while

refuelling.

c. Add fuel before starting the engine. Never

remove the cap of the fuel tank or add petrol

while the engine is running or when the engine

is hot.

d. If petrol is spilled, do not attempt to start the

engine but move the machine away from the

area of spillage and avoid creating any source

of ignition until petrol vapors have dissipated.

e. Replace all fuel tanks and container caps

securely.

4. Replace faulty silencers.

5. Before using, always visually inspect to see that

the blades, blade bolts and cutter assembly are

not worn or damaged. Replace worn or damaged

blades and bolts in sets to preserve balance.

6. On multi-blade machines, take care as rotating

one blade can cause other blades to rotate.

Operation

1. Do not operate the engine in a confined space

where dangerous carbon monoxide fumes can

collect.

2. Mow only in daylight or in good artificial light.

3. Before attempting to start the engine, disengage

all blade attachment clutches and shift into

neutral.

4. Do not use on slopes of more than 10 degrees.

5. Remember there is no such thing as a “safe”

slope. Travel on grass slopes requires particular

care. To guard against overturning:

a. do not stop or start suddenly when going up or

downhill;

b. engage clutch slowly, always keep machine in

gear, especially when travelling downhill;

c. machine speeds should be kept low on slopes

and during tight turns;

d. stay alert for humps and hollows and other

hidden hazards;

e. never mow across the face of the slope, un-

less the mower is designed for this purpose.

6. Use care when pulling loads or using heavy

equipment.

a. Use only approved drawbar hitch points.

b. Limit loads to those you can safely control.

c. Do not turn sharply. Use care when reversing.

d. Use counterweight(s) or wheel weights when

suggested in the Instruction Book.

7. Watch out for traffic when crossing or near

roadways.

8. Stop the blades rotating before crossing surfaces

other than grass.

8

Safe Operation Practices

en

9. When using any attachments, never direct

discharge of material toward bystanders nor allow

anyone near the machine while in operation.

10. Never operate the mower with defective guards or

shields, or without safety protective devices in

place.

11. Do not change the engine governor settings or

overspeed the engine. Operating an engine at

excessive speed may increase the hazard of

personal injury.

12. Before leaving the operator’s position

a. disengage the power take-off and lower the

attachments;

b. change into neutral and set the parking brake;

c. stop the engine and remove the key.

13. Disengage drive to attachments, stop the engine,

and disconnect the spark plug wire(s) or remove

the ignition key

a. before cleaning blockages or unclogging

chute;

b. before checking, cleaning or working on the

mower;

c. after striking a foreign object. Inspect the

mower for damage and make repairs before

restarting and operating the equipment;

d. if the machine starts to vibrate abnormally

(check immediately).

14. Disengage drive to attachments when transporting

or not in use.

15. Stop the engine and disengage drive to

attachment

a. before refuelling;

b. before removing the grass catcher;

c. before making height adjustment unless

adjustment can be made from the operator’s

position.

16. Reduce the throttle setting during engine run-out

and, if the engine is provided with a shut-off valve,

turn the fuel off at the conclusion of mowing.

17. Before and when backing, look behind and down

for small children.

18. Use extra care when approaching blind corners,

shrubs, trees or other objects that may obscure

vision.

Maintenance and Storage

1. On multi-blade machines, take care as rotating

one blade can cause other blades to rotate.

2. When machine will be parked, stored or left

unattended, lower the cutting means unless a

positive mechanical lock is used.

3. Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition.

4. Never store the equipment with petrol in the tank

inside a building where fumes may reach an open

flame or spark.

5. Allow the engine to cool before storing in any

enclosure.

6. To reduce the fire hazard, keep the engine,

silencer, battery compartment and petrol storage

area free of grass, leaves, or excessive grease.

7. Check the grass catcher frequently for wear or

deterioration.

8. Replace worn or damaged parts for safety.

9. If the fuel tank has to be drained, this should be

done outdoors.

9

Assembly

en

All fasteners are in the parts bag. Do not discard any

parts or material until the unit is assembled.

Install the Front Wheels

Use a knife and cut the four sides of the container. In-

stall the front wheels (1) in the container (see F

Figure 1

).

