Yamaha NX-SW10 Användarmanual
- Kategori
- Kompletterande musikutrustning
- Typ
- Användarmanual
Denna manual är också lämplig för
OWNER’S MANUAL
MODE D’EMPLOI
MANUAL DE INSTRUCCIONES
NX-SW10
Subwoofer/Center Speaker/Rear Speakers
Caisson de grave/Enceinte centrale/
Enceintes arriere
UCA
CAUTION
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accor-
dance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or
the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the manufac-
turer, or sold with the apparatus. When a
cart is used, use caution when moving the
cart/apparatus combination to avoid injury
from tip-over.
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
dropped.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert you to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the presence
of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION
INTRODUCTIOIN
PREPARATIONS
PLAYBACK
SETUP MENU APPENDIX
English
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring
or distortion – and, most importantly, without affecting your
sensitive hearing.
FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC,
to use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation instruc-
tions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regula-
tions, Part 15 for Class “B” digital devices. Compliance
with these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF”
and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line filter/
s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300
ohm ribbon lead, change the lead-in to coaxial type
cable.
If these corrective measures do not produce satisfac-
tory results, please contact the local retailer autho-
rized to distribute this type of product. If you can not
locate the appropriate retailer, please contact Yamaha
Electronics Corp., U.S.A. 6660 Orangethorpe Ave,
Buena Park, CA 90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
IMPORTANT SAFETY INSTRUCTIONS
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume
levels.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
CAUTION
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install the speakers in a cool, dry, clean place – away
from windows, heat sources, sources of excessive
vibration, dust, moisture and cold. Avoid sources of
humming (transformers, motors). To prevent fire or
electrical shock, do not expose the speakers to rain
or water.
3 To prevent the enclosure from warping or
discoloring, do not place the speakers where they
will be exposed to direct sunlight or excessive
humidity.
4 Do not place the speakers where they are liable to be
knocked over or struck by falling objects. Stable
placement will also ensure better sound
performance.
5 Avoid installing the speakers in a place where foreign
objects and liquid might fall. It might cause a fire,
damage to the speakers and/or personal injury. Do
not place the following objects on the speakers:
• Other components, as they may cause damage and/
or discoloration on the surface of the speakers.
• Burning objects (i.e., candles), as they may cause
fire, damage to the speakers and/or personal injury.
• Containers with liquid in them, as they may cause
an electrical shock to the user and/or damage to the
speakers.
6 Placing the speakers on the same shelf or rack as the
turntable can result in feedback.
7 Any time you note distortion, reduce the volume
control on your amplifier to a lower setting. Never
allow your amplifier to be driven into “clipping”.
Otherwise the speakers may be damaged.
8 As these speakers contain strong magnets (though
all of them are magnetically shielded types), avoid
placing watches, magnetic tapes, etc. near them.
Also, placing the speakers near a TV set may impair
picture color. If this happens, move the speakers
away from the TV set.
9 Do not attempt to clean the speakers with chemical
solvents as this might damage the finish. Use a clean,
dry cloth.
10 Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before
concluding that the unit is faulty.
11 Secure placement or installation is the owner’s
responsibility.
YAMAHA shall not be liable for any accident caused
by improper placement or installation of speakers.
■ For SW-VS10
12 Never open the cabinet. If something drops into the
set, contact your dealer.
13 Do not use force on switches, controls or connection
wires. When moving the unit, first disconnect the
power plug and the wires connected to other
equipments. Never pull the wires themselves.
14 When not planning to use this unit for a long period
(ie., vacation, etc.), disconnect the AC power plug
from the wall outlet.
15 To prevent lightning damage, disconnect the AC
power plug when there is an electric storm.
16 Since this unit has a built-in power amplifier, heat will
radiate from the rear panel. Place the unit apart from
the walls, allowing enough space above, behind and
on the both sides of the unit to prevent fire or
damage. Furthermore, do not position with the rear
panel facing down on the floor or other surfaces.
Be sure to allow a space of at least 10 cm above,
behind and on both sides of the unit.
17 Super-bass frequencies reproduced by this unit may
cause a turntable to generate a howling sound. In
such a case, move this unit away from the turntable.
18 If you hear distorted noise (i.e., unnatural,
intermittent “rapping” or “hammering” sounds)
coming from this unit, reduce the volume level.
