Not for
Reproduction
80006746WST
Copyright © Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
BRIGGS & STRATTON is a registered
trademark of Briggs & Stratton Corporation.
Revision: B
Not for
Reproduction
1
2
3
4
5
6
7
8
2 BRIGGSandSTRATTON.com
Not for
Reproduction
9
10
11
12
3
Not for
Reproduction
Copyright © Briggs & Stratton Corporation, Milwaukee, WI, USA. All rights reserved.
This manual contains safety information to make you aware of the hazards and risks
associated with engines and how to avoid them. It also contains instructions for the proper
use and care of the engine. Because Briggs & Stratton Corporation does not necessarily
know what equipment this engine will power, it is important that you read and understand
these instructions and the instructions for the equipment. Save these original instructions
for future reference.
Note:
The figures and illustrations in this manual are provided for reference only and may
differ from your specific model. Contact your dealer if you have questions.
For replacement parts or technical assistance, record below the engine model, type, and
code numbers along with the date of purchase. These numbers are located on your engine
(see the
Features and Controls
section).
Date of Purchase
Engine Model - Type - Trim
Engine Serial Number
Look for the 2D barcode located on some
engines. When viewed with a 2D-capable
device, the code will bring up our website
where you can access support information
for this product. Data rates apply. Some
countries may not have online support
information available.
Recycling Information
All packaging, used oil, and batteries should be recycled
according to applicable government regulations.
Operator Safety
Safety Alert Symbol and Signal Words
The safety alert symbol is used to identify safety information about hazards that can
result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used with
the alert symbol to indicate the likelihood and the potential severity of injury. In addition, a
hazard symbol may be used to represent the type of hazard.
DANGER indicates a hazard which, if not avoided, will result in death or serious
injury.
WARNING indicates a hazard which, if not avoided, could result in death or serious
injury.
CAUTION indicates a hazard which, if not avoided, could result in minor or
moderate injury.
NOTICE
indicates an situation that could result in damage to the product.
Hazard Symbols and Meanings
MeaningSymbolMeaningSymbol
Read and understand the
Operator's Manual before
operating or servicing the unit.
Safety information about
hazards that can result in
personal injury.
Explosion hazardFire hazard
MeaningSymbolMeaningSymbol
Toxic fume hazardShock hazard
Noise hazard - Ear protection
recommended for extended
use.
Hot surface hazard
Explosion hazardThrown object hazard -
Wear eye protection.
Kickback hazardFrostbite hazard
Chemical HazardAmputation hazard - moving
parts
CorrosiveThermal heat hazard
Safety Messages
WARNING
Certain components in this product and its related accessories contain chemicals
known to the State of California to cause cancer, birth defects, or other reproductive
harm. Wash hands after handling.
WARNING
The engine exhaust from this product contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.
WARNING
Briggs & Stratton Engines are not designed for and are not to be used to power: fun-
karts; go-karts; children's, recreational, or sport all-terrain vehicles (ATVs); motorbikes;
hovercraft; aircraft products; or vehicles used in competitive events not sanctioned by
Briggs & Stratton. For information about competitive racing products, see
www.briggsracing.com. For use with utility and side-by-side ATVs, please contact
Briggs & Stratton Engine Application Center, 1-866-927-3349. Improper engine
application may result in serious injury or death.
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Adding Fuel
Turn engine off and let engine cool at least 2 minutes before removing the fuel cap.
Fill fuel tank outdoors or in well-ventilated area.
Do not overfill fuel tank. To allow for expansion of the fuel, do not fill above the
bottom of the fuel tank neck.
Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if
necessary.
If fuel spills, wait until it evaporates before starting engine.
When Starting Engine
4 BRIGGSandSTRATTON.com
Not for
Reproduction
Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in place
and secured.
Do not crank engine with spark plug removed.
If engine floods, set choke (if equipped) to OPEN / RUN position, move throttle (if
equipped) to FAST position and crank until engine starts.
When Operating Equipment
Do not tip engine or equipment at angle which causes fuel to spill.
Do not choke the carburetor to stop engine.
Never start or run the engine with the air cleaner assembly (if equipped) or the air
filter (if equipped) removed.
When Changing Oil
If you drain the oil from the top oil fill tube, the fuel tank must be empty or fuel can
leak out and result in a fire or explosion.
When Tipping Unit for Maintenance
When performing maintenance that requires the unit to be tipped, the fuel tank, if
mounted on the engine, must be empty or fuel can leak out and result in a fire or
explosion.
When Transporting Equipment
Transport with fuel tank EMPTY or with fuel shut-off valve in the CLOSED position.
When Storing Fuel Or Equipment With Fuel In Tank
Store away from furnaces, stoves, water heaters or other appliances that have pilot
lights or other ignition sources because they can ignite fuel vapors.
WARNING
Starting engine creates sparking.
Sparking can ignite nearby flammable gases.
Explosion and fire could result.
If there is natural or LP gas leakage in area, do not start engine.
Do not use pressurized starting fluids because vapors are flammable.
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. You CANNOT see it, smell it, or
taste it. Even if you do not smell exhaust fumes, you could still be exposed to
carbon monoxide gas. If you start to feel sick, dizzy, or weak while using this
product, get to fresh air RIGHT AWAY. See a doctor. You may have carbon
monoxide poisoning.
Operate this product ONLY outside far away from windows, doors and vents to
reduce the risk of carbon monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
Install battery-operated carbon monoxide alarms or plug-in carbon monoxide alarms
with battery back-up according to the manufacturer's instructions. Smoke alarms
cannot detect carbon monoxide gas.
DO NOT run this product inside homes, garages, basements, crawlspaces, sheds,
or other partially-enclosed spaces even if using fans or opening doors and windows
for ventilation. Carbon monoxide can quickly build up in these spaces and can linger
for hours, even after this product has shut off.
ALWAYS place this product downwind and point the engine exhaust away from
occupied spaces.
WARNING
Rapid retraction of starter cord (kickback) will pull hand and arm toward engine
faster than you can let go.
Broken bones, fractures, bruises or sprains could result.
When starting engine, pull the starter cord slowly until resistance is felt and then
pull rapidly to avoid kickback.
Remove all external equipment / engine loads before starting engine.
Direct-coupled equipment components such as, but not limited to, blades, impellers,
pulleys, sprockets, etc., must be securely attached.
WARNING
Rotating parts can contact or entangle hands, feet, hair, clothing, or accessories.
Traumatic amputation or severe laceration can result.
Operate equipment with guards in place.
Keep hands and feet away from rotating parts.
Tie up long hair and remove jewelry.
Do not wear loose-fitting clothing, dangling drawstrings or items that could become
caught.
WARNING
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
Allow muffler, engine cylinder and fins to cool before touching.
Remove accumulated debris from muffler area and cylinder area.
It is a violation of California Public Resource Code, Section 4442, to use or operate
the engine on any forest-covered, brush-covered, or grass-covered land unless the
exhaust system is equipped with a spark arrester, as defined in Section 4442,
maintained in effective working order. Other states or federal jurisdictions may have
similar laws. Contact the original equipment manufacturer, retailer, or dealer to
obtain a spark arrester designed for the exhaust system installed on this engine.
WARNING
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic amputation, or
laceration.
Fire hazard
Before performing adjustments or repairs:
Disconnect the spark plug wire and keep it away from the spark plug.
Disconnect battery at negative terminal (only engines with electric start.)
Use only correct tools.
Do not tamper with governor spring, links or other parts to increase engine speed.
Replacement parts must be of the same design and installed in the same position
as the original parts. Other parts may not perform as well, may damage the unit,
and may result in injury.
Do not strike the flywheel with a hammer or hard object because the flywheel may
later shatter during operation.
When testing for spark:
Use approved spark plug tester.
Do not check for spark with spark plug removed.
Features and Controls
Engine Controls
Compare the illustration (Figure: 1, 2) with your engine to familiarize yourself with the
location of various features and controls.
A. Engine Identification Numbers Model - Type - Code
B. Spark Plug
C. Choke
D. Primer
E. Fuel Shut-off
F. Starter Cord Handle
G. Air Intake Grille
H. Fuel Tank and Cap
5
Not for
Reproduction
I. Dipstick/Oil Fill
J. Oil Drain Plug
K. Muffler, Muffler Guard (if equipped), Spark Arrester (if equipped)
L. Safety Key (if equipped)
1
M. Push Button Electric Start
N. Power Cord Receptacle - 120 Volt
O. Power Cord Receptacle - 230 Volt
P. Electric Starter
Q. Throttle Control (if equipped)
1
R. Key (if equipped)
1
1
Some engines and equipment have remote controls. See the equipment manual
for location and operation of remote controls.
Engine Control Symbols and Meanings
MeaningSymbolMeaningSymbol
Engine speed - SLOWEngine speed - FAST
ON - OFFEngine speed - STOP
Engine start - Choke OPENEngine start - Choke
CLOSED
Fuel Shut-off - CLOSEDFuel Cap
Fuel Shut-off - OPEN
Fuel level - Maximum
Do not overfill
Operation
Oil Recommendations
Oil Capacity: See the
Specifications
section.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers
or dealers may have added oil to the engine. Before you start the engine for the first
time, make sure to check the oil level and add oil according to the instructions in this
manual. If you start the engine without oil, it will be damaged beyond repair and will not
be covered under warranty.
We recommend the use of Briggs & Stratton Warranty Certified oils for best performance.
Other high-quality detergent oils are acceptable if classified for service SF, SG, SH, SJ or
higher. Do not use special additives.
Outdoor temperatures determine the proper oil viscosity for the engine. Use the chart to
select the best viscosity for the outdoor temperature range expected. Engines on most
outdoor power equipment operate well with 5W-30 Synthetic oil. For equipment operated
in hot temperatures, Vanguard™ 15W-50 Synthetic oil provides the best protection.
SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard starting.A
10W-30 - Above 80 °F (27 °C) the use of 10W-30 may cause increased oil
consumption. Check oil level more frequently.
B
5W-30C
Synthetic 5W-30D
Vanguard™ Synthetic 15W-50E
Check Oil Level
See Figure: 3, 4
Before adding or checking the oil
Make sure the engine is level.
Clean the oil fill area of any debris.
Short Dipstick, if equipped
1. Remove the dipstick (A, Figure 3) and wipe with a clean cloth.
2. Install the dipstick (A, Figure 3). Do not turn or tighten.
3. Remove the dipstick and check the oil level. Correct oil level is at the top of the full
indicator (B, Figure 3) on the dipstick.
4. If oil level is low, slowly add oil into the engine oil fill (C, Figure 3). Fill to point of
overflowing.
5. Reinstall and tighten the dipstick (A, Figure 3).
Extended Dipstick, if equipped
1. Remove the dipstick (A, Figure 4) and wipe with a clean cloth.
2. Install and tighten the dipstick (A, Figure 4).
3. Remove the dipstick and check the oil level. Correct oil level is at the top of the full
indicator (B, Figure 4) on the dipstick.
4. If oil level is low, slowly add oil into the engine oil fill (C, Figure 4). Do not overfill.
After adding oil, wait one minute and then recheck the oil level.
5. Reinstall and tighten the dipstick (A, Figure 4).
Low Oil Protection System (if equipped)
Some engines are equipped with a low oil sensor. If the oil is low, the sensor will either
activate a warning light or stop the engine. Stop the engine and follow these steps before
restarting the engine.
Make sure the engine is level.
Check the oil level. See the
Check Oil Level
section.
If the oil level is low, add the proper amount of oil. Start the engine and make sure
the warning light (if equipped) is not activated.
If the oil level is not low, do not start the engine. Contact a Briggs & Stratton
Authorized Service Dealer to have the oil problem corrected.
Fuel Recommendations
Fuel must meet these requirements:
Clean, fresh, unleaded gasoline.
A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.
Gasoline with up to 10% ethanol (gasohol) is acceptable.
6 BRIGGSandSTRATTON.com
Not for
Reproduction
NOTICE
Do not use unapproved gasolines, such as E15 and E85. Do not mix oil in
gasoline or modify the engine to run on alternate fuels. Use of unapproved fuels will
damage the engine components, which will not be covered under warranty.
To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel. See
Storage.