NOTE: Use a piece of wood about 4 feet (1.25 meters)

long to raise the front of the tractor. If a piece of wood

cannot be found, get another person to help lift the

tractor. Be careful, do not let the trac

tor fall.

Install the Seat

1. Carefully remove the plastic bag from the seat.

2. Align the holes in the seat hinge (2) to the holes in

the seat (1) (see F

Figure 2

). Fasten the seat to the

seat hinge with the fasteners (4) and (5).

3. Check the operating position of the seat. If the

seat needs to be adjusted, loosen the two wing

bolts (5). Slide the seat forward or backward along

the seat adjusting holes (3).Tighten the wing bolts.

Assemble the Steering Wheel

1. Make sure the front wheels point forward.

2. Slide the cover (3) over the steering post (2)

(see F

Figure 3

). Make sure the collar of the cover

is on top.

3. Slide the steering wheel (1) onto the steering post.

4. Attach the steering wheel to the steering post with

screw (4) and washer (6).

5. Some models have an optional insert (7) in the

parts bag. Attach the insert to the center of the

steering wheel.

WARNING

Before doing any assembly or maintenance to the

mower, remove the wire from the spark plug.

NOTE: In this instruction book, left and right describe

the location of a part with the operator on the seat.

1. Raise the front of the tractor. Set a support (block

of wood) under the tractor.

2. Make sure the valve stem (2) is to the outside of

the tractor. Slide the front wheel (1) on the spindle

(3).

3. Fasten each front wheel with washer (4), washer

(7) and cotter pin (5). Bend the ends of the cotter

pin apart to keep the front wheel on the spindle.

4. After the front wheels are installed, lift the

tractor from the support. Roll the tractor off of the

container.

5. If your tractor has hub caps (6), install the hub

caps. Make sure the washers hold the hub caps in

place.

(17x195)

7

(17x192)

4

5

(30x49)

6

2

3

1

Figure 1

3

2

1

5

4

Figure 2

7

4

6

1

3

2

Figure 3

10

Assembly

en

Maintenance Free Battery

IMPORTANT: Before you attach the battery cables to

the battery, check the battery date. The battery date

tells if the battery must be charged.

1. Check the top of the battery (1) for the location of

the battery date (see F

Figure 4

).

2. If the battery is put into service before the

battery cables can be attached without charging

the battery. See “Install the Battery Cables.”

3. If the battery is put into service after the battery

must be charged. See “Charge the Battery.”

Charge the Battery

WARNING

When you charge the battery, do not smoke. Keep

the battery away from any sparks. The fumes from

the ba

ttery acid can cause an explosion.

1. Remove the battery (1) and battery tray (3) (see

Figure 4

).

2. Remove the protective caps from the battery

terminals.

3. Use a 12 volt battery charger to charge the battery.

Charge at a rate of 6 amps for one hour. If you do

not have a battery charger, have an authorized

service center charge the battery.

4. Install the battery (1) and battery tray (3). Make

sure the positive (+) terminal (4) is on the left side.

Install the Battery Cables

WARNING

To prevent sparks, fasten the red cable to the

positive (+) terminal before you connect the black

cable

.

1. Remove the protective caps from the battery

terminals (see F

Figure 4

).

2. Slide the terminal cover (2) on to the red cable (5).

Fasten the red cable to the positive (+) terminal

(4) with the fasteners (6) and (7).

3. Fasten the black cable (8) to the negative (-)

terminal with the fasteners (6) and (7).

Check the Tires

Check the air pressure in the tires. Tires with too much

air pressure will cause the unit to ride rough. Also, the

wrong air pressure will keep the mower housing from

cutting level. The correct air pressure is: Front Tires

0,97 BAR (14 PSI), Rear Tires 0,69 BAR (10 PSI). The

tires were over inflated for shipment.

Check the Level of the Mower Housing

Make sure the level of cut is still correct. After you mow

a short distance, look at the area that was cut. If the

mower housing does not cut level, see the instructions

to “Level the Mower Housing” in the Maintenance sec-

tion of this instruction book.

