KitchenAid KIF 5O41 PLETGS Användarguide

Instruction for use

2

3

Installation ............................................................................................................................................ 4

Product description .............................................................................................................................. 5

First time use ......................................................................................................................................... 6

Advice and tips ..................................................................................................................................... 8

Loading the racks ................................................................................................................................ 8

Selecting a cycle and options ..............................................................................................................10

Cycle table ........................................................................................................................................... 11

Options and settings .......................................................................................................................... 12

Settings menu .................................................................................................................................... 13

Care and maintenance ....................................................................................................................... 14

Troubleshooting .................................................................................................................................. 15

After-sales service ............................................................................................................................. 17

4

INSTALLATION

CONNECTING THE WATER SUPPLY

Adaptation of the water supply for installation should only be perfor-

med by a qualied technician.

The water inlet and outlet hoses may be positioned towards the right

or the left in order to achieve the best possible installation.

Make sure the dishwasher does not bend or squash the hoses.

CONNECTING THE WATER INLET HOSE

• Run the water until it is perfectly clear.

• Screw the inlet hose tightly into position and turn on the tap.

If the inlet hose is not long enough, contact a specialist store or an

authorised technician.

The water pressure must be within the values indicated in the Techni-

cal Data table - otherwise the dishwasher may be function properly.

Make sure the hose is not bent or compressed.

SPECIFICATIONS FOR THE CONNECTION OF THE WATER SUPPLY HOSE:

CONNECTING THE WATER OUTLET HOSE

Connect the outlet hose to a drain duct with a minimum diameter of

2 cm A.

The outlet hose connection must be at a height ranging from 40 to

80 cm from the oor or surface where the dishwasher rests.

Before connecting the water outlet hose to the sink drain, remove the

plastic plug B.

ANTI-FLOODING PROTECTION

Anti-ooding protection. To ensure oods do not occur, the dishwasher:

- is provided with a special system which blocks the water supply in

the event of anomalies or leaks from inside the appliance.

Some models are also equipped with the supplementary safety device

New Aqua Stop, which guarantees anti-ooding protection even in

the event of a supply hose rupture.

Under no circumstances should the water inlet hose be cut as it conta-

ins live electrical parts.

ELECTRICAL CONNECTION

WARNING: Under no circumstances should the water inlet hose

be cut as it contains live electrical parts.

Before inserting the plug into the electrical socket, make sure that:

• The socket is earth and complies with current regulations;

• The socket can withstand the maximum load of the appliance as

shown on the data plate located on the inside of the door (see

PRODUCT DESCRIPTION).

• The power supply voltage falls within the values indicated on the

data plate on the inside of the door.

• The socket is compatible with the plug of the appliance.

If this is not the case, ask an authorised technician to replace the plug

(see AFTER-SALES SERVICE). Do not use extension cables or multiple

sockets. Once the appliance has been installed, the power supply

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, have it replaced by the ma-

nufacturer or its authorised Technical Assistance Service in order to

prevent all potential hazards.

The Company shall not be held responsible for any incidents, if these

regulations are not observed.

POSITIONING AND LEVELLING

1. Position the dishwasher on a level sturdy oor. If the oor is uneven,

the front feet of the appliance may be adjusted until it reaches

a horizontal position. If the appliance is levelled correctly, it will be

more stable and much less likely to move or cause vibrations and

noise while it is operating.

2. Before recessing the dishwasher, stick the adhesive transparent strip

under the wooden shelf in order to protect it from any condensation

which may form.

3. Place the dishwasher so that its sides or back panel are in contact

with the adjacent cabinets or the wall. This appliance can also be

recessed under a single worktop.

4. To adjust the height of the rear foot, turn the red hexagonal bushing

on the lower central part at the front of the dishwasher using a

hexagonal spanner with an opening of 8 mm. Turn the spanner in

a clockwise direction to increase the height and in an anticlockwise

direction to decrease it.

DIMENSIONS AND CAPACITY:

WATER SUPPLY cold or hot (max. 60°C)

WATER INTAKE 3/4”

POWER OF WATER PRESSURE

0,05 ÷ 1 MPa (0.5 ÷ 10 bar)

7,25 – 145 psi

WIDTH 598 mm

HEIGHT 820 mm

DEPTH 555 mm

CAPACITY 14 standard place-settings

ATTENTION: If the appliance must be moved at any time, keep it in an upright position; if absolutely necessary, it may be tilted onto its back.

Before using the appliance carefully read Safety Instructions guide.

MIN 40 cm

MAX 80 cm

5

1 2 3 4 5 6 7 8 9 10

1. Upper rack

2. Cutlery rack

3. Foldable aps

4. Upper rack height adjuster

5. Upper sprayer arm

6. Dynamic Clean support

7. Lower rack

8. Lower sprayer arm

9. Filter Assembly

10. Salt reservoir

11. Detergent and Rinse Aid dispensers

12. Rating plate

13. Control panel

1. ON-OFF button

2. CYCLES 6 buttons for direct access popular cycles

3. EXTRA CYCLES button. Access to other cycles

4. INFO button. Provide info for selected cycle

5. DISPLAY - Indicators area

6. DISPLAY - Information area

7. PREVIOUS button for options/settings

8. SET button. Select/change options and settings

9. NEXT button for options/settings

10. START button

PRODUCT DESCRIPTION

CONTROL PANEL

DISPLAY - INDICATORS

A. START DELAY

B. ECO CYCLE

C. MULTIZONE - Cutlery rack

D. CLOSED WATER TAP

E. ADD SALT

F. MULTIZONE - Upper Rack

G. MULTIZONE - Lower Rack

H. ADD RINSE AID

I. TABLET

A B C

I H G F

D

E

The control panel of this dishwasher activates pushing by ON/OFF button.