Extremely loud playing of a movie soundtrack’s low
frequency, bass-heavy sounds or similarly loud
popular music passages can damage this speaker
system.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
■ For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note
The plug severed from the mains lead must be destroyed, as a plug
with bared flexible cord is hazardous if engaged in a live socket
outlet.
■ SPECIAL INSTRUCTIONS FOR U.K.
MODEL
IMPORTANT:
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug, proceed
as follows: The wire which is coloured BLUE must be
connected to the terminal which is marked with the letter
N or coloured BLACK. The wire which is coloured
BROWN must be connected to the terminal which is
marked with the letter L or coloured RED. Making sure
that neither core is connected to the earth terminal of the
three pin plug.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
English
FEATURES
● Home Theater Sound
Connecting this system to the VS-10 (sold separately)
allows you to enjoy the power of low bass sounds
plus surround effects.
● Centralized Control with the VS-10
(sold separately)
The VS-10 is used to do things such as adjust the
subwoofer level and adjust the speaker level using test
tones. Refer to the VS-10 (sold separately) owner’s
manual.
● Advanced YST v
This subwoofer incorporates advanced YAMAHA
Active Servo Technology to achieve superior bass
reproduction.
CONTENTS
Wing nuts (x 2)
Screws (x 2)Type B brackets (x 2)Type A brackets (x 2)
(wall brackets)
Speaker mounting brackets
System connector cable
(3 m x 1)
Speaker cords
(Used for the rear speakers: 15 m x 2)
Checking the Package Contents
Check that the following accessories are included in the package.
y indicates a tip for your operation.
FEATURES .................................................................. 1
SPEAKER PLACEMENT .......................................... 2
CONNECTIONS.......................................................... 3
INSTALLATION OF THE CENTER SPEAKER .... 6
INSTALLATION OF THE REAR SPEAKERS ....... 7
TROUBLESHOOTING .............................................. 9
SPECIFICATIONS.................................................... 10
Velcro strips (x 2)
(Used for the center speaker: 4 m x 1)
2
■ Subwoofer (SW-VS10)
Place the subwoofer at the outside of the either right or left
main speaker and turn it slightly toward the center of the
room to reduce the wall reflections. Try altering the position
of the subwoofer versus the listening position as the relative
position will affect the way the bass sounds.
■ Rear speakers (NX-VS10E)
Depending on room conditions, it is possible to place
YAMAHA rear speakers NX-VS10E on shelves or hang
them on the wall. For the installation of the rear speakers,
refer to page 7.
Speakers should be placed about 1.5 m above the floor
when you sit on the floor, or about 1.8 m above the floor
when you sit on the chair.
■ Center speaker (NX-VS10C)
Place the center speaker on top of the television and align
the front surface of the speaker with the front surface of the
television monitor. For the installation of the center
speakers, refer to page 6.
If the speaker cannot be placed on top of the television,
place it on a rack beneath the television as close to the
television monitor as possible.
■ YAMAHA main speakers NX-VS10M
(sold separately)
Place the main speakers an equal distance from each side of
the TV monitor.
Placing the main speakers at almost the same height as your
listening position is more effective.
CAUTION
Although this center speaker is magnetically shielded,
this may still affect the color on the television monitor
when using the speaker near the television. Adjust the
relative positions of the speaker and the television if this
happen. Perform the following steps if you are using a
magnetically shielded television.
1 Turn off the television.
2 Wait awhile and turn the television back on.
About 1.8 m
1.5 - 1.8 m
Right rear
speaker
Rear speakers
Place behind or to the sides of the listening position.
Left rear
speaker
Subwoofer
Place near the right or left main speaker.
Center speaker
Place above the TV monitor in the center.
SPEAKER PLACEMENT
Main speakers (sold separately)
Place each side of the TV monitor.
About 1.5 m
When sitting on the floor. When sitting on the chair.
3
English
CAUTION
Always be sure to turn off the power of any component to be connected when making connections.
To ensure proper connections
• Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some
components require different connection methods and have different terminal names. Refer to the instructions for each
component to be connected to this unit.
Connecting the Center Speaker and the Rear Speakers to the Subwoofer
Note
• Do not connect any speakers to the speaker terminals on the subwoofer except for the supplied center speaker (NX-VS10C) and rear
speakers (NX-VS10E). Damage may result if a different speaker is connected.
y
Remove the plastic insulation from the ends of the speaker cords and twist the bare wires. (The bare wire will stay neat if you twist while
removing the plastic insulation.)
