Yamaha RMio64 Bruksanvisning

Typ
Bruksanvisning
EnglishDeutschFrançaisEspañolPortuguêsItalianoРусский
Owners Manual
Bedienungsanleitung
Mode d’emploi
Manual de instrucciones
Manual do Proprietário
Manuale di istruzioni
Руководство пользователя
JA
RU
IT
PT
ES
FR
DE
EN
I/O RACK
AUDIO INTERFACE
RMio64-D Owner’s Manual
2
Explanation of Graphical Symbols
Explication des symboles
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
L’éclair avec une flèche à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’une « tension
dangereuse » non isolée à l’intérieur de l’appareil, pouvant être suffisamment élevée pour constituer un risque d’électrocution.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.
Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’instructions
importantes sur l’emploi ou la maintenance (réparation) de l’appareil dans la documentation fournie.
IMPORTANT SAFETY
INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from
the apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been
dropped.
(UL60065_03)
PRÉCAUTIONS CONCER-
NANT LA SÉCURITÉ
1 Lire ces instructions.
2 Conserver ces instructions.
3 Tenir compte de tous les avertissements.
4 Suivre toutes les instructions.
5 Ne pas utiliser ce produit à proximité d’eau.
6 Nettoyer uniquement avec un chiffon propre et sec.
7 Ne pas bloquer les orifices de ventilation. Installer l’appareil
conformément aux instructions du fabricant.
8 Ne pas installer l’appareil à proximité d’une source de chaleur comme
un radiateur, une bouche de chaleur, un poêle ou tout autre appareil
(y compris un amplificateur) produisant de la chaleur.
9 Ne pas modifier le système de sécurité de la fiche polarisée ou de la
fiche de terre. Une fiche polarisée dispose de deux broches dont une
est plus large que l’autre. Une fiche de terre dispose de deux broches
et d’une troisième pour le raccordement à la terre. Cette broche plus
large ou cette troisième broche est destinée à assurer la sécurité de
l’utilisateur. Si la fiche équipant l’appareil n’est pas compatible avec
les prises de courant disponibles, faire remplacer les prises par un
électricien.
10 Acheminer les cordons d’alimentation de sorte qu’ils ne soient pas
piétinés ni coincés, en faisant tout spécialement attention aux fiches,
prises de courant et au point de sortie de l’appareil.
11 Utiliser exclusivement les fixations et accessoires spécifiés par le
fabricant.
12 Utiliser exclusivement le chariot, le stand, le trépied,
le support ou la table recommandés par le fabricant
ou vendus avec cet appareil. Si l’appareil est posé
sur un chariot, déplacer le chariot avec précaution
pour éviter tout risque de chute et de blessure.
13 Débrancher l’appareil en cas d’orage ou lorsqu’il doit
rester hors service pendant une période prolongée.
14 Confier toute réparation à un personnel qualifié. Faire réparer
l’appareil s’il a subi tout dommage, par exemple si la fiche ou le
cordon d’alimentation est endommagé, si du liquide a coulé ou des
objets sont tombés à l’intérieur de l’appareil, si l’appareil a été exposé
à la pluie ou à de l’humidité, si l’appareil ne fonctionne pas
normalement ou est tombé.
(UL60065_03)
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ATTENTION :
POUR RÉDUIRE LES RISQUES D'ÉLECTROCUTION, NE PAS RETIRER
LE CAPOT (OU LE DOS). NE CONTIENT PAS DE PIÈCES NÉCESSITANT
L'INTERVENTION DE L'UTILISATEUR. POUR TOUTE INTERVENTION,
FAIRE APPEL À DES PROFESSIONNELS QUALIFIÉS.
ATTENTION
RISQUE DE CHOC
ELECTRIQUE-NE PAS OUVRIR
The above warning is located on the top of the unit.
L’avertissement ci-dessus est situé sur le dessus de l’unité.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
AVERTISSEMENT
POUR RÉDUIRE LES RISQUES DINCENDIE OU DE DÉCHARGE
ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À
L’HUMIDITÉ.
RMio64-D Owner’s Manual
3
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions con-
tained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted
by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories
and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with
the requirements listed in FCC Regulations, Part 15 for Class “B”
digital devices. Compliance with these requirements provides a
reasonable level of assurance that your use of this product in a
residential environment will not result in harmful interference with
other electronic devices. This equipment generates/uses radio
frequencies and, if not installed and used according to the instruc-
tions found in the users manual, may cause interference harmful
to the operation of other electronic devices. Compliance with FCC
regulations does not guarantee that interference will not occur in
all installations. If this product is found to be the source of interfer-
ence, which can be determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem by using one of the fol-
lowing measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker
or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type
of product. If you can not locate the appropriate retailer, please
contact Yamaha Corporation of America, Electronic Service Divi-
sion, 6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed
by Yamaha Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
FCC INFORMATION (U.S.A.)
* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : Audio Interface
Model Name : RMio64-D
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference
that may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
(FCC DoC)
이 기기는 가정용 (B 급 ) 전자파적합기기로서 주로
가정에서 사용하는 것을 목적으로 하며 , 모든
지역에서 사용할 수 있습니다 .
(class b korea)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The
wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW : EARTH
BLUE : NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead of this apparatus may not cor-
respond with the coloured markings identifying the terminals in your plug
proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be connected to the
terminal in the plug which is marked by the letter E or by the safety earth
symbol or colored GREEN or GREEN-and-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which
is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal
which is marked with the letter L or coloured RED.
(3 wires)
In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.
In Norway: Apparatet må tilkoples jordet stikkontakt.
In Sweden: Apparaten skall anslutas till jordat uttag.
