Sony XR-1300R Användarmanual

varumärke: Sony

Modell: XR-1300R

Kategori: Mottagare för bilmedia

Typ: Användarmanual

 2000 Sony Corporation

FM/MW/LW

Cassette

Car Stereo

3-044-698-11 (1)

Operating Instructions

Manual de instrucciones

Bruksanvisning

Manual de instruções

XR-1300R

For installation and connections, see the supplied installation/connections

manual.

Para obtener información sobre la instalación y las conexiones, consulte el manual

de instalación/conexiones suministrado.

Vi hänvisar till det medföljande häftet angående montering/anslutningar.

Para a instalação e as ligações, consulte o manual de instalação/ligações

fornecido.

Thank you for purchasing this Sony Cassette

Player.

Welcome ! Precautions

• If your car was parked in direct sunlight

resulting in a considerable rise in

temperature inside the car, allow the unit to

cool off before operating it.

• If no power is being supplied to the unit,

check the connections first. If everything is in

order, check the fuse.

• If no sound comes from the speakers of a

two-speaker system, set the fader control to

the centre position.

• When a tape is played back for a long period,

the cassette may become warm because of

the built-in power amplifier. However, this is

not a sign of malfunction.

If you have any questions or problems

concerning your unit that are not covered in

this manual, please consult your nearest Sony

dealer.

To maintain high quality sound

If you have drink holders near your audio

equipment, be careful not to splash juice or

other soft drinks onto the car audio. Sugary

residues on this unit or cassette tapes may

contaminate the playback heads, reduce the

sound quality, or prevent sound reproduction

altogether.

Cassette cleaning kits cannot remove sugar

from the tape heads.

Notes on Cassettes

Cassette care

• Do not touch the tape surface of a cassette, as

any dirt or dust will contaminate the heads.

• Keep cassettes away from equipment with

built-in magnets such as speakers and

amplifiers, as erasure or distortion on the

recorded tape could occur.

• Do not expose cassettes to direct sunlight,

extremely cold temperatures, or moisture.

• Slack in the tape may cause the tape to be

caught in the machine. Before you insert the

tape, use a pencil or similar object to turn the

reel and take up any slack.

• Distorted cassettes and loose labels can cause

problems when inserting or ejecting tapes.

Remove or replace loose labels.

• The sound may become distorted while

playing the cassette. The cassette player head

should be cleaned after each 50 hours of use.

Slack

Cassettes longer than 90 minutes

The use of cassettes longer than 90 minutes is

not recommended except for long continuous

play. The tape used for these cassettes is very

thin and tends to stretch easily. Frequent

playing and stopping of these tapes may cause

them to become entangled in the cassette deck

mechanism.

Table of Contents

Location of controls ................................................. 5

Getting Started

Resetting the unit ................................................ 6

Detaching the front panel .................................. 6

How to use the menu ......................................... 6

Setting the clock .................................................. 7

Cassette Player

Listening to a tape ............................................... 7

Radio Reception during Fast-forwarding or

Rewinding of a Tape

— ATA (Automatic Tuner Activation) ........ 8

Radio

Memorizing stations automatically

— Best Tuning Memory (BTM) .................... 8

Memorizing only the desired stations ............. 9

Receiving the memorized stations.................... 9

RDS

Overview of the RDS function ........................ 10

Displaying the station name ............................ 10

Retuning the same programme automatically

— Alternative Frequencies (AF) ................ 10

Listening to traffic announcements ................ 12

Presetting the RDS stations with the AF and

TA data .......................................................... 12

Locating a station by programme type .......... 13

Setting the clock automatically ....................... 14

Other Functions

Adjusting the sound characteristics ............... 15

Changing the sound and display settings ..... 15

Boosting the bass sound

— D-bass ....................................................... 16

Additional Information

Maintenance ....................................................... 16

Dismounting the unit ....................................... 17

Specifications ..................................................... 18

Troubleshooting guide ..................................... 19

Location of controls

Refer to the pages listed for details.