CONNECTIONS
+– +–
+–
+
–
+
–
REAR, CENTER SPEAKERS
DO NOT CONNECT THIS UNIT TO
SPEAKERS OTHER THAN NX-VS10E,
NX-VS10C
REAR R
CENTER
REAR L
Speaker cord
identification label
Speaker cord
identification label
Right rear speaker
Center speaker
Left rear speaker
The rear panel of the subwoofer
4
1
22
3
1
2
3
1 Hold down the tab.
2 Insert the bare wire of the speaker cord into
the hole.
3 Release the tab. (The tab will return to its
original position when you release your
finger.)
• Connect the line-in cord to the + terminals (red) on the
right, and the other cord to the – terminals (black) on the
left.
• Once connected, pull gently on the speaker cords to
check that they are connected securely.
Bare wire
Tab
■ Connecting the speaker cords to the speaker terminals on the center
speaker and the rear speakers
1 Open the tab for the + terminal (red) or the –
terminal (black).
2 Insert the bare wire of the speaker cord into
the hole.
3 Return the tab until it clicks.
• Connect the line-in cord to the + terminal (red), and the
other cord to the – terminal (black).
• Once connected, pull gently on the speaker cords to
check that they are connected securely.
CAUTIONS
• Do not let the bare speaker wire touch each other and
do not let them touch any metal part of the speakers.
This could damage the speakers.
• Do not mistakenly connect positive (+) to negative(–)
or vice versa when connecting speaker cords.
• Insert the speaker cords securely so that positive (+)
and negative (–) do not short. The speaker may not
output any sound or may output noise, causing damage
to the speakers, if speaker cords are not inserted
securely.
• Only insert the bare wire portion of the speaker cords
into the holes. Sound will not be output if you insert as
far as the plastic insulation part of the cord.
• Secure the speaker cords so that they will not catch on
hands or feet.
Bare wire
Tab
■ Connecting the speaker cords to the speaker terminals on the subwoofer
CONNECTIONS
5
English
DIGITAL 1
(V/PCM)
VIDEO 1 TV
VIDEO SIGNAL
INPUT
MAIN SPEAKERS
SUBWOOFER
OUT
MONITOR
OUT
SYSTEM
CONNECTOR
MARK
DO NOT CONNECT THIS UNIT TO
SPEAKERS OTHER THAN NX-VS10M
+
–
+
–
+
–
+
–
REAR, CENTER SPEAKERS
SYSTEM
CONNECTOR
MARK
DO NOT CONNECT THIS UNIT TO
SPEAKERS OTHER THAN NX-VS10E,
NX-VS10C
To an AC outlet
Once all connections have been made, check them one more
time. Finally, insert the plug of the AC power supply cord of
the subwoofer into an AC outlet.
Notes
• Do not scratch, forcibly bend, or pull the system connector cable as this may damage the cable, causing loss of audio output, and possibly
result in fire or electric shock. Take particular care that the cable is not squashed by a rack or caster.
• When you disconnect the plug of the AC power supply cord of the subwoofer, turn off the power of the VS-10 beforehand.
• When you use only the VS-10 (sold separately) without using this system, disconnect the plug of the AC power supply cord of the
subwoofer and the system connector cable beforehand.
y
• When the power of the VS-10 is turned off, that of the subwoofer is also turned off accordingly.
Connecting the AC Power Supply Cord
Match the mark on the plug
with the mark on the terminal
and insert.
To SYSTEM
CONNECTOR terminal
Supplied
system
connector
cable
To SYSTEM
CONNECTOR
terminal
VS-10 (sold separately)
Connecting the Subwoofer to the VS-10
Connect the SYSTEM CONNECTOR terminal on the VS-10 (sold separately) to the SYSTEM CONNECTOR terminal on
the subwoofer using the system connector cable.
Match the mark on the plugs with those on the terminals and insert the plugs.
+
–
+
–
REAR, CENTER SPEAKERS
SYSTEM
CONNECTOR
MARK
DO NOT CONNECT THIS UNIT TO
SPEAKERS OTHER THAN NX-VS10E,
NX-VS10C
MAINS
CONNECTIONS
6
Note
• Once the center speaker is secured in this way, the paint on the
television surface used for installation may peel off when velcro
strip is removed later. Be sure to apply velcro strip after carefully
checking the surface to be used for installation.