(class I hokuo)
RMio64-D Owner’s Manual
4
Contents
Introduction 7
Features .................................................................7
Precautions for Rack Mounting..............................7
Firmware Updates..................................................7
Conventions in this Manual....................................7
Controls and Functions 8
Front Panel .............................................................8
Rear Panel..............................................................9
Connection 11
About Dante .........................................................11
Notes Regarding the Use of Network Switches...11
Connecting Dante-compatible Devices...............11
Connecting MADI-compatible Devices ...............12
Connecting AC Power..........................................13
Power on and off ..................................................13
Dante Network Settings and Audio Routing ........14
Selecting MADI Input Rate...................................14
Panel Lock ...........................................................14
Signal Flow 14
Dante to MADI......................................................14
MADI to Dante......................................................14
MADI Split ............................................................14
Word Clock 15
About Word Clock................................................15
Selecting a Word Clock Source...........................15
MADI SRC (Sampling Rate Converter) 15
Setting Examples .................................................15
Displaying the MADI Input and Output Signals...16
Remote Control 16
Remote Controllable Parameters .........................16
Control from NUAGE Workgroup Manager..........16
Direct Monitoring 17
RMio64-D Setup 17
Troubleshooting 17
Updating ............................................................. 17
Routing / Patching............................................... 18
Remote Control ................................................... 18
Other Issues ........................................................ 18
Restoring Factory Settings.................................. 18
Index 19
Specifications (at the end of the book)
Included Accessories
Owner’s Manual
AC power cord (European model includes two
different cords.)
RMio64-D Owner’s Manual
5
PRECAUTIONS
PLEASE READ CAREFULLY
BEFORE PROCEEDING
Please keep this manual in a safe place for
future reference.
WARNING
Always follow the basic precautions listed below to avoid
the possibility of serious injury or even death from
electrical shock, short-circuiting, damages, fire or other
hazards. These precautions include, but are not limited
to, the following:
Power supply/power cord
Do not place the power cord near heat sources such as
heaters or radiators, and do not excessively bend or otherwise
damage the cord, place heavy objects on it, or place it in a
position where anyone could walk on, trip over, or roll anything
over it.
Only use the voltage specified as correct for the device. The
required voltage is printed on the name plate of the device.
Use only the supplied power cord/plug.
If you intend to use the device in an area other than in the one
you purchased, the included power cord may not be
compatible. Please check with your Yamaha dealer.
Check the electric plug periodically and remove any dirt or
dust which may have accumulated on it.
Be sure to connect to an appropriate outlet with a protective
grounding connection. Improper grounding can result in
electrical shock, damage to the device(s), or even fire.
Do not open
This device contains no user-serviceable parts. Do not open
the device or attempt to disassemble the internal parts or
modify them in any way. If it should appear to be
malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
Water warning
Do not expose the device to rain, use it near water or in damp
or wet conditions, or place on it any containers (such as
vases, bottles or glasses) containing liquids which might spill
into any openings. If any liquid such as water seeps into the
device, turn off the power immediately and unplug the power
cord from the AC outlet. Then have the device inspected by
qualified Yamaha service personnel.
Never insert or remove an electric plug with wet hands.
Fire warning
Do not put burning items, such as candles, on the unit.
A burning item may fall over and cause a fire.
If you notice any abnormality
When one of the following problems occur, immediately turn
off the power switch and disconnect the electric plug from the
outlet. Then have the device inspected by Yamaha service
personnel.
- The power cord or plug becomes frayed or damaged.
- It emits unusual smells or smoke.
- Some object has been dropped into the device.
- There is a sudden loss of sound during use of the device.
If this device should be dropped or damaged, immediately
turn off the power switch, disconnect the electric plug from the
outlet, and have the device inspected by qualified Yamaha
service personnel.
CAUTION
Always follow the basic precautions listed below to avoid
the possibility of physical injury to you or others, or
damage to the device or other property. These
precautions include, but are not limited to, the following:
Power supply/power cord
When removing the electric plug from the device or an outlet,
always hold the plug itself and not the cord. Pulling by the
cord can damage it.
Remove the electric plug from the outlet when the device is
not to be used for extended periods of time, or during
electrical storms.
Location
Do not place the device in an unstable position where it might
accidentally fall over.
Do not block the vents. This device has ventilation holes at the
front/rear to prevent the internal temperature from becoming
too high. In particular, do not place the device on its side or
upside down. Inadequate ventilation can result in overheating,
possibly causing damage to the device(s), or even fire.
Do not place the device in a location where it may come into
contact with corrosive gases or salt air. Doing so may result in
malfunction.
Before moving the device, remove all connected cables.
When setting up the device, make sure that the AC outlet you
are using is easily accessible. If some trouble or malfunction
occurs, immediately turn off the power switch and disconnect
the plug from the outlet. Even when the power switch is turned
off, electricity is still flowing to the product at the minimum
level. When you are not using the product for a long time,
make sure to unplug the power cord from the wall AC outlet.
If the device is mounted in an EIA standard rack, carefully
read the section “Precautions for Rack Mounting” on page 7.
Inadequate ventilation can result in overheating, possibly
causing damage to the device(s), malfunction, or even fire.
Connections
Before connecting the device to other devices, turn off the
power for all devices. Before turning the power on or off for all
devices, set all volume levels to minimum.
PA_en_4 1/2
RMio64-D Owner’s Manual
6
Maintenance
Remove the power plug from the AC outlet when cleaning the
device.
Handling caution
Avoid inserting or dropping foreign objects (paper, plastic,
metal, etc.) into any gaps or openings on the device (vents,
etc.) If this happens, turn off the power immediately and
unplug the power cord from the AC outlet. Then have the
device inspected by qualified Yamaha service personnel.
Do not rest your weight on the device or place heavy objects
on it, and avoid use excessive force on the buttons, switches
or connectors.
NOTICE
To avoid the possibility of malfunction/ damage to the product,
damage to data, or damage to other property, follow the notices
below.
Handling and Maintenance
Do not use the device in the vicinity of a TV, radio, stereo
equipment, mobile phone, or other electric devices.
Otherwise, the device, TV, or radio may generate noise.
Do not expose the device to excessive dust or vibration, or
extreme cold or heat (such as in direct sunlight, near a heater,
or in a car during the day), in order to prevent the possibility of
panel disfiguration, unstable operation, or damage to the
internal components.
Do not place vinyl, plastic or rubber objects on the device,
since this might discolor the panel.
When cleaning the device, use a dry and soft cloth. Do not
use paint thinners, solvents, cleaning fluids, or chemical-
impregnated wiping cloths.
Condensation can occur in the device due to rapid, drastic
changes in ambient temperature — when the device is moved
from one location to another, or air conditioning is turned on or
off, for example. Using the device while condensation is
present can cause damage. If there is reason to believe that
condensation might have occurred, leave the device for
several hours without turning on the power until the
condensation has completely dried out.
Always turn the power off when the device is not in use.
Information
About functions/data bundled with the product
This product uses Dante Brooklyn II.