Prepare the Engine

NOTE: The engine was shipped from the factory filled

with oil. Check the level of the oil. Add oil as needed.

See the engine manufacturer’s instructions for the type

of petrol and oil to use. Before you use the unit, read

the information on safety, operation, maintenance, and

storage.

WARNING

Follow the engine manufacturer’s instructions for

the type of petrol and oil to use. Always use a safety

petrol container. Do not smoke when adding petrol

to the engine. When inside an enclosure, do not fill

with petrol. Before you add petrol, stop the engine.

Let the engine cool for several minutes.

2

5

4

8

7

6

3

1

Figure 4

11

Operation

en

Location of Controls

Blade Rotation Control (1): Use the blade rotation

control to start and stop the rotation of the blade

(see F

Figure 5

).

Clutch/Brake Pedal (2): The pedal has two functions.

The first function is a clutch. The second function is a

brake.

Headlight Switch (3): The headlight switch is the first

part of the ignition switch. To use the lights with the en-

gine running, turn the key to the position for the lights.

Ignition Switch (3): Use the ignition switch to start and

stop the engine.

Shift Lever (4): Use the shift lever to change the speed

of the unit.

Lift Lever (5): Use the lift lever to change the height of

cut.

Parking Brake Lever (6): Use the parking brake lever to

engage the brake when you leave the unit.

Throttle Control Lever (7): Use the throttle control lever

to increase or decrease the speed of the engine.

Important! Before You Start Mowing

• Check the engine oil.

• Fill the fuel tank with petrol.

• Check the air pressure of the tires.

• Check the level of the mower housing.

• Attach the battery cables.

Attachments

This unit can use many different attachments. This unit

can pull attachments like a lawn sweeper, a lawn aera-

tor, or a hopper spreader. This unit cannot use attach-

ments that engage the ground like a plough, a disk

harrow, or a cultivator.

For trailer and pull-behind attachments, the maximum

weight is 113 kg (250 lbs).

Use the Throttle Control

Use the throttle control (7) to increase or decrease the

speed of the engine (see F

Figure 5

).

1. The FAST position is marked with a detent. For

normal operation and when using a grass bagger,

move the throttle control to the FAST position. For

maximum charging of the battery and for a cooler

running engine, operate the engine in the FAST

position.

2. The engine governor is set at the factory for

maximum performance. Do not adjust the governor

to increase the speed of the engine.

Use the Blade Rotation Control

Use the blade rotation control (1) to engage the

blade(s) (see F

Figure 5

).

1. Before you start the engine, make sure the blade

rotation control (1) is in the DISENGAGE position.

2. Move the blade rotation control to the ENGAGE

position to rotate the blade(s).

NOTE: If the engine stops when you engage the

blade(s), the seat switch is not activated. Make sure

you sit in the middle of the seat.

3. Move the blade rotation control to the DIS-

ENGAGE position to stop the blade(s). Before

you leave the operator’s position, make sure the

blade(s) has stopped rotating.

4. Before you ride the unit across a sidewalk or a

road, move the blade rotation control to the

DISENGAGE position.

WARNING

Always keep your hands and feet away from the

blade, deflector opening, and the mower housing

when the

engine runs.

2

1

3

6

7

5

4

Figure 5

12

Operation

en

Use the Shift Lever

To change the forward speed or the direction of the

unit, follow the steps below.

CAUTION

Before you move the shift lever, completely push

the clutch/brake pedal forward to stop the unit. If the

unit is not stopped, the gearbox can be damaged.

1. Completely push the clutch/brake pedal (2)

forward to stop the unit. Keep your foot on the

pedal (see F

Figure 5

).

2. Move the throttle control lever (7) to the SLOW

position.

3. To go forward, move the shift lever (4) to a forward

speed setting. To go backward, move the shift

lever to reverse.

4. Slowly release the clutch/brake pedal (2). Do not

keep your foot on the pedal.

5. Move the throttle control (7) to the FAST position.

Use the Parking Brake

1. Completely push the clutch/brake pedal (2) for-

ward (see F

Figure 5

).

