Husqvarna 115iL Cordless Grass Trimmer Användarmanual

115iL

EN Operator's manual 2-21

SV Bruksanvisning 22-40

DA Brugsanvisning 41-59

DE Bedienungsanweisung 60-80

NO Bruksanvisning 81-98

FI Käyttöohje 99-117

ES Manual de usuario 118-137

FR Manuel d'utilisation 138-157

IT Manuale dell'operatore 158-177

NL Gebruiksaanwĳzing 178-197

PT Manual do utilizador 198-217

Contents

Introduction..................................................................... 2

Safety..............................................................................4

Assembly...................................................................... 11

Operation...................................................................... 12

Maintenance................................................................. 15

Troubleshooting............................................................ 16

Transportation, storage and disposal........................... 17

Technical data.............................................................. 17

Accessories.................................................................. 19

Declaration of Conformity............................................. 20

Introduction

Product description

Husqvarna 115iL is a battery grass trimmer with an

electrical motor.

Work is constantly in progress to increase your safety

and efficiency during operation. Speak to your servicing

dealer for more information.

Intended use

The product is used with a trimmer head to cut grass.

Do not use the product for other tasks than grass

trimming and grass clearing.

Note: National regulations can set limit to the

operation of the product.

Product overview

4

10

3

2

22

1

20

17

16

21

9

7

6

8

1

5

11

13 12

19 18

15 14

24

13

23

1. Trimmer head 2. Cutting attachment guard

2782 - 013 - 21.09.2022

3. Shaft

4. Shaft adjustment (telescope)

5. Loop handle

6. Handle adjustment

7. Keypad

8. Power trigger lockout

9. Power trigger

10. Operator's manual

11. Power cord

12. Battery charger QC80

13. Power on and warning indicator

14. SavE button

15. Start/stop button

16. Battery

17. Battery release buttons

18. Battery indicator button

19. Battery status

20. Warning indicator

21. Hex key

22. Plant guard

23. Connector

24. Battery charger 40-C80

Symbols on the product

WARNING: This product can be

dangerous and cause serious injury or

death to the operator or others. Be careful

and use the product correctly. Read the

operator's manual carefully and make

sure that you understand the instructions

before you use the product.

Use the approved hearing protection and

eye protection.

Maximum speed of the output shaft.

Keep bystanders away.

The product agrees with the applicable

EC directives.

This product conforms to the applicable

UK regulations.

Use approved protective gloves.

Use heavy-duty slip-resistant boots.

The product or package cannot be

disposed as domestic waste. Recycle it

at a recycling station for electrical and

electronic equipment (applies to Europe

only).

Watch out for thrown objects and

ricochets.

Only use a flexible cutting attachment. Do

not use metal cutting attachments.

Do not expose to rain.

Direct current.

Noise emission to the environment label

as per EU (also including New South

Wales legislation) and UK directives

and regulations. The guaranteed sound

power level of the product is specified in

Technical data on page 17

and on the

label.

yyyywwxxxxx The rating plate shows the

serial number. yyyy is the

production year, ww is the

production week.

782 - 013 - 21.09.2022 3

Symbols on the battery and/or on the

battery charger

Recycle this product at a recy-

cling station for electrical and

electronic equipment. (Applies

to Europe only)

Fail-safe transformer.

Use and keep the battery charger indoors

only.

Double insulation.

Product liability

As referred to in the product liability laws, we are not

liable for damages that our product causes if:

• the product is incorrectly repaired.

• the product is repaired with parts that are not

from the manufacturer or not approved by the

manufacturer.

• the product has an accessory that is not from the

manufacturer or not approved by the manufacturer.

• the product is not repaired at an approved service

center or by an approved authority.

Safety

Safety definitions

Warnings, cautions and notes are used to point out

specially important parts of the manual.

WARNING: Used if there is a risk of

injury or death for the operator or bystanders

if the instructions in the manual are not

obeyed.

CAUTION: Used if there is a risk of

damage to the product, other materials or

the adjacent area if the instructions in the

manual are not obeyed.

Note: Used to give more information that is necessary

in a given situation.

General power tool safety warnings

WARNING: Read all safety warnings

and all instructions. Failure to follow the

warnings and instructions may result in

electric shock, fire and/or serious injury.

Note: Save all warnings and instructions for future

reference. The term "power tool" in the warnings refers

to your mains-operated (corded) power tool or battery-

operated (cordless) power tool.

Check before starting

• Always remove the battery to prevent the product

being started by accident. Always remove the battery

before any maintenance on the product.

• Before using the product and after any impact,

check for signs of wear or damage and repair as

necessary.