Refer to the Audinate website (English) for details on the open
source licenses for the particular software.
https://www.audinate.com/software-licensing
About copyrights
Copying of the commercially available musical data including
but not limited to MIDI data and/or audio data is strictly
prohibited except for your personal use.
About this manual
The illustrations and screens as shown in this manual are for
instructional purposes only.
Windows is a registered trademark of Microsoft
®
Corporation
in the United States and other countries.
The company names and product names in this manual are
the trademarks or registered trademarks of their respective
companies.
(weee_eu_en_01)
(rear_en_01)
European Models
Inrush Current based on EN 55103-1:2009
2.0 A (on initial switch-on)
2.0 A (after a supply interruption of 5s)
Conforms to Environments: E1, E2, E3 and E4
Yamaha cannot be held responsible for damage caused by
improper use or modifications to the device, or data that is
lost or destroyed.
Information for Users on Collection and
Disposal of Old Equipment
This symbol on the products, packaging, and/
or accompanying documents means that used
electrical and electronic products should not
be mixed with general household waste.
For proper treatment, recovery and recycling of
old products, please take them to applicable
collection points, in accordance with your national
legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to
save valuable resources and prevent any potential negative
effects on human health and the environment which could
otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old
products, please contact your local municipality, your waste
disposal service or the point of sale where you purchased
the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment,
please contact your dealer or supplier for further
information.
[Information on Disposal in other Countries outside
the European Union]
This symbol is only valid in the European Union. If you wish
to discard these items, please contact your local authorities
or dealer and ask for the correct method of disposal.
The model number, serial number, power requirements, etc.,
may be found on or near the name plate, which is at the top of
the unit. You should note this serial number in the space pro-
vided below and retain this manual as a permanent record of
your purchase to aid identification in the event of theft.
Model No.
Serial No.
PA_en_4 1/2
RMio64-D Owner’s Manual
7
Introduction
Thank you for choosing the Yamaha RMio64-D audio
interface.
To take full advantage of the superior functions and
performance offered by the RMio64-D, and to enjoy
years of trouble-free use, be sure to read this owner’s
manual carefully before operation.
Features
The RMio64-D is a digital interface that lets you transfer
up to 64 digital inputs and 64 digital outputs between a
Dante network and a MADI-compatible device. By
connecting both Dante and MADI, this product can be
used for wide variety of applications such as
broadcasting, live recording, and post production. In
addition, full control of this unit’s settings has been
achieved through tight integration with Yamaha’s Dante
compatible devices.
Supports redundancy for both Dante and MADI, and
provides a high level of reliability.
Sampling rate converter (SRC) in MADI inputs and
outputs.
Signals can be looped back from MADI optical to
coaxial, or from coaxial to optical (MADI split).
Enhanced linkage functionality with Steinberg
Nuendo, such as direct monitoring and high-precision
clock sync with Nuendo SyncStation.
Precautions for Rack
Mounting
This unit is rated for operation at ambient temperatures
ranging from 0 to 40 degrees Celsius. When mounting
the unit with other RMio unit(s) or other device(s) in an
EIA standard equipment rack, internal temperatures can
exceed the specified upper limit, resulting in impaired
performance or failure. When rack mounting the unit,
always observe the following requirements to avoid heat
buildup:
When mounting the unit in a rack with devices such as
power amplifiers that generate a significant amount of
heat, leave more than 1U of space between the RMio
and other equipment. Also either leave the open
spaces uncovered or install appropriate ventilating
panels to minimize the possibility of heat buildup.
To ensure sufficient airflow, leave the rear of the rack
open and position it at least 10 centimeters from walls
or other surfaces. If you’ve installed a fan kit, there
may be cases in which closing the rear of the rack will
produce a greater cooling effect. Refer to the rack
and/or fan unit manual for details.
Firmware Updates
This product enables you to update the unit firmware to
improve operations, add functions, and correct possible
malfunctions. The following two types of firmware are
available for the unit:
•Units firmware
Dante module firmware
You must update each type of firmware separately.
Details on updating the firmware are available on the
following website:
http://www.yamahaproaudio.com/
For information on updating the unit, refer to the firmware
update guide available on the website.
NOTE
It is necessary to update multiple devices depending on the
version of each device in the Dante network. For details, refer to
the firmware compatibility available on the website.
http://www.yamahaproaudio.com/
Conventions in this Manual
Screen Shots
The example screen shots shown in this manual are from
the Windows version, while those for Steinberg Nuendo
are from Nuendo 6.5. Therefore, the actual displays
might appear different if you are using a different version
of Nuendo. For details, see the Owner’s Manual (PDF)
from the “Help” menu in Nuendo.
RMio64-D Owner’s Manual
8
Controls and Functions
Front Panel
MADI [SRC ON] indicator
MADI [SRC ON] key
Turns the MADI SRC (Sampling Rate Converter) on
(indicator lights) and off.
MADI [SRC WCLK IN] indicator
MADI [SRC WCLK IN] key
Selects whether the word clock that is input to the
MADI [WCLK IN FOR SRC] connector on the rear
panel is used or not as the reference MADI SRC
clock. (Indicator lights when used.)
If no valid word clock input is detected, this indicator
flashes.
MADI [INPUT RATE Fs 44.1kHz] indicator
MADI [INPUT RATE Fs 48kHz] indicator
These indicators turn on accordingly when the
device automatically detects the MADI input signal
as 44.1 kHz or 48 kHz. If no valid MADI input signal is
detected, both indicators remain off.
MADI [INPUT RATE 1Fs] indicator
MADI [INPUT RATE 2Fs] indicator
MADI [INPUT RATE 4Fs] indicator
MADI [INPUT RATE] 1Fs/2Fs/4Fs key
Selects 1Fs (1x), 2Fs (2x), or 4Fs (4x) in combination
with the MADI input rate. For example, for a MADI
input rate of 192 kHz (4x 48 kHz), confirm that the
MADI [INPUT RATE Fs 48kHz] indicator is on, and
then select [4Fs].
NOTE
If you select [2Fs], the unit automatically detects the MADI
input signal frame format (48 kHz/96 kHz).
MADI [STATUS INPUT] indicator
MADI [STATUS OUTPUT] indicator
MADI [STATUS] INPUT/OUTPUT key
Selects whether to display the MADI input signal or
MADI output signal information (frame format/
number of channels).