For energy saving the control panel deactivates automatically after 10 minutes if no cycle has started.

1

7

2

3

4

6

5

11

13

12

10

8

9

0000 000 00000

Service:

6

After connecting the appliance to the power supply for the rst time,

the display will guide you to set up the appliance for rst use.

1. The language selection

To select preferred language please

press button „<” or „>”.

Conrm by pressing „SET” button.

After language conrmation, the appliance will go through the rst

time use conguration menu.

2. Setting the water hardness

The water hardness is by default

set to level 3. To change water

hardness level press button „<” or „>”

repeatedly.

To conrm your choice press „SET”

button. The level must be set

according to the table below.

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in your

house. This information can be obtained from your local water supplier.

3. Filling the water softener

When water hardness is set, it is

required to ll water softener with

water and special regeneration salt.

Remove the lower rack and unscrew

the reservoir cap (anticlockwise)

As a rst step it is needed to ll

reservoir with water ( ~1.5 litres).

Once done, proceed to the next

step by pressing „SET” button.

Position the funnel (see gure) and ll the salt reservoir right up to its

edge (approximately 1 kg); it is not unusual for some water will spill out.

Remove the funnel and wipe any salt residue away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get

into the container during the wash program (this could damage the

water softener beyond repair).

Once done, proceed to the next step by pressing „SET” button.

Only use salt that has been specically designed for dishwashers.

4. Setting the brightness level

The brightness level is by default set

to level 5. To change brightness level

press button „<” or „>” repeatedly.

To conrm Your choice press „SET”

button.

5. Detergent type operation

In this step it is very important to

choose what type of detergent will

be used (tablet/capsule or

gel/powder).

If you prefer to use All-in-one

detergent in tablet or capsule for

washing - press „SET”, then go to

step 7. Open tap operation on the

next page.

The symbol on display will be lit. If you prefer to use gel or po-

wder detergent for washing, press „<” or „>”, then go to step 6. Rinse

aid operation.

6. Rinse aid operation*

*If All-in-one detergent was chosen in the previous step, this step will

be skipped by the appliance.

WATER HARDNESS = 3

<> = CHANGE OK = YES

WATER HARDNESS

1=MIN, 5=MAX

LANGUAGE: ENGLISH?

<> = CHANGE OK = YES

ENGLISH

SELECTED

POUR WATER

OPERATION

INSERT 1,5 LITER OF

OK = DONE

WATER IN THE

OK = DONE

WATER SOFTENER

OK = DONE

INSERT SALT

OPERATION

ADD 1KG OF SALT

OK = DONE

IN THE SALT DISPENSER

OK = DONE

RINSE AID

OPERATION

INSERT RINSE AID

OK = DONE

IN THE DISPENSER

OK = DONE

FIRST TIME USE

ADJUST BRIGHTNESS

1=MIN, 5=MAX

BRIGHTNESS = 5

<> = CHANGE OK = YES

DETERGENT TYPE

OPERATION

DO YOU USE

<> = NO OK = YES

DETERGENT?

<> = NO OK = YES

“ALL IN ONE”

<> = NO OK = YES

A

B

Water Hardness Table

Level

°dH

German degrees

°fH

French degrees

°Clark

English degrees

1 Soft 0 - 6 0 - 10 0 - 7

2 Medium 7 - 11 11 - 20 8 - 14

3 Average 12 - 16 21 - 29 15 - 20

4 Hard 17 - 34 30 - 60 21 - 42

5 Very hard 35 - 50 61 - 90 43 - 62

Whenever you need to add salt, it is mandatory to complete the pro-

cedure before the beginning of the washing cycle to avoid corrosion.

Residual saline solution or grains of salt can lead to corrosion,

irreparably damaging the stainless steel components.

The guarantee is not applicable if faults are caused by such

circumstances.

If the salt container is not lled, the water softener and the heating

element may be damaged as a result of limescale accumulation.

Using of Salt is recommended with any type of dishwasher detergent.

7

1. Open the dispenser B by pressing and pulling up the tab on the lid.

2. Carefully introduce the rinse aid as far as the maximum (110 ml) re-

ference notch of the lling space A - avoid spilling it. If this happens,

clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

4. Conrm operation by pressing „SET” button.

NEVER pour the rinse aid directly into the tub.

Setting rinse aid level

(not necessary when using tablets/capsules)

The rinse aid dosage can be adjusted to the detergent used. The lower

the setting, the less rinse aid is dispensed. The factory setting is for (5)

level.

To change, follow instructions in section “SETTINGS / MENU”.

7. Open tap operation

Check water tap is open. If closed, open it then conrm by pressing

„SET” button.

8. First cycle operation

Before normal use of appliance it is

recommended to run Intensive cyc-

le rst, to calibrate the appliance.

Insert a detergent into dispenser

chamber D (see below), then press

„SET” button.