1 MENU button

7, 8, 9, 11, 13, 14, 15

2 Volume control dial

3 TUNER button 8, 9, 12

4 PRST +/– (cursor up/down) buttons

7, 8, 9, 11, 13, 14, 15

During radio reception:

Preset stations select 8, 9

5 DSPL/PTY (display mode change/

programme type) button 14

6 MODE button

During radio reception:

BAND select 8, 9

7 Z (eject) button 7

8 Display window

9 m/M (fast winding)/DIR (tape

transport direction change) buttons 7

q; D-BASS button 16

qa TA button 12, 13

qs SOUND button 15

qd RELEASE (front panel release) button

6, 17

qf SEEK –/+ (cursor left/right) buttons

7, 8, 9, 11, 13, 14, 15

seek 9

qg Reset button (located on the front side

of the unit behind the front panel) 6

qh ENTER button 7, 8, 9, 11, 13, 14, 15

qj Preset number buttons 9, 11

qk OFF button* 6

ql AF button 10, 11, 13

* Warning when installing in a car

without ACC (accessory) position on

the ignition key switch

Be sure to press (OFF) on the unit for two

seconds to turn off the clock display after

turning off the engine.

When you press (OFF) momentarily, the

clock display does not turn off and this

causes battery wear.

XR-1300R

–

MODE

OFF

DIR

D-BASS

ENTER

SOUND

RELEASE

1 2 3 4 56

TUNER

DSPL

PTY

TUNER

Attaching the front panel

Attach part A of the front panel to part B of

the unit as illustrated and push the left side

into position until it clicks.

Notes

• Be sure not to attach the front panel upside

down.

• Do not press the front panel too hard against the

unit when attaching it.

• Do not press too hard or put excessive pressure

on the display window of the front panel.

• Do not expose the front panel to direct sunlight

or heat sources such as hot air ducts, and do not

leave it in a humid place. Never leave it on the

dashboard of a car parked in direct sunlight or

where there may be a considerable rise in

temperature.

Caution alarm

If you turn the car ignition off without

removing the front panel, the caution alarm

will beep for a few seconds.

If you connect an optional power amplifier and

do not use the built-in amplifier, the beep

sound will be deactivated.

How to use the menu

This unit is operated by selecting items from a

menu.

To select, first enter the menu mode and

choose up/down (+/– of (PRST)), or choose

left/right (–/+ of (SEEK)).

(PRST)

(+) : To select upwards

(–) : To select downwards

Getting Started

Resetting the unit

Before operating the unit for the first time or

after replacing the car battery, you must reset

the unit.

Remove the front panel and press the reset

button with a pointed object, such as a

ballpoint pen.

Note

Pressing the reset button will erase the clock

setting and some memorized functions.

Detaching the front panel

You can detach the front panel of this unit to

protect the unit from being stolen.

1 Press (OFF).

2 Press (RELEASE), then slide the front

panel a little to the left, and pull it off

towards you.

Notes

• Be sure not to drop the panel when detaching it

from the unit.

• If you detach the panel while the unit is still

turned on, the power will turn off automatically

to prevent the speakers from being damaged.

• When carrying the front panel with you, use the

supplied front panel case.

Reset button

(OFF)

(RELEASE)

Cassette Player

Listening to a tape

Insert a cassette.

Playback starts automatically.

The side facing up is played.

The side facing down is played.

Tip

To change the tape‘s playback direction, press m

and M.

To stop playback and eject the

cassette

Press Z.

Fast-winding the tape

During playback, press m or M.

* The < > indicator will flash while fast-winding

the tape.

To start playback during fast-forwarding or

rewinding, press the other fast-winding button

partially until the locked button is released.

(SEEK)

Setting the clock

The clock uses a 24-hour digital indication.

Example: To set the clock to 10:08

1 Press (MENU), then press either side of

(PRST) repeatedly until “CLOCK”

appears.

1 Press (ENTER).

The hour indication flashes.

2 Press either side of (PRST) to set the

hour.

3 Press + side of (SEEK).

The minute indication flashes.

4 Press either side of (PRST) to set the

minute.

2 Press (ENTER).

The clock starts.

After the clock setting is complete, the

display returns to normal playback mode.

To rewind

Direction

indicator*

FWD

REV

To advance

(–) : To select

leftwards

(+) : To select

rightwards

TUNER

Radio

Memorizing stations

automatically

— Best Tuning Memory (BTM)

The unit selects the stations with the strongest

signals and memorizes them in the order of

their frequencies. You can store up to 6 stations

on each band (FM1, FM2, FM3, MW, and LW).

Caution

When tuning in stations while driving, use

Best Tuning Memory to prevent accidents.

1 Press (TUNER).

The tuner is turned on.

2 Press (MODE) repeatedly to select the

band.

Each time you press (MODE), the band

changes as follows:

B FM1 B FM2 B FM3 B MW B LW

3 Press (MENU), then press either side of

(PRST) repeatedly until “BTM” appears.