All fuel is not the same. If starting or performance problems occur, change fuel
providers or change brands. This engine is certified to operate on gasoline. The emissions
control system for this engine is EM (Engine Modifications).
High Altitude
At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON) gasoline
is acceptable.
For carbureted engines, high altitude adjustment is required to maintain performance.
Operation without this adjustment will cause decreased performance, increased fuel
consumption, and increased emissions. Contact a Briggs & Stratton Authorized Service
Dealer for high altitude adjustment information. Operation of the engine at altitudes below
2,500 feet (762 meters) with the high altitude adjustment is not recommended.
For Electronic Fuel Injection (EFI) engines, no high altitude adjustment is necessary.
Add Fuel
See Figure: 5
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When adding fuel
Turn engine off and let engine cool at least 2 minutes before removing the fuel cap.
Fill fuel tank outdoors or in well-ventilated area.
Do not overfill fuel tank. To allow for expansion of the fuel, do not fill above the bottom
of the fuel tank neck.
Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.
Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if
necessary.
If fuel spills, wait until it evaporates before starting engine.
1. Clean the fuel cap area of dirt and debris. Remove the fuel cap.
2. Fill the fuel tank (A, Figure 5) with fuel. To allow for expansion of the fuel, do not fill
above the bottom of the fuel tank neck (B).
3. Reinstall the fuel cap.
Start and Stop Engine
See Figure: 6, 7
Start Engine
WARNING
Rapid retraction of starter cord (kickback) will pull hand and arm toward engine
faster than you can let go.
Broken bones, fractures, bruises or sprains could result.
When starting engine, pull the starter cord slowly until resistance is felt and then pull
rapidly to avoid kickback.
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Starting Engine
Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in place
and secured.
Do not crank engine with spark plug removed.
If engine floods, set choke (if equipped) to OPEN / RUN position, move throttle (if
equipped) to FAST position and crank until engine starts.
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. You CANNOT see it, smell it, or taste
it. Even if you do not smell exhaust fumes, you could still be exposed to carbon
monoxide gas. If you start to feel sick, dizzy, or weak while using this product,
shut it off and get to fresh air RIGHT AWAY. See a doctor. You may have carbon
monoxide poisoning.
Operate this product ONLY outside far away from windows, doors and vents to reduce
the risk of carbon monoxide gas from accumulating and potentially being drawn
towards occupied spaces.
Install battery-operated carbon monoxide alarms or plug-in carbon monoxide alarms
with battery back-up according to the manufacturer's instructions. Smoke alarms
cannot detect carbon monoxide gas.
DO NOT run this product inside homes, garages, basements, crawlspaces, sheds,
or other partially-enclosed spaces even if using fans or opening doors and windows
for ventilation. Carbon monoxide can quickly build up in these spaces and can linger
for hours, even after this product has shut off.
ALWAYS place this product downwind and point the engine exhaust away from
occupied spaces.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Before you start
the engine, make sure you add oil according to the instructions in this manual. If you
start the engine without oil, it will be damaged beyond repair and will not be covered
under warranty.
Note:
Equipment may have remote controls. See the equipment manual for location and
operation of remote controls.
1. Check the engine oil. See the
Check Oil Level
section.
2. Make sure equipment drive controls, if equipped, are disengaged.
3. Move the throttle control (A, Figure 6), if equipped, to the fast position. Operate the
engine in the fast position.
4. Move the fuel shut-off (B, Figure 6), if equipped, to the open position.
5. Key, if equipped: Insert the key (C, Figure 6), and turn to the on position
Safety Key, if equipped: Push in the safety key (D).
6. Move the choke control (E, Figure 6) to the choke position.
Note:
Choke is usually unnecessary when restarting a warm engine.
7. Push the primer (F, Figure 6) two (2) times.
Note:
Priming is usually unnecessary when restarting a warm engine.
8. Rewind Start, if equipped: Firmly hold the starter cord handle (G, Figure 7). Pull
the starter cord handle slowly until resistance is felt, then pull rapidly.
WARNING
Rapid retraction of the starter cord (kickback) will pull your hand and arm toward the
engine faster than you can let go. Broken bones, fractures, bruises or sprains could
result. When starting engine, pull the starter cord slowly until resistance is felt and then
pull rapidly to avoid kickback.
9. Electric Start, if equipped: Connect the extension cord to the power cord receptacle
(H, 120 Volt) or (J, 230 Volt) and then into a wall receptacle (Figure 7). Depress the
push button (K). After you start the engine, disconnect the extension cord from the
wall receptacle and then from the power cord receptacle (H, J).
Note:
If an additional extension cord is required, make sure to use a 3-wire grounded
extension cord.
WARNING
If the extension cord is damaged, it must be replaced by the manufacturer or its service
agent or a simularly qualified person in order to avoid a hazard.
NOTICE
To extend the life of the starter, use short starting cycles (five seconds
maximum). Wait one minute between starting cycles.
10. As the engine warms up, move the choke control (E, Figure 6) to the run position.
Note:
If the engine does not start after repeated attempts, contact your local dealer or go
to BRIGGSandSTRATTON.com or call 1-800-233-3723 (in USA).
7
Not for
Reproduction
Stop Engine
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
Do not choke the carburetor to stop the engine.
1. Key, if equipped: Turn the key (C, Figure 6) to the off position. Remove the key and
keep in a safe place out of the reach of children.
Safety Key, if equipped: Remove the safety key (D) and keep in a safe place out
of the reach of children.
2. After the engine stops, move the fuel shut-off (B, Figure 6), if equipped, to the closed
position.
Maintenance
NOTICE
If the engine is tipped during maintenance, the fuel tank, if mounted on
engine, must be empty and the spark plug side must be up. If the fuel tank is not empty
and if the engine is tipped in any other direction, it may be difficult to start due to oil or
gasoline contaminating the air filter and/or the spark plug.
WARNING
When performing maintenance that requires the unit to be tipped, the fuel tank, if mounted
on the engine, must be empty or fuel can leak out and result in a fire or explosion.
We recommend that you see any Briggs & Stratton Authorized Service Dealer for all
maintenance and service of the engine and engine parts.
NOTICE
All the components used to build this engine must remain in place for proper
operation.
WARNING
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic amputation, or
laceration.
Fire hazard
Before performing adjustments or repairs:
Disconnect the spark plug wire and keep it away from the spark plug.
Disconnect battery at negative terminal (only engines with electric start.)
Use only correct tools.
Do not tamper with governor spring, links or other parts to increase engine speed.
Replacement parts must be of the same design and installed in the same position
as the original parts. Other parts may not perform as well, may damage the unit, and
may result in injury.
Do not strike the flywheel with a hammer or hard object because the flywheel may
later shatter during operation.
When testing for spark:
Use approved spark plug tester.
Do not check for spark with spark plug removed.
Emissions Control Service
Maintenance, replacement, or repair of the emissions control devices and systems
may be performed by any off-road engine repair establishment or individual. However,
to obtain "no charge" emissions control service, the work must be performed by a factory
authorized dealer. See the Emissions Control Statements.
Maintenance Schedule
First 5 Hours
Change oil
Every 8 Hours or Daily
Check engine oil level
Every 50 Hours or Annually
Change engine oil
Check muffler and muffler guard
Annually
Replace spark plug
Check valve clearance.
1
1
Not required unless engine performance problems are noted.
Carburetor and Engine Speed
Never make adjustments to the carburetor or engine speed. The carburetor was set at the
factory to operate efficiently under most conditions. Do not tamper with the governor spring,
linkages, or other parts to change the engine speed. If any adjustments are required contact
a Briggs & Stratton Authorized Service Dealer for service.
NOTICE
The equipment manufacturer specifies the maximum speed for the engine
as installed on the equipment. Do not exceed this speed. If you are unsure what the
equipment maximum speed is, or what the engine speed is set to from the factory,
contact a Briggs & Stratton Authorized Service Dealer for assistance. For safe and
proper operation of the equipment, the engine speed should be adjusted only by a
qualified service technician.
Service Spark Plug
See Figure: 8
Check the gap (A, Figure 8) with a wire gauge (B). If necessary, reset the gap. Install and
tighten the spark plug to the recommended torque. For gap setting or torque, see the
Specifications
section.
Note:
In some areas, local law requires using a resistor spark plug to suppress ignition
signals. If this engine was originally equipped with a resistor spark plug, use the same type
for replacement.
Service Exhaust System
WARNING
Running engines produce heat. Engine parts, especially muffler, become extremely
hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
Allow muffler, engine cylinder and fins to cool before touching.
Remove accumulated debris from muffler area and cylinder area.
It is a violation of California Public Resource Code, Section 4442, to use or operate
the engine on any forest-covered, brush-covered, or grass-covered land unless the
exhaust system is equipped with a spark arrester, as defined in Section 4442,
maintained in effective working order. Other states or federal jurisdictions may have
similar laws. Contact the original equipment manufacturer, retailer, or dealer to obtain
a spark arrester designed for the exhaust system installed on this engine.
Remove accumulated debris from muffler and cylinder area. Inspect the muffler for cracks,
corrosion, or other damage. Remove the deflector or the spark arrester, if equipped, and
inspect for damage or carbon blockage. If damage is found, install replacement parts before
operating.
WARNING
Replacement parts must be of the same design and installed in the same position as
the original parts. Other parts may not perform as well, may damage the unit, and may
result in injury.
Change Engine Oil
See Figure: 9, 10, 11
Used oil is a hazardous waste product and must be disposed of properly. Do not discard
with household waste. Check with your local authorities, service center, or dealer for safe
disposal/recycling facilities.
8 BRIGGSandSTRATTON.com
Not for
Reproduction
Remove Oil
1. With engine off but still warm, disconnect the spark plug wire (D, Figure 9) and keep
it away from the spark plug (E).
2. Remove the oil drain plug (F, Figure 10). Drain the oil into an approved container.
Note:
Any of the oil drain plugs (G, Figure 10) may be installed in the engine.
3. After the oil has drained, install and tighten the oil drain plug (F, Figure 10).
Add Oil
Make sure the engine is level.
Clean the oil fill area of any debris.
See the
Specifications
section for oil capacity.
Short Dipstick, if equipped
1. Remove the dipstick (A, Figure 10) and wipe with a clean cloth.
2. Slowly pour oil into the engine oil fill (C, Figure 10). Fill to point of overflowing.
3. Install the dipstick (A, Figure 10). Do not turn or tighten. Remove and check the
oil level. Correct oil level is at the top of the full indicator (B) on the dipstick.
4. Reinstall and tighten the dipstick (A, Figure 10).
5. Connect the spark plug wire (D, Figure 9) to the spark plug (E).
Extended Dipstick, if equipped
1. Remove the dipstick (A, Figure 11) and wipe with a clean cloth.
2. Slowly pour oil into the engine oil fill (C, Figure 11). Do not overfill. After adding oil,
wait one (1) minute and then recheck the oil level.
3. Install and tighten the dipstick (A, Figure 11).
4. Remove and check the oil level. Correct oil level is at the top of the full indicator (B,
Figure 11) on the dipstick.
5. Reinstall and tighten the dipstick (A, Figure 11).
6. Connect the spark plug wire (D, Figure 9) to the spark plug (E).
Air Filter
The engine is not equipped with an air filter. DO NOT use this engine for anything other
than snow removal.
Storage
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Storing Fuel Or Equipment With Fuel In Tank
Store away from furnaces, stoves, water heaters or other appliances that have pilot
lights or other ignition sources because they can ignite fuel vapors.
Fuel System
See Figure: 12
Store the engine level (normal operating position). Fill fuel tank (A, Figure 12) with fuel.
To allow for expansion of fuel, do not overfill above the fuel tank neck (B).
Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum deposits
to form in the fuel system or on essential carburetor parts. To keep fuel fresh, use Briggs
& Stratton Advanced Formula Fuel Treatment & Stabilizer, available wherever Briggs
& Stratton genuine service parts are sold.
There is no need to drain gasoline from the engine if a fuel stabilizer is added according
to instructions. Run the engine for two (2) minutes to circulate the stabilizer throughout the
fuel system before storage.
If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained into
an approved container. Run the engine until it stops from lack of fuel. The use of a fuel
stabilizer in the storage container is recommended to maintain freshness.