Press down.
4 Align both the velcro strips on both sides and
firmly press downward on the top of the center
speaker.
Smooth surface
Peel off the
seal.
3 Peel off the seal of the velcro strip with the
smooth surface and apply to the positions
determined in step 2.
2 Place the center speaker where it is to be
installed (ex. on top of the television ) to
determine where to apply the velcro strip with
the smooth surface.
Determine the velcro strips position on the television so
that the velcro strips should be matched with those of
the center speaker.
Center speaker
(bottom panel)
Rough surface
1 Peel off the seal of the velcro strip with the
rough surface and apply to the appropriate
positions as shown in the illustration below.
INSTALLATION OF THE CENTER SPEAKER
To prevent the center speaker from falling, secure it with the supplied velcro strips when placing it on a television or other
device.
Using the Velcro Strips
Precautions before installation
• Do not touch the adhesive surface after peeling off the strip as this will weaken its adhesive strength.
• Thoroughly wipe clean the surface where the velcro strip is to be applied. Note that adhesive strength is weakened if the
surface is dusty, oily or wet and that this may cause the center speaker to drop.
+
–
Peel off the
seal.
7
English
Note
• After mounting, check that the speakers are attached securely.
20 mm or more
7 mm
70 mm
70 mm
Wood screws having a diameter of about 4
to 5 mm (commercially available)
■ Mounting speakers directly on the
wall
It is possible to hang the speakers directly on the wall
without using the type A brackets by attaching two wood
screws on the wall and then using the holes on the rear
panel of the speakers for direct attachment.
3 Adjust the angle of the speaker and then
tighten the wing nut.
Wing nut (supplied)
2 Attach the speaker to the bracket using the
supplied wing nut.
Type A bracket
20 mm or more
65 mm
1 Attach two commercially available wood
screws (diameter about 4 mm) in the location
on the wall where the rear speaker is to be
hung, and then mount the type A bracket on
the wood screws.
Check that the wood screws are secure inside the
narrow portion of the holes in the bracket.
INSTALLATION OF THE REAR SPEAKERS
Use the supplied type A wall brackets when hanging the rear speakers on a wall.
8
CAUTIONS
Be sure to read these important precautions.
• Each speaker weighs approximately 0.7 kg. Select a
firm wall or pillar to attach screws to. Do not attach
screws to material such as mortar or veneer as screws
may come loose easily, causing the speaker to fall.
• Do not mount speakers using nails or tape as
vibrations during operation may cause nails to come
loose or tape to peel off, causing the speaker to fall.
• Take care that the speaker cord is not pinched between
the speaker and the bracket. Be sure that the speaker
cord passes through the groove on the rear panel of the
speaker.
• Secure the speaker cords so that they will not catch on
hands or feet, causing speakers to drop.
• Be absolutely sure to check for safety after speakers
are mounted. YAMAHA bears no responsibility for
damage caused due to improper installation or
installation in an improper location.
60 mm
2 Mount the speaker on the speaker stand using
the bracket holes (spaced at 60 mm).
Be sure to prepare the small screws (diameter: 4 mm,
length: 8 mm), spring washers and washers.
Type B bracket
Supplied screw
1 Attach the type B bracket to the bottom of the
speakers using the supplied screws.
Align so that the protrusion on the bracket goes into the
groove on the bottom of the speaker.
Using Commercially Available Speaker Brackets (distance between screw
holes: 60 mm)
INSTALLATION OF THE REAR SPEAKERS
9
English
No sound from the center
speaker or the rear speakers.
• Is the AC power supply cord connected?No sound at all.
5
• Hum caused by external electromagnetic waves may be generated.
Try inverting the right-left polarity of the power cord and re-insert into
the AC outlet.
A “humming” noise is present.
• Is DOLBY PRO LOGIC selected for a monaural source on the VS-10 ?
Refer to the owner’s manual for the VS-10 (sold separately).
• Is VIRTUAL SURROUND selected on the VS-10? Refer to the owner’s
manual for the VS-10 (sold separately).
• Is the center speaker level or the rear speaker level of the VS-10 set too
low for the test tone? Refer to the owner’s manual for the VS-10 (sold
separately).
• Are the speaker cords connected correctly?
• Is the subwoofer level of the VS-10 set too low? Refer to the owner’s
manual for the VS-10 (sold separately).
• Is the system connector cable connected correctly?