2. Lift the parking brake lever (6).

3. Remove your foot from the clutch/brake pedal

and then release the parking brake lever. Make

sure the parking brake will hold the unit.

4. To release the parking brake, completely push

the clutch/brake pedal (2) forward. The parking

brake will automatically release.

WARNING

Before you leave the operator’s position, move the

shift lever to the neutral (N) position. Set the

parking brake. Move the blade rotation control to

the DISENGAGE position. Stop the engine and

remove the ignition key.

Change the Cutting Height

To change the cutting height, raise or lower the lift lever

(5) as follows (see F

Figure 5

).

1. Move the lift lever forward to lower the mower

housing and back to raise the mower housing.

2. When you ride on a sidewalk or road, move the lift

lever to the highest position and move the blade

rotation control to the DISENGAGE position.

Stop the Unit

1. Completely push the clutch/brake pedal (2)

forward to stop the unit. Keep your foot on the

pedal (see F

Figure 5

).

2. Move the blade rotation control (1) to the DIS-

ENGAGE position.

3. Move the shift lever (4) to the NEUTRAL position.

4. Set the parking brake (6).

WARNING

Make sure the parking brake will hold the unit.

5. Move the throttle control (7) to the SLOW position.

6. To stop the engine, turn the ignition key (3) to the

OFF position. Remove the key.

Transport the Unit

To transport the unit, follow the steps below.

1. Move the blade rotation control to the

DISENGAGE position.

2. Raise the lift lever to the highest position.

3. Move the throttle control to a position between

SLOW and FAST.

4. To go faster, move the shift lever to a faster speed.

13

Operation

en

Operate with the Mower Housing

IMPORTANT: When you operate with the mower hous-

ing, always operate with the throttle control in the FAST

position.

1. Start the engine.

2. Move the lift lever to a height of cut position. In

high or thick grass, cut the grass in the highest

position first and then lower the mower housing to

a lower position.

3. Move the throttle control to the SLOW position.

4. Slowly move the blade rotation control to the

ENGAGE position.

5. Push the clutch/brake pedal completely forward.

6. Move the shift lever to one of the speed settings.

NOTE: When you mow in heavy grass or mow with a

bagger, put the shift lever in the slowest speed.

7. Slowly release the clutch/brake pedal.

8. Move the throttle control to the FAST position. If

you need to go faster or slower, stop the unit

and move the shift lever to another speed setting.

9. Make sure the level of cut is still correct. After you

mow a short distance, look at the area that was

cut. If the mower housing does not cut level, see

the instructions to “Level the Mower Housing” in

the Maintenance section.

WARNING

For better control of the unit, select a safe speed.

Operate on Hills

WARNING

Do not ride up or down slopes that are too steep to

back straight up. Never ride the unit across a slope.

1. Before you ride up or down a hill, move the shift

lever to the slowest speed.

2. Do not stop or change speed settings on a hill. If

you must stop, quickly push the clutch/brake pedal

forward and set the parking brake.

3. To start again, make sure the shift lever is in the

slowest speed. Move the throttle control to the

SLOW position. Slowly release the pedal.

4. If you must stop or start on a hill, always have

enough space for the unit to roll when you release

the brake and engage the clutch.

5. Be very careful when you change directions on a

hill. When on a slope or in a turn on a hill, move the

throttle control to the SLOW position to help

prevent an accident.

Before Starting the Engine

Check the Oil

NOTE: The engine was shipped from the factory filled

with oil. Check the level of the oil

. Add oil as needed.

See the engine manufacturer’s instructions for the type

of petrol and oil to use.

1. Make sure the unit is level.

NOTE: Do not check the level of the oil while the en-

gine runs.

2. Check the oil. Follow the procedure in the engine

manufacturer’s instructions.

3. If necessary, add oil until the oil reaches the FULL

mark on the dipstick. The quantity of oil needed

from ADD to FULL is shown on the dipstick. Do not

add too much oil.

Add Petrol

WARNING

Always use a safety petrol container. Do not smoke

when adding petrol to the fuel tank. Do not add

petr

ol when you are inside an enclosure. Before you

add petrol, stop the engine and let the engine cool

for several minutes.