4 Press (ENTER).

The unit stores stations in the order of their

frequencies on the number buttons.

A beep sounds when the setting is stored.

Notes

• The unit does not store stations with weak

signals. If only a few stations can be received,

some number buttons will retain their former

setting.

• When a number is indicated in the display, the

unit starts storing stations from the one currently

displayed.

Radio Reception during

Fast-forwarding or

Rewinding of a Tape

— ATA (Automatic Tuner Activation)

When fast-forwarding or rewinding with the

m or M button, the tuner will turn on

automatically.

1 During playback, press (MENU).

2 Press either side of (PRST) repeatedly

until “ATA” appears.

3 Press + side of (SEEK) to select “ON.”

Play mode starts.

4 Press (ENTER).

To return to normal playback mode, select

“OFF” in step 3 above.

Memorizing only the

desired stations

You can preset up to 18 FM stations (6 each for

FM1, 2, and 3), up to 6 MW stations, and up to

6 LW stations in the order of your choice.

1 Press (TUNER).

The tuner is turned on.

2 Press (MODE) repeatedly to select the

band.

3 Press either side of (SEEK) to tune in the

station that you want to store on the

number button.

4 Press and hold the desired number

button ((1) to (6)) until “MEM” appears.

The number button indication appears in

the display.

Note

If you try to store another station on the same

number button, the previously stored station will

be erased.

Receiving the memorized

stations

1 Press (TUNER).

The tuner is turned on.

2 Press (MODE) repeatedly to select the

band.

3 Press the number button ((1) to (6)) on

which the desired station is stored.

Tip

Press either side of (PRST) to receive the stations

in the order they are stored in the memory (Preset

Search Function).

If you cannot tune in a preset

station

Press either side of (SEEK) to search for

the station (automatic tuning).

Scanning stops when the unit receives a

station. Press either side of (SEEK)

repeatedly until the desired station is

received.

Note

If the automatic tuning stops too frequently, press

(MENU), then press either side of (PRST)

repeatedly until “LOCAL” (local seek mode) is

displayed. Then press + side of (SEEK) to select

“LOCAL-ON.” Press (ENTER).

Only the stations with relatively strong signals will

be tuned in.

Tip

If you know the frequency of the station you want

to listen to, press and hold either side of (SEEK)

until the desired frequency appears (manual

tuning).

If FM stereo reception is poor

— Monaural Mode

1 During radio reception, press (MENU),

then press either side of (PRST)

repeatedly until “MONO” appears.

2 Press + side of (SEEK) until “MONO-ON“

appears.

The sound improves, but becomes

monaural (“ST” disappears).

3 Press (ENTER).

To return to normal mode, select “MONO-

OFF” in step 2 above.

Retuning the same

programme automatically

— Alternative Frequencies (AF)

The Alternative Frequencies (AF) function

automatically selects and retunes the station

with the strongest signal in a network. By

using this function, you can continuously

listen to the same programme during a long-

distance drive without having to retune the

station manually.

1 Select an FM station (page 9).

2 Press (AF) repeatedly until “AF-ON”

appears.

The unit starts searching for an alternative

station with a stronger signal in the same

network.

Note

When there is no alternative station in the area

and you do not need to search for an alternative

station, turn the AF function off by pressing (AF)

repeatedly until “AF-OFF” appears.

102.5MHz

96.0MHz

98.5MHz

Frequencies change automatically.

Station

RDS

Overview of the RDS

function

Radio Data System (RDS) is a broadcasting

service that allows FM stations to send

additional digital information along with the

regular radio programme signal. Your car

stereo offers you a variety of services. Here are

just a few: retuning the same programme

automatically, listening to traffic

announcements, and locating a station by

programme type.

Notes

• Depending on the country or region, not all of

the RDS functions are available.

• RDS may not work properly if the signal strength

is weak or if the station you are tuned to is not

transmitting RDS data.

Displaying the station

name

The name of the current station lights up in the

display.

Select an FM station (page 9).

When you tune in an FM station that

transmits RDS data, the station name

appears in the display.

Note

The “*” indication means that an RDS station is

being received.

Local link function

(United Kingdom only)

The Local Link function lets you select other

local stations in the area, even if they are not

stored on your number buttons.

1 Press a number button that has a local

station stored on it.

2 Within five seconds, press the number

button of the local station again.

3 Repeat this procedure until the desired

local station is received.