No sound from the subwoofer.
• Is the INPUT selector of VS-10 set correctly? Refer to the owner’s
manual for the VS-10 (sold separately).
• Is the sound from the VS-10 temporarily muted? Refer to the owner’s
manual for the VS-10 (sold separately).
TROUBLESHOOTING
Be sure to investigate thoroughly before requesting repairs or after service. If it cannot be corrected, or if the problem is not
listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center.
Notes
• Sometimes the system may cease to recognize operations due to a mistaken operation or as a result of strong external noise (such as
irregular voltage due to shock of impact, excessive static electricity, or lightning strike). If this happens, first disconnect the power cord,
wait about 30 seconds, re-connect the power cord, and try the desired operation again.
• When requesting repairs or after service, be sure to bring along with the VS-10 (sold separately).
SYMPTOM CHECK Refer to page
5
—
—
—
3, 4
—
5
—
—
• Are the headphones connected to the VS-10? Refer to the owner’s manual
for the VS-10 (sold separately).
—
No sound from the center
speaker.
• Is GAME or HALL selected for the 2-channel source on the VS-10 ?
Refer to the owner’s manual for the VS-10 (sold separately).
—
10
Rear Speakers (NX-VS10E)
Type .......................................................... Acoustic suspension type
Speaker ........................................ 8-cm cone, magnetically shielded
Maximum Input Power............................................................. 30 W
Impedance ............................................................................. 6 ohms
Dimensions (W x H x D).................................. 100 x 140 x 112 mm
Weight.................................................................................... 0.68 kg
General
Power Supply
[Europe and U.K. models] .................................AC 230V, 50 Hz
[U.S.A. and Canada models] .............................AC 120V, 60 Hz
[Australia model] ...............................................AC 240V, 50 Hz
Power Consumption
[Europe, U.K. and Australia models].................................. 90 W
[U.S.A. and Canada models] .............................................. 95 W
Accessories ..................................Speaker cords (15 m x 2, 4 m x 1)
System connector cable (3 m x 1)
Velcro strips (x 2)
Type A brackets (x 2)
Type B brackets (x 2)
Screws (x 2)
Wing nuts (x 2)
Specifications are subject to change without notice.
Amplifier Section
Minimum RMS Output Power
Subwoofer ............................ 50 W (100 Hz, 10% THD, 5 ohms)
Center speaker ....................... 40 W (1 kHz, 10% THD, 6 ohms)
Rear speakers ................... 25 W x 2 (1 kHz, 10% THD, 6 ohms)
Subwoofer (SW-VS10)
Type .......... Advanced YAMAHA Active Servo Technology System
Speaker ...................................... 16-cm cone, magnetically shielded
Maximum Input Power............................................................. 50 W
Impedance ............................................................................. 5 ohms
Dimensions (W x H x D) .................................. 200 x 395 x 400 mm
Weight.................................................................................... 10.6 kg
Center Speaker (NX-VS10C)
Type ........................................................................ Bass-Reflex type
Speakers................................. 8-cm cone x 2, magnetically shielded
Maximum Input Power............................................................. 40 W
Impedance ............................................................................. 6 ohms
Dimensions (W x H x D) .................................. 240 x 100 x 145 mm
Weight...................................................................................... 1.7 kg
SPECIFICATIONS
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in China V672820
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
Yamaha NX-SW10 Användarmanual
- Kategori
- Kompletterande musikutrustning
- Typ
- Användarmanual
- Denna manual är också lämplig för
på andra språk
- italiano: Yamaha NX-SW10 Manuale utente
- čeština: Yamaha NX-SW10 Uživatelský manuál
- español: Yamaha NX-SW10 Manual de usuario
- Deutsch: Yamaha NX-SW10 Benutzerhandbuch
- polski: Yamaha NX-SW10 Instrukcja obsługi
- português: Yamaha NX-SW10 Manual do usuário
- français: Yamaha NX-SW10 Manuel utilisateur
- Türkçe: Yamaha NX-SW10 Kullanım kılavuzu
- English: Yamaha NX-SW10 User manual
- dansk: Yamaha NX-SW10 Brugermanual
- русский: Yamaha NX-SW10 Руководство пользователя
- suomi: Yamaha NX-SW10 Ohjekirja
- Nederlands: Yamaha NX-SW10 Handleiding
- română: Yamaha NX-SW10 Manual de utilizare