Yamaha CDC-905 Bruksanvisning

Kategori
CD-spelare
Typ
Bruksanvisning
CONTENTS
CAUTION............................................................... 4
CONNECTIONS .................................................... 5
IDENTIFICATION OF COMPONENTS.................. 6
BASIC OPERATION .............................................. 8
RANDOM-SEQUENCE PLAY.............................. 13
PROGRAM PLAY................................................. 14
REPEAT PLAY..................................................... 16
INDEX SEARCH.................................................. 16
CD SYNCHRONIZED RECORDING................... 17
TRACK PROGRAMMING FOR RECORDING
TO TAPE ............................. 18
AUTOMATIC SEARCHING FOR THE PEAK
LEVEL ON A DISC ..............21
NOTES ABOUT THE REMOTE CONTROL
TRANSMITTER ................................................... 22
TIMER PLAY ........................22
NOTES ABOUT HANDLING COMPACT
DISCS.................................................................. 23
TROUBLESHOOTING......................................... 24
SPECIFICATIONS ............................................... 24
TABLE DES MATIERES
ATTENTION......................................................... 26
CONNEXIONS..................................................... 27
IDENTIFICATION DES COMPOSANTS.............. 28
FONCTIONNEMENT DE BASE .......................... 30
LECTURE EN SÉQUENCE ALÉATOIRE............ 35
LECTURE PROGRAMMÉE................................. 36
LECTURE REPETÉE .......................................... 38
RECHERCHE D’INDEX....................................... 38
ENREGISTREMENT SYNCHRONISE D’UN
COMPACT DISQUE
............................................. 39
PROGRAMMATION DES PLAGES POUR
ENREGISTREMENT SUR CASSETTE
...................................... 40
RECHERCHE AUTOMATIQUE DU NIVEAU DE
CRÊTE D’UN DISQUE
.......................................43
REMARQUES CONCERNANT LA
TELECOMMANDE............................................... 44
LECTURE COMMANDÉE PAR
PROGRAMMATEUR
.......................................44
REMARQUES CONCERNANT LA
MANIPULATION DES DISQUES......................... 45
DEPISTAGE DE PANNES................................... 46
CARACTERISTIQUES TECHNIQUES................ 46
NATURAL SOUND COMPACT DISC PLAYER
CHANGEUR AUTOMATIQUE DE COMPACT DISQUES
CDC-905/505
UCA
OWNER’S MANUAL
MODE D’EMPLOI
for CDC-905 only
for CDC-905 only
for CDC-905 only
CDC-905 seulement
CDC-905 seulement
CDC-905 seulement
2
SAFETY INSTRUCTIONS
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the manufacturer.
6A A unit and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
unit and cart combination to overturn.
7 Wall or Ceiling Mounting – The unit should
be mounted to a wall or ceiling only as
recommended by the manufacturer.
8 Ventilation – The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block the
ventilation openings; or placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow
of air through the ventilation openings.
9 Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances that
produce heat.
10 Power Sources – The unit should be connected to a
power supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been
damaged; or
B. Objects have fallen, or liquid has been spilled into the
unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
exhibits a marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located
away from power lines.
18 Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
Explanation of Graphical Symbols
CAUTION
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
IMPORTANT!
Please record the serial number of this unit
in the space below.
Model:
Serial No.:
The serial number is located on the rear of
the unit.
Retain this Owner’s Manual in a safe place
for future reference
3
English
As the laser beam used in this compact disc player is harmful
to the eyes, do not attempt to disassemble the cabinet. Refer
servicing to qualified personel only.
To avoid electrical shock, do not open the unit. Refer
servicing to qualified personnel only.
DANGER: The use of optical instrument with this product will
increase eye hazard.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
DANGER
Invisible laser radiation when open and interlock failed or
defeated.
Avoid direct exposure to beam.
WARNING
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your
sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, YAMAHA
and the Electronic Industries Association’s
Consumer Electronics Group recommend you to
avoid prolonged exposure from excessive
volume levels.
We Want You Listening For A Lifetime
Laser Diode Properties
• Material: GaAlAs
• Wavelength: 780nm
• Emission Duration: continuous
• Laser Output: max. 44.6µW*
* This output is the value measured at a distance of about
200mm from the objective lens surface on the Optical Pick-
up Block.
FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
For Canadian Customers
To prevent electric shock, match wide blade of plug to wide
slot and fully insert.
This Class B digital apparatus complies with Canadian ICES-
003.
4
1 To ensure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install your unit in a cool, dry, clean place, and in a
horizontal and stable position – away from windows, heat
sources, vibration, dust, moisture, or cold. To avoid
humming sounds, locate the unit away from other
electrical appliances, motors, and transformers. To
prevent fire or electrical shock, do not expose to rain and
water.
3 Do not operate the unit upside-down. It may overheat,
possibly causing damage.
4 Never open the cabinet. If a foreign object drops into the
set, contact your dealer.
5 Do not use force on switches, knobs or cords.
6 Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
7 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that your unit
is faulty.
8 Do not place another component on top of this unit,
because to do so will discolor or damage the surface of
the unit.
9 To prevent damage by lightning, disconnect the power
cord from the household AC outlet during an electrical
storm.
10 When disconnecting the power cord from the household
AC outlet, grasp the plug; do not pull the cord.
CAUTION FOR CARRYING THIS UNIT
Be sure not to carry or tip this unit with discs remaining in it.
CAUTION FOR MOVING THIS UNIT
When moving this unit, first remove all discs from the disc tray and
close the tray by pressing the OPEN/CLOSE button. After you
confirm that the display lights up as shown below, switch off the
power by pressing the POWER switch, and then disconnect the
power plug from the AC outlet.
Never switch off the power untill the display lights up as above,
otherwise this unit will break down during moving because the
internal mechanism is not locked.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT
FEATURES
5-Disc Carousel Auto-changer
Full Opening Disc Tray for Changing 5
Discs at a Time
PLAYXCHANGE; Disc Changing
Capability while Playing Another
CD TEXT Compatibility
Random Access Programmable Play
Random-Sequence Play
Single Track/Entire Disc/All Disc Repeat
Play
Adjustable Display Brightness
Remote Control Capability
Disc Scanning Capability Useful for Disc
Searching or Disc Checking
CD Synchronized Recording with a
Compatible YAMAHA Tape Deck
Optical Digital Output
CDC-905 only
Automatic Programming for Recording to
Tape
Timer Play Option
Automatic Peak Level Searching
Capability
Adjusting the Output Level
PHONES jack
DIGITAL INCD
OPTICAL
OPTICAL
DIGITAL
AUDIO
OUT
LINE OUT
1
5
English
CONNECTIONS
Before making any connections, switch OFF the power to
the unit and the amplifier or other components.
Connections should be made to the correct input terminals
of the amplifier or other components.
If the placement of this unit causes noise in other equipment,
such as a tuner, separate them from each other.
Choose one of the ways listed below to connect this unit to your amplifier.
Never plug in this unit and other components until all connections are completed.
Connection cord
(included)
To AC outlet
To AC outlet
Optical fiber cable
(not included)
Amplifier
CDC-505 CDC-905
For Custom Installer
For U.S.A., Canada and Australia models of CDC-905 only
REMOTE CONTROL (IN, OUT) terminals
These terminals are used for custom installation system.
When this unit is connected to the components for custom
installation system, you can operate this unit with the
system remote control.
Connect the REMOTE CONTROL IN terminal of this unit to
the output terminal of the central controller for custom
installation system.
By connecting the REMOTE CONTROL OUT terminal of
this unit to the REMOTE CONTROL IN terminal of the other
component, you can also operate it with the system remote
control. In this way, up to 6 components can be connected
in series.
When the LINE OUT (analog) terminals of this
unit are used (
)
Be sure that the left (“L”) and right (“R”) LINE OUT terminals
are connected to the corresponding (left and right) terminals
of the amplifier or other components.
Connect the “LINE OUT” terminals to the “CD” (or “AUX”)
terminals of the amplifier. If the amplifier does not have
such terminals, use the “TAPE PB” terminals. For additional
details concerning these connections, refer to the operation
instructions for the amplifier being used.
The LINE OUT terminals of this unit are numbered 1. When
connecting this unit with a YAMAHA amplifier or receiver
whose terminals on the rear panel are numbered as 1, 2,
3, etc., connect the LINE OUT terminals of this unit to the
input terminals numbered 1 on the rear of the amplifier or
receiver.
When the DIGITAL AUDIO OUT (OPTICAL)
terminal of this unit is used (
)
Before using this terminal, remove the terminal’s cover by
pulling it.
Make the connection from this terminal to the optical input
terminal of an amplifier by using a commercially available
optical fiber cable.
* Be sure to use a high quality optical fiber cable. Other
cables might not function correctly.
This terminal can also be connected to the optical input
terminal of a digital audio tape deck (DAT), etc. to record CD
onto tape directly.
Be sure to attach the terminal cover when this terminal is not
being used in order to protect the terminal from dust.
CDC-905 only
Set the level of signals output into an amplifier to max. by
using the OUTPUT LEVEL buttons.
6
POWER
5
SKIP/SEARCH
+10
1
2 3 4 5 6 7 8 9 0
PROG
PLAYXCHANGE
OPEN/CLOSE
OUTPUT LEVEL
PHONES
DISC
NATURAL SOUND COMPACT DISC PLAYER
PEAK
/
1 2 3 4
+
IDENTIFICATION OF COMPONENTS
FRONT PANEL
* ( ) indicates the page number on which the control and its function are best described.
* The control functions on the main unit and on the remote
control transmitter are virtually identical, with the exceptions
below.
* The (PLAY/PAUSE) button on the main unit has both
the functions of the PLAY button and the PAUSE button on
the remote control transmitter.
* The SKIP/SEARCH buttons on the main unit have both the
functions of the SKIP button and the SEARCH button on the
remote control transmitter.
NATURAL SOUND COMPACT DISC PLAYER
POWER
5
DISC
1 2 3 4
SKIP/SEARCH
PLAYXCHANGE
OPEN/CLOSE
/
POWER switch (p. 8) PHONES jack (p. 12)
Play/Pause button (p. 8, 9)DISC-select buttons (p. 8)
Remote control sensor (p. 22)
Display panel
PEAK button (p. 21)
SKIP/SEARCH
buttons (p. 10)
POWER switch (p. 8)
Disc tray (p. 8)
Disc tray (p. 8)
PLAYXCHANGE button (p. 9)
Play/Pause button (p. 8, 9)
Display panel DISC-select buttons (p. 8) SKIP/SEARCH buttons (p. 10)Remote control sensor (p. 22)
PLAYXCHANGE button (p. 9)
CDC-505
CDC-905
7
English
CDC-905 only
CDC-905 only
REMOTE CONTROL TRANSMITTER
CLEAR button (p. 15)
OPEN/CLOSE button (p. 8)
PROG button (p. 14)
Numeric buttons (p. 10)
DISC SKIP button (p. 8)
SYNCHRO button (p. 17)
TEXT/TIME display mode-select
button (p. 11)
DIMMER button (p. 12)TAPE button (p. 18)
RANDOM button (p. 13)
SEARCH button (p. 10)
SKIP button (p. 10)
DISC SCAN button (p. 11)
OUTPUT LEVEL button (p. 12)
PAUSE button (p. 9)
PLAY button (p. 8)
STOP button (p. 9)
INDEX button (p. 16)
REPEAT button (p. 16)
Disc play MODE-select button
(p. 8)
TAPE CLEAR
SYNCHRO
PROG
DIMMER
OPEN/
CLOSE
STOP PAUSE PLAY
21 3
INDEX
87 9 0
54 6 +I0
REPEAT RANDOMMODEDISC SCAN
SEARCH
SKIP
OUTPUT LEVEL
+
DISC SKIP
TEXT/
TIME
Parts in the shaded areas are provided for CDC-905 only.
1 Turn the power on.
2 Open the disc tray and load discs.
Use the disc guides to align the discs correctly in the
tray.
3 Close the disc tray.
4 Select a desired disc play mode (1DISC or 5DISCS)
confirming it on the display.
“1DISC” mode: The unit will play a designated disc only.
“5DISCS” mode: The unit will play all discs on the tray in
sequence.
5 Start play from the first track of the disc 1.
* If necessary, select a desired disc by using the DISC SKIP
button or a DISC-select button.
To turn off the power
Press the POWER switch again.
8
1DISC
5DISCS
BASIC OPERATION
POWER
OPEN/
CLOSE
OPEN/
CLOSE
PLAY
PLAY
Shows the selected disc
mode.
Disc tray
This manual describes how to operate this unit by using the remote control transmitter.
To operate this unit on the front panel, use the corresponding buttons on the front panel.
POWER
NATURAL SOUND COMP
2 3 4
DISC
CDC-505
21
TAPE
SYNCHRO
3
INDEX
PROGCLEAR
87 9 0
54 6 +I0
DIMMER
OPEN/
CLOSE
TEXT/
TIME
REPEAT RANDOMMODEDISC SCAN
SEARCH
SKIP
OUTPUT LEVEL
+
STOP PAUSE PLAY
DISC SKIP
2, 3
5
4
5
CDC-905
Label side
upward
(On the front panel)
1
MODE
DISC SKIP
9
English
To stop play temporarily
To resume play, press the PAUSE button again (or press the
PLAY button).
* The (PLAY/PAUSE) button on the front panel can also
be used to stop play temporarily or to resume play.
To stop play completely
STOP
or
5DISCS
1 2 3 4 5
6 7 8 9 10
1112
5DISCS
3 4 5
6 7 8 9 10
1112
PAUSE
or
/
(On the front panel)(On the front panel)
Notes
After closing the disc tray by pressing the OPEN/CLOSE
button or selecting any disc by using the DISC SKIP button
when this unit is stopped, the display shows the total
number of tracks and the total recorded time of the selected
disc for a few seconds.
You can also close the disc tray by pressing the PLAY
( ) button, a DISC-select button on the front panel, a
numeric button or the RANDOM button, or by pressing the
front edge of the disc tray gently. If the tray is closed in
these ways, play will begin automatically, however, the
display will not show the total number of tracks and the total
recorded time of the first selected disc.
PLAYXCHANGE
During play, you can open the disc tray by pressing the
PLAYXCHANGE button on the front panel without interrupting
disc play. However, in this case, pressing the DISC SKIP
button has no effect. You can load or replace discs on the
trays when the disc tray is opening, however, never load a disc
on the tray hidden inside the unit. If doing so, the disc and the
unit may be damaged, because the tray already has a disc,
which is being played.
CD TEXT
This unit is compatible with the CD TEXT function. The CD
TEXT disc has information, such as the disc title, artist names,
and track names. If the current disc is a CD TEXT disc, the unit
reads the disc title, artist name, and track names from the disc.
You can display the CD TEXT data (see “Selecting time
displays and the text data” on page 11).
Display information at disc play
Encloses the tray number of the selected disc.
The numbers corresponding to trays that contain discs light
up after discs are selected.
Shows the selected track number.
Shows the time displays. (Refer to “Selecting time displays
and the text data” on page 11.)
Displays the numbers that correspond to the numbers of
the tracks (as high as number 20) on the selected disc.
After each track is played, its corresponding number
disappears so the number of remaining tracks (and their
numbers) can be seen at a glance.
CDC-905 only
Shows the level of signals output into an amplifier or the
headphones level adjusted by using the OUTPUT LEVEL
buttons.
To play a 8-cm (3-inch) CD
Place it in the inner recessed area of the disc tray. Do not put
a normal (12-cm/5-inch) CD on top of a 8-cm CD.
10
DIRECT PLAY
Select a desired track by using the numeric buttons.
Example: To select track 25
Press
twice, then immediately press
once.
* If a track number higher than the highest track number on
the disc is selected, the last track on the disc will be played.
SKIP PLAY
To play from the beginning of the track following the one now
playing
To play from the beginning of the track now playing
To play from the beginning of the track before the one now
playing
These operations can also be performed when the unit is
paused or stopped.
When using the SKIP button on the remote control
transmitter:
* If the button is pressed and held, the track number is
continuously changed to higher numbers (or lower
numbers).
When using the SKIP/SEARCH buttons on the front panel:
* Be careful not to press and hold a button, otherwise the
selected track is played forward (or backward) rapidly.
+10
To play a desired track on the disc
5
1DISC
5
6 7 8 9 10
1112
SKIP
The selected track number is displayed.
5
To go forward rapidly
To go backward rapidly
The sound can be heard (although slightly garbled) during
manual search in either direction. This is convenient for
locating a precise position within a track, or for reviewing the
contents quickly.
Manual search can also be performed while disc play is
paused. In this case, no sound will be heard.
When using the SKIP/SEARCH buttons on the front panel:
* Be careful not to release the button just after it is
pressed, otherwise the play is skipped to the beginning of
the next track or returned to the beginning of the current
track.
To play forward or backward rapidly (MANUAL SEARCH)
(Press and hold.)
(Press and hold.)
(Twice)
SKIP
SKIP
SEARCH
SEARCH
5DISCS
2 3 4 5
6 7 8 9 10
1112
5DISCS
2 3 4 5
6 7 8 9 10
1112
5DISCS
2 3 4 5
6 7 8 9 10
1112
5DISCS
2 3 4 5
6 7 8 9 10
1112
TEXT/
TIME
11
English
When the DISC SCAN button is pressed in stop mode, this unit
will play a section of each disc in turn for 8 seconds.
If, during this play, you find a disc that you want to listen to,
press the DISC SCAN button once again or press the PLAY
button to cancel this function. The unit will enter into the normal
play mode.
Notes
During this play, the disc tray numbers blink in the display.
Every time the play of a disc is finished, the corresponding
tray number is changed from flashing to lighting.
If the disc being played has a long blank space between
tracks, you will hear no sound during disc scan.
Scanning discs to search for a desired disc (or to check discs on the disc tray)
DISC SCAN
Notes
The remaining time
will not be displayed if the track
number is 21 or higher.
The disc title, artist names, or track names may not be
displayed with some CD TEXT discs. In this case, “(NO
ENTRY)” appears in the display.
Selecting time displays and the text data
You can select any of the four time displays by pressing the TEXT/TIME display mode-select button. When you play a CD with CD
TEXT, the disc title, artist name, and track name are also displayed. Each time you press the TEXT/TIME display mode-select
button, the display changes as follows.
Elapsed time of the track now playing
Remaining time of the track now playing
Total disc play time
Total remaining time on the disc
Disc title
Artist name
Track name
Total remaining time on the disc
:when playing back a disc without CD TEXT
:when playing back a CD TEXT disc
12
CDC-905 only
Adjusting the level of signals output into an
amplifier, etc.
You can adjust the level of sound signals output from the LINE
OUT terminals on the rear panel into an amplifier, etc. as you
prefer by using the OUTPUT LEVEL buttons.
For optimum sound quality
* When the DIGITAL AUDIO OUT (OPTICAL) terminal is used
for the connection, set the level of output signals to max.
* The level of output signals can be checked in the display.
CDC-905 only
When you listen with headphones
Connect the headphones to the PHONES jack and adjust the
volume by using the OUTPUT LEVEL buttons.
* Note that the use of the OUTPUT LEVEL buttons will also
vary the level of the signal output to an amplifier, etc.
OUTPUT LEVEL
+
Changing brightness of the display
OUTPUT LEVEL
+
or
(On the front panel)
If desired, you can change brightness of the display
in three degrees by pressing the DIMMER button.
Normal illumination
Slightly dim
Dim
DIMMER
PHONES
13
English
1 Load one or more discs.
2 Close the disc tray.
3 Select a desired disc play mode (1DISC or 5DISCS).
* If you select “1DISC” mode, next select a desired disc by
using the DISC SKIP button on the remote control
transmitter or a DISC-select button on the front panel.
4
“RNDM” lights up on the display.
To cancel random-sequence play
Press the STOP button or RANDOM button once again, or
open the disc tray by pressing the OPEN/CLOSE button.
“RNDM” disappears from the display.
Notes
This feature will not function during programming, or during
program play.
If the SKIP button is pressed during random-sequence
play, the next randomly programmed track will be played. If
the SKIP button is pressed, play will return to the
beginning of the track now being played.
This indication appears while the unit is
mixing up tracks.
Total remaining time on the disc will not be displayed during
random-sequence play.
RANDOM-SEQUENCE PLAY
You can play the tracks in a random sequence (up to 99 tracks). The unit will automatically mix up tracks from all discs or a
designated disc on the disc tray.
MODE
21
TAPE
SYNCHRO
3
INDEX
PROGCLEAR
87 9 0
54 6 +I0
DIMMER
TEXT/
TIME
OPEN/
CLOSE
REPEAT RANDOMMODEDISC SCAN
SEARCH
SKIP
OUTPUT LEVEL
+
STOP PAUSE PLAY
DISC SKIP
1, 2
4
3
DISC SKIP
21
SYNCHRO
3
INDEX
PROGCLEAR
87 9 0
54 6 +I0
DIMMER
TEXT/
TIME
OPEN/
CLOSE
REPEAT RANDOMMODEDISC SCAN
SEARCH
SKIP
STOP PAUSE PLAY
DISC SKIP
4
1, 2
3
DISC SKIP
RANDOM
OPEN/
CLOSE
CDC-505CDC-905
OPEN/
CLOSE
1 Stop the unit.
2 If you will select tracks from a disc (or discs) other than
the disc on the Disc 1 tray, make this unit display the
total recorded time of each disc to be used by pressing
the DISC SKIP button in turn.
* Without this operation, the total time of the
programmed tracks will not be displayed during
programming.
3 Press the PROG button to begin programming.
4 If necessary, select a desired disc.
5 Program a desired track by pressing the corresponding
numeric button.
6 Repeat steps 4 – 5 to program more tracks. You can
select the same track again.
7 When the programming is completed;
14
PROGRAM PLAY
You can enjoy listening to your favorite tracks selected from one or more discs in any desired order by programming tracks.
PLAY
PROG
PROG
DISC SKIP
or
2 3 4
DISC
5
(On the front panel)
STOP
21
TAPE
SYNCHRO
3
INDEX
PROGCLEAR
87 9 0
54 6 +I0
DIMMER
TEXT/
TIME
OPEN/
CLOSE
REPEAT RANDOMMODEDISC SCAN
SEARCH
SKIP
OUTPUT LEVEL
+
STOP PAUSE PLAY
DISC SKIP
3
2, 4
5
7
1
21
SYNCHRO
3
INDEX
PROGCLEAR
87 9 0
54 6 +I0
DIMMER
TEXT/
TIME
OPEN/
CLOSE
REPEAT RANDOMMODEDISC SCAN
SEARCH
SKIP
STOP PAUSE PLAY
DISC SKIP
5
7
3
2, 4
1
CDC-505CDC-905
DISC SKIP
15
English
To stop program play
Press the STOP button. The first programmed track number
will be displayed.
To resume play, press the PLAY button. Play will begin from
the beginning of the program.
To cancel a programmed sequence
There are several methods, as described below.
Press the STOP button or the CLEAR button while the unit
is stopped.
Open the disc tray.
Switch off the power.
To check program data
1. During program play, press the STOP button.
2. Press the PROG button.
3. Each time the SKIP button is pressed, the track
numbers and sequential order of the programmed tracks
can be checked one after another. The display of the track
number can be returned (sequentially in reverse order) by
pressing the SKIP button.
To correct program data
1. Follow the procedure described in “To check program
data”.
2. Display the track number to be corrected by pressing the
SKIP button.
3. Press a numeric button to select a track to replace the one
displayed. The previously programmed track will be
cleared from the memory and the new one will be
programmed.
4. After the correction has been completed, press the PROG
button or PLAY button once again.
Display information during programming
Shows the program number for the track to be programmed
next.
Shows the selected disc and track number.
Shows the total time of the tracks currently programmed.
Shows only the numbers of programmed tracks on the
selected disc.
* If “STEP 1” does not appear on the display after the PROG
button is pressed, press the TEXT/TIME display mode-select
button.
* If the total time exceeds 99 minutes and 59 seconds, the
time will not be displayed.
Notes
You can program as many as 40 tracks at one time.
You can program a whole disc by pressing “0”, instead of
one track. At that time, “ALL” lights up in the display.
The total time of the programmed tracks will not be
displayed, if a track number higher than 20 is programmed.
If, during programming, the TEXT/TIME display mode-select
button is pressed, the program number display can be
changed to display the total time of the programmed tracks
or no information. To return to the previous display, press
the TEXT/TIME display mode-select button once again.
The SKIP ( and ) button can be used during
playing, but only within the range of the programmed tracks.
Pressing a numeric button stops the current program and
skips to the beginning of the track of the number pressed.
Once that track has finished playing, the previously
interrupted program resumes play.
The SEARCH ( and ) button can be used during
playing to search all tracks, including unprogrammed tracks.
PROG
PROG
6
3 Select the desired index number.
To cancel the index search function
Press the INDEX button.
Notes
Not all discs have index numbers. The index system has a
method for sub-dividing tracks into smaller divisions (for
example, the movements within classical symphonies) for
easier location of those parts. The liner notes with the disc
usually tell if such index numbers are included.
If an index number is selected that is higher than any index
number on that disc, play will start from the last index
number point on the disc.
For some discs, play may begin slightly prior to the actual
designated index point.
If the disc has no encoded index points, play will begin from
the start of the selected track.
16
1 Select a track which has index numbers.
2
SINGLE REPEAT (REP S)
A single track is repeatedly played.
* This is also available in the program play mode and the
random-sequence play mode. (If the repeat play mode is
switched off, the program play mode or the random-
sequence play mode will be resumed.)
FULL REPEAT (REP F)
In the “1DISC” disc play mode: A designated disc is repeatedly
played.
In the “5DISCS” disc play mode: All discs on the disc tray are
repeatedly played.
* In the program play mode, all programmed tracks are
repeatedly played.
* In the random-sequence play mode, all randomly sequenced
tracks are repeatedly played in the same order.
5
6 7 8 9 10
1112
INDEX SEARCH
If the disc includes index numbers, play can be started from any desired index number.
REPEAT PLAY
You can play any desired track or disc (or a set of discs) repeatedly by pressing the REPEAT button. The repeat play mode will
change whenever you press the REPEAT button.
3
REPEAT
INDEX
S
REP
F
REP
(OFF)
5
1 Select a disc.
2 Load a tape on the tape deck.
* CDC-905 only
The peak level searching function of this unit is
useful for adjusting recording level on the tape deck.
(Refer to page 21.)
3
This unit enters into the pause mode, and the tape deck
enters into the REC/PAUSE mode.
* In this mode, the time display on this unit blinks.
4 If desired, select the track to be recorded first.
5
Both CD play and tape deck recording begin.
* CD play begins a little later than recording.
6 If you want to stop recording temporarily and restart
recording from a desired track, follow steps 3–5 again.
To cancel this function
Press the STOP button.
Notes
To finish or stop recording, press the “STOP” button on the
tape deck.
Programmed sequence of tracks can also be recorded with
this function, instead of recording an entire disc. (Refer to
pages 14–15 for the programming procedure.)
CDC-905 only
This function can also be used together with the automatic
tape-programming function. (Refer to pages 18–20.)
17
English
Using a compatible YAMAHA tape deck, you can synchronize the tape deck to start recording automatically when a CD starts
playing. With this function, you can record a CD on tape more easily and precisely. (Refer to the tape deck’s operation manual to
know whether it is compatible or not.)
* This unit and the tape deck must be placed close to each other so that both of them can receive the signals from this unit’s
remote control transmitter at the same time.
PLAY
SYNCHRO
CD SYNCHRONIZED RECORDING
DISC SKIP
6
SKIP
or
21
TAPE
SYNCHRO
3
INDEX
PROGCLEAR
87 9 0
54 6 +I0
DIMMER
OPEN/
CLOSE
TEXT/
TIME
REPEAT RANDOMMODEDISC SCAN
SEARCH
SKIP
OUTPUT LEVEL
+
STOP PAUSE PLAY
DISC SKIP
1
4
5
4
3
21
SYNCHRO
3
INDEX
PROGCLEAR
87 9 0
54 6 +I0
DIMMER
OPEN/
CLOSE
REPEAT RANDOMMODEDISC SCAN
SEARCH
SKIP
STOP PAUSE PLAY
DISC SKIP
4
5
4
1
3
TEXT/
TIME
CDC-505CDC-905
18
1 Stop the unit.
2 Select the disc.
3
The peak level searching function of this unit is useful for
adjusting recording level on the tape deck. (Refer to page 21.)
4
Enter the tape’s total possible recording time (tape length).
You can select any of four tape lengths by pressing the
TAPE button.
You can also enter the tape’s total possible recording
time manually.
Example: For a C-64 tape (32 minutes on each side)
5 Press the REPEAT button.
The unit automatically programs tracks for side A and
side B separately considering the tape’s total time.
* The programmed track numbers and the total number
of tracks for side A and B are displayed for a short
time.
6 Begin recording on the tape deck and press the PLAY
button on this unit’s remote control transmitter at the
same time.
7 The unit will pause at the end of side A of the tape.
Turn the tape over to side B. Resume recording and, at
the same time, press the PLAY or PAUSE button on
this unit’s remote control transmitter.
Notes
It is recommended that you use a tape that is slightly longer
in length than the CD you are recording, because the
programmed tracks on a CD may not fit properly into the
time allowed on each half of the tape.
CD synchronized recording function can be used if your tape
deck is compatible with it. In this case, in step 6 and 7, press
the SYNCHRO button and then press the PLAY button on
this unit’s remote control transmitter. Recording automatically
begins. (For details, refer to page 17.)
Display information during programming
Shows the number of programmed tracks for each side in
turn just after the automatic programming is finished, and
then it is replaced by the number of the first programmed
track for side A.
Shows the total time of programmed tracks for each side.
Shows the programmed track numbers for each side.
PROG
1 2 3 4 5
4
TRACK PROGRAMMING FOR RECORDING TO TAPE
for CDC-655 only
for CDC-905 only
This convenient feature can be used to program tracks for
recording to tape. By only memorizing the tape’s total possible
recording time, the unit will automatically program tracks or
help you to program tracks so they will fit onto the tape with the
least amount of unrecorded space remaining at each end of
the tape.
Automatic tape programming
The unit will automatically program tracks on a disc with the
original order of tracks unchanged.
STOP
6
TAPE
REPEAT
DISC SKIP
(off)
TAPE
21
TAPE
SYNCHRO
3
INDEX
PROGCLEAR
87 9 0
54 6 +I0
DIMMER
OPEN/
CLOSE
TEXT/
TIME
REPEAT RANDOMMODEDISC SCAN
SEARCH
SKIP
OUTPUT LEVEL
+
STOP PAUSE PLAY
DISC SKIP
2
4
6, 7
7
5
1
4
1 Stop the unit.
2 If you will select tracks from a disc (or discs) other than
the disc on the Disc 1 tray, make this unit display the
total recorded time of each disc to be used by pressing
the DISC SKIP button in turn.
* This unit will read the contents of a disc by this
operation. If there is a disc to which this operation is
omitted, tracks on the disc cannot be programmed.
3 Follow step 4 on page 18.
4
5
If necessary, select a desired disc by pressing the DISC
SKIP button.
6 Select a
desired track.
7 Repeat steps 5 and 6 to program more tracks for side A
of the tape. You can select the same track again.
* If “ERROR” appears in the display, the track number just
selected cannot be programmed because there is no
enough time remaining on side A of the tape.
8 When you finish the programming for side A, program
the pause mode by pressing the TAPE button.
* “PAUSE” lights up in the display, and after then you can
begin programming for side B.
9 Repeat steps 5 and 6 to program more tracks for side B
of the tape.
You can select the same track again.
* If “ERROR” appears in the display, the track number just
selected cannot be programmed because there is no
enough time remaining on side B of the tape.
10 The peak level searching function of this unit is
useful for adjusting recording level on the tape deck.
For peak level searching, when the programming for
side B is finished, press the PROG button and then
press the PEAK button on the front panel. (Refer to
page 21.)
11 Start recording on the tape deck and press the PLAY
button on this unit’s remote control transmitter at the
same time.
12 The unit will pause at the end of side A of the tape.
Turn the tape over to side B. Resume recording and,
at the same time, press the PLAY or PAUSE button
on this unit’s remote control transmitter.
Notes
In steps 7 and 9, even if “ERROR” appears in the display,
you can program another track of which time is shorter than
the remaining time on the side of the tape. At this time, if any
other track number lights up in the display, you can program
it.
CD synchronized recording function can be used if your tape
deck is compatible with it.
In this case, in steps 11 and 12, press the SYNCHRO button
and then press the PLAY button on this unit’s remote control
transmitter. Recording automatically begins.
(For details, refer to page 17.)
Notes on tape programming
To check, cancel or correct program data, refer to page 15.
The maximum number of tracks that can be programmed is
40. If, however, the PAUSE mode is inserted, it is counted
as one track.
This function can be used to program up to track number 20.
If the disc has more than 20 tracks, tracks with track number
21 and higher cannot be programmed.
19
English
Manual tape programming
With this function, you can program tracks from one or more
discs in any order to be recorded onto tape.
8
TAPE
PROG
PROG
STOP
21
TAPE
SYNCHRO
3
INDEX
PROGCLEAR
87 9 0
54 6 +I0
DIMMER
OPEN/
CLOSE
TEXT/
TIME
REPEAT RANDOMMODEDISC SCAN
SEARCH
SKIP
OUTPUT LEVEL
+
STOP PAUSE PLAY
DISC SKIP
2, 5
6
11, 12
4, 10
12
1
8
1 Follow steps 1 – 4 on page 18.
2
The unit will automatically program tracks for side A and
side B separately considering the tape’s total time.
* The programmed track numbers and the total number
of tracks for side A and B are displayed for a short
time.
3 Start recording on the tape deck and press the PLAY
button on this unit’s remote control transmitter at the
same time.
4 The unit will pause at the end of side A of the tape.
Turn the tape over to side B. Resume recording and,
at the same time, press the PLAY or PAUSE button on
this unit’s remote control transmitter.
Display information during programming
Shows the side of the tape and the program number for the
track to be programmed next.
Shows the selected disc and track number.
Shows the total remaining time on the side of the tape.
Programmed track numbers light up and programmable
track numbers among the unprogrammed ones blink.
* If “A-1” does not appear in the display after the PROG button
is pressed, press the TEXT/TIME display mode-select
button.
* If, during programming, the TEXT/TIME display mode-select
button is pressed, the program number display can be
changed to display the total remaining time on the side of
the tape. To return to the previous display, press the
TEXT/TIME display mode-select button once again.
20
Random sequential tape programming
The unit will automatically program tracks on a disc in random
sequential order for recording to tape.
Notes
Because the programmed data changes every time the
RANDOM button is pressed, the amount of time remaining
at the end of the tape also changes accordingly.
It is recommended that you use a tape that is slightly longer
in length than the CD you are recording, because the
programmed tracks on a CD may not fit properly into the
time allowed on each half of the tape.
CD synchronized recording function can be used if your tape
deck is compatible with it.
In this case, in steps 3 and 4, press the SYNCHRO button
and then press the PLAY button on this unit’s remote control
transmitter. Recording automatically begins.
(For details, refer to page 17.)
Display information during programming
Shows the number of programmed tracks for each side in
turn just after the automatic programming is finished, and
then it is replaced by the number of the first programmed
track for side A.
Shows the total time of programmed tracks for each side.
Shows the programmed track numbers for each side.
PROG
1 3 5
7
RANDOM
PROG
1 2 3 4 5
6 7 8 9 10
PROG
1 2 3 4 5
6 7 8 9 10
21
TAPE
SYNCHRO
3
INDEX
PROGCLEAR
87 9 0
54 6 +I0
DIMMER
OPEN/
CLOSE
TEXT/
TIME
REPEAT RANDOMMODEDISC SCAN
SEARCH
SKIP
OUTPUT LEVEL
+
STOP PAUSE PLAY
DISC SKIP
2
3, 4
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Yamaha CDC-905 Bruksanvisning

Kategori
CD-spelare
Typ
Bruksanvisning