• Inspect the working area. Remove all loose objects,

such as stones, broken glass, nails, steel wire, string

etc. that could be thrown out or become wrapped

around the cutter or cutter guard.

• Check the motor for dirt and cracks. Clean off grass

and leaves from the motor using a brush. Gloves

should be worn when necessary.

• Check that the trimmer head is completely attached

to the trimmer.

• Check that the product is in perfect working order.

Check that all nuts and screws are tight.

• Check that the trimmer head and trimmer guard

are not damaged or cracked. Replace the trimmer

head or trimmer guard if they have been exposed

to impact or are cracked. Always use the

recommended guard for the cutting attachment you

are using. See chapter on Technical data.

• The product operator must ensure that no people or

animals come closer than 15 meters while working.

When several operators are working in the same

area the safety distance should be at least 15

meters.

• Carry out an overall inspection of the product before

use. See the maintenance schedule.

• National or local regulations may regulate the use.

Comply to given regulations.

Work area safety

•Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

•Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

4782 - 013 - 21.09.2022

•Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose

control.

Electrical safety

•Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce

risk of electric shock.

•Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

•Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

•Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk

of electric shock.

•When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of

electric shock.

•If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of a RCD reduces the risk of

electric shock.

Personal safety

•Stay alert, monitor what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result

in serious personal injury.

•Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

•Prevent unintentional starting. Ensure the switch is

in the OFF-position before connecting to a power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch

on invites accidents.

•Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personal injury.

•Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

•Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

•If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

• The vibration emission during actual use of the

power tool can differ from the declared total value

depending on the ways in which the tool is used.

Operators should identify safety measures to protect

themselves that are based on an estimation of

exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it is

running idle in addition to the trigger).

Power tool use and care

•Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it

was designed.

•Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

•Disconnect the plug from the power source and/or

the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool

accidentally.

•Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

•Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool´s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

•Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

•Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

Battery tool use and care

•Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another battery pack.

•Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury and fire.

•When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

782 - 013 - 21.09.2022 5

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause

burns or a fire.

•Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, flush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from

the battery may cause irritations or burns.

•Do not use a BATTERY pack or tool that is

damaged or modified.Damaged or modified batteries

may exhibit unpredictable behavior resulting in fire,

EXPLOSION or risk of injury.

•Do not expose a BATTERY pack or tool to

fire or excessive temperature.Exposure to fire or

temperature above 130 ºC (265 ºF) may cause

explosion.

•Follow all charging instructions and do not charge

the BATTERY pack or tool outside the temperature

range specified in the instructions.Charging

improperly or at temperatures outside the specified

range may damage the BATTERY and increase the

risk of fire.

Service

•Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is

maintained.

•Never service damaged BATTERY packs. Service of

BATTERY packs should only be performed by the

manufacturer or authorized service providers.

Always use common sense

It is not possible to cover every conceivable situation

you can face. Always exercise care and use your

common sense. Avoid all situations which you consider

to be beyond your capability. If you still feel

uncertain about operating procedures after reading

these instructions, you should consult an expert before

continuing.

WARNING: Never allow children to use

or be in the vicinity of the machine. Since

the machine is easy to start, children may be

able to start it if they are not kept under full

surveillance. This can mean a risk of serious

personal injury. Therefore disconnect the

battery when the machine is not under close

supervision.

General safety instructions

WARNING: Read the warning

instructions that follow before you use the

product.

• Remove the battery to prevent the product from

being started by accident.

• This product is a dangerous tool if you are not

careful or if you use the product incorrectly. This

product can cause serious injury or death to the

operator or others.

• Do not use the product if it is changed from its initial

specification. Do not change a part of the product

without approval from the manufacturer. Only use

parts that are approved by the manufacturer.

Injury or death is a possible result of incorrect

maintenance.

• Do a check of the product before use. See,

Check

before starting on page 4

and

Before you operate

the product on page 12

. Do not use a defective

product. Do the safety checks, maintenance and

service instructions described in this manual.

• Children should be supervised to ensure that they

do not play with the product. Never allow children or

other persons not trained in the use of the product

and/or the battery to use or service it. Local laws

may regulate the age of the user.

• Keep the product in a locked area to prevent access

for children or persons that are not approved.

• Store the product out of reach of children.

• Under no circumstances may the design of the

product be modified without the permission of the

manufacturer. Always use original accessories. Non-

authorized modifications and/or accessories can

result in serious personal injury or the death of the

operator and others.

Note: National or Local laws can regulate the use.

Comply to given regulations.

Safety instructions for operation

WARNING: Read the warning

instructions that follow before you use the

product.