Changing the display item

Each time you press (AF), the item changes as

follows:

AF-ON y AF-OFF

Notes

• When “NO AF” and the station name flash

alternately, it means that the unit cannot find an

alternative station in the network.

• If the station name starts flashing after selecting

a station with the AF function on, this indicates

that no alternative frequency is available. Press

either side of (SEEK) while the station name is

flashing (within eight seconds). The unit starts

searching for another frequency with the same PI

(Programme Identification) data (“PI SEEK”

appears and no sound is heard). If the unit

cannot find another frequency, “NO PI” appears,

and the unit returns to the previously selected

frequency.

Listening to a regional programme

The “REG-ON” (regional on) function lets you

stay tuned to a regional programme without

being switched to another regional station.

(Note that you must turn the AF function on.)

The unit is factory preset to “REG-ON,” but if

you want to turn off the function, do the

following.

1 During radio reception, press (MENU),

then press either side of (PRST)

repeatedly until “REG” appears.

2 Press + side of (SEEK) until “REG-OFF”

appears.

3 Press (ENTER).

Note that selecting “REG-OFF” might cause

the unit to switch to another regional

station within the same network.

To return to regional on, select “REG-ON” in

step 2 above.

Note

This function does not work in the United

Kingdom and in some other areas.

Presetting the volume of traffic

announcements

You can preset the volume level of the traffic

announcements beforehand so you won’t

miss the announcement. When a traffic

announcement starts, the volume will be

automatically adjusted to the preset level.

1 Select the desired volume level.

2 Press (TA) for two seconds.

“TA” appears and the setting is stored.

Receiving emergency

announcements

If an emergency announcement comes in while

you are listening to the radio, the programme

will automatically switch to it. If you are

listening to a source other than the radio, the

emergency announcements will be heard if

you set AF or TA to on. The unit will then

automatically switch to these announcements

no matter which source you are listening to at

the time.

Presetting the RDS

stations with the AF and

TA data

When you preset RDS stations, the unit stores

each station’s data as well as its frequency, so

you don’t have to turn on the AF or TA

function every time you tune in the preset

station. You can select a different setting (AF,

TA, or both) for individual preset stations, or

the same setting for all preset stations.

Listening to traffic

announcements

The Traffic Announcement (TA) and Traffic

Programme (TP) data let you automatically

tune in an FM station that is broadcasting

traffic announcements even if you are listening

to other programme sources.

Press (TA) repeatedly until “TA-ON”

appears.

The unit starts searching for traffic

information stations. “TP” appears in the

display when the unit finds a station

broadcasting traffic announcements.

When the traffic announcement starts,

“TA” flashes. The flashing stops when the

traffic announcement is over.

Tip

If the traffic announcement starts while you are

listening to another programme source, the unit

automatically switches to the announcement and

goes back to the original source when the

announcement is over.

Notes

•

“NO TP” flashes for five seconds if the received

station does not broadcast traffic announcements.

Then, the unit starts searching for a station that

broadcasts it.

• When “EON” appears with “TP” in the display,

the current station makes use of broadcast traffic

announcements by other stations in the same

network.

To cancel the current traffic

announcement

Press (TA) or (TUNER).

To cancel all traffic announcements, turn off

the function by pressing (TA) until

“TA-OFF” appears.

Presetting the same setting for all

preset stations

1 Select an FM band (page 9).

2 Press (AF) or/and (TA) to select “AF-ON”

or/and “TA-ON.”

Note that selecting “AF-OFF” or “TA-OFF”

stores not only RDS stations, but also non-

RDS stations.

3 Press (MENU), then press either side of

(PRST) repeatedly until “BTM” appears.

4 Press + side of (SEEK) until “BTM”

flashes.

5 Press (ENTER).

Presetting different settings for

each preset station

1 Select an FM band, and tune in the

desired station.

2 Press (AF) or/and (TA) to select “AF-ON”

or/and “TA-ON.”

3 Press the desired number button and

hold until “MEM” appears.

Repeat from step 1 to preset other stations.

Tip

If you want to change the preset AF and/or TA

setting after you tune in the preset station, you

can do so by turning the AF or TA function on or

off.

Locating a station by

programme type

You can locate the station you want by

selecting one of the programme types shown

below.