Fill the fuel tank (1) to the FULL (2) position with regu-

lar unleaded petrol (see F

Figure 6

). Do not use premium

unleaded petrol. Make sure the petrol is fresh and

clean. Leaded petrol will increase deposits and shorten

the life of the valves.

2

1

Figure 6

14

Operation

en

Start the Engine

3. Every time you use the unit, check the blade. If the

blade is bent or damaged, immediately replace the

blade. Also, make sure the nut for the blade is

tight.

4. Keep the blade(s) sharpened. Worn blades will

cause the ends of the grass to turn brown.

5. Do not cut or bag grass that is wet. Wet grass will

not discharge correctly. Let the grass dry before

cutting.

6. Use the left side of the mower housing to trim near

an object.

7. Discharge the cut grass onto the mowed area. The

result is a more even discharge of cut grass.

8. When you mow large areas, start by turning to the

right so that the cut grass will discharge away from

shrubs, fences, driveways, etc. After one or two

rounds, mow in the opposite direction making left

turns until finished.

9. If the grass is very high, cut two times to decrease

the load on the engine. First cut with the mower

housing in the highest position and then lower the

mower housing for the second cut.

10. For better engine performance and an even

discharge of the cut grass, always operate the

engine with the throttle in FAST position.

11. When you use a bagger, operate the engine with

the throttle in FAST position and the shift lever in

first or second gear.

12. For better cutting performance and a quality cut,

mow with the shift lever in one of the slower

speeds.

13. After each use, clean the bottom and top of the

mower housing for better performance. Also, a

clean mower housing will help prevent a fire.

WARNING

The electrical system has an operator presence

system that includes a sensor switch for the seat.

These components tell the electrical system if the

operator is sitting on the seat. This system will stop

th

e engine when the operator leaves the seat. For

your protection, always make sure this system

operates

correctly.

NOTE: The engine will not start unless you depress the

clutch/brake pedal and move the blade rotation control

to the DISENGAGE position.

1. Push the clutch/brake pedal completely forward.

Keep your foot on the pedal.

2. Move the shift lever to the neutral (N) position.

3. Make sure the blade rotation control is in the

DISENGAGE position.

4. Move the throttle control completely forward to the

CHOKE or FAST position. Some models have a

separate choke knob. Pull the choke knob to the

full CHOKE position.

5. Turn the ignition key to the START position.

NOTE: If the engine does not start after four or five

tries, move the throttle control to the FAST pos

ition.

Again try to start the engine. If the engine will not start,

see the TROUBLESHOOTING CHART.

6. Slowly move the throttle control to the SLOW

position.

7. To start a hot engine, move the throttle control to a

position between FAST and SLOW.

Mowing and Bagging Tips

1. For a lawn to look better, check the cutting level of

the mower housing. See “Level the Mower

Housing” in the Maintenance section.

2. For the mower housing to cut level, make sure the

tires have the correct amount of air pressure.

15

Maintenance Chart

en

Frequency Maintenance Required Comments

Daily or before each use Maintenance engine. Refer to the Engine Owner’s

Manual.

Examine blade(s). Check for cracks, wear, and exces-

sive damage.

Remove debris from unit and moving

parts.

Examine all rotating and sliding parts.

Check tire inflation. Refer to the Maintenance section.

Verify that the mower housing is level. Refer to the Maintenance section.

Examine V-belts. Check for cracks, wear, and exces-

sive damage.

Check brake operation. Refer to the Engine Owner’s Manual.

After completion of first

5 hours

Change oil. Refer to the Engine Owner’s Manual.

After 25 hours Maintenance engine. Refer to the Maintenance section.

Remove, examine, sharpen, and

balance blade(s).

Refer to the Maintenance section.

Check adjustments:

a. Blade Rotation Control

b. Brake

c. Clutch

d. Steering.

Refer to the Maintenance section.

Lubricate chassis and mower

housing.

Refer to Where to Lubricate

instructions.

Check the muffler:

a. Torque

b. For wear or burn out

c. Condition of spark arrester

(if applicable).