• If you encounter a situation where you are uncertain

how to proceed you should ask an expert. Contact

your dealer or your service workshop. Avoid all

usage which you consider to be beyond your

capability.

• Never use the product if you are fatigued, while

under the influence of alcohol or drugs, medication

or anything that could affect your vision, alertness,

coordination or judgment.

• Never use the product in bad weather, for instance

in fog, in rain, strong winds, intense cold, etc.

Extremely hot weather may cause overheating of the

product.

• Faulty cutting attachment can increase the risk of

accidents.

• Do not allow children to use or be in the vicinity

of the product. Since the product is easy to start,

children may be able to start it if they are not kept

under full surveillance. This can mean a risk of

6782 - 013 - 21.09.2022

serious personal injury. Disconnect the battery when

the product is not under close supervision.

• Ensure that no people or animals come closer than

15 metres while you work. When several operators

are working in the same area the safety distance

should be at least 15 metres. Otherwise there is

a risk of serious personal injury. Stop the product

immediately if anyone approaches. Never swing the

product around without first checking behind you to

make sure that no one is within the safety zone.

• Ensure that people, animals or other things can

not affect your control of the product or that they

do not come in contact with the cutting attachment

or loose objects that are thrown out by the cutting

attachment. However, do not use the product unless

you are able to call for help in the event of an

accident.

• Always inspect the working area. Remove all loose

objects such as stones, broken glass, nails, steel

wire, string, etcetera, that could be thrown out or

become wrapped around the cutting attachment.

• Make sure that you can move and stand safely.

Check the area around you for possible obstacles

(roots, rocks, branches, ditches, etcetera) in case

you have to move suddenly. Take great care when

you work on sloping ground.

• Keep a good balance and a firm foothold at all times.

Do not overreach.

• Deactivate the product before you move to another

area. Attach the transport guard when the product is

not in use.

• Never put the product down unless you have

deactivated it. Do not leave the product

unsupervised when it is switched on.

• Remove the battery before you pass the product to

another person.

• Make sure that no clothes or parts of the body

come in contact with the cutting attachment when

the product is activated. Keep the product below

waist level.

• If anything jams in the cutting attachment while

you operate the product, stop and deactivate the

product. Make sure that the cutting attachment stops

completely. Remove the battery before you clean,

inspect or repair the product and/or the cutting

equipment.

• Keep your hands and feet away from the cutting

attachment until it has stopped completely when the

product is deactivated.

• Watch out for stumps of branches that can be thrown

out when you cut. Do not cut to close to the ground

where stones and other objects can be thrown out.

• Watch out for thrown objects. Always wear

approved eye protection. Never lean over the cutting

attachment guard. Stones, rubbish, etc., can be

thrown up into the eyes which can cause blindness

or serious injury.

• Listen out for warning signals or shouts when

you wear hearing protection. Always remove your

hearing protection as soon as the product stops.

• Never work from a ladder, stool or any other raised

position that is not fully secured.

• If any unwanted vibrations occur, tap out new line to

give the line the correct length to stop the vibrations.

• Overexposure to vibration can lead to circulatory

damage or nerve damage in persons who have

poor circulation. Speak to your physician if you

experience symptoms of overexposure to vibration.

Such symptoms include numbness, loss of feeling,

tingling, pricking, pain, loss of strength, changes in

skin colour or condition. These symptoms usually

show in the fingers, hands or wrists.

• Always hold the product with both hands. Hold the

product on the right side of your body.

• Do not remove the cut material, or let other persons

remove cut material, while the product is on or

the cutting equipment rotates, as this can result in

serious injury.

• Always stop the product, remove the battery and

make sure that the cutting equipment does not rotate

before you remove material that is wound around the

blade shaft or caught between the guard and the

cutting attachment.

Personal protective equipment

WARNING: Read the warning

instructions that follow before you use the

product.

• Always use approved personal protective equipment

when you use the product. Personal protective

equipment cannot fully prevent injury but it

decreases the degree of injury if an accident does

occur. Let your dealer help you select the right

equipment.

• Use a protective helmet where there is a risk of

falling objects.

• Use approved hearing protection that provides

adequate noise reduction. Long-term exposure to

noise can result in permanent hearing impairment.

• Use approved eye protection. If you use a visor,

you must also use approved protective goggles.

Approved protective goggles must comply with the

ANSI Z87.1 standard in the USA or EN 166 in EU

countries.

• Use a visor for face protection. A visor is not enough

for protection of the eyes.

+

• Use gloves when necessary, for example when you

attach, examine or clean the cutting equipment.

782 - 013 - 21.09.2022 7

• Use sturdy non-slip boots.