Programme types Display

News NEWS

Current Affairs AFFAIRS

Information INFO

Sports SPORT

Education EDUCATE

Drama DRAMA

Culture CULTURE

Science SCIENCE

Varied VARIED

Popular Music POP M

Rock Music ROCK M

Easy Listening EASY M

Light Classical LIGHT M

Classical CLASSICS

Other Music Type OTHER M

Weather WEATHER

Finance FINANCE

Children’s Programmes CHILDREN

Social Affairs SOCIAL A

Religion RELIGION

Phone In PHONE IN

Travel TRAVEL

Leisure LEISURE

Jazz Music JAZZ

Country Music COUNTRY

National Music NATION M

Oldies Music OLDIES

Folk Music FOLK M

Documentary DOCUMENT

Not specified NONE

Note

You cannot use this function in some countries

where no PTY (Programme Type selection) data is

available.

1 Press (DSPL/PTY) during FM reception

until “PTY” appears.

The current programme type name appears

if the station is transmitting the PTY data.

“- - - - -” appears if the received station is

not an RDS station, or if the RDS data has

not been received.

If the TA function is ON, the unit starts

searching for the next station.

2 Press (PRST) repeatedly until the desired

programme type appears.

The programme types appear in the order

shown in the above table. Note that you

cannot select “NONE” (Not specified) for

searching.

3 Press (ENTER) repeatedly until the

desired station is received.

The unit starts searching for a station

broadcasting the selected programme type.

When the unit finds the programme, the

programme type appears again for five

seconds.

“NO” and the programme type appear

alternately for five seconds if the unit

cannot find the programme type. It then

returns to the previously selected station.

Setting the clock

automatically

The CT (Clock Time) data from the RDS

transmission sets the clock automatically.

1 During radio reception, press (MENU),

then press either side of (PRST)

repeatedly until “CT” appears.

2 Press + side of (SEEK) repeatedly until

“CT-ON” appears.

The clock is set.

3 Press (ENTER) to return to the normal

display.

To cancel the CT function

Select “CT-OFF” in step 2 above.

Notes

• The CT function may not work even though an

RDS station is being received.

• There might be a difference between the time

set by the CT function and the actual time.

Changing the sound and

display settings

The following items can be set:

•CLOCK (page 7).

•CT (Clock Time) (page 14).

•BEEP – to turn the beep sound on or off.

•D.INFO (Dual Information) to display the

clock and the play mode at the same time

(ON) or to display the information

alternately (OFF).

•M.DSPL (Motion Display) – to turn the

motion display on or off.

1 Press (MENU).

2 Press either side of (PRST) repeatedly

until the desired item appears.

Each time you press (–) side of (PRST), the

item changes as follows:

CLOCK t CT t BEEP t D.INFO t M.DSPL

3 Press (+) side of (SEEK) to select the

desired setting (Example: ON or OFF).

4 Press (ENTER).

After the mode setting is complete, the

display returns to normal playback mode.

Other Functions

Adjusting the sound

characteristics

You can adjust the bass, treble, balance, and

fader.

You can store the bass and treble levels

independently for each source.

1 Select the item you want to adjust by

pressing (SOUND) repeatedly.

BAS (bass) t TRE (treble) t

BAL (left-right) t FAD (front-rear)

2 Adjust the selected item by pressing

either side of (SEEK).

Adjust within three seconds after selecting

the item.

0dB

D.BASS-3

D.BASS-2

D.BASS-1

D.BASS-3

D.BASS-2

D.BASS-1

Boosting the bass sound

— D-bass

You can enjoy a clear and powerful bass

sound. The D-bass function boosts the low

frequency signal and high frequency signal

with a sharper curve than conventional bass

boost.

You can hear the bass line more clearly even

while the vocal volume remains the same. You

can emphasize and adjust the bass sound

easily with the D-BASS control.

Adjusting the bass curve

Press (D-BASS) repeatedly to select the

desired bass curve.

As the D-BASS number increases so does

the effect.

D.BASS-1 t D.BASS-2 t D.BASS-3 t

D.BASS-OFF

Note

The bass sound may distort at same volume. If the

bass sound distorts, select less effective bass curve.

Level

Frequency (Hz)

Fuse (10 A)

Additional

Information

Maintenance

Fuse replacement

When replacing the fuse, be sure to use one

matching the amperage rating stated on the

original fuse. If the fuse blows, check the

power connection and replace the fuse. If the

fuse blows again after replacement, there may

be an internal malfunction. In such a case,

consult your nearest Sony dealer.

Warning

Never use a fuse with an amperage rating

exceeding the one supplied with the unit as

this could damage the unit.