Refer to the Maintenance section.

Before storage of 30 days or

more

Prepare engine for storage. Refer to the Engine Owner’s

Manual.

Drain fuel system. Refer to Warnings in Owner’s

Manual.

Add fuel stabilizer. Refer to the Engine Owner’s

Manual.

Prepare battery for storage:

a. Remove from unit.

b. Fully charge.

c. Move to cool dry place.

16

Maintenance

en

General Recommendations

1. The owner’s responsibility is to maintain this

product. This will extend the life of the product

and is also necessary to maintain warranty

coverage.

2. Check the spark plug, drive brake, lubricate the

unit, and clean the air filter once a year.

3. Check the fasteners. Make sure all fasteners are

tight.

4. Follow the Maintenance section to keep the unit in

good operating condition.

WARNING

Before you make an inspection, adjustment, or

repair to the unit, disconnect the wire to the spark

plug. Remove the wire from the spark plug to

prevent the engine from starting by accident.

NOTE: Torque is measured in foot pounds (metric Nm).

This measurement describes how tight a nut or bolt

must be.The torque is measured with a torque wrench.

Inspect the Blade

WARNING

Before you inspect or remove the blade, disconnect

the wire to the spark plug. If the blade hits an

obj

ect, stop the engine. Check the unit for damage.

The blade has sharp edges.When you hold the

blade, use gloves or cloth material to protect your

hands.

If you keep the blade (1) sharp and inspect the blade

for damage, the blade will cut better and be more safe

to operate (see F

Figure 7

). Frequently check the blade

for excessive wear, cracks,or other damage.

Frequently check the nut (3) that holds the blade (1).

Keep the nut (3) tight. If the blade hits an object, stop

the engine. Disconnect the wire to the spark plug. See

if the blade is bent or damaged. Check the blade

adapter (5) for damage.

Before you operate the unit, replace damaged parts

with original equipment parts. See the authorized serv-

ice center in your area. Every three years, have an au-

thorized service person inspect the blade or replace

the old blade with an original equipment part.

Remove and Install the Blade

1. Remove the mower housing. See the instructions

to “Remove the Mower Housing.”

2. Use a piece of wood to keep the blade from

rotating.

3. Remove the nut (3) that holds the blade (1) (see

Figure 7

).

4. Check the blade and the blade adapter (5)

according to the instructions for “Inspect Blade.”

Replace a badly worn or damaged blade with an

original equipment blade. See an authorized

service center in your area.

5. Clean the top and bottom of the mower housing.

Remove all the grass and debris.

6. Mount the blade and blade adapter (5) on the

mandrel (6).

7. Mount the blade so that the hi-lift edges (7) are

up. If the blade is upside down, the blade will not

cut correctly and can cause an accident.

8. Fasten the blade with the original washers and

nut (3). Make sure the outside rim of the Belleville

washer (2) is against the blade.

WARNING

Always keep the nut (3) tight that holds the blade

(1). A loose nut or blade can cause an accident.

9. Tighten the nut (3) that holds the blade to a

torque of 30 foot pounds (41,5 Nm).

10. Install the mower housing. See “Remove the

Mower Housing.”

6

5

4

3

2

7

1

Figure 7

17

Maintenance

en

Adjust the Blade Rotation Control

WARNING

To prevent an injury, the blade rotation control must

operate correctly.

In normal usage, the blade rotation control will not re-

quire an adjustment. However, it the cutting perform-

ance decreases or the quality of cut is poor, make the

following changes.

1. When you mow, make sure the throttle control is in

the FAST position.

2. Move the blade rotation control to the DIS-

ENGAGE position (1) (see F

Figure 8

).

3. Stop the engine. Disconnect the wire from the

spark plug.

4. Check the blade(s). Keep a sharp edge on the

blade(s). A blade that is not sharp will cause the

tips of the grass to become brown.

5. Disconnect the blade drive spring (2) from the

blade control rod (1) (see F

Figure 9

). Move the

blade drive spring (2) to the middle hole (4). This

will increase the tension on the mower drive belt.