NOTE
You can use this key to lock the panel to prevent operation
of the keys (page 14).
MADI [STATUS FRAME 48k] indicator
MADI [STATUS FRAME 96k] indicator
Displays the frame format of the MADI input signal or
output signal. For 44.1 kHz and 48 kHz, the [STATUS
FRAME 48k] indicator is lit. For 88.2 kHz and 96 kHz,
the [STATUS FRAME 96k] indicator is lit. If no valid
MADI input signal is detected, both indicators remain
off.
NOTE
If no valid MADI input signal is detected, the MADI output
signal is set to 48 kHz/64 channels.
MADI [STATUS CHANNEL 64] indicator
MADI [STATUS CHANNEL 56] indicator
Displays the number of channels (64 or 56) for the
MADI input signal or output signal. If no valid MADI
input signal is detected, both indicators remain off.
NOTE
If no valid MADI input signal is detected, the MADI output
signal is set to 48 kHz/64 channels.
WORD CLOCK [WCLK IN] indicator
WORD CLOCK [MADI] indicator
WORD CLOCK [DANTE] indicator
WORD CLOCK WCLK IN/MADI/DANTE key
Selects the word clock source.
WCLK IN Uses the word clock signal that is input
from the [WORD CLOCK IN] connector
on the rear panel. This indicator flashes if
no valid word clock input is detected.
MADI Uses the word clock of the MADI input
signal. This indicator flashes if no valid
word clock input is detected.
DANTE Uses the word clock from the Dante
network.
RMio64-D Owner’s Manual
9
WORD CLOCK [Fs] indicator
Displays the word clock frequency that the unit is
using. This indicator flashes if no word clock is
synced.
Dante [SYSTEM] indicator
Displays the operating status of the unit.
Dante [SYNC] indicator
Displays the sync status between the Dante network
and this unit.
[EXTERNAL CONTROL] indicator
This indicator turns on when a parameter which can
be operated only from an external remote control is
effective.
For details about parameters that can be operated
by remote control, see “Remote Control” (page 16).
Power indicator
[I]/[ ] (Power Switch)
Turns power of the unit to on [ ] or off [ ].
The indicator turns on when AC power is on.
CAUTION
Even when the power switch is turned off, a small
amount of current is flowing through the unit. When you
are not using the product for a long time, make sure to
unplug the power cord from the AC outlet.
NOTE
Rapidly turning the unit on and off in succession can cause
it to malfunction. After turning the unit off, wait for at least 6
seconds before turning it on again.
Rear Panel
AC IN connector
Connect the supplied AC power cord here. First
connect the AC power cord to the RMio unit, then
insert the power cord plug into an AC power outlet.
The supplied AC power cord features a V-lock
mechanism via a latch, which prevents the power
cord from coming off accidentally.
Insert the cable plug all the way until it locks in
securely.
CAUTION
Be sure to turn the power off before connecting or
disconnecting the power cord.
Press the latch button on the plug to disconnect the
power cord.
Dante [PRIMARY] connector
Dante [SECONDARY] connector
These are etherCON (RJ-45) connectors for
connecting to the Dante network.
NOTE
Use STP (Shielded Twisted Pair) cable to prevent
electromagnetic interference. Make sure that the metal
parts of the plugs are electrically connected to the STP
cable shield by conductive tape or comparable means.
Connect only Dante-compatible devices or GbE-
compatible devices (including a computer).
Cables of up to 100 meters (theoretical value) can be
used.
Green
(indicator lights)
The unit is working properly.
Green
(indicator flashes)
The firmware updating is in
progress.
Red
(indicator lights)
The memory on the unit does not
work properly.
Red
(indicator flashes)
An error has occurred in the Dante
module.
Green
(indicator lights)
The device is working as the slave
on the Dante network.
Green
(indicator flashes)
The device is working as the
master on the Dante network.
Orange
(indicator lights)
Synchronization with the Dante
network is in progress.
Orange
(indicator flashes)
The device is not synchronized
with the Dante network.
RMio64-D Owner’s Manual
10
Dante [PRIMARY LINK/ACT] indicator
Dante [PRIMARY 1G] indicator
Dante [SECONDARY LINK/ACT] indicator
Dante [SECONDARY 1G] indicator
Displays the transmission status with the Dante
network.
Dante [UNIT ID] rotary switch
Sets the ID for this unit. The setting range of the UNIT
ID is 16 hexadecimal numbers from 0 to F. If there are
multiple Dante-compatible devices from Yamaha that
require an ID setting connected to the same network,
set a different ID for each device. Make sure to
change the settings of the rotary switch while the
power to the unit is turned off; otherwise, the ID
setting will not be effective.
Dante DIP switches
Used to change unit settings. Make sure to change
the settings of the DIP switches while the power to
the unit is turned off; otherwise, the ID setting will not
be effective. For details, see “Connecting Dante-
compatible Devices” (page 11) and “Restoring
Factory Settings” (page 18).
[SYSTEM LINK OUT] connector
This BNC connector is used to connect to the AES 2
IN connector on the Steinberg Nuendo SyncStation.
This connection provides a highly precise clock sync
between this unit and Nuendo.
When not connecting with Nuendo SyncStation, two
of the channels for the Dante input signals are output
as AES/EBU signals. Connecting the AES/EBU-
compatible devices to this connector allows Dante
signals to be converted to AES/EBU signals and can
be output. In the default settings, Dante channels 1
and 2 are used for output. You can use a remote
control to change the output channels. For details,
see “Remote Control” (page 16).
[WORD CLOCK OUT] connector
[WORD CLOCK IN] connector
These are BNC connectors used to transmit and
receive word clock signals.
MADI DIP switches
Used to change unit settings. Make sure to change
the settings of the DIP switches while the power to
the unit is turned off; otherwise, the ID setting will not
be effective. For details, see “Connecting MADI-
compatible Devices” (page 12) and “MADI Split”
(page 14).
MADI [WCLK IN FOR SRC] connector
This is a BNC connector that can be used to directly
input word clock signals for MADI SRC.
MADI [COAXIAL OUT] connector
MADI [COAXIAL IN] connector
These are BNC connectors used to connect with
MADI-compatible devices.
NOTE
Coaxial cables of up to 100 meters (theoretical value) can
be used.