Intensive cycle will be selected

automaticly. Press „START”

button and close the appliance

door within 4 seconds.

This rst cycle can be up to 20

minutes longer as a result of the

automatic calibration process.

After this process the appliance is ready for normal use.

OPEN TAP

OPERATION

OPEN THE

OK = DONE

WATER TAP

OK = DONE

FIRST CYCLE

OPERATION

REMEMBER TO RUN THE

OK = EXIT

INTENSIVE CYCLE

OK = EXIT

WITH EMPTY BASKETS

OK = EXIT

TO COMPLETE

OK = EXIT

THE FIRST SET UP

OK = EXIT

ADDING A DETERGENT

To achieve the best washing and drying results, the combined use of

detergent, rinse aid liquid and rened salt is required.

We recommend using detergents that do not contain phosphates or

chlorine, as these products are harmful to the environment.

Good washing results also depend on the correct amount of deter-

gent being used.

Exceeding the stated amount does not result in a more eective wash

and increases environmental pollution.

The amount can be adjusted to the soil level. In the case of normally

soiled items, use approximately either 35g (powder detergent) or

35ml (liquid detergent) and additional tea spoon of detergent directly

inside the tub. If tablets are used, one tablet will be enough.

If the crockery is only lightly soiled or if it has been rinsed with water

before being placed in the dishwasher, reduce the amount of deter-

gent used accordingly (minimum 25 g/ml) e.g. skip the powder/gel

putted inside the tub.

To open the detergent dispenser,

press button C. Introduce the deter-

gent into the dry dispenser D only.

Place the amount of detergent for

pre-washing directly inside the tub.

1. When measuring out the deter-

gent refer to the mentioned ear-

lier information to add the proper

quantity. Inside the dispenser D

there are indications to help the

detergent dosing.

2. Remove detergent residues from the edges of the dispenser and

close the cover until it clicks.

3. Close the lid of the detergent dispenser by pulling it up until the

closing device is secured in place.

The detergent dispenser automatically opens up at the right time

according to the program.

If you are using a All-in-one detergents, we recommend that you add

salt in any case, especially if the water is hard or very hard (follow the

instructions given on the packaging).

C

D

Usage of detergent not designed for dishwashers may cause

malfunction or damage to the appliance.

8

ADVICE AND TIPS

LOADING THE RACKS

CUTLERY RACK

The third rack was designed tohouse the cutlery.

Arrange the cutlery as shown in the gure.

A separate arrangement of the cutlery makes collection easier after

washing and improves washing and drying performance.

Knives and other utensils with sharp edges must be positioned

with the blades facing downwards.

The geometry of the rack makes it possible to place such small items as

coee cups in the area in the middle.

The cutlery basket is equipped with two sliding side trays to make the

most of the height of the space below and enable the loading of high

items into upper rack.

TIPS

Before loading the baskets, remove all food residues from the crockery

and empty the glasses. You do not need to rinse beforehand under

running water.

Arrange the crockery so that it is held in place rmly and does not tip

over; and arrange the containers with the openings facing downwards

and the concave/convex parts placed obliquely, thus allowing the

water to reach every surface and ow freely.

Warning: lids, handles, trays and frying pans do not prevent the spray-

er arms from rotating.

Place any small items in the cutlery basket.

Very soiled dishes and pans should be placed in the lower basket

because in this sector the water sprays are stronger and allow a higher

washing performance.

After loading the appliance, make sure that the sprayer arms can

cotate freely.

UNSUITABLE CROCKERY

• Wooden crockery and cutlery.

• Delicate decorated glasses, artistic handicraft and antique crockery.

Their decorations are not resistant.

• Parts in synthetic material which do not withstand high temperatures.

• Copper and tin crockery.

• Crockery soiled with ash, wax, lubricating grease or ink.

The colours of glass decorations and aluminium/silver pieces can

change and fade during the washing process. Some types of glass (e.g.

crystal objects) can become opaque after a number of wash cycles too.

DAMAGE TO GLASS AND CROCKERY

• Only use glasses and porcelain guaranteed by the manufacturer as

dishwasher safe.

• Use a delicate detergent suitable for crockery

• Collect glasses and cutlery from the dishwasher as soon as the wash

cycle is over.

TIPS ON ENERGY SAVING

• When the household dishwasher is used according to the manufac-

turer’s instructions, washing tableware in a dishwasher usually

consumes less energy and water than hand dishwashing.

• In order to maximize dishwasher eciency it is recommended to

initiate the wash cycle once dishwasher is fully loaded. Loading

the household dishwasher up to the capacity indicated by the man-

ufacturer will contribute to energy and water savings. Information

on correct loading of tableware can be found in Loading chapter.

In case of partial loading it is recommended to use dedicated wash

options if available (Half load/ Zone Wash, Multizone), illing up only

selected racks. Incorrect loading or overloading the dishwasher may

increase resources usage (such as water, energy and time, as well as

increase noise level), reducing cleaning and drying performance.

• Manual pre-rinsing of tableware items leads to increased water and

energy consumption and is not recommended.

HYGIENE

To avoid odour and sediment which can be accumulated in the

dishwasher please run a high temperature program at least once a

month. Use a tea spoon of detergent and run it without the loading to

clean your appliance.

9

UPPER RACK

Load delicate and light

dishes:glasses, cups, saucers, low

salad bowls.