6. Attach the wire to the spark plug. Mow for a short

distance and again check the quality of cut. If

necessary, move the blade drive spring (2) to the

bottom hole (5).

7. Again check the quality of cut. If the quality of cut

has not improved, replace the mower drive belt.

See ”Replace the Mower Drive Belt.” If replacing

the belt does not correct the problem, take the unit

to an authorized service center.

8. Move the blade rotation control to the DIS-

ENGAGE position. Stop the engine.

9. Check the operation of the blade brake. Rotate the

pulleys with your hand. Make sure the brake pads

(7) are pressed tightly against the pulleys (see

Figure 10

).

WARNING

If the brake pads (7) do not press tightly against the

pulleys, take the unit to an authorized service

center.

10. Move the blade rotation control to the ENGAGE

position (2) (see F

Figure 8

).

11. Check the pads for the blade brake (7) (see

Figure 10

). If the pads are excessively worn or

damaged, replace the brake pad assemblies.

Correct replacement parts and assistance are

available from an authorized service center.

2

1

Figure 8

2

1

4

3

5

Figure 9

1

7

4

5

4

6

3

2

Figure 10

18

12. Attach the wire to the spark plug. Mow for a short

distance and again check the operation of the

blade rotation control.

13. When you move the blade rotation control to the

DISENGAGE position, all movement will stop

within five seconds. If there is movement of the

belt or the blades continue to rotate, engage and

disengage the blade rotation control five times to

remove any excess rubber from a new mower

drive belt. If you need assistance, take the unit to

an authorized service center.

14. If you replace the mower drive belt, move the

blade drive spring (2) to the top hole (3) (see

Figure 9

).

Maintenance

en

Adjust the Shift Lever

If the NEUTRAL position on the shift lever does not

match neutral on the gearbox, adjust the shift lever as

follows.

1. Stop the engine.

2. Disconnect the adjuster nut (2) from the shifter

bracket (3) (see F

Figure 18

).

3. Make sure the shift lever is in the NEUTRAL

position.

4. Push the unit forward. Make sure the gearbox is in

neutral.

5. To align the adjuster nut with the hole in the

shifter bracket, turn the adjuster nut.

6. Connect the adjuster nut to the shifter bracket.

7. Make sure the NEUTRAL position on the shift lever

matches neutral on the gearbox.

Check and Adjust the Clutch

If the motion drive belt is loose, the clutch will slip

when; going up a hill, pulling a heavy load, or the unit

will not move forward. Adjust the clutch as follows.

WARNING

Before you make an inspection, adjustment, or

repair to the unit, disconnect the wire to the spark

plug

. Remove the wire from the spark plug to

prevent the engine from starting by accident.

1. Check the routing of the motion drive belt. Make

sure the belt is installed correctly and is inside all

the belt guides.

2. Remove the cotter pin (1), washer (2), and brake

spring (3) from the adjustable nut (4) (see F

Figure

11

).

3. Disconnect the adjustable nut from the brake

lever assembly (5) and the parking brake latch (6).

4. Align the hole in the brake lever (5) with the hole

in the frame. Hold the brake lever in place with a

6 mm pin or bolt (7).

5. Pull the clutch rod forward until tight. Turn the

adjustable nut until the nut will fit through the

hole in the brake lever.

6. Assemble the adjustable nut to the parking brake

latch, brake lever and brake spring. Fasten with

the washer (2) and cotter pin (1).

7. Remove the 6 mm pin or bolt.

8. If the belt still slips after the clutch has been

adjusted, then the motion drive belt is worn or

damaged and must be replaced. See “Replace the

Motion Drive Belt.”

Check and Adjust the Drive Brake

Completely push the clutch/brake pedal forward. Set

the parking brake. Move the shift lever to the neutral

(N) position. Push the unit. If the rear wheels rotate, ad-

just or replace the brake pads. Adjust the drive brake

as follows.

1. The location of the drive brake (1) is on the right

side of the gea rbox (3) (see F

Figure 12

).

2. Make sure the parking brake is set and the shift

lever is in neutral (N). Turn the hex nut (2) in a

clockwise direction until the rear wheels do not

turn when the unit is pushed forward.