• Use clothing made of a strong fabric. Always use

heavy, long pants and long sleeves. Do not use

loose clothing that can catch on twigs and branches.

Do not wear jewelry, short pants, sandals or go with

bare feet. Put your hair up safely above shoulder

level.

• Keep first aid equipment close at hand.

Safety devices on the product

WARNING: Read the warning

instructions that follow before you use the

product.

In this section the product’s safety features, its purpose

and how checks and maintenance should be carried

out to ensure that it operates correctly. See instructions

under the heading

Introduction on page 2

to find where

these parts are located on your product.

The life span of the product can be reduced and the risk

of accidents can increase if product maintenance is not

carried out correctly and if service and/or repairs are not

carried out professionally. If you need further information

please contact your nearest servicing dealer.

WARNING: Never use a product with

defective safety components. The product's

safety equipment must be inspected and

maintained as described in this section.

If your product fails any of these checks,

contact your service agent to get it repaired.

CAUTION: All servicing and repair work

on the machine requires special training.

This is especially true of the machine′s

safety equipment. If your machine fails

any of the checks described below you

must contact your service agent. When

you buy any of our products we guarantee

the availability of professional repairs and

service. If the retailer who sells your

machine is not a servicing dealer, ask him

for the address of your nearest service

agent.

To do a check of the keypad

1. Press and hold the start/stop button (A).

C

A

B

a) The product is started when the LED (B) comes

on.

b) The product is stopped when the LED (B) goes

off.

2. Refer to

Keypad on page 16

if the warning indicator

(C) comes on or flashes.

To do a check of the power trigger lockout

The power trigger lockout prevents accidental start.

When you push the power trigger lockout (A), it releases

the power trigger (B). When you release the handle, the

power trigger and the power trigger lockout move back

to their initial positions. This movement is operated by

independent springs.

A

B

1. Make sure that the power trigger is locked when the

power trigger lockout is in its initial position.

8782 - 013 - 21.09.2022

2. Push the power trigger and make sure that it moves

back to its initial position when you release it.

3. Make sure that the power trigger and the lock moves

freely and that the return spring works correctly.

4. Start the product. Refer to

To start the product on

page 13

.

5. Apply full power.

6. Release the power trigger and make sure that the

cutting attachment stops fully.

To do a check of the cutting attachment guard

WARNING: Do not use a cutting

attachment without an approved and

correctly attached cutting attachment guard.

Always use the recommended cutting

attachment guard for the cutting attachment

that you use, see

Technical data on

page 17

. If an incorrect or faulty cutting

attachment guard is attached, it can cause

serious personal injury.

The cutting attachment guard stops objects that eject

in the direction of the operator. The cutting attachment

guard also prevents injuries that can occur if you touch

the cutting attachment.

1. Stop the motor.

2. Do a visual check for damages, for example cracks.

3. Replace the cutting attachment guard if it is

damaged.

Cutting equipment

Select correct cutting equipment and do maintenance on

the cutting equipment to:

• Get maximum cutting performance.

• Increase lifetime of the cutting equipment.

WARNING: Only use cutting

attachments with the guards we

recommend! See

Technical data on page

17

. Refer to the instructions for the cutting

attachment to find the correct way to load

the trimmer line and the correct trimmer line

diameter.

WARNING: A defective cutting

attachment may increase the risk of

accidents.

WARNING: Always stop the engine

before you do the work on the cutting

attachment. This continues to rotate after

you release the throttle. Make sure that the

cutting attachment has stopped fully and

disconnect the spark plug cap before you

start the work on it.

Trimmer head

WARNING: Always make sure the

trimmer line is wound tightly and evenly

around the drum to prevent harmful

vibration.

• Only use recommended trimmer heads and trimmer

lines.

• Only use recommended cutting attachments.

• Smaller machines requires small trimmer heads and

vice versa.

• The length of the trimmer line is important. A longer

trimmer line requires greater engine power than a

shorter trimmer line of the same diameter.

• Make sure that the cutter on the trimmer guard

is intact. This cuts the trimmer line to the correct

length.

• Soak the trimmer line in water for a couple of days

before use to increase the life length.

Battery safety

WARNING: Read the warning

instructions that follow before you use the

product.

782 - 013 - 21.09.2022 9

• Only use the BLi battery. Refer to

Technical data on

page 17

. The battery is software encrypted.

• Use the BLi battery that is rechargable as a power

supply for the related Husqvarna products only. To

prevent injury, do not use the battery as a power

supply for other devices.

• Risk of electrical shock. Do not connect the battery

terminals to keys, coins, screws or other metal. This

can cause a short circuit of the battery.

• Do not use non-rechargeable batteries.

• Do not put objects into the