The upper rack has tip-up

supports which can be used in a

vertical position when arranging

tea/ dessert saucers or in a lower

position to load bowls and food

containers.

(loading example for the upper rack)

FOLDABLE FLAPS WITH ADJUSTABLE POSITION

The side foldable aps can be

positioned at three dierent heights to

optimize the arrangement of crockery

inside the rack.

Wine glasses can be placed safely in

the foldable aps by inserting the stem

of each glass into the corresponding

slots.

Depending on the model:

• to unfold the aps there is needed

to slide it up and rotate or release it

from the snaps and pull it down.

• to fold the aps there is needed to rotate it and slide aps down or

pull it up and attach aps to the snaps.

ADJUSTING THE HEIGHT OF THE UPPER RACK

The height of the upper rack can be adjusted:

high position to place bulky crockery in the

lower basket and low position to make the

most of the tip-up supports by creating more

space upwards and avoid collision with the

items loaded into lower rack.

The upper rack is equipped with a Upper

Rack height adjuster (see gure), without

pressing the levers, lift it up by simply holding

the rack sides, as soon as the rack is stable in

its upper position.

To restore to the lower position, press the levers A at the sides of the

rack and move the basket downwards.

We strongly recommend that you do not adjust the height of the

rack when it is loaded.

NEVER raise or lower the basket on one side only.

LOWER RACK

For pots, lids, plates, salad bowls, cutlery etc. Large plates and lids

should ideally be placed at the sides to avoid interferences with the

spray arm.

The lower rack has tip-up supports which can be used in a vertical

position when arranging plates or in a horizontal position (lower) to

load pans and salad bowls easily.

(loading example for the lower rack)

GLASS CARE

Dedicated accessory that

allows you to safely store

dierent types of stem

glasses in the lower rack.

It enables cleaning &

drying results by allowing

an optimised and stable

positioning of the glasses.

DYNAMIC CLEAN IN LOWER RACK

Dynamic Clean uses the special water

jets in the rear of cavity to wash more

intensively the high dirty items.

Placing the pots/casseroles faced to

the Dynamic Clean® component please

activate the DYNAMIC CLEAN on the

panel.

The lower rack has a Dynamic Clean, a special pull-out support in the

rear of the rack that can be used to support frying pans or baking pans

in upright position, thus taking up less space.

How to use Dynamic Clean:

1. Adjust the Dynamic Clean area

(G) folding down the rear plate

holders to load pots.

2. Load pots and casseroles inclined

vertically in Dynamic Clean area.

Pots have to be inclined towards

the power water jets.

2

3

1

3

2

A

B

10

SELECTING A CYCLE AND OPTIONS

POWER

CLEAN

50° 3:10h

DYNAMIC

CLEAN

50° 3:10h

MODIFYING A RUNNING PROGRAM

If a wrong program was selected, it is possible to change it, provided

that it has only just begun: open the door, press and hold the „ON/OFF”

button, the machine will switch o.

Switch the machine back on using the „ON/OFF” button and

select the new wash cycle and any desired options; start the cycle

by pressing the „START” button and closing the door within 4

sec.

TO PAUSE THE CYCLE (ADDING EXTRA ITEMS)

Open the door and place the crockery inside the dishwasher,

(beware of HOT steam!). Press „START” button and close the

door within 4 sec. to resume the cycle from the point at which it was

interrupted.

ACCIDENTAL INTERRUPTIONS

If the door is opened during the wash cycle, or if there is a power

cut, the cycle stops. To resume the cycle from where it was interrup-

ted, press the „START” button and close the door within 4 sec.

Open appliance door (beware of hot steam!) and unload the racks,

starting from the lower rack rst.

If it is needed to rell salt reservoir or rinse aid dispenser, it is

recommended to do this operations right before start of the next

cycle.

ECO CYCLE

1 2 3

45

NORMALLY SOILED CROCKERY.

STANDARD PROGRAM,

WATER ENERGY

The list of available cycles and options can be found in Cycle Table

on next page. Eco cycle is selected by default. If you want to have Last

Used cycle selected by default, you can change it in „Settings Menu”.

It is possible to select a cycle by pressing 1 of 6 cycles direct access

buttons or by pressing „Extra Cycles” button repeatedly. When the

last one is reached a further press goes back to the rst.

Press cycle button to choose cycle in accordance with the level

of soiling of the dishes and with Cycle Table. Information will be

shown on the display:

1. Indicators

2. Name of the selected cycle

3. Vertical bar showing the position of the extra cycle list only

4. Energy consumption of the selected cycle

5. Water consumption of the selected cycle

Three seconds after selecting a cycle, its

time and temperature will be displayed

(if available).

Press „INFO” button to display a brief description of the cycle and

its water / energy consumption.

During the selection phase the „START” LED blinks.

Additional options are available for most cycles (see „Options and

Settings” section). When any option is selected, its name is shown on

the display on the right.

If more than one option is selected one

bullet point for each option is displayed.

Each option name is displayed for 3 sec.

with its bullet point fulled.

When the cycle and option selection is complete, press „START”

button and close the door within 4 seconds to start chosen cycle.

After the cycle nishes, there is an acustic signal and the dispaly shows:

On the display additional information can be shown:

• ADD SALT - rell salt reservoir.