MADI [OPTICAL OUT] connector
MADI [OPTICAL IN] connector
These are SC connectors used to connect with
MADI-compatible devices.
NOTE
Use a multimode optical cable with 50-micron core/125-
micron cladding diameters, or 62.5-micron core/125-
micron cladding diameters.
Optical cables of up to 2,000 meters (theoretical value)
can be used.
Use SC duplex connectors.
Attach the supplied rubber cap to the connector to
prevent dust from collecting when the cable is not
connected.
LINK/ACT These indicators flash rapidly if the
Ethernet cables are connected properly.
1G These indicators are lit when the Dante
network is functioning as Giga-bit
Ethernet.
RMio64-D Owner’s Manual
11
Connection
This section describes the following connections.
About Dante
Dante is a network audio protocol developed by
Audinate. It is designed to deliver multi-channel audio
signals at various sampling and bit rates, as well as
device control signals over a Giga-bit Ethernet (GbE)
network.
Visit the Audinate website for more details on Dante:
http://www.audinate.com/
More information on Dante is also posted on the Yamaha
Pro Audio website:
http://www.yamahaproaudio.com/
Notes Regarding the Use of
Network Switches
Do not use the EEE functionality (*) of network switches
on a Dante network.
Although mutual power consumption settings between
switches that support the EEE functionality are adjusted
automatically, there are some switches for which such
mutual settings are not adjusted correctly.
This may cause EEE to be enabled in Dante networks
when it is not appropriate, resulting in poor
synchronization performance and occasional dropouts.
Therefore we strongly recommend the following.
If you use managed switches, please disable the EEE
functionality. Do not use switches that prevent EEE
functionality from being disabled.
When using unmanaged switches, do not use
switches that support EEE functionality. EEE
functionality cannot be disabled for such switches.
* EEE (Energy Efficient Ethernet) is a technology that reduces
switch power consumption during periods of low network
traffic. It is also referred to as Green Ethernet and
IEEE802.3az.
Connecting Dante-compatible
Devices
You can connect the RMio64-D to a Dante network in the
following ways.
Daisy Chain Network
A daisy chain network is a wiring scheme in which
multiple devices are connected together in sequence.
This connection method is suitable for a simple system
with a small number of devices.
However, if a large number of devices are connected,
you will also need to manually increase the latency value
significantly. Also, if a connection is broken in a daisy
chain network, the signal flow is interrupted at that point
and no signal will be transferred beyond that point.
Settings
Turn off Dante DIP switch 1 (UP).
If there are multiple Dante-compatible devices from
Yamaha that require an ID setting connected to the
same network, set a different ID for each device. Make
sure to change the settings of the rotary switch while
the power to the unit is turned off; otherwise, the ID
setting will not be effective.
Connecting Dante-compatible Devices (page 11)
Connecting MADI-compatible Devices (page 12)
Connecting AC Power (page 13)
Dante Audio Routing (page 14)
Selecting MADI Input Rate (page 14)
CL5
Rio3224-D (ID#1)
RMio64-D (ID#2)
PRIMARY
SECONDARY
PRIMARY
RMio64-D Owner’s Manual
12
Star Network
In a star network, each device is connected to a central
GbE-compatible network switch. This connection
enables you to configure a wide-band, large-scale
network.
Settings
Turn on Dante DIP switch 1 (DOWN).
If there are multiple Dante-compatible devices from
Yamaha that require an ID setting connected to the
same network, set a different ID for each device. Make
sure to change the settings of the rotary switch while
the power to the unit is turned off; otherwise, the ID
setting will not be effective.
NOTE
We recommend a network switch that features various
functions for controlling and monitoring the network (such as
QoS).
Do not use the EEE functionality of network switches.
Star Network (Redundant Network)
You can set up a star network redundant so that there is
no audio loss even if interference occurs on the network.
A redundant network consists of two circuits, a primary
circuit and a secondary circuit. Normally, the network
operates on the primary circuit. However, if the primary
connection is broken, the secondary circuit will
automatically take over communications.
Settings
Turn on Dante DIP switch 1 (DOWN).
If there are multiple Dante-compatible devices from
Yamaha that require an ID setting connected to the
same network, set a different ID for each device. Make
sure to change the settings of the rotary switch while
the power to the unit is turned off; otherwise, the ID
setting will not be effective.
NOTE
We recommend a network switch that features various
functions for controlling and monitoring the network (such as
QoS).
Do not use the EEE functionality of network switches.
The Dante [SYNC] indicator flashes as follows when
communication error occurs on the Dante Redundant
Network.
Connecting MADI-compatible
Devices
You can connect the RMio64-D to MADI-compatible
devices using either 75Ω coaxial (BNC) or optical (SC)
cables.
Using 75Ω Coaxial Cables
NOTE
Coaxial cables of up to 100 meters (theoretical value) can be
used.
Error on a primary network
Error on a secondary network
Light or
flash
(green)
Flashes
once
(orange)
Light or
flash
(green)
Flashes
twice
(orange)
Computer
Network switch A
Network switch B
Primary Dante
Secondary Dante
CL5
Rio3224-D (ID#1)
RMio64-D (ID#2)
MADI-compatible device
RMio64-D
COAXIAL
OUT
COAXIAL
IN
COAXIAL
OUT
COAXIAL
IN
RMio64-D Owner’s Manual
13
Using Optical Cables
NOTE
Optical cables of up to 2,000 meters (theoretical value) can be
used.
Redundant Connection (Input only)
You can set up a redundant connection using both 75Ω
coaxial cables and optical cables, so that there is no
input signal loss even if interference occurs in the
connection.
In addition, the input signal from the Dante network is
output from both the MADI [COAXIAL OUT] and MADI
[OPTICAL OUT] connectors, regardless of the MADI
redundancy settings.
Settings
To set up a redundant connection, turn on MADI DIP
switch 2 (DOWN).
To give priority to the coaxial cables, turn on MADI DIP
switch 1 (DOWN).
To give priority to the optical cables, turn off MADI DIP
switch 1 (UP).
NOTE
Make sure to change the settings of the DIP switches while the
power to the unit is turned off; otherwise, the ID setting will not
be effective.
When using the word clock input from the MADI [WCLK
IN FOR SRC] connector as the MADI SRC reference
clock, the redundant function is unavailable.
Connecting AC Power
1. Turn the unit off.
2. Connect the plug on the AC power cord to
the AC IN connector on the rear panel of the
unit.
3. Connect the other side of the plug on the
AC power cord to a power supply socket.
NOTE
When removing the AC power cord, perform these steps in
reverse.
Press the latch button on the plug to disconnect the power
cord.
WARNING
The RMio64-D has been designed assuming it a proper
ground connection is used. To prevent electrical shock
and damage to devices, use the included AC power cord
to create a secure ground connection. If you do not know
how to make a proper ground connection, contact a
Yamaha service center listed at the end of this manual.
Be sure to use only the included power cord with this unit.
Use of a different power cord could result in abnormal
heat and electrical shock.
CAUTION
Be sure to turn the power off before connecting or
disconnecting the power cord.
Even when the power switch is turned off, a small amount
of current is flowing through the unit. When you are not
using the product for a long time, make sure to unplug the
power cord from the power supply outlet.
Power on and off
When turning on the AC power in your audio system,
always turn on the power amplifier LAST, to avoid
speaker damage. When turning the power off, the power
amplifier should be turned off FIRST for the same
reason.
MADI-compatible device
RMio64-D
OPTICAL
OUT
OPTICAL
IN
OPTICAL
OUT
OPTICAL
IN
MADI-compatible device
Coaxial cable
priority
Optical cable
priority
RMio64-D
RMio64-D Owner’s Manual
14
Dante Network Settings and
Audio Routing
With the Dante network, you can route the audio input
and output of multiple Dante devices in any way you like.
This requires you to set which channel signals are sent
to which inputs. The routing for connecting MADI with
the Dante network is fixed on the RMio64-D. Therefore,
any changes in routing are made in the Dante network.
Use Dante Controller to configure the audio routing of
the Dante network.
You can download Dante Controller from the following
website:
http://www.yamahaproaudio.com/
Refer to the Dante Controller owner’s manual (available
from the same website) for details about Dante
Controller.
Selecting MADI Input Rate
Use the MADI [INPUT RATE] 1Fs/2Fs/4Fs keys on the
front panel to select the MADI input rate.
For example, for a MADI input rate of 192 kHz (4x 48
kHz), confirm that the MADI [INPUT RATE Fs 48kHz]
indicator is on, and then select [4Fs]. If no valid MADI
input signal is detected, both indicators remain off.
Panel Lock
You can lock the panel to prevent unintended changes
and operations. While the lock is engaged, all controllers
on the front panel are inoperable. To engage the lock,
press and hold the MADI [STATUS] INPUT/OUTPUT key
for at least 3 seconds. All front panel indicators (except
the power indicator) flash, indicating all controllers are
locked. To disengage the lock, press and hold the MADI
[STATUS] INPUT/OUTPUT key for at least 3 seconds.
NOTE
Even if the front panel is locked, you can use remote control to
make changes to the settings.
For the latest information about remote control compatible
devices, refer to the Yamaha Pro Audio website:
http://www.yamahaproaudio.com/
Signal Flow
Dante to MADI
The Dante input signal is output from the MADI
[COAXIAL OUT] connector and the [OPTICAL OUT]
connector.
MADI to Dante
The MADI input signal is output from the Dante
[PRIMARY] and [SECONDARY] connectors.
MADI Split
A signal that is input via coaxial or optical connector can
be looped back via the other connector. When doing so,
the signal also goes to the Dante network.
Settings
To use a MADI split, turn on MADI DIP switch 3
(DOWN).
To loop back the input signal from the MADI [COAXIAL
IN] connector to the MADI [OPTICAL OUT] connector,
turn on MADI DIP switch 1 (DOWN).
To loop back the input signal from the MADI [OPTICAL
IN] connector to the MADI [COAXIAL OUT] connector,
turn off MADI DIP switch 1 (UP).
NOTE
Make sure to change the settings of the DIP switches while the
power to the unit is turned off; otherwise, the ID setting will not
be effective.
3 seconds
RMio64-D Owner’s Manual
15
Word Clock
About Word Clock
You can set the word clock source to an external clock
device, the MADI input signal, or the Dante network.
You can send the word clock from this unit to an
external device via the [WORD CLOCK OUT]
connector.
You can connect the [SYSTEM LINK OUT] connector
to the AES 2 IN connector on Steinberg Nuendo
SyncStation for high-precision clock sync with
Nuendo.
Selecting a Word Clock
Source
Use the WORD CLOCK [WCLK IN]/[MADI]/[DANTE] key
on the front panel to select the word clock source.
The unit’s clock is synced with the selected word clock
source.
NOTE
If you select [WCLK IN] or [MADI], the unit is automatically
specified as the “Preferred Master” and “Enable Sync To
External” is set in the Dante network.
If you select [WCLK IN] or [MADI], when the unit acts as the
clock slave on the Dante network, input to the unit the same
clock as the clock master. You can use Dante Controller
(available from the following website) to check which device
is the current clock master.
http://www.yamahaproaudio.com/
If the word clock signal from the selected work clock source is
cut off, the unit switches to its internal clock. The internal
clock operates according to the previous word clock, before it
was cut off.
MADI SRC (Sampling
Rate Converter)
MADI SRC allows you to connect a MADI-compatible
device having a different clock than the RMio64-D unit.
You can connect a Dante network and a MADI-
compatible device that are operating under different
clocks without making any changes to either clock.
You can output MADI signals with a different word
clock than the MADI input signal.
Setting Examples
NOTE
Output Clock Source in the following block diagram can be
controlled only by remote control.
Using the MADI signal internal clock on the
MADI side, and syncing the unit to the
Dante network:
Using an external clock on the MADI-
compatible devices, and syncing the unit to
the Dante network:
NOTE
The same external clock supplied to MADI-compatible devices
must be input to [WCLK IN FOR SRC] on the unit.
WCLK IN Uses the word clock signal that is input from
the [WORD CLOCK IN] connector on the
rear panel. This indicator flashes if no valid
word clock input is detected.
MADI Uses the word clock of the MADI input
signal. This indicator flashes if no valid word
clock input is detected.
DANTE Uses the word clock from the Dante network.
Word Clock Source Input Clock Source Output Clock Source
DANTE
MADI
WCLK IN
DANTE MADI
Clock
WCLK IN
(FOR SRC)
MADI IN
Same as
Input Clock Source
Same as Word
Clock Source
Signal Processing
Signal
SRC
SRC
Word Clock Source Input Clock Source Output Clock Source
DANTE
MADI
WCLK IN
DANTE MADI
Clock
WCLK IN
(FOR SRC)
MADI IN
Same as
Input Clock Source
Same as Word
Clock Source
Signal Processing
Signal
SRC
SRC
RMio64-D Owner’s Manual
16
Syncing the unit to a MADI input signal
NOTE
If the unit acts as the clock slave on the Dante network, input to
the unit the same MADI clock used for the device that is the
clock master. You can use Dante Controller (available from the
following website) to check which device is the current clock
master.
http://www.yamahaproaudio.com/
Using an external clock on MADI-compatible
devices, and syncing the unit to a different
external clock:
NOTE
The same external clock supplied to MADI-compatible
devices must be input to [WCLK IN FOR SRC] on the unit.
If the unit acts as the clock slave on the Dante network, input
to the unit the same external clock used for the device that is
the clock master. You can use Dante Controller (available
from the following website) to check which device is the
current clock master.
http://www.yamahaproaudio.com/
Displaying the MADI Input
and Output Signals
The frame format and number of channels for the MADI
input signal or output signal are displayed in the MADI
[STATUS] area.
Use the MADI [STATUS] INPUT/OUTPUT key to switch
between the input signal display and the output signal
display.
Remote Control
You can use the RMio64-D remote control to configure
items that cannot be configured from the unit’s panel,
such as individual settings for MADI SRC input/output
controls and setting the MADI output to a different format
than the MADI input.
NOTE
For the latest information about remote control compatible
devices, refer to the Yamaha Pro Audio website:
http://www.yamahaproaudio.com/
Remote Controllable
Parameters
Control from NUAGE
Workgroup Manager
When RMio64-D is operating in the NUAGE Workgroup,
you can use remote control to configure the RMio64-D
and use direct monitoring functions.
Word Clock Source Input Clock Source Output Clock Source
DANTE
MADI
WCLK IN
DANTE MADI
Clock
WCLK IN
(FOR SRC)
MADI IN
Same as
Input Clock Source
Same as Word
Clock Source
Signal Processing
Signal
SRC
SRC
Word Clock Source Input Clock Source Output Clock Source
DANTE
MADI
WCLK IN
DANTE MADI
Clock
WCLK IN
(FOR SRC)
MADI IN
Same as
Input Clock Source
Same as Word
Clock Source
Signal Processing
Signal
SRC
SRC
Parameter Description
SRC ON/OFF Turns MADI SRC on or off.
SRC INPUT CLOCK
SOURCE
For selecting the MADI SRC clock
source: the MADI input signal or the
clock input from the WCLK IN FOR
SRC connector.
SRC OUTPUT
CLOCK SOURCE
For selecting the MADI SRC clock
output: the input signal or the unit’s
master clock.
INPUT RATE Displays the frequency when the
MADI input signal is automatically
detected as 44.1 kHz or 48 kHz.
For selecting 1Fs, 2Fs, or 4Fs in
combination with the MADI input
rate.
STATUS INPUT Displays the status of the MADI input
signal.
STATUS OUTPUT Displays the status of the MADI
output signal. You can also make
changes to the frame format and
number of channels for the MADI
output signal.
BNC AES/EBU OUT For selecting the Dante input
channel output from the [SYSTEM
LINK OUT] connector as the AES/
EBU signal.
CLOCK For selecting the source used as the
master clock.
PANEL LOCK Locks the panel to prevent operation
of the unit’s controllers. Default
settings are turned off.
RMio64-D Owner’s Manual
17
Direct Monitoring
When RMio64-D is operating in the NUAGE Workgroup,
a “direct monitoring” function is available. Direct
monitoring allows you to monitor a MADI signal output
from the RMio64-D to Steinberg Nuendo as direct MADI
output, in the same way as NUAGE I/O.
Direct monitoring provides latency-free monitoring of
signals from audio tracks balanced with the faders in
Nuendo and MADI signals routed to the OUTPUT BUS.
To turn direct monitoring on or off, use the monitoring
button on tracks in Nuendo where the RMio64-D is
routed as input ports.
NOTE
To use direct monitoring, you must activate [Direct Monitoring]
in the Nuendo [Device Setup] menu.
RMio64-D Setup
If there are multiple AIC128-D cards on a Dante network,
specify the AIC128-D unit that is used in Nuendo.
To open the RMio64-D Setup within Nuendo, click
“Devices,” then click “RMio64-D Setup.”
Dante Interface
Select the AIC128-D that is used in Nuendo.
Identify
When you click here, the lamp on the selected
AIC128-D flashes for a few seconds. This function is
convenient for identifying the selected AIC128-D.
Reload
When you click here, choices for the Dante interface
are updated to the latest status.
Troubleshooting
The following is an abbreviated list of frequently asked
questions in the past. Please check it if you run into
similar problems and need help.
A mixer does not recognize the RMio64-
D
Is the Dante [Unit ID] set different ID from other Dante-
compatible devices from Yamaha that connected to
the same network?
Is the network switch working properly?
The problem may be solved by turning the network
switch on again.
Is the cable defective?
The problem may be solved by replacing the cable.
Audio cuts out or distorts.
Is the correct MADI input frequency selected?
(page 14)
If [MADI] or [WCLK IN] is selected as the word clock
source, change it to [DANTE]. Keep in mind that if this
remedies the problem, the clocks for the Dante
network and the unit will not be synced. If you want to
select [MADI] or [WCLK IN] as the word clock source,
the unit must be set as the clock master for the Dante
network. For details, refer to the Dante Controller User
Guide available on the website.
http://www.yamahaproaudio.com/
Updating
How to update the firmware?
What are the computer requirements for
updating the firmware?
For information about updating the unit, refer to the
firmware update guide for each product and the
following website.
http://www.yamahaproaudio.com/
Cannot update
The problem may be solved by disabling any antivirus
software and the firewall of the computer.
For other details, refer to the firmware update guide
available on the website.
http://www.yamahaproaudio.com/
What devices should I update?
It is necessary to update multiple devices depending on
the version of each device. For details, refer to the
firmware compatibility available on the website.
http://www.yamahaproaudio.com/
RMio64-D Owner’s Manual
18
Routing / Patching
A mixer is not receiving an input signal
from the RMio64-D
Is the patch of the Dante network set up correctly by
Dante Controller?
Is the patch setting in the mixer set to use the Dante
Controller?
Is the word clock setting in the mixer set to correspond
to the Dante network?
How can the Dante input and output
signals be patched?
Use Dante Controller to configure the audio routing
(patching) of the Dante network. For details, refer to the
Dante Controller User Guide available on the website.
http://www.yamahaproaudio.com/
Is it possible to input a signal from two
RMio64-D units to one channel of the
mixer?
Unlike with output, input can receive only the signal of
one channel.
Is it possible to receive the input signal
from RMio64-D by a separate mixer?
It can be configured using the Dante Controller. For
details, refer to the Dante Controller User Guide
available on the website.
http://www.yamahaproaudio.com/
Remote Control
I want to change the RMio64-D settings
from the mixer
I want to know the devices that can
remotely configure the RMio64-D
For details on RMio64-D remote control, refer to the
following website.
http://www.yamahaproaudio.com/
Other Issues
What is the latency of the Dante
network?
The latency value can be set by Dante Controller or
some mixers. For details, refer to the manuals for each
product.
An internal error message such as
“firmware mismatch” is displayed on
the device connected to the RMio64-D.
Make sure that each device has a compatible version.
For details, refer to the firmware compatibility information
available on the website.
http://www.yamahaproaudio.com/
Restoring Factory Settings
Perform the following steps to restore the factory
settings.
1. Turn the unit off.
2. Turn on Dante DIP switch 2 (DOWN), and
turn the unit on.
All front panel indicators (except the power
indicator) flash, indicating all parameters have
been restored to the factory settings.
3. Turn the unit off.
4. Turn off Dante DIP switch 2 (UP).
5. Turn the unit on again.
RMio64-D Owner’s Manual
19
Index
Numerics
1Fs/2Fs/4Fs .............................................................8, 14
A
AC power cord
Unlock ............................................................. 9, 13
AES/EBU output ...........................................................10
Audio routing .........................................................14, 18
C
Connecting
AC power ............................................................13
Coaxial cables .................................................... 12
Daisy chain network ........................................... 11
Optical cables ....................................................13
Redundant network (Dante) ............................... 12
Redundant network (MADI) ................................13
Star network ........................................................ 12
D
Dante ........................................................................... 11
Daisy chain network ........................................... 11
DIP switch ............................................... 10, 11, 12
Network switch .............................................11, 12
Patching (Audio routing) ............................... 14, 18
Redundant Network ............................................ 12
Star Network .......................................................12
UNIT ID ...................................................10, 11, 12
Direct monitoring .........................................................17
F
Factory Settings ...........................................................18
Firmware ............................................................7, 17, 18
I
Included Accessories ....................................................4
Input rate .................................................................8, 14
L
Latency ........................................................................18
Loop back .................................................................... 14
M
MADI
Coaxial connection ............................................. 12
DIP switch ............................................... 10, 13, 14
Input rate ..................................................8, 14, 16
Loop back ...........................................................14
Optical connection .............................................13
Redundant connection ....................................... 13
MADI Split .................................................................... 14
MADI SRC (Sampling Rate Converter) ........................ 15
N
Network switch ...................................................... 11, 12
P
Panel lock .................................................................... 14
Patching (Audio routing) ........................................ 14, 18
R
Rack mounting ............................................................... 7
Remote control ...................................................... 16, 18
Restoring Factory Settings .......................................... 18
Rotary switch ................................................... 10, 11, 12
Routing .................................................................. 14, 18
S
Signal flow ................................................................... 14
U
Updating .................................................................. 7, 17
W
Word clock ................................................................... 15
Word clock frequency ................................................... 9
Word clock source ................................................... 8, 15
Specifications
General Specifications
*The contents of this manual apply to the latest specifications as of the printing date. Since Yamaha makes continuous improvements to
the product, this manual may not apply to the specifications of your particular product. To obtain the latest manual, access the Yamaha
website then download the manual file. Since specifications, equipment or separately sold accessories may not be the same in every
locale, please check with your Yamaha dealer.
Sampling Frequency
Internal 44.1kHz
48kHz
88.2kHz
96kHz
176.4kHz
192kHz
+4.1667%/+0.1%/-0.1%/-4.0% ±50ppm
+4.1667%/+0.1%/-0.1%/-4.0% ±50ppm
+4.1667%/+0.1%/-0.1%/-4.0% ±50ppm
+4.1667%/+0.1%/-0.1%/-4.0% ±50ppm
+4.1667%/+0.1%/-0.1%/-4.0% ±50ppm
+4.1667%/+0.1%/-0.1%/-4.0% ±50ppm
External 44.1kHz
48kHz
88.2kHz
96kHz
176.4kHz
192kHz
+4.1667%/+0.1%/-0.1%/-4.0% ±200ppm
+4.1667%/+0.1%/-0.1%/-4.0% ±200ppm
+4.1667%/+0.1%/-0.1%/-4.0% ±200ppm
+4.1667%/+0.1%/-0.1%/-4.0% ±200ppm
+4.1667%/+0.1%/-0.1%/-4.0% ±200ppm
+4.1667%/+0.1%/-0.1%/-4.0% ±200ppm
MADI Channels &
Formats
fs=44.1kHz/48kHz: MADI Single fs 44.1/48k frame, 56/64 channels
fs=88.2kHz/96kHz: MADI Double fs 44.1/48k frame, 28/32 channels
MADI Double fs 88.2/96k frame, 28/32 channels
fs=176.4kHz/192kHz: MADI Quad fs 44.1/48k frame, 14/16 channels
SRC
SRC Lock Range: 38.59kHz – 216kHz
Sample Rate Ratio Limit: 6:1
Dimensions (WxHxD)
and Net Weight
480 x 44 x 374 mm, 4.7 kg
Power Requirements
(wattage)
25W
Power Requirements
(voltage and hertz)
US/Canada: 120V 60Hz
Japan: 100V 50/60Hz
China: 110 – 240V 50/60Hz
Korea: 220V 60Hz
Others: 110 – 240V 50/60Hz
Temperature Range
Operating temperature range: 0 – 40 °C
Storage temperature range: -20 – 60 °C
Included Accessories
Owner’s Manual, AC power cord
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34

Yamaha RMio64 Bruksanvisning

Typ
Bruksanvisning