6

4

2

3

1

5

7

Figure 11

19

3. Release the parking brake and push the unit. If the

unit does not roll, turn the hex nut (2) in a counter-

clockwise direction until the unit rolls.

4. Set the parking brake. Push the unit. If the rear

wheels do not turn, the drive brake (1) is correctly

adjusted. Release the parking brake.

Maintenance

en

WARNING

If you cannot correctly adjust the drive brake,

replace the brake pads. Correct replacement parts

and a

ssistance are available from an authorized

service center.

Remove the Battery

To charge or clean the battery (1), remove the battery

from the unit as follows (see F

Figure 4

).

WARNING

To prevent sparks, disconnect the black battery

cable (8) from the negative (-) terminal before you

dis

connect the red cable (5).

WARNING

The battery contains sulphuric acid which is

harmful to the skin, eyes and clothing. If the acid

gets o

n the body or clothing, wash with water.

1. Disconnect the black cable (8) from the negative

(-) terminal.

2. Disconnect the red cable (5) from the positive (+)

terminal (4).

3. Lift the battery tray (3) and the battery (1) out of the

unit.

Charge the Battery

WARNING

When you charge the battery, do not smoke. Keep

the battery away from any sparks. The fumes from

the ba

ttery acid can cause an explosion.

WARNING

To prevent sparks, fasten the red cable to the

positive (+) terminal before you connect the black

cable

.

1. Before you charge the battery (1), remove the

battery (see F

Figure 4

).

2. To charge the battery, use a 12 volt battery

charger. Charge at a rate of 6 amps for 1 hour.

3. Install the battery.

4. Fasten the red cable (5) to the positive (+) terminal

(4) with the fasteners as shown.

5. Fasten the black cable (8) to the negative (-)

terminal with the fasteners as shown.

Level the Mower Housing

If the mower housing is level, the blade will cut easier

and the lawn will look better.

WARNING

Before you make an inspection, adjustment, or

repair to the unit, disconnect the wire to the spark

plug

. Remove the spark plug wire to prevent the

engine from starting by accident.

1. Make sure the unit is on a hard flat surface.

2. Check the air pressure in the tires. If the air

pressure is incorrect, the mower housing will not

cut level. Make sure the tires are inflated to: Front

Tires 0,97 BAR (14 PSI), Rear Tires 0,69 BAR

(10 PSI).

3. Move the lift lever (1) to the lowest cut position (2)

(see F

Figure 13

).

WARNING

The lifter lever (3) is spring loaded. Make sure the

lift lever (3) is locked in the lowest cut position (2).

2

3

1

Figure 12

20

Maintenance

en

4. Loosen the left and right adjuster knobs (1) (see

Figure 14

). Push down on each side of the mower

housing. Make sure both sides of the mower

housing are setting on a flat surface. Also, make

sure the lift links are loose and can easily move up

or down.

5. Push down on the lift links (2) and tighten the left

and right adjuster knobs. Make sure the adjuster

knobs are tight. If necessary, use a wrench to

tighten the adjuster knobs.

6. Raise the lift lever (1) (see F

Figure 13

).

7. Mow for a short distance. If the height of cut is not

level, repeat the above steps.

Where to Lubricate

M

Models with grease fittings: Lubricate with

grease gun (see Figure 15).

Apply grease with a brush to th

e areas

shown.

Lubricate the areas shown with engine oil.

NOTE: Apply grease to the steering gear assemb

ly.

CAUTION: If the unit is operated in dry areas that have

sand, use a dry graphite spray to lubricate

the unit.

Figure 15

Check the Tires

Check the air pressure in the tires. Tires with too much

air pressure will cause the unit to ride rough. Also, the

wrong air pressure will keep the mower housing from

cutting level. The correct air pressure is: Front Tires

0,97 BAR (14 PSI), Rear Tires 0,69 BAR (10 PSI).

2

1

Figure 13

2

1

Figure 14

Sidan laddas ...

Murray 405021x51A Användarmanual

Denna manual är också lämplig för

Murray 405021x51A Användarmanual

på andra språk

Relaterade papper

Andra dokument