• ADD RINSE AID - rell rinse aid.

• DEGREASE AND CLEAN MACHINE WE RECOMMEND WPRO - every 50 cycle, will be

recommended to use the WPRO cleaner (according to instruction

on the consumable).

After 10 minutes the appliance switches o.

WATER SOFTENING SYSTEM

Water softener automatically reduces water hardness, consequently

preventing scale buildup on heater, contributing also to better cleaning

eciency.

This system regenerates itself with salt, therefore it is required to

rell salt container when empty.

Frequency of regeneration depends on water hardness level setting -

regeneration takes place once per 6 Eco cycles with water hardness

level set to 3.

Regeneration process starts in nal rinse and nishes in drying phase,

before cycle ends.

• Single regeneration consumes: ~3.5L of water;

• Takes up to 5 additional minutes for the cycle;

• Consumes below 0.005kWh of energy.

CYCLE FINISHED

11

CYCLES TABLE

CYCLE Available options *

Drying

phase

Auto Door

Opening /

NaturalDry

Duration of

wash cycle

(h:min)

**

Water

consumption

(l/cycle)

Energy

cosumption

(kWh/cycle)

ECO

50°

TABLET, START DELAY,

DYNAMIC CLEAN, BOOST

3:10 9.5 0.75

DYNAMIC SENSOR

50-60°

TABLET, START DELAY, MULTIZONE,

DYNAMIC CLEAN, BOOST

1:25 - 3:00 7.0 - 14.0 0.90 - 1.40

PROFESSIONAL

65°

TABLET, START DELAY, MULTIZONE,

DYNAMIC CLEAN

- 2:27 16.5 1.70

MIXED

60°

TABLET, START DELAY, MULTIZONE

2:30 16.0 1.30

FAST WASH&DRY

50°

TABLET, START DELAY, MULTIZONE

1:25 11.5 1.10

GLASS

45°

TABLET, START DELAY, MULTIZONE,

BOOST

2:05 11.5 1.20

EXTRA CYCLES - available by pressing button

FAST 30’ 50°

TABLET, START DELAY, MULTIZONE

- - 0:30 9.0 0.50

SILENT 50°

TABLET, START DELAY

3:30 15.0 1.15

DYNAMIC HYGIENE 65°

START DELAY

- 1:40 10.0 1.30

PRE-WASH cold

START DELAY, MULTIZONE

- - 0:12 4.5 0.01

SELF CLEAN 65°

START DELAY

- - 0:50 8.0 0.85

1. ECO - Eco programme is suitable to clean normally soiled tableware, that for this use, it is the most ecient programme in terms of its

combined energy and water consumption, and that it is used to assess compliance with the EU Ecodesign legislation.

2. DYNAMIC SENSOR - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program

accordingly.

3. PROFESSIONAL - Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used for delicate items).

4. MIXED  Mixed soil. For normally soiled dishes with dried food residues.

5. FAST WASH&DRY - Normally soiled crockery. Everyday cycle, that ensures optimal cleaning performance in shorter time.

6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.

EXTRA CYCLES

7. FAST 30’ - Program to be used for half load of lightly-soiled dishes with no dried food residues. Does not include drying phase.

8. SILENT -

Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.

9. DYNAMIC HYGIENE -

Normally or heavily soiled crockery, with additional antibacterial wash. Can be used to perform maintenance of the

dishwasher.

10. PRE-WASH - Crockery to be washed later. No detergent to be used with this program.

11. SELF CLEAN - Program to be used to perform maintenance of the dishwasher, to be carried out only when the dishwasher is EMPTY using

specic detergents designed for dishwasher maintenance.

Notes:

Please note that cycle Fast 30’ is dedicated for lightly soiled dishes.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.

Pre-treatment of the dishes is not needed before any of the programs.

* Not all options can be used simultaneously.

** Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature

and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options

and sensor calibration. The sensor calibration can increase program duration up to 20 min.

12

OPTIONS AND SETTINGS

TABLET (All-in-one)

This setting allows you to optimise the performance of the cycle

according to the type of detergent used. Enable it if you use combined

detergents in tablet form (rinse aid, salt and detergent in 1 dose).

To set the Tablet, enter in the setting

menu by pressing „SET” button and

navigate with „< , >” until „TABLET”

is shown, then press „SET” button.

START DELAY

The start of the cycle may be delayed for a selected period of time.

To set a delay, enter in the setting menu by pressing „SET” button and

navigate with „< , >” until „START DELAY” is shown, then press „SET” button.

With each press of the button “>” or “<“, the delay start increases by:

• every 0:30 if selection below 4 hours,

• every 1:00 if selection is below 12 hours,

• every 2 hours if selection is above 12 hours.

Default value is OFF.

If delay is selected, the is lit.

Once „SET” button is pressed the

delay is conrmed and the machine

comes back to the cycle selection

screen with delay value visible.

Press „START” and close the door within 4 sec. to start the delay.

To remove the delay, press „<” or „>” button until „OFF” is displayed.

MULTIZONE

If there are not many dishes to be washed it can be loaded in one rack

only. Using this option you can select which rack you want to wash.

To set the Multizone, enter in the setting menu by pressing „SET”

button and navigate with „< , >” until „MULTIZONE” is shown, then

press „SET” button.

By default the MULTIZONE is not

active and all racks icons are lit.