Release key (supplied)

Dismounting the unit

Cleaning the connectors

The unit may not function properly if the

connectors between the unit and the front

panel are not clean. In order to prevent this,

open the front panel by pressing (RELEASE),

then detach it and clean the connectors with a

cotton swab dipped in alcohol. Do not apply

too much force. Otherwise, the connectors may

be damaged.

Main unit

Back of the front panel

Notes

• For safety, turn off the engine before cleaning

the connectors and remove the key from the

ignition switch.

• Never touch the connectors directly with your

fingers or any metal device.

Specifications

Cassette player section

Tape track 4-track 2-channel stereo

Wow and flutter 0.13 % (WRMS)

Frequency response 30 – 15,000 Hz

Signal-to-noise ratio 55 dB

Tuner section

Tuning range 87.5 – 108.0 MHz

Aerial terminal External aerial connector

Intermediate frequency 10.7 MHz

Usable sensitivity 9 dBf

Selectivity 75 dB at 400 kHz

Signal-to-noise ratio 65 dB (stereo),

68 dB (mono)

Harmonic distortion at 1 kHz

0.7 % (stereo),

0.4 % (mono)

Separation 35 dB at 1 kHz

Frequency response 30 – 15,000 Hz

MW/LW

Tuning range MW: 531 – 1,602 kHz

LW: 153 – 279 kHz

Aerial terminal External aerial connector

Intermediate frequency 10.7 MHz/450 kHz

Sensitivity MW: 30 µV

LW: 50 µV

Power amplifier section

Outputs Speaker outputs

(sure seal connectors)

Speaker impedance 4 – 8 ohms

Maximum power output 45 W × 4 (at 4 ohms)

General

Outputs Power aerial relay control

lead

Power amplifier control

lead

Tone controls Bass ±8 dB at 100 Hz

Treble ±8 dB at 10 kHz

Power requirements 12 V DC car battery

(negative earth)

Dimensions Approx. 188 × 58 × 182 mm

(w/h/d)

Mounting dimensions Approx. 182 × 53 × 163 mm

(w/h/d)

Mass Approx. 1.2 kg

Supplied accessories Parts for installation and

connections (1 set)

Front panel case (1)

Design and specifications are subject to change

without notice.

Troubleshooting guide

The following checklist will help you remedy the problems you may encounter with your unit.

Before going through the checklist below, check the connections and operating procedures.

General

Tape playback

Problem

The sound is distorted.

Cause/Solution

The tape head is contaminated.

t Clean the head with a commercially available dry-type

cleaning cassette.

Radio reception

Problem

Preset tuning is not possible.

Automatic tuning is not

possible.

The stations cannot be

received.

The sound is hampered by

noises.

The “ST” indication flashes.

Cause/Solution

• Memorize the correct frequency.

• The broadcast signal is too weak.

The broadcast signal is too weak.

t Use manual tuning.

Connect an power aerial control lead (blue) or accessory power

supply lead (red) to the power supply lead of a car’s aerial

booster. (When your car has built-in FM/MW/LW aerial in the

rear/side glass only.)

•Tune in the frequency accurately.

•The broadcast signal is too weak.

t Set to MONO mode (page 9).

Problem

No sound.

The contents of the memory

have been erased.

Indications do not appear

in the display.

Cause/Solution

•Set the fader control to the centre position for two-speaker

systems.

•Rotate the dial clockwise to adjust the volume.

• The power cord or battery has been disconnected.

• The reset button was pressed.

t Store again into the memory.

Remove the front panel and clean the connectors. See

“Cleaning the connectors” (page 17) for details.

Continued to next page t

RDS

Problem

The SEEK starts after a few

seconds of listening.

No traffic announcements.

PTY displays “NONE.”

Cause/Solution

The station is non-TP or has a weak signal.

t Press (AF) or (TA) repeatedly until “AF-OFF” or

“TA-OFF” appears.

•Activate “TA.”

•The station does not broadcast any traffic announcements

despite being TP.

t Tune to another station.

The station does not specify the programme type.

Sidan laddas ...

Sony XR-1300R Användarmanual

varumärke: Sony

Modell: XR-1300R

Kategori: Mottagare för bilmedia

Typ: Användarmanual

Ladda ner pdf

Rapportera

på andra språk

español: Sony XR-1300R Manual de usuario
português: Sony XR-1300R Manual do usuário
English: Sony XR-1300R User manual

Sony XR-1300R Användarmanual

Sony XR-1300R Användarmanual

på andra språk

Relaterade papper