Engine Oil
While the engine is still warm, change the engine oil. See the
Change Engine Oil
section.
Troubleshooting
For assistance, contact your local dealer or go to BRIGGSandSTRATTON.com or call
1-800-233-3723 (in USA).
Specifications
Model: 100000
9.95 ci (163 cc)Displacement
2.677 in (68,00 mm)Bore
1.77 in (45,00 mm)Stroke
18 - 20 oz (,54 - ,59 L)Oil Capacity
.030 in (,76 mm)Spark Plug Gap
180 lb-in (20 Nm)Spark Plug Torque
.010 - .014 in (,25 - ,36 mm)Armature Air Gap
.004 - .006 in (,10 - ,15 mm)Intake Valve Clearance
.006 - .008 in (,15 - ,20 mm)Exhaust Valve Clearance
Model: 130000
12.69 ci (208 cc)Displacement
2.757 in (70,02 mm)Bore
2.126 in (54,00 mm)Stroke
18 - 20 oz (,54 - ,59 L)Oil Capacity
.030 in (,76 mm)Spark Plug Gap
180 lb-in (20 Nm)Spark Plug Torque
.010 - .014 in (,25 - ,36 mm)Armature Air Gap
.004 - .006 in (,10 - ,15 mm)Intake Valve Clearance
.006 - .008 in (,15 - ,20 mm)Exhaust Valve Clearance
Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and
1% for each 10° F (5.6° C) above 77° F (25° C). The engine will operate satisfactorily at
an angle up to 15°. Refer to the equipment operator's manual for safe allowable operating
limits on slopes.
Service Parts - Model: 100000, 130000
Part NumberService Part
100117, 100120Advanced Formula Fuel Treatment &
Stabilizer
491055Resistor Spark Plug
696202, 5066Long Life Platinum Spark Plug
89838, 5023Spark Plug Wrench
19368Spark Tester
We recommend that you see any Briggs & Stratton Authorized Dealer for all maintenance
and service of the engine and engine parts.
Power Ratings: The gross power rating for individual gasoline engine models is labeled
in accordance with SAE (Society of Automotive Engineers) code J1940 Small Engine
Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque
values are derived at 2600 RPM for those engines with “rpm” called out on the label and
3060 RPM for all others; horsepower values are derived at 3600 RPM. The gross power
curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken
with exhaust and air cleaner installed whereas gross power values are collected without
these attachments. Actual gross engine power will be higher than net engine power and
is affected by, among other things, ambient operating conditions and engine-to-engine
variability. Given the wide array of products on which engines are placed, the gasoline
engine may not develop the rated gross power when used in a given piece of power
equipment. This difference is due to a variety of factors including, but not limited to, the
variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel
pump, etc.), application limitations, ambient operating conditions (temperature, humidity,
altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations,
Briggs & Stratton may substitute an engine of higher rated power for this engine.
9
Not for
Reproduction
Warranty
Briggs & Stratton Engine Warranty
Effective January 2017
Limited Warranty
Briggs & Stratton warrants that, during the warranty period specified below, it will repair or
replace, free of charge, any part that is defective in material or workmanship or both.
Transportation charges on product submitted for repair or replacement under this warranty
must be borne by purchaser. This warranty is effective for and is subject to the time periods
and conditions stated below. For warranty service, find the nearest Authorized Service
Dealer in our dealer locator map at BRIGGSandSTRATTON.COM. The purchaser must
contact the Authorized Service Dealer, and then make the product available to the
Authorized Service Dealer for inspection and testing.
There is no other express warranty. Implied warranties, including those of
merchantability and fitness for a particular purpose, are limited to the warranty
period listed below, or to the extent permitted by law. Liability for incidental or
consequential damages are excluded to the extent exclusion is permitted by law. Some
states or countries do not allow limitations on how long an implied warranty lasts, and
some states or countries do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation and exclusion may not apply to you. This
warranty gives you specific legal rights and you may also have other rights which vary
from state to state and country to country
4
.
Standard Warranty Terms
1, 2, 3
Commercial
Use
Consumer
Use
Brand / Product Name
36 months36 monthsVanguard™; Commercial Series
12 months24 monthsEngines Featuring Dura-Bore™ Cast Iron Sleeve
3 months24 monthsAll Other Engines
1
These are our standard warranty terms, but occasionally there may be additional
warranty coverage that was not determined at time of publication. For a listing of
current warranty terms for your engine, go to BRIGGSandSTRATTON.com or contact
your Briggs & Stratton Authorized Service Dealer.
2
There is no warranty for engines on equipment used for prime power in place of a
utility or for standby generators used for commercial purposes. Engines used in
competitive racing or on commercial or rental tracks are not warrantied.
3
Vanguard installed on standby generators: 24 months consumer use, no warranty
commercial use. Vanguard installed on utility vehicles: 24 months consumer use, 24
months commercial use. Commercial Series with manufacturing date before July
2017, 24 months consumer use, 24 months commercial use.
4
In Australia - Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure. For warranty
service, find the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing
to [email protected], Briggs & Stratton Australia Pty Ltd, 1
Moorebank Avenue, Moorebank, NSW , Australia, 2170.
The warranty period begins on the original date of purchase by the first retail or commercial
consumer. "Consumer use" means personal residential household use by a retail consumer.
"Commercial use" means all other uses, including use for commercial, income producing
or rental purposes. Once an engine has experienced commercial use, it shall thereafter
be considered as a commercial use engine for purposes of this warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial purchase
date at the time warranty service is requested, the manufacturing date of the product
will be used to determine the warranty period. Product registration is not required
to obtain warranty service on Briggs & Stratton products.
About Your Warranty
This limited warranty covers engine-related material and/or workmanship issues only, and
not replacement or refund of the equipment to which the engine may be mounted. Routine
maintenance, tune-ups, adjustments, or normal wear and tear are not covered under this
warranty. Similarly, warranty is not applicable if the engine has been altered or modified
or if the engine serial number has been defaced or removed. This warranty does not cover
engine damage or performance problems caused by:
1. The use of parts that are not original Briggs & Stratton parts;
2. Operating the engine with insufficient, contaminated, or an incorrect grade of
lubricating oil;
3. The use of contaminated or stale fuel, gasoline formulated with ethanol greater than
10%, or the use of alternative fuels such as liquefied petroleum or natural gas on
engines not originally designed/manufactured by Briggs & Stratton to operate on
such fuels;
4. Dirt which entered the engine because of improper air cleaner maintenance or re-
assembly;
5. Striking an object with the cutter blade of a rotary lawn mower, loose or improperly
installed blade adapters, impellers, or other crankshaft coupled devices, or excessive
v-belt tightness;
6. Associated parts or assemblies such as clutches, transmissions, equipment controls,
etc., which are not supplied by Briggs & Stratton;
7. Overheating due to grass clippings, dirt and debris, or rodent nests which plug or
clog the cooling fins or flywheel area, or by operating the engine without sufficient
ventilation;
8. Excessive vibration due to over-speeding, loose engine mounting, loose or unbalanced
cutter blades or impellers, or improper coupling of equipment components to the
crankshaft;
9. Misuse, lack of routine maintenance, shipping, handling, or warehousing of equipment,
or improper engine installation.
Warranty service is available only through Briggs & Stratton Authorized Service
Dealers. Locate your nearest Authorized Service Dealer in our dealer locator map
at BRIGGSandSTRATTON.COM or by calling 1-800-233-3723 (in USA).
80004537 (Rev. C)
Briggs & Stratton Emissions Warranty
California, U.S. EPA, and Briggs & Stratton Corporation Emissions
Control Warranty Statement - Your Warranty Rights and
Obligations
For Briggs & Stratton Engine Models with "F" Trim Designation (Model-Type-Trim
Representation xxxxxx xxxx Fx)
The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are pleased
to explain the emissions control system warranty on your Model Year 2017-2019
engine/equipment. In California, new small off-road engines and large spark ignited engines
less than or equal to 1.0 liter must be designed, built, and equipped to meet the State's
stringent anti-smog standards. B&S must warrant the emissions control system on your
engine/equipment for the periods of time listed below provided there has been no abuse,
neglect, or improper maintenance of your engine/equipment.
Your exhaust emissions control system may include parts such as the carburetor or fuel
injection system, ignition system, and catalytic converter. Also included may be hoses,
belts, connectors, sensors, and other emissions-related assemblies. Your evaporative
emission control system may include parts such as: carburetors, fuel tanks, fuel lines, fuel
caps, valves, canisters, filters, vapor hoses, clamps, connectors, and other associated
components.
Where a warrantable condition exists, B&S will repair your engine/equipment at no cost
to you including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
Small off-road engines and large spark ignited engines less than or equal to 1.0 liter, and
any related emissions components of the equipment, are warranted for two years, or for
the time period listed in the respective engine or product warranty statement, whichever
is greater. If any emissions-related part on your B&S engine/equipment is defective, the
part will be repaired or replaced by B&S.
Owner’s Warranty Responsibilities:
As the engine/equipment owner, you are responsible for the performance of the
required maintenance listed in your Operator's Manual. B&S recommends that you
retain all receipts covering maintenance on your engine/equipment, but B&S cannot
deny warranty solely for the lack of receipts or your failure to ensure the performance
of all scheduled maintenance.
As the engine/equipment owner, you should however be aware that B&S may deny
you warranty coverage if your engine/equipment or a part has failed due to abuse,
neglect, improper maintenance, or unapproved modifications.
You are responsible for presenting your engine/equipment to a B&S distribution
center, servicing dealer, or other equivalent entity, as applicable, as soon as a problem
exists. The warranty repairs should be completed in a reasonable amount of time,
not to exceed 30 days. If you have any questions regarding your warranty rights and
responsibilities, you should contact B&S at 1-800-444-7774 (in USA) or
BRIGGSandSTRATTON.COM.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty Coverage.
It is in addition to the B&S engine warranty for non-regulated engines found in the Operator's
Manual.
1. Warranted Emissions Parts
10 BRIGGSandSTRATTON.com
Not for
Reproduction
Coverage under this warranty extends only to the parts listed below (the emissions
control systems parts) to the extent these parts were present on the B&S engine
and/or B&S supplied fuel system.
a. Fuel Metering System
Cold start enrichment system (soft choke)
Carburetor or fuel injection system
Oxygen sensor
Electronic control unit
Fuel pump module
Fuel line, fuel line fittings, clamps
Fuel tank, cap and tether
Carbon canister
b. Air Induction System
Air cleaner
Intake manifold
Purge and vent line
c. Ignition System
Spark plug(s)
Magneto ignition system
d. Catalyst System
Catalytic converter
Exhaust manifold
Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
Vacuum, temperature, position, time sensitive valves and switches
Connectors and assemblies
2. Length of Coverage
Coverage is for a period of two years from date of original purchase, or for the time
period listed in the respective engine or product warranty statement, whichever is
greater. B&S warrants to the original purchaser and each subsequent purchaser that
the engine is designed, built, and equipped so as to conform with all applicable
regulations adopted by the Air Resources Board; that it is free from defects in material
and workmanship that could cause the failure of a warranted part; and that it is
identical in all material respects to the engine described in the manufacturer's
application for certification. The warranty period begins on the date the engine is
originally purchased.
The warranty on emissions-related parts is as follows:
Any warranted part that is not scheduled for replacement as required
maintenance in the Operator's Manual supplied, is warranted for the warranty
period stated above. If any such part fails during the period of warranty
coverage, the part will be repaired or replaced by B&S at no charge to the
owner. Any such part repaired or replaced under the warranty will be warranted
for the remaining warranty period.
Any warranted part that is scheduled only for regular inspection in the Operator's
Manual supplied, is warranted for the warranty period stated above. Any such
part repaired or replaced under warranty will be warranted for the remaining
warranty period.
Any warranted part that is scheduled for replacement as required maintenance
in the Operator's Manual supplied, is warranted for the period of time prior to
the first scheduled replacement point for that part. If the part fails prior to the
first scheduled replacement, the part will be repaired or replaced by B&S at no
charge to the owner. Any such part repaired or replaced under warranty will
be warranted for the remainder of the period prior to the first scheduled
replacement point for the part.
Add-on or modified parts that are not exempted by the Air Resources Board
may not be used. The use of any non-exempted add-on or modified parts by
the owner will be grounds for disallowing a warranty claim. The manufacturer
will not be liable to warrant failures of warranted parts caused by the use of a
non-exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the failure
of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine warranty
policy. Warranty coverage does not apply to failures of emissions parts that are not
original equipment B&S parts or to parts that fail due to abuse, neglect, or improper
maintenance as set forth in the B&S engine warranty policy. B&S is not liable for
warranty coverage of failures of emissions parts caused by the use of add-on or
modified parts.
Look For Relevant Emissions Durability Period and Air Index
Information On Your Small Off-Road Engine Emissions Label
Engines that are certified to meet the California Air Resources Board (CARB) small off-
road Emissions Standard must display information regarding the Emissions Durability
Period and the Air Index. Briggs & Stratton makes this information available to the consumer
on our emissions labels. The engine emissions label will indicate certification information.
The Emissions Durability Period describes the number of hours of actual running time
for which the engine is certified to be emissions compliant, assuming proper maintenance
in accordance with the Operator's Manual. The following categories are used:
Moderate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for 50
hours of actual engine running time. Engines greater than 80 cc displacement are certified
to be emissions compliant for 125 hours of actual engine running time.
Intermediate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for 125
hours of actual engine running time. Engines greater than 80 cc displacement are certified
to be emissions compliant for 250 hours of actual engine running time.
Extended:
Engines at or less than 80 cc displacement are certified to be emissions compliant for 300
hours of actual engine running time. Engines greater than 80 cc displacement are certified
to be emissions compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year. Therefore,
the Emissions Durability Period of an engine with an intermediate rating would equate
to 10 to 12 years.
Briggs & Stratton engines are certified to meet the United States Environmental Protection
Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions Compliance
Period referred to on the Emissions Compliance label indicates the number of operating
hours for which the engine has been shown to meet Federal emissions requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80008256 (Rev F)
California, U.S. EPA, and Briggs & Stratton Corporation Emissions
Control Warranty Statement - Your Warranty Rights and
Obligations
For Briggs & Stratton Engine Models with "B" or "G" Trim Designation (Model-Type-
Trim Representation xxxxxx xxxx Bx or xxxxxx xxxx Gx)
The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are pleased
to explain the emissions control system warranty on your Model Year 2017-2019 engine.
In California, new small off-road engines and large spark ignited engines less than or equal
to 1.0 liter must be designed, built, and equipped to meet the State's stringent anti-smog
standards. B&S must warrant the emissions control system on your engine for the periods
of time listed below provided there has been no abuse, neglect, or improper maintenance
of your engine.
Your exhaust emissions control system may include parts such as the carburetor or fuel
injection system, ignition system, and catalytic converter. Also included may be hoses,
belts, connectors, sensors, and other emissions-related assemblies.
Where a warrantable condition exists, B&S will repair your engine at no cost to you including
diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
Small off-road engines and large spark ignited engines less than or equal to 1.0 liter, and
any related emissions components of the equipment, are warranted for two years, or for
the time period listed in the respective engine or product warranty statement, whichever
is greater. If any emissions-related part on your B&S engine is defective, the part will be
repaired or replaced by B&S.
Owner’s Warranty Responsibilities:
As the engine owner, you are responsible for the performance of the required
maintenance listed in your Operator's Manual. B&S recommends that you retain all
receipts covering maintenance on your engine, but B&S cannot deny warranty solely
for the lack of receipts or your failure to ensure the performance of all scheduled
maintenance.
11
Not for
Reproduction
As the engine owner, you should however be aware that B&S may deny you warranty
coverage if your engine or a part has failed due to abuse, neglect, improper
maintenance, or unapproved modifications.
You are responsible for presenting your engine to a B&S distribution center, servicing
dealer, or other equivalent entity, as applicable, as soon as a problem exists. The
warranty repairs should be completed in a reasonable amount of time, not to exceed
30 days. If you have any questions regarding your warranty rights and responsibilities,
you should contact B&S at 1-800-444-7774 (in USA) or
BRIGGSandSTRATTON.COM.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty Coverage.
It is in addition to the B&S engine warranty for non-regulated engines found in the Operator's
Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the emissions
control systems parts) to the extent these parts were present on the B&S engine.
a. Fuel Metering System
Cold start enrichment system (soft choke)
Carburetor or fuel injection system
Oxygen sensor
Electronic control unit
Fuel pump module
b. Air Induction System
Air cleaner
Intake manifold
c. Ignition System
Spark plug(s)
Magneto ignition system
d. Catalyst System
Catalytic converter
Exhaust manifold
Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
Vacuum, temperature, position, time sensitive valves and switches
Connectors and assemblies
2. Length of Coverage
Coverage is for a period of two years from date of original purchase, or for the time
period listed in the respective engine or product warranty statement, whichever is
greater. B&S warrants to the original purchaser and each subsequent purchaser that
the engine is designed, built, and equipped so as to conform with all applicable
regulations adopted by the Air Resources Board; that it is free from defects in material
and workmanship that could cause the failure of a warranted part; and that it is
identical in all material respects to the engine described in the manufacturer's
application for certification. The warranty period begins on the date the engine is
originally purchased.
The warranty on emissions-related parts is as follows:
Any warranted part that is not scheduled for replacement as required
maintenance in the Operator's Manual supplied, is warranted for the warranty
period stated above. If any such part fails during the period of warranty
coverage, the part will be repaired or replaced by B&S at no charge to the
owner. Any such part repaired or replaced under the warranty will be warranted
for the remaining warranty period.
Any warranted part that is scheduled only for regular inspection in the Operator's
Manual supplied, is warranted for the warranty period stated above. Any such
part repaired or replaced under warranty will be warranted for the remaining
warranty period.
Any warranted part that is scheduled for replacement as required maintenance
in the Operator's Manual supplied, is warranted for the period of time prior to
the first scheduled replacement point for that part. If the part fails prior to the
first scheduled replacement, the part will be repaired or replaced by B&S at no
charge to the owner. Any such part repaired or replaced under warranty will
be warranted for the remainder of the period prior to the first scheduled
replacement point for the part.
Add-on or modified parts that are not exempted by the Air Resources Board
may not be used. The use of any non-exempted add-on or modified parts by
the owner will be grounds for disallowing a warranty claim. The manufacturer
will not be liable to warrant failures of warranted parts caused by the use of a
non-exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the failure
of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine warranty
policy. Warranty coverage does not apply to failures of emissions parts that are not
original equipment B&S parts or to parts that fail due to abuse, neglect, or improper
maintenance as set forth in the B&S engine warranty policy. B&S is not liable for
warranty coverage of failures of emissions parts caused by the use of add-on or
modified parts.
Look For Relevant Emissions Durability Period and Air Index
Information On Your Small Off-Road Engine Emissions Label
Engines that are certified to meet the California Air Resources Board (CARB) small off-
road Emissions Standard must display information regarding the Emissions Durability
Period and the Air Index. Briggs & Stratton makes this information available to the consumer
on our emissions labels. The engine emissions label will indicate certification information.
The Emissions Durability Period describes the number of hours of actual running time
for which the engine is certified to be emissions compliant, assuming proper maintenance
in accordance with the Operator's Manual. The following categories are used:
Moderate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for 50
hours of actual engine running time. Engines greater than 80 cc displacement are certified
to be emissions compliant for 125 hours of actual engine running time.
Intermediate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for 125
hours of actual engine running time. Engines greater than 80 cc displacement are certified
to be emissions compliant for 250 hours of actual engine running time.
Extended:
Engines at or less than 80 cc displacement are certified to be emissions compliant for 300
hours of actual engine running time. Engines greater than 80 cc displacement are certified
to be emissions compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year. Therefore,
the Emissions Durability Period of an engine with an intermediate rating would equate
to 10 to 12 years.
Briggs & Stratton engines are certified to meet the United States Environmental Protection
Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions Compliance
Period referred to on the Emissions Compliance label indicates the number of operating
hours for which the engine has been shown to meet Federal emissions requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80008114 (Rev F)
12 BRIGGSandSTRATTON.com
Not for
Reproduction
Copyright © Briggs & Stratton Corporation, Milwaukee, WI, USA. Alle rettigheder
forbeholdes.
Denne vejledning indeholder sikkerhedsoplysninger, der skal gøre dig opmærksom de
farer og risici, der er forbundet med motorer, samt hvordan de kan undgås Den indeholder
også instrukser om korrekt brug og pleje af motoren. Eftersom Briggs & Stratton ikke
nødvendigvis ved, hvilket udstyr denne motor skal drive, er det vigtigt, at du læser og
forstår denne vejledning og vejledningen til det udstyr, som motoren driver. Gem de
originale anvisninger til fremtidig brug.
Bemærk:
Figurerne og illustrationerne i denne vejledning er udelukkende til referencebrug
og kan være anderledes end din model. Henvend dig hos din forhandler hvis du har nogen
spørgsmål.
For at kunne reservedele eller teknisk assistance fremover skal du her anføre motorens
model-, type- og kodenummer sammen med købsdatoen Disse tal er placeret motoren
(se afsnittet
Udstyr og betjeningselementer
).
Købsdato
Motormodel - Type - Trim
Motorserienummer
Kig efter 2D-stregkoden, der er placeret
visse maskiner. Når den ses en enhed
med 2D viser koden vores websted, hvor du
kan adgang til supportoplysninger for dette
produkt. Omkostninger til datatrafik kan
forekomme. Nogle lande har ikke adgang til
online supportoplysninger.
Information om genbrug
Al emballage, brugt olie og batterier skal bortskaffes med
henblik genbrug i henhold til de gældende
regeringsvedtægter.
Førersikkerhed
Sikkerhedssymboler og signalord
Sikkerhedssymbolet anvendes til at identificere sikkerhedsoplysninger om farer, der
kan medføre personskader. Et signalord (FARE, ADVARSEL eller FORSIGTIG) bruges
sammen med advarselssymbolet til at identificere sandsynligheden og den mulige
sværhedsgrad af personskaden. Desuden kan et faresymbol bruges til at repræsentere
typen af fare.
FARE angiver en farlig situation, som vil medføre død eller alvorlig personskade,
hvis den ikke undgås.
ADVARSEL angiver en farlig situation, som kan medføre død eller alvorlig
personskade, hvis den ikke undgås.
FORSIGTIG angiver en farlig situation, som kan medføre alvorlig eller moderat
personskade, hvis den ikke undgås.
BEMÆRK
angiver en situation, som kan medføre beskadigelse af produktet.
Faresymboler og deres betydninger
BetydningSymbolBetydningSymbol
Læs og forstå
brugervejledningen, før brug af
eller servicering af enheden.
Sikkerhedsoplysninger om
farer, der kan medføre
personskade.
BetydningSymbolBetydningSymbol
Risiko for eksplosion.Brandfare
Fare for giftig røgFare for stød
Støjfare Høreværn anbefales
ved længere brug.
Fare ved varm overflade
Risiko for eksplosion.Fare for flyvende genstande
Bær beskyttelsesbriller.
Fare for tilbageslagFare for forfrysning
KemikaliefareFare for amputation
Bevægelige dele
KorroderendeFare for varme
Sikkerhedsmeddelelser
ADVARSEL
Visse dele dette produkt og dets tilbehør indeholder kemikalier, som ifølge staten
Californien kan forårsage kræft, fosterskader eller forplantningsskader. Vask hænder
efter håndtering.
ADVARSEL
Udstødningen fra motoren dette produkt indeholder kemikalier, som ifølge staten
Californien kan forårsage kræft, fosterskader eller forplantningsskader.
ADVARSEL
Briggs & Stratton-motorer er ikke designet til og ikke bruges til at drive: fun-karts;
go-karts; terrængående børne-, fritids- eller sportskøretøjer (ATV'er); motorcykler,
luftpudefartøjer; luftfartsprodukter eller køretøjer, der anvendes til konkurrenceformål,
som ikke er sanktioneret af Briggs & Stratton. Se www.briggsracing.com for yderligere
oplysninger om motorsportsprodukter. For brug med terrængående og side-by-side
ATV'er kontakt Briggs & Stratton Engine Application Center, 1-866-927-3349. Ukorrekt
motorbrug kan resultere i alvorlig personskade eller død.
ADVARSEL
Benzin og benzindampe er yderst brandfarlige og eksplosive.
Brand eller eksplosion kan medføre alvorlige forbrændinger eller død.
Under påfyldning af brændstof
Sluk motoren, og lad den køle af i mindst to minutter, før benzindækslet fjernes.
Påfyld brændstof udendørs eller et godt udluftet område.
Overfyld ikke brændstoftanken. Fyld ikke over bund brændstoftankens hals for at
tillade ekspansion brændstof.
Hold benzin væk fra gnister, åben ild, tændflammer, varme eller andre
antændelseskilder.
Kontroller hyppigt brændstofledninger, tank, dæksel og beslag for revner eller
lækage. Udskift efter behov.
13
Not for
Reproduction
Hvis der bliver spildt brændstof, skal du vente til det er fordampet, før motoren
startes.
Når motoren startes
Sørg for at tændrør, lydpotte, brændstofdæksel og luftfilter (hvis monteret) er
plads og er fastspændte.
Prøv ikke at starte motoren med tændrøret fjernet.
Hvis motoren er druknet, sæt chokeren (hvis den findes) åbn- / kør-stilling,
sæt speederen (hvis den findes) over i hurtig stilling, og bliv ved, indtil den starter.
Ved betjening af udstyret
Undgå at vippe motoren eller udstyret, således at brændstoffet løber ud.
Brug ikke chokeren til at standse motoren.
Start aldrig motoren, og lad aldrig motoren køre med luftfilterenheden (hvis monteret)
eller luftfiltret (hvis monteret) fjernet.
Under olieskift
Hvis du tømmer olien fra oliepåfyldningsrøret i toppen, skal brændstoftanken være
tom, da brændstoffet ellers kan løbe ud og resultere i brand eller eksplosion.
Når enheden vippes ved vedligeholdelse
Når der udføres vedligeholdelse, der kræver, at enheden vippes, skal
brændstoftanken, hvis monteret motoren, være tom, da brændstoffet ellers kan
løbe ud og resultere i brand eller eksplosion.
Under transport af udstyr
Transport med TOM brændstoftank eller med brændstofventilen i stillingen CLOSED.
Opbevaring af brændstof eller redskaber med brændstof i tanken
Opbevares afstand af fyr, ovne, vandvarmere eller andet udstyr, som kan have
en tændflamme eller anden antændelseskilde, da de kan antænde benzindampe.
ADVARSEL
Start af motoren forårsager gnistdannelse.
Gnister kan antænde brændbare luftarter i nærheden.
Dette kan resultere i eksplosion og brand.
Hvis der er en lækage af natur- eller flaskegas i området, motoren ikke startes.
Brug ikke startvæsker under tryk, da dampene er brændbare.
ADVARSEL
FARE FOR GIFTIGE GASSER. Motorudstødning indeholder kulilte, som er en
giftig gas, der kan dræbe minutter. Du kan hverken se, lugte eller smage
det. Selv om du ikke kan lugte udstødningsgasser, kan du stadigvæk være udsat
for kulilteforgiftning. Hvis du begynder at kvalme, føle dig svimmel eller svag,
mens du bruger maskinen, skal du have frisk luft MED DET SAMME. Søg
lægehjælp. Du kan være udsat for kulilteforgiftning.
Betjen KUN denne maskine udendørs langt væk fra døre, vinduer og ventilatorer
for at undgå, at kuliltegasser samler sig og evt. driver hen imod steder, hvor folk
befinder sig.
Installer batteridrevne kuliltealarmer eller strømtilsluttede alarmer med batterisupport
i henhold til producentens vejledning. Røgalarmer kan ikke registrere kulilte.
DU IKKE betjene denne maskine indendørs i hjem, garager, kældre,
krybekældre, skure eller andre delvist lukkede steder, også selvom du bruger
ventilatorer eller har åbne døre og vinduer for at sikre ordentlig ventilation. Kulilte
kan hurtigt akkumuleres sådanne steder og kan vare ved i timevis, efter at
maskinen er blevet afbrudt.
Anbring ALTID denne maskine i vindretningen, og sørg for, at udstødningen peger
væk fra steder, hvor der er folk til stede.
ADVARSEL
Hurtig tilbagetrækning af startsnoren (tilbageslag) vil bevirke, at din hånd og
arm bliver trukket hurtigere mod motoren, end du kan kontrollere.
Konsekvenserne kan være brækkede knogler, skrammer eller forstuvninger.
Når du starter motoren, træk langsomt i startsnoren, indtil der mærkes modstand,
og træk kraftigt for at undgå tilbageslag.
Fjern alle ydre anordninger / belastninger motoren, før du starter den.
Direkte tilkoblede dele udstyret f.eks. skæreknive, skovlhjul, remskiver, kædehjul
osv. skal være forsvarligt monteret.
ADVARSEL
Roterende dele kan komme i kontakt med eller gribe hænder, fødder, hår,
beklædning og smykker.
Dette kan medføre, at legemsdele skæres af, eller at brugeren får alvorlige snitsår.
Redskaber kun anvendes med alle sikkerhedsafskærmninger plads.
Hold hænder og fødder i sikker afstand fra roterende dele.
Bind langt hår op, og fjern smykker.
Undgå at bære løstsiddende tøj, tøj med snore eller andre genstande, der kan
sætte sig fast i de roterende dele.
ADVARSEL
Kørende motorer danner varme. Motordele, især lydpotte, bliver ekstremt varme.
Alvorlige forbrændinger kan opstå ved kontakt.
Brændbart affald såsom blade, græs, krat osv. kan blive antændt.
Lad lydpotte, motorcylinder og køleribber køle af, før du rører ved dem.
Fjern brændbart materiale fra området omkring lydpotten og cylinderen.
Det er en overtrædelse af staten Californiens forskrifter om offentlige ressourcer,
afsnit 4442 at bruge eller betjene motoren ethvert skov-, krat- eller græsdækket
område medmindre udstødningssystemet er forsynet med en korrekt vedligeholdt
gnistfanger, som beskrevet i afsnit 4442. Andre stater eller forbundsområder kan
have tilsvarende love. Kontakt en autoriseret fabrikant eller serviceforhandler
angående anskaffelse af en gnistfanger, der er konstrueret til det udstødningssystem,
der er monteret den pågældende maskine.
ADVARSEL
Utilsigtede gnister kan resultere i brand eller elektrisk stød.
Utilsigtet start kan resultere i indvikling, traumatisk amputation eller lemlæstelse.
Brandfare
Inden påbegyndelse af justeringer eller reparationer:
Fjern tændrørskablet, og hold det behørig afstand af tændrøret.
Frakobl batteriet den negative terminal (gælder kun motorer med elektrisk start).
Brug passende værktøjer.
Undlad at røre ved regulatorfjederen, forbindelser eller andre dele, der er med til
at øge motorens hastighed.
Reservedelene skal have samme udformning, og de skal placeres præcist
samme måde som de originale dele. Andre reservedele vil ikke give den samme
ydelsesgrad, kan ødelægge maskinen og resultere i personskade.
Slå aldrig svinghjulet med en hammer eller en hård genstand, da dette kan
svinghjulet til at splintres under drift.
Under test af gnister:
Brug en godkendt tændrørstester.
Test ikke for gnister med tændrøret fjernet.
Funktioner og
betjeningsanordninger
Motorens betjeningselementer
Sammenlign illustrationen (Figur: 1, 2) med din motor for at lære placeringen af udstyr og
betjeningselementer.
A. Identifikation af motoren Model-, type- og kodenummer
B. Tændrør
C. Choker
14 BRIGGSandSTRATTON.com
Not for
Reproduction
D. Primer
E. Brændstofhane
F. Startsnorgreb
G. Luftindsugningsgitter
H. Brændstoftank og tankdæksel
I. Oliepind/oliepåfyldningsrør
J. Olieaftapningsprop
K. Lyddæmper, lyddæmperskærm (hvis monteret), gnistfanger (hvis monteret)
L. Sikkerhedsnøgle (hvis monteret):
1
M. Trykknap-el-start
N. Strømkablets kontakt - 120 Volt
O. Strømkablets kontakt - 230 Volt
P. Elstarter
Q. Gasregulator (hvis monteret)
1
R. Sikkerhedsnøgle (hvis monteret):
1
1
Nogle motorer og noget udstyr har fjernbetjening. Se udstyrsmanualen for placering
og betjening af fjernbetjeningen.
Motorfaresymboler og deres betydninger
BetydningSymbolBetydningSymbol
Motorhastighed - LANGSOMMotorhastighed - HURTIG
TIL - FRAMotorhastighed - STOP
Motorstart - choker ÅBENMotorstart - choker LUKKET
Brændstofhane - LUKKETBrændstofdæksel
Brændstofhane - ÅBEN
Brændstofniveau - maks.
Undgå at overfylde
Betjening
Olieanbefalinger
Oliekapacitet: Se afsnittet
Specifikationer
.
BEMÆRK
Denne motor blev leveret af Briggs & Stratton uden olie. Producenter eller forhandlere
af udstyret kan have fyldt olie motoren. Inden du starter motoren første gang, skal
du sørge for at kontrollere oliestanden og påfylde olie i overensstemmelse med
anvisningerne i denne manual. Hvis du starter motoren uden olie, vil den blive beskadiget
uden mulighed for at reparere den, og det er ikke omfattet af garantien.
Vi anbefaler at bruge olie, der er garantigodkendt af Briggs & Stratton for at opnå den
bedste ydeevne. Andre selvrensende olier af høj kvalitet er acceptable, hvis de er godkendt
til SF-, SG-, SH-, SJ-service eller højere. Undlad at bruge specielle tilsætningsstoffer.
Udendørstemperatuer er afgørende for den passende olieviskositet til motoren. Brug
tabellen til at vælge den bedste viskositet til det forventede udendørs temperaturinterval.
Motorer i det meste udstyr til udendørs brug kører godt med syntetisk olie 5W-30. Til udstyr,
der bruges i varmere temperaturer, yder Vanguard™ 15W-50 syntetisk olie den bedste
beskyttelse.
SAE 30 - Under 4 °C (40 °F) vil brugen af SAE 30 gøre det svært at starte.A
10W-30 - Over 27 °C (80 °F) kan brugen af 10W-30 medføre forhøjet olieforbrug.
Kontrollér oliestanden oftere.
B
5W-30C
Syntetisk 5W-30D
Vanguard™ syntetisk 15W-50E
Kontrollér oliestand
Se figur: 3, 4
Før påfyldning eller kontrol af olien
Kontrollér, at motoren står plant.
Rengør oliepåfyldningområdet for affaldsrester.
Kort oliepind (hvis monteret)
1. Fjern oliepinden (A, figur 3) ud, og tør den af med en ren klud.
2. Monter oliepinden (A, figur 3). ikke drejes eller strammes.
3. Træk oliepinden op, og kontroller oliestanden. Du finder den korrekte oliestand øverst
indikatoren for fuld (B, figur 3) oliepinden.
4. Hvis oliestanden er for lav, skal du langsomt påfylde olie i motoroliepåfyldningen (C,
figur 3). Fyld, indtil olien løber over.
5. Sæt oliepinden plads, og spænd den igen (A, figur 3).
Forlænget oliepind (hvis monteret)
1. Fjern oliepinden (A, figur 4) ud, og tør den af med en ren klud.
2. Sæt oliepinden i, og spænd den (A, figur 4).
3. Træk oliepinden op, og kontroller oliestanden. Du finder den korrekte oliestand øverst
indikatoren for fuld (B, figur 4) oliepinden.
4. Hvis oliestanden er for lav, skal du langsomt påfylde olie i motoroliepåfyldningen (C,
figur 4). Undgå at overfylde. Efter oliepåfyldningen vent et minut, og kontroller
oliestanden.
5. Sæt oliepinden plads, og spænd den igen (A, figur 4).
Beskyttelsessystem for lav oliestand (hvis
monteret)
Nogle motorer er udstyret med en sensor for lav oliestand. Hvis oliestanden er lav, aktiverer
sensoren enten et advarselslys eller standser motoren. Stands motoren, og følg disse trin,
før du genstarter motoren.
Kontrollér, at motoren står plant.
kontroller derefter oliestanden. Se afsnittet
Kontrollér oliestand
.
Hvis oliestanden er lav, tilføj den korrekte mængde olie. Start motoren, og sørg
for, at advarselslyset (hvis monteret) ikke er aktiveret.
Hvis oliestanden ikke er lav, du ikke starte motoren. Kontakt en autoriseret
forhandler fra Briggs & Stratton for at rettet olieproblemet.
Anbefalet brændstof
Brændstoffet skal opfylde disse krav:
Ren, frisk blyfri benzin.
Minimum 87 oktan/87 AKI (91 RON). Anvendelse i store højder; se nedenfor.
15
Not for
Reproduction
Benzin med op til 10 % etanol (gasohol) er acceptabelt.
BEMÆRK
Der ikke bruges ikke-godkendt benzin, som for eksempel E85. Der
ikke blandes olie i benzin, og der ikke foretages ændringer motoren for at køre
med alternative brændstoffer. Brug af ikke-godkendt brændstof resulterer i skader
motorkomponenterne, som ikke vil være dækket af garantien.
For at beskytte brændstofsystemet mod dannelse af gummi kan en stabilisator iblandes
brændstoffet. Se
Opbevaring.
Brændstoffer er forskellige. Såfremt du oplever start- eller
driftsproblemer, skift brændstof leverandør eller mærke. Motoren er certificeret til drift
med benzin. Emissionskontrolsystemet for denne motor er EM (Engine Modifications).
Højder
Ved højder over 1.524 m (5.000 fod) er en minimum 85 oktan/85 AKI (89 RON) benzin
acceptabel.
Til karburatormotorer kræves justering ved anvendelse i store højder for at opretholde
driften. Drift uden disse justeringer vil medføre en nedgang i ydelse, en stigning i
brændstofforbrug og øget emissioner. Besøg en autoriseret forhandler Briggs & Stratton
for at oplysninger om højde tilpasning. Drift af en motor, der er justeret til store højder,
kan ikke anbefales i højder under 762 m (2.500 fod).
For motorer med elektronisk brændstofindsprøjtning (EFI), er det ikke nødvendigt at udføre
justering ved anvendelse i store højder.
Påfyld brændstof
Se figur: 5
ADVARSEL
Benzin og benzindampe er yderst brandfarlige og eksplosive.
Brand eller eksplosion kan medføre alvorlige forbrændinger eller døden.
Under påfyldning af brændstof
Sluk motoren og lad den køle af i mindst 2 minutter, før benzindækslet fjernes.
Påfyld brændstof udendørs eller et godt udluftet område.
Overfyld ikke brændstoftanken. For at give plads til udvidelse skal du undlade at
fylde op over bunden af tankens brændstofkant.
Hold benzin væk fra gnister, åben ild, tændflammer, varme eller andre
antændelseskilder.
Kontroller hyppigt brændstofledninger, tank, dæksel og beslag for revner eller lækage.
Udskift efter behov.
Hvis der bliver spildt brændstof, skal du vente til det er fordampet, før motoren startes.
1. Rengør brændstofdækslet for snavs og affaldsrester. Fjern brændstofsdækslet.
2. Påfyld brændstoftanken (A, figur 5) med brændstof. For at give plads til udvidelse,
undlad at fylde op over bunden af tankens brændstofkant (B).
3. Sæt dækslet tilbage plads.
Start og stop motoren
Se Figur: 6, 7
Start motoren
ADVARSEL
Hurtig tilbagetrækning af startsnoren (tilbageslag) vil bevirke, at din hånd og arm
bliver trukket hurtigere mod motoren end du kan kontrollere.
Konsekvenserne kan være brækkede knogler, skrammer eller forstuvninger.
Når du starter motoren, træk langsomt i startsnoren indtil der mærkes modstand,
og træk kraftigt for at undgå tilbageslag.
ADVARSEL
Brændstof og brændstofdampe er yderst brandfarlige og eksplosive.
Brand eller eksplosion kan medføre alvorlige forbrændinger eller døden.
Når motoren startes
Sørg for at tændrør, lydpotte, brændstofdæksel og luftfilter (hvis monteret) er
plads og er fastspændte.
Prøv ikke at starte motoren med tændrøret fjernet.
Hvis motoren er druknet, sæt chokeren (hvis monteret) ÅBEN/KØR position,
bevæg speederen (hvis monteret) over positionen HURTIG, og bliv ved, indtil
den starter.
ADVARSEL
FARE FOR GIFTIGE GASSER. Motorudstødning indeholder kulilte, som er en giftig
gas, der kan dræbe minutter. Du KAN HVERKEN se det, lugte det eller smage
det. Selv om du ikke kan lugte udstødningsgasser, kan du stadigvæk være udsat
for kulilteforgiftning. Hvis du begynder at føle dig utilpas, svimmel eller svag
under betjening af denne maskine, skal du stoppe den og sørge for at frisk luft
OMGÅENDE. Søg lægehjælp. Du kan være udsat for kulilteforgiftning.
Dette produkt KUN betjenes udenfor, langt fra vinduer, døre og ventilationsanlæg
for at reducere risikoen for, at der samler sig kulilte, som kan ledes til områder, hvor
der befinder sig folk.
Installer batteridrevne kuliltealarmer eller strømtilsluttede alarmer med batterisupport
i henhold til producentens vejledning. Røgalarmer kan ikke registrere kulilte.
DU IKKE betjene denne maskine indendørs i hjem, garager, kældre, krybekældre,
skure eller andre delvist lukkede steder, også selvom du bruger ventilatorer eller
har åbne døre og vinduer for at sikre ordentlig ventilation. Kulilte kan hurtigt
akkumuleres sådanne steder og kan vare ved i timevis, efter at maskinen er blevet
afbrudt.
Placer ALTID dette produkt i vindretningen, og lad motorens udstødning vende væk
fra områder, hvor der opholder sig folk.
BEMÆRK
Denne motor blev leveret af Briggs & Stratton uden olie. Inden du starter
motoren, skal du sørge for at påfylde olie i overensstemmelse med vejledningerne i
denne manual. Hvis du starter motoren uden olie, vil den blive beskadiget uden mulighed
for at reparere den, og det er ikke omfattet af garantien.
Bemærk:
Udstyret kan have fjernbetjening. Se udstyrsmanualen for placering og betjening
af fjernbetjeningen.
1. Kontroller motoroliestanden. Se afsnittet
Kontrol af olieniveau
.
2. Sørg for, at udstyrets kørselsbetjeningsanordninger, hvis monteret, er frakoblet.
3. Sæt gashåndtaget (A, Figur 6), hvis monteret, i stillingen HURTIG. Betjen motoren
i positionen HURTIG.
4. Sæt brændstofhanen (B, Figur 6) i stillingen ÅBEN, hvis monteret.
5. Tændingskontakt, hvis monteret: Sæt nøglen i, (C, Figur 6), og drej den til stillingen
ÅBEN
Sikkerhedsnøgle (hvis monteret): Tryk sikkerhedsnøglen (D).
6. Flyt chokerregulatoren (E, Figur 6) til positionen CHOKE.
Bemærk:
Det er normalt ikke nødvendigt at bruge choker, når man genstarter en varm
motor.
7. Tryk primeren (F, Figur 6) to (2) gange.
Bemærk:
Spædning er normalt ikke nødvendig, når en varm motor skal genstartes.
8. Genstart, hvis monteret: Tag fat om startsnorens håndtag med et fast greb (G,
Figur 7). Træk langsomt i startsnorens håndtag, indtil der mærkes modstand, og
træk kraftigt til.
ADVARSEL
Hurtig tilbagetrækning af startsnoren (tilbageslag) vil bevirke, at din hånd og arm bliver
trukket hurtigere mod motoren, end du kan kontrollere. Konsekvenserne kan være
brækkede knogler, skrammer eller forstuvninger. Når du starter motoren, træk
langsomt i startsnoren indtil der mærkes modstand, og træk kraftigt for at undgå
tilbageslag.
9. Elstarter, hvis monteret: Sæt forlængerledningen i strømkablets kontakt (H, 120
Volt) eller (J, 230 Volt), og sæt den derefter i kontakten væggen (Figur 7). Tryk
knappen ind (K). Når motoren starter, afbrydes forlængerledningen fra kontakten i
væggen og fra strømkablets kontakt (H, J).
Bemærk:
Hvis der er behov for en ekstra forlængerledning, skal man sørge for at anvende
en jordet 3-leder forlængerledning.
ADVARSEL
Hvis forlængerledningen er beskadiget, skal den udskiftes af producenten eller dennes
servicerepræsentant eller en person med tilsvarende kvalifikationer for at undgå en
farlig situation.
16 BRIGGSandSTRATTON.com
Not for
Reproduction
BEMÆRK
Starterens levetid kan forlænges ved at bruge korte startcyklusser (maks.
fem sekunder). Vent ét minut mellem startcyklusserne.
10. Når motoren bliver varm, flyttes chokerregulatoren (E, Figur 6) til stillingen KØR.
Bemærk:
Hvis motoren ikke starter efter gentagne forsøg, skal du kontakte din lokale
forhandler eller til BRIGGSandSTRATTON.com eller ringe til 1-800-233-3723 (i
USA).
Stop motoren
ADVARSEL
Brændstof og brændstofdampe er yderst brandfarlige og eksplosive.
Brand eller eksplosion kan medføre alvorlige forbrændinger eller døden.
Brug ikke chokeren til at stoppe motoren.
1. Tændingskontakt, hvis monteret: Drej nøglen (C, Figur 6), til stillingen FRA. Tag
nøglen ud og opbevar den et sikkert sted uden for børns rækkevidde.
Sikkerhedsnøgle (hvis monteret): Tag nøglen (D) ud og opbevar den et sikkert
sted uden for børns rækkevidde.
2. Efter at motoren standser, drej brændstofhanen (B, Figur 6), hvis monteret, til stillingen
LUKKET.
Vedligeholdelse
BEMÆRK
Hvis græsslåmaskinen hældes under vedligeholdelse, skal brændstoffet
udtømmes og tændrørssiden skal vende op. Hvis brændstoftanken ikke er tom og hvis
motoren bliver hældet i en anden retning, kan det være svært at starte motoren pga.
olie eller brændstof forurener luftfilteret og/eller tændrøret.
ADVARSEL
Når der udføres vedligeholdelse, der kræver, at enheden vippes, skal brændstoftanken
være tom, da brændstoffet ellers kan løbe ud og resultere i brand eller eksplosion.
Vi anbefaler, at du kontakter en autoriseret serviceforhandler fra Briggs & Stratton
vedrørende al vedligeholdelse og service af motoren og motordele.
BEMÆRK
Alle dele i denne motor skal være korrekt placeret for at give korrekt
funktion.
ADVARSEL
Gnister, som frembringes ved et uheld, kan medføre brand eller stød.
Uplanlagt start kan resultere i indvikling, traumatisk amputation eller lemlæstelse.
Brandfare
Inden påbegyndelse af justeringer eller reparationer:
Fjern tændrørskablet og hold det behørig afstand af tændrøret.
Tag minuskablet af batteriet, hvis motoren er udstyret med el-starter.
Brug passende redskaber.
FORETAG ALDRIG ændring af regulatorfjederen, forbindelser eller andre dele for
at øge motorens omdrejningstal.
Reservedelene skal have samme udformning og de skal placeres præcist samme
måde som de originale dele. Andre reservedele vil ikke give den samme ydelsesgrad,
kan ødelægge maskinen og resultere i personskade.
Slå aldrig svinghjulet med en hammer eller en hård genstand, da dette kan
svinghjulet til at splintres under drift.
Under test af gnister:
Brug en godkend tændrørstester.
Test ikke for gnist med tændrøret fjernet.
Udførelse af udledningskontrol
Vedligeholdelse, udskiftning eller reparation af udledningskontrolenheder og
systemer kan udføres af et ikke autoriseret værksted eller af en enkeltperson. For
at udført udledningskontrolservice "uden beregning" skal arbejdet imidlertid udføres af
en autoriseret forhandler. Se erklæringer om udledningskontrol.
Vedligeholdelsesskema
Første 5 timer
Skift olie
Hver 8. time eller dagligt
Kontrollér motorens oliestand
For hver 50 driftstimer eller én gang årligt
Skift motorolie
Kontrollér lydpotte og lyddæmperskærm
Årligt
Udskifte tændrør
Kontroller ventilspillerum.
1
1
Ikke nødvendigt, medmindre der konstateres problemer mht. motorydelse.
Karburator og motorhastighed
Foretag aldrig justering af karburator og motorhastighed. Karburatoren er fabriksindstillet
til at virke effektivt under de fleste omstændigheder. Undlad at røre ved regulatorfjederen,
forbindelser eller andre dele der er med til at øge motorens hastighed. Hvis der er behov
for justering, kontakt en autoriseret serviceforhandler fra Briggs & Stratton for service.
BEMÆRK
Denne udstyrsfabrikant specificerer maks. hastighed for motoren, som er
installeret udstyret. Overskrid ikke denne hastighed. Hvis du ikke er sikker på, hvad
maks. hastigheden er udstyret, eller hvilken motorhastighed, der er indstillet fra
fabrikken af, kontakt en autoriseret serviceforhandler fra Briggs & Stratton for hjælp.
For sikker og korrekt brug af udstyret, skal motorhastigheden kun justeres af en uddannet
servicetekniker.
Servicer tændrør
Se figur: 8
Kontroller afstanden (A, figur 8) med en afstandsmåler (B). Om nødvendigt genindstil
afstanden. Monter og fastspænd tændrøret til det anbefalede moment. Mht.
afstandsindstilling og moment, se afsnittet
Specifikationer
.
Bemærk:
Nogle steder kræver lokal lovgivning anvendelse af et modstands tændrør for
at undertrykke tændingssignaler. Hvis motoren oprindeligt var udstyret med et modstands
tændrør, brug den samme type når du udskifter.
Servicering af udstødningssystem
ADVARSEL
Kørende motorer danner varme. Motordele, især lydpotten, bliver ekstremt varme.
Kontakt med varme dele kan forårsage alvorlige forbrændinger.
Der kan ild i brændbart affald, som f.eks. blade, græs og grene.
Lad lydpotte, motorcylinder og køleribber køle af, før du rører ved dem.
Fjern brændbart materiale fra området omkring lydpotten og cylinderen.
Det er en overtrædelse af staten Californiens offentlige ressource forskrifter, afsnit
4442 at bruge eller betjene motoren ethvert skov-, krat- eller græsdækket område
medmindre udstødningssystemet er forsynet med en korrekt vedligeholdt gnistfanger,
som beskrevet i afsnit 4442. Andre stater eller forbundsområder kan have tilsvarende
love. Kontakt en autoriseret serviceforhandler angående anskaffelse af en gnistfanger,
der er konstrueret til det udstødningssystem, der er monteret den pågældende
maskine.
Fjern brændbart materiale fra området omkring lydpotten og cylinderen. Kontrollér lydpotten
for revner, korrosion eller andre skader. Fjern gnistaflederen, hvis den er monteret, og
kontrollér den for skader eller karbonblokering. Hvis der er skade, skal der monteres
reservedele, før brug.
ADVARSEL
Reservedelene skal have samme udformning og de skal placeres præcist samme
måde som de originale dele. Andre reservedele vil ikke give den samme ydelsesgrad,
kan ødelægge maskinen og resultere i personskade.
17
Not for
Reproduction
Skift motorolie
Se Figur: 9, 10, 11
Brugt olie er et farligt affaldsprodukt og skal bortskaffes passende måde. Undgå at
bortkaste sammen med husholdningsaffald. Undersøg med de lokale myndigheder,
servicecenter eller forhandler hvordan man kan komme af med det en genbrugsstation.
Aftapning af olie
1. Med motoren standset, men stadig varm, trækkes ledningen til tændrøret ud (D,
Figur 9) og holdes væk fra tændrøret (E).
2. Afmonter olieaftapningsproppen (F, Figur 10). Udtøm olien i en godkendt beholder.
Bemærk:
Enhver af disse olieaftapningspropper (G, Figur 10) kan monteres i motoren.
3. Monter og spænd olieaftapningsproppen (F, Figur 10), efter at olien er tappet af.
Påfyldning af olie
Kontrollér, at motoren står plant.
Rengør oliepåfyldningområdet for affaldsrester.
Se
Specifikationsafsnittet
mht. oliekapacitet.
Kort oliepind (hvis monteret)
1. Fjern oliepinden (A, Figur 10), og tør den af med en ren klud.
2. Hæld olie langsomt i motorpåfyldningen (C, Figur 10). Fyld, indtil olien løber over.
3. Monter oliepinden (A, Figur 10). ikke drejes eller strammes. Fjern, og kontroller
oliestanden. Det korrekte olieniveau er for oven indikatoren for fuld (B)
oliemålepinden.
4. Sæt oliepinden plads, og spænd den igen (A, Figur 10).
5. Forbind ledningen til tændrøret (D, Figur 9) med tændrøret (E).
Forlænget oliepind (hvis monteret)
1. Fjern oliepinden (A, Figur 11), og tør den af med en ren klud.
2. Hæld olie langsomt i motorpåfyldningen (C, Figur 11). Undgå at overfylde. Vent et
(1) minut efter oliepåfyldningen, og kontroller oliestanden igen.
3. Sæt oliepinden i, og spænd den (A, Figur 11).
4. Fjern, og kontroller oliestanden. Du finder den korrekte oliestand øverst indikatoren
for fuld (B, Figur 11) oliepinden.
5. Sæt oliepinden plads, og spænd den igen (A, Figur 11).
6. Forbind ledningen til tændrøret (D, Figur 9) med tændrøret (E).
Luftfilter
Motoren er ikke udstyret med et luftfilter. Anvend IKKE denne motor til andet end
snerydning.
Opbevaring
ADVARSEL
Benzin og benzindampe er ekstremt brændbare og eksplosive.
Brand eller eksplosion kan forårsage alvorlige forbrændinger eller dødsfald.
Opbevaring af brændstof eller udstyr med brændstof i tanken
Opbevares afstand af fyr, ovne, vandvarmere eller andet udstyr, som kan have
en tændflamme eller anden antændelseskilde, da de kan antænde benzindampe.
Brændstofsystem
Se figur: 12
Opbevar motoren plant (almindelig driftsposition). Fyld brændstoftanken (A, figur 12) med
brændstof. Fyld ikke over brændstoftankens hals (B), brændstoffet kan ekspandere.
Brændstof kan blive forældet, når det opbevares i over 30 dage. Gammelt brændstof kan
forårsage dannelse af syre- og gummiaflejringer i brændstofsystemet eller væsentlige
karburatordele. For at holde brændstof frisk anvendes Briggs & Stratton Advanced
Formula Fuel Treatment & Stabilizer, som er tilgængelig hvor originale reservedele til
Briggs & Stratton sælges.
Der er ingen grund til at tømme motoren for brændstof, hvis en brændstofstabilisator
anvendes ifølge vejledningen. Lad motoren køre i to minutter for at stabilisatoren kan
cirkulere gennem brændstofsystemet inden opbevaring.
Hvis benzinen i motoren ikke er blevet behandlet med en brændstofstabilisator, skal den
aftappes i en godkendt beholder. Lad motoren køre indtil der ikke er mere brændstof
tilbage. Brugen af en brændstofstabilisator i opbevaringsbeholderen anbefales for at bevare
det frisk.
Motorolie
Skift motorolien, mens motoren stadig er varm. Se afsnittet
Skift motorolie
.
Fejlfinding
Hvis du har brug for hjælp, skal du kontakte din lokale forhandler eller til
BRIGGSandSTRATTON.com eller ringe til 1-800-233-3723 (i USA).
Specifikationer
Model: 100000
9.95 ci (163 cc)Slagvolumen
2.677 in (68,00 mm)Boring
1.77 in (45,00 mm)Slaglængde
18 - 20 oz (,54 - ,59 L)Oliekapacitet
.030 in (,76 mm)Tændrørsgab
180 lb-in (20 Nm)Tilspændingsmoment for tændrør
.010 - .014 in (,25 - ,36 mm)Rotorelektrodeafstand
.004 - .006 in (,10 - ,15 mm)Ventilspillerum (indsugning)
.006 - .008 in (,15 - ,20 mm)Ventilspillerum (udstødning)
Model: 130000
12.69 ci (208 cc)Slagvolumen
2.757 in (70,02 mm)Boring
2.126 in (54,00 mm)Slaglængde
18 - 20 oz (,54 - ,59 L)Oliekapacitet
.030 in (,76 mm)Tændrørsgab
180 lb-in (20 Nm)Tilspændingsmoment for tændrør
.010 - .014 in (,25 - ,36 mm)Rotorelektrodeafstand
.004 - .006 in (,10 - ,15 mm)Ventilspillerum (indsugning)
.006 - .008 in (,15 - ,20 mm)Ventilspillerum (udstødning)
Motoreffekten falder med 3,5 % for hver 300 m over havets overflade og med 1 % for hver
5,6 ºC over 25 ºC. Motoren kan køre tilfredsstillende ved en hældning op til 15°.
Yderligere oplysninger om grænseværdierne for drift hældninger findes i redskabets
betjeningsvejledning.
Reservedele - Model: 100000, 130000
DelnummerReservedel
100117, 100120Advanced Formula Fuel Treatment &
Stabilizer
491055Tændrør med resistor
696202, 5066Long Life Platinum tændrør
89838, 5023Tændrørsnøgle
19368Gnisttester
Vi anbefaler, at du kontakter en autoriseret Briggs & Stratton forhandler vedrørende al
vedligeholdelse og service af motoren og motordele.
Effektangivelse: Bruttoeffekten for hver enkelt benzinmotormodel er afmærket i henhold
til SAE-kode J1940 (Society of Automotive Engineers) - procedure til angivelse af effekt
og moment for små motorer - og angivet i henhold til SAE J1995. Momentværdier afledes
ved 2600 o./min. for motorer med “rpm” mærkaten, og 3060 o./min for alle andre.
Hestekræftværdier afledes ved 3600 o./min. Bruttoeffektkurverne kan ses
www.BRIGGSandSTRATTON.com. Nettoeffektværdier bliver målt med udstødnings- og
18 BRIGGSandSTRATTON.com
Not for
Reproduction
luftfilter monteret, hvorimod bruttoeffektværdier bliver målt uden disse anordninger.
Bruttomotoreffekten vil være højere end den faktiske nettomotoreffekt, som påvirkes bl.a.
af lokale driftsforhold og variationer fra motor til motor. I betragtning af de mange forskellige
produkter, motorerne anvendes i, yder benzinmotoren måske ikke den nominelle
bruttoeffekt, når den anvendes et givent motorredskab. Denne forskel skyldes en lang
række forskellige faktorer, som blandt andet kan omfatte forskelle i motorkomponenter
(luftfilter, udstødning, opladning, køling, karburator, brændstofpumpe osv.),
anvendelsesbegrænsninger, lokale driftsforhold (temperatur, luftfugtighed, højde over
havet) og variationer fra motor til motor. Som følge af produktions- og
kapacitetsbegrænsninger forbeholder Briggs & Stratton sig ret til at udskifte motoren i
denne serie med en motor med højere nomineret effekt.
Garanti
Briggs & Stratton Motorgaranti
Gældende fra januar 2017
Begrænset garanti
Briggs & Stratton garanterer, at man i løbet af garantiperioden angivet nedenfor vil reparere
eller udskifte enhver del, der er defekt i materiale eller håndværk eller begge dele, uden
beregning. Transportomkostninger i forbindelse med et produkt, som indleveres til reparation
eller udskiftning under denne garanti, afholdes af køberen. Denne garanti er gyldig inden
for tidsperioderne og underlagt nedenstående betingelser. Find den nærmeste autoriserede
serviceforhandler kortet over forhandlere BRIGGSandSTRATTON.COM i forbindelse
med service under garantien. Køberen skal kontakte den autoriserede serviceforhandler
og derefter stille produktet til rådighed for den autoriserede serviceforhandler med henblik
inspektion og afprøvning.
Der ydes ikke nogen anden udtrykkelig garanti. Underforståede garantier, inklusive
garantier for salgbarhed og egnethed til et bestemt formål, er begrænset til
garantiperioden, der er angivet nedenfor, eller i den udstrækning loven tillader.
Ansvar for hændelige skader eller følgeskader er udelukket, i det omfang lovgivningen
tillader udelukkelse. Visse stater eller lande tillader ikke begrænsninger på, hvor lang tid
en underforstået garanti varer, og visse stater eller lande tillader ikke udelukkelse eller
begrænsning af tilfældig skade eller følgeskade, ovenstående begrænsning og
udelukkelse er måske ikke gældende for dig. Denne garanti giver dig specifikke juridiske
rettigheder, og du kan endvidere have andre rettigheder, som kan variere fra land til land
4
.
Almindelige garantibestemmelser
1, 2, 3
Erhvervsmæssig
brug
Privat brugMærke / produktnavn
36 måneder36 månederVanguard™; kommerciel serie
12 måneder24 månederMotorer med Dura-Bore™-støbejernsboring
3 måneder24 månederAlle andre motorer
1
Dette er vores vilkår for standardgaranti, men der kan lejlighedsvist være ekstra
garantidækning, der ikke var fastslået tidspunktet for offentliggørelsen. Hvis du
ønsker en liste over gældende garantivilkår for din motor, til
BRIGGSandSTRATTON.com, eller kontakt din autoriserede Briggs & Stratton-
serviceforhandler.
2
Der er ikke garanti for motorer udstyr, der bruges til priming i stedet for et værktøj
eller til standbygeneratorer, der anvendes til kommercielle formål. Motorer, der
anvendes til konkurrencemæssig motorsport eller erhvervs- eller udlejningsbaner,
er ikke omfattet af garantien.
3
Vanguard installeret standbygeneratorer: 24 måneder ved privat brug. Der gives
ikke garanti ved erhvervsmæssig brug. Vanguard installeret hjælpekøretøjer: 24
måneder ved privat brug, 24 måneder ved erhvervsmæssig brug. Kommerciel serie
med fremstillingsdato før juli 2017, 24 måneder ved privat brug, 24 måneder ved
erhvervsmæssig brug.
4
I Australien - Vores produkter sælges med en garanti, der ikke kan bortfalde i
henhold til den australske forbrugerlovgivning. Du er berettiget til en erstatning eller
refundering i tilfælde af en væsentlig defekt eller til kompensation for ethvert
forudseeligt tab eller skade. Du er derudover berettiget til at dine varer repareret
eller erstattet, hvis varerne ikke lever op til kvaliteten, og manglen ikke er i forbindelse
med en væsentlig defekt. I forbindelse med service under garantien findes den
nærmeste autoriserede serviceforhandler kortet over forhandlere
BRIGGSandSTRATTON.COM, ved at ringe til 1300 274 447 eller ved at sende en
e-mail eller skrive til [email protected], Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, Moorebank, NSW , Australia, 2170.
Garantiperioden starter købsdatoen for den første almindelige eller erhvervsmæssige
bruger. "Privat brug" betyder brug i personlig beboelseshusholdning af en detailkunde.
"Erhvervsmæssig brug" betyder al anden form for brug, inklusive erhvervsmæssigt,
indkomstdannende eller lejebaseret formål. Når en motor har været anvendt
erhvervsmæssigt, skal den herefter anses for at være en motor til erhvervsbrug i henhold
til denne garanti.
Gem dit købsbevis. Hvis du ikke kan fremvise bevis for den oprindelige købsdato
det tidspunkt, hvor der bliver anmodet om garantiservice, vil produktets
produktionsdato blive brugt som grundlag for garantien. Det er ikke nødvendigt at
registrere sit produkt for at opnå garanti Briggs & Stratton produkter.
Om garantien
Denne garanti dækker alene motor-relaterede materiale- og/eller fremstillingsfejl og ikke
udskiftning eller tilbagebetaling for det redskab, hvorpå motoren måtte være monteret.
Rutinemæssig vedligeholdelse, optuninger, justeringer eller normal slitage dækkes ikke
under denne garanti. samme måde gælder denne garanti heller ikke, hvis motoren er
ændret eller modificeret, eller hvis motorens serienummer er ødelagt eller fjernet. Denne
garanti dækker ikke motorskade eller driftsproblemer som følge af:
1. Brug af dele, der ikke er originale dele fra Briggs & Stratton
2. Betjening af motoren med utilstrækkelig, forurenet eller forkert type olie
3. Brug af forurenet eller gammel olie, benzin med mere end 10 % etanol eller brug af
alternative brændstoffer som petroleumsvæske eller naturgas motorer, der ikke
oprindeligt er udviklet/fremstillet af Briggs & Stratton til at fungere med sådanne
brændstoffer
4. Snavs, der er trængt ind i motoren grund af utilstrækkelig vedligeholdelse af
luftrensesystemet eller genmontering
5. Stød mod et objekt med skærebladet i en roterende plæneklipper, løse eller forkert
installerede bladadaptere, rotorer eller andet udstyr koblet krumtapakslen eller
for høj V-remspænding
6. Tilhørende dele eller tilbehør som koblinger, transmissioner, udstyrskontroller osv.,
som ikke leveres af Briggs & Stratton
7. Overophedning grund af græsslåning, snavs og affald eller gnaverreder, der
tilstopper kølefinnerne eller svinghjulsområdet eller drift af motoren uden tilstrækkelig
ventilation
8. Overdreven vibration grund af for høj hastighed, løs motormontering, løse eller
ubalancerede skæreblade eller rotorer eller forkert kobling af udstyrskomponenter
krumtapakslen
9. Misbrug, mangel rutinevedligeholdelse, forsendelse, håndtering eller udstyrets
opbevaring lager eller forkert motorinstallation.
Servicegarantien er kun tilgængelig via autoriserede Briggs & Stratton-
serviceforhandlere. Find din nærmeste serviceforhandler vores forhandlerkort
BRIGGSandSTRATTON.COM, eller ved at ringe til 1-800-233-3723 (i USA).
80004537 (rev. C)
19
Not for
Reproduction
Copyright © Briggs & Stratton Corporation, Milwaukee, WI, USA. Alle Rechte vorbehalten.
Dieses Handbuch enthält Sicherheitshinweise, die Sie auf die Gefahren und Risiken beim
Betrieb von Motoren hinweisen und Ihnen helfen sollen, diese Gefahren zu vermeiden. Es
enthält außerdem Anweisungen zur richtigen Verwendung und Pflege des Motors. Da
Briggs & Stratton nicht genau wissen kann, welches Gerät von diesem Motor angetrieben
wird, ist es wichtig, dass Sie diese Anweisungen sowie die Anweisungen für das Gerät,
das von diesem Motor angetrieben wird, gründlich durchlesen. Bewahren Sie diese
Original-Bedienungsanleitung zum späteren Nachschlagen auf.
Hinweis:
Die Abbildungen und Illustrationen in dieser Anleitung dienen nur zur Orientierung
und können vom jeweiligen Modell abweichen. Wenden Sie sich bei Fragen an Ihren
Händler.
Um in Zukunft Ersatzteile oder technische Unterstützung für Ihren Motor zu erhalten, sollten
Sie sich hier die Modell-, Typen- und Codenummer Ihres Motors sowie das Kaufdatum
notieren. Diese Nummern befinden sich an Ihrem Motor (siehe Abschnitt
Funktionen und
Bedienungselemente
).
Kaufdatum
Motormodell Typ Trim
Motorseriennummer
An einigen Motoren befindet sich ein 2D-
Barcode. Wenn der Code mit einem 2D-Gerät
gescannt wird, wird unsere Website
aufgerufen, auf der Sie Informationen zu
diesem Produkt bekommen können. Es gelten
entsprechende Datenraten. In einigen
Ländern ist möglicherweise keine Online-
Unterstützung verfügbar.
Recyclinginformation
Das gesamte Verpackungsmaterial, Altöl und Batterien müssen
in Übereinstimmung mit staatlichen Vorschriften recycelt
werden.
Bedienersicherheit
Sicherheitswarnsymbol und Signalwörter
Das Sicherheitswarnsymbol kennzeichnet Sicherheitsinformationen zu Risiken, die
zu Verletzungen führen können. Ein Signalwort (GEFAHR, WARNUNG oder VORSICHT)
wird zusammen mit dem Warnsymbol verwendet, um den Grad der Gefahr und die Schwere
der möglichen Verletzung anzugeben. Darüber hinaus kann ein Gefahrensymbol zur
Kennzeichnung der Art der Gefahr benutzt werden.
GEFAHR weist auf eine Gefahr hin, die zum Tod oder zu schweren Verletzungen
führt, wenn sie nicht vermieden wird.
WARNUNG weist auf eine Gefahr hin, die zum Tod oder zu schweren Verletzungen
führen könnte, wenn sie nicht vermieden wird.
VORSICHT weist auf eine Gefahr hin, die zu leichten bis mittelschweren
Verletzungen führen könnte, wenn sie nicht vermieden wird.
HINWEIS
weist auf eine Situation hin, in der das Produkt beschädigt werden könnte.
Gefahrensymbole und ihre Bedeutung
BedeutungSymbolBedeutungSymbol
Lesen Sie sich die
Bedienungsanleitung gründlich
durch, bevor Sie das Gerät
einsetzen oder warten.
Sicherheitsinformationen zu
Gefahren, die zu
Verletzungen führen
können.
BedeutungSymbolBedeutungSymbol
ExplosionsgefahrFeuergefahr
Gefährdung durch giftige
Dämpfe
Stromschlaggefahr
Lärmgefährdung bei längerem
Einsatz wird ein Gehörschutz
empfohlen.
Gefährdung durch heiße
Oberflächen
ExplosionsgefahrGefährdung durch
hochgeschleuderte
Gegenstände
Augenschutz tragen.
RückschlaggefahrErfrierungsgefahr
Gefährdung durch ChemikalienAmputationsgefahr
bewegliche Teile
ÄtzendGefährdung durch Wärme
Sicherheitsvorkehrungen
WARNUNG
Gemäß den Erkenntnissen des Staates Kalifornien enthalten bestimmte Bestandteile
und Zubehörteile des Produkts Chemikalien, die Krebs oder Geburtsfehler verursachen
oder die Fortpflanzungsfähigkeit beeinträchtigen können. Waschen Sie sich nach
Umgang mit solchen Teilen die Hände.
WARNUNG
Gemäß den Erkenntnissen des Staates Kalifornien enthalten die Motorabgase dieses
Produkts Chemikalien, die Krebs oder Geburtsfehler verursachen oder die
Fortpflanzungsfähigkeit beeinträchtigen können.
WARNUNG
Motoren von Briggs & Stratton sind nicht konzipiert und nicht geeignet für den Antrieb
von Fun-Karts, Go-Karts, Freizeitfahrzeugen für Kinder, Geländefahrzeugen für den
Motorsport, Motorrädern, Luftkissenfahrzeugen, Luftfahrzeugen oder Fahrzeugen für
den Rennsport, wenn dies nicht von Briggs & Stratton genehmigt ist. Informationen
über Rennsportprodukte finden Sie auf www.briggsracing.com. Zum Einsatz mit
Nutzfahrzeug-ATVs und Side-by-side-ATVs wenden Sie sich bitte an das Briggs &
Stratton Engine Application Center, 1-866-927-3349. Unvorschriftsmäßige
Motoranwendung kann zu schweren Verletzungen oder zum Tod führen.
WARNUNG
Kraftstoff und Kraftstoffdämpfe sind extrem entzündlich und es besteht
Explosionsgefahr.
Brand oder Explosionen können zu schweren Verbrennungen oder Tod führen.
Bei der Betankung
Stellen Sie den Motor ab und lassen Sie ihn mindestens 2 Minuten abkühlen, bevor
Sie die Verschlusskappe entfernen.
Füllen Sie den Tank im Freien oder an einem gut belüfteten Ort auf.
20 BRIGGSandSTRATTON.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96