The multizone icon becomes lit.

Remember to load the upper or lower rack only, and to reduce the

amount of detergent accordingly.

If upper rack is removed, please apply detergent directly to tub

instead of detergent dispenser.

DYNAMIC CLEAN

Thanks to additional water jets this option provides a more intensive

and powerful wash in the specic area of lower rack.

Default value is OFF.

To set the Dynamic Clean, enter in

the setting menu by pressing „SET

button and navigate with „< , >”

until „DYNAMIC CLEAN” is shown,

then press „SET” button.

BOOST

The boost option delivers a cut 25%-67% of the duration for main

cycles, while ensuring an optimal level of washing and drying.

In order to do that it will require more water and energy consumption

compared to the regular full-lenght cycle. The option can be selected

on programs: Eco 50°, Dynamic Sensor 50-60°, Glass 45°.

To set the Boost, enter in the setting

menu by pressing „SET” button and

navigate with „< , >” until „BOOST”

is shown, then press „SET” button.

With each press of the button „>” or

„<“ option will be ON or OFF.

Conrm by pressing „SET” button.

FLOOR LIGHT

A LED light projected on the oor indicates that the dishwasher is

working. The light stays on during the cycle and switches o at the

end of the cycle.

This feature is active by default, but it is possible to deactivate it in the

“SETTINGS MENU”.

TUB LIGHT

When the feature is active the LEDs in the tub are automatically

switched on/o as soon as the user open/close the door respectively.

If the door remains opened for more than 10 min, the LEDs in the

tub switch o (to turn them on again, the door has to be closed and

opened again).

This feature is active by default, but it is possible to deactivate it in the

“SETTINGS MENU”.

TABLET OFF

TABLET ON

MULTIZONE OK

With each cycle additional options can be used. A full list of available options working with specic cycles can be found in the Cycle Table on

the previous page. All active options are shown on the display.

To set an option press „SET” button. SET OPTIONS message is shown for a few seconds. Then use „<” or „>” button to navigate through the option

list. Press „SET” to select the option, in the setting menu the LED above „SET” button is lit.

If the option is not available, it will be still visible in its position but with „ ”

START DELAY OFF

<STARTS IN h> OFF

<STARTS IN h> 4:00

BOOST OFF

BOOST ON

DYNAMIC CLEAN OFF

DYNAMIC CLEAN ON

13

SETTINGS MENU

Language

To change language, enter in the

setting menu by pressing „SET”

button and navigate with „< , >”

until „LANGUAGE” is shown, then

press „SET” button.

First cycle

You can choose which cycle is

selected by default when switching

on the appliance: ECO or the LAST

USED one.

To change rst cycle, enter in the

setting menu by pressing „SET” but-

ton and navigate with „< , >” until

„FIRST CYCLE” is shown, then press

„SET” button.

Sounds

To change sounds, enter in the

setting menu by pressing „SET”

button and navigate with „< , >”

until „SOUNDS” is shown, then press

„SET” button.

Choose between 2 levels: HIGH;

LOW. Can be also OFF.

Water Hardness

To change water hardness level,

enter in the setting menu by

pressing „SET” button and navigate

with „< , >” until „WATER HARDNESS”

is shown, then press „SET” button.

To setup correct level according to water hardness, see table on page 6.

Screen Brightness

To change screen brightness

level, enter in the setting menu by

pressing „SET” button and navigate

with „< , >” until „SCREEN BRIGHT.” is

shown, then press „SET” button.

Choose between ve levels: 1, 2, 3, 4 and 5.

Floor Light

To change oor light, enter in the

setting menu by pressing „SET”

button and navigate with „< , >”

until „FLOOR LIGHT” is shown, then

press „SET” button.

Tub Light

To change tub light, enter in the

setting menu by pressing „SET”

button and navigate with „< , >”

until „TUB LIGHT” is shown, then

press „SET” button.

Auto Door Opening / NaturalDry

To set Auto Door Opening / NaturalDry

on or o, enter in the setting menu by

pressing „SET” button and navigate with

„< , >” until „NATURALDRY” is shown,

then press „SET” button.

Auto Door Opening / NaturalDry is a convection drying system which

automatically opens the door during/after drying phase to ensure ex-

ceptional drying performance every day. Door opens at the tempera-

ture that is safe to your kitchen furniture, thus door will not be opened

when the option of BOOST is on.

As additional steam protection, special designed protection foil is added

together with the dishwasher. To see how to mount protection foil

please refer to (INSTALLATION GUIDE).

Rinse Aid level

To change rinse aid level, enter in

the setting menu by pressing „SET”

button and navigate with „< , >”

until „RINSE AID LEV.” is shown, then

press „SET” button.

Choose between ve levels: 1, 2, 3, 4 and 5.

If the rinse aid level is set to 1, no rinse aid will be supplied. The LOW

RINSE AID indicator light will not be lit if you run out of rinse aid.

The factory setting is for (5) level .

• If you see bluish streaks on the dishes, set a low number (2-3).

• If there are drops of water or limescale marks on the dishes, set

a high number (4-5).

Demo mode

To see to demo mode, enter in the

setting menu by pressing „SET”

button and navigate with „< , >”

until „DEMO MODE” is shown, then

press „SET” button.

Reset to factory default

To reset to factory default, enter in

the setting menu by pressing „SET”

button and navigate with „< , >”

until „RESET TO DEF.” is shown, then

press „SET” button.

Exit

To exit the setting menu, press any

cycle button or press „< , >” button

untill EXIT is shown, then press

„SET” button.

8.NATURALDRY ON

8.NATURALDRY OFF

9.RINSE AID LEV. 4

9.RINSE AID LEV. 5

11.RESET TO DEF. OK

11.OFF

11.ON < >

12.EXIT < >

4.WATER HARDNESS 3

5.SCREEN BRIGHT. 5

6.FLOOR LIGHT ON

7.TUB LIGHT ON

To change machne settings you need to enter into the Settins Menu.

Press „SET” button and navigate with „< , >” until SETTINGS is shown, then press „SET” button.

To exit the setting menu, press any cycle button or press „< , >” button untill EXIT is shown, then press „SET” button.

4.WATER HARDNESS 4

5.SCREEN BRIGHT. 3

6.FLOOR LIGHT OFF

7.TUB LIGHT OFF

1.LANGUAGE OK

1.ENGLISH

1.ITALIAN < >

2.FIRST CYCLE OK

2.<LAST USED>

2.<ECO> < >

3.SOUNDS OK

3.<OFF>

3.<HIGHT> < >

10.DEMO MODE ON

10.DEMO MODE OFF

14

CARE AND MAINTENANCE

CLEANING THE DISHWASHER

Any marks on the inside of the appliance may be

removed using a cloth dampened with water and a

little vinegar.

The external surfaces of the machine and the control

panel can be cleaned using a non-abrasive cloth

which has been dampened with water. Do not use

solvents or abrasive products.

PREVENTING UNPLEASANT ODOURS

Always keep the door of the appliance ajar in order to avoid moisture

from forming and being trapped inside the machine.

Clean the seals around the door and detergent dispensers regularly

using a damp sponge. This will avoid food becoming trapped in the se-

als, which is the main cause behind the formation of unpleasant odours.

CHEKING THE WATER SUPPLY HOSE

Check the inlet hose regularly for brittleness and cracks. If damaged,

replace it by a new hose available through our After-Sales Service or

your specialist dealer. Depending on the hose type:

If the inlet hose has a transparent coating, periodically check if the

colour intensies locally. If yes, the hose may have a leak and should

be replaced.

For water stop hoses: check the small safety valve inspection window

(see arrow). If it is red, the water stop function was triggered, and the

hose must be replaced by a new one.

For unscrewing this hose, press the release button while unscrewing

the hose.

CLEANING THE WATER INLET HOSE

If the water hoses are new or have not been used for an extended

period of time, let the water run to make sure it is clear and free of im-

purities before performing the necessary connections. If this precau-

tion is not taken, the water inlet could become blocked and damage

the dishwasher.

CLEANING THE FILTER ASSEMBLY

Regularly clean the lter assembly so that the lters do not clog and

that the waste water ows away correctly.

Using dishwasher with clogged lters or foreign objects inside ltra-

tion system or sprayarms may cause unit malfunction resulting in lose

of performance, noisy work or higher resources usage.

The lter assembly consists of three lters which remove food residues

from the washing water and then recirculate the water.

The dishwasher must not be used without lters or if the lter is

loose.

At least once per month or after each 30 cycles, check the lter assembly

and if necessary clean it thoroughly under running water, using a non-

-metallic brush and following the instructions below:

1. Turn the cylindrical lter A in an anti-clockwise direction and pull it

out (Fig 1).

2. Remove the cup lter B by exerting a slight pressure on the side

aps (Fig 2).

3. Slide out the stainless-steel plate lter C (Fig 3).

4. In case you nd foreign objects (such as broken glass, porcelain,

bones, fruit seeds etc.) please remove them carefully.

5. Inspect the trap and remove any food residues. NEVER REMOVE

the wash-cycle pump protection (black detail) (Fig 4).

After cleaning the lters, re-place the lter assembly and x it in po-

sition correctly; this is essential for maintaining the ecient operation

of the dishwasher.

CLEANING THE SPRAY ARMS

On occasions, food residue may

become encrusted onto the spray

arms and block the holes used

to spray the water. It is therefore

recommended that you check the

arms from time to time and clean

them with a small non-metallic

brush.

To remove the upper spray arm,

turn the plastic locking ring in an

anti-clockwise direction. The upper spray arm should be replaced so

that the side with the greater number of holes is facing upwards.

The lower spray arm may be removed

by pulling it upwards.

21

43

A

C

A

B

ATTENTION: Always unplug the appliance when cleaning it and when performing maintenance work.Do not use ammable liquids to clean

the machine.

15

TROUBLESHOOTING

PROBLEMS POSSIBLE CAUSES SOLUTIONS

Display shows:

CHECK SALT! or

ADD SALT

Salt reservoir is empty.

Rell reservoir with salt (see page 6).

Adjust water hardness (see page 6).

Display shows:

CHECK RINSE AID! or ADD RINSE

AID

Rinse aid dispenser is empty. Rell dispenser with rinse aid (see page 6).

... is not working / will not

start.

The appliance must be switched on. Check the household circuit fuse if there is no power supply.

The appliance door doesn’t close. Check if the appliance door is closed.

“Start Delay” option is ON.

Check whether the „Start Delay” option has been selected. If it has, the

appliance will start once the set time has elapsed. If necessary, Reset the

current cycle by switching OFF the dishwasher , then switch it on again,

select a new cycle, press START and close the door within 4 seconds.

Display shows: F6

symbol on the display

indicators

Water pressure is too low.

The water tap must be fully open during water inlet (minimum capaci-

ty: 0.5 litres per minute).

Kinked water inlet hose or cloged

inlet lters.

The water inlet hose must not be kinked and the inlet lter in the water

tap connector must not be dirty or clogged.

Display shows: F3

Dirty lters. Clean the lters.

Kinked drain hose. The drain hose must not be kinked.

Syphon hose connection closed.

The closure disk of the syphon hose connection

must be removed.

Display shows: F2

Dirty lters or spray arms. Clean lters and spray arms.

Too little water in the appliance

system.

Concave items (e.g. bowls, cups) must be arranged

facing downwards in the rack.

Drain hose incorrectly tted.

The drain hose must be tted correctly (for high mounted appliances,

leave min. 200 - 400mm from the lower edge of the appliance) - see

Installation.

High level of foam inside.

Repeat without detergent or wait until foam

disappears..

Water pressure is too low.

The water tap must be fully open during water inlet (minimum capaci-

ty: 0.5 litres per minute).

Kinked water inlet hose or cloged

inlet lters.

The water inlet hose must not be kinked and the inlet lter in the water

tap connector must not be dirty or clogged.

Display shows:

PRESS START AND

CLOSE THE DOOR

Door is not closed within

4 seconds of button press.

Press again and close the appliance door within 4 seconds.

Display shows:

OPEN AND CLOSE

THE DOOR

The door was not open between

cycles.

Unload appliance (if not unloaded before), open and close the door.

Display shows: Fx

Appliance has technical defect.

Call customer service (state fault displayed).

Close the water tap.

In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.

For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.

The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.

16

PROBLEMS POSSIBLE CAUSES SOLUTIONS

The door doesn’t

lock.

Racks are not t to the end. Verify that racks are t to the end.

The door is not lock. Vigorously push the door until you hear the “clack” sound.

The dishwasher

makes excessive

noise.

The dishes are rattling against each. Arrange the crockery correctly (see Loading the Racks).

An excessive amount of foam has been

produced.

The detergent has not been measured out correctly or it is not suitable for

use in dishwashers (see Filling the Detergent Dispenser). Reset the current

cycle by switching OFF the dishwasher, then switch it on again, select a

new program, press START and close the door within 4 seconds. Please do

not add any detergent.

The dishes have not

been dried.

The selected program hasn’t any drying

phase.

Verify on the programs table if the selected program has the drying phase.

The rinse aid has run out or the resolution

is not adequate.

Add the rinse aid or adjust the dosage levels higher (see Filling the Rinse

Aid Dispenser).

The dishes are made of non-stick or

plastic.

It is normal the presence of drops of water (see Tips).

The dishes are not

clean.

The crockery has not been arranged

properly.

Arrange the crockery correctly (see Loading the Racks).

The spray arms cannot rotate freely, being

hindered by the dishes.

Arrange the crockery correctly (see Loading the Racks).

The wash cycle is too gentle and/or deter-

gent eciency is low.

Select an appropriate wash cycle (see Programs Table).

An excessive amount of foam has been

produced (see AFTER-SALES SERVICE).

The detergent has not been measured out correctly or it is not suitable for

use in dishwashers (see Filling the Detergent Dispenser). Reset the current

cycle by switching OFF the dishwasher, then switch it on again, select a

new program, press START and close the door within 4 seconds. Please do

not add any detergent.

The cap on the rinse aid compartment has

not been shut correctly.

Make sure the cap of the rinse aid dispenser is closed.

The lter is soiled or clogged. Clean the lter assembly (see Care and Maintenance).

There is no salt. Fill the salt reservoir (see Filling the Salt Reservoir).

The dishes and glas-

ses show calcination

or a whitish lm.

The salt level is too low. Fill the salt reservoir (see Filling the Salt Reservoir).

The adjustment of the water hardness is

not adequate.

Increase the values (see Water Hardness Table).

The cap of the salt reservoir is not proper-

ly closed.

Check to have properly closed the salt reservoir cap.

The rinse aid is used up or the dosage is

insucient.

Add the rinse aid or adjust the dosage levels higher.

The dishes and

glasses are blue

streaked or have a

bluish tinge.

The rinse aid dosage is excessive. Adjust the dosage rates below.

17

AFTER-SALES SERVICE

Policy and standard documentation and additional product information can be found by:

• Visiting our website: docs.kitchenaid.eu

• Using QR Code

• Alternatively, contact our After-sales Service (See phone number in the warranty booklet).

When contacting our After-sales Service, please state the codes provided on your product’s

identication plate.

The model information can be retrieved using the QR-Code reported in the energy label.

The label also includes the model identier that can be used to consult the portal of the registry at

https://eprel.ec.europa.eu (available only on certain models).

IEC 436

:

18

19

EN

Printed in Italy

11/20

400011509467B

Sidan laddas ...

KitchenAid KIF 5O41 PLETGS Användarguide

KitchenAid KIF 5O41 PLETGS Användarguide

på andra språk

Relaterade papper

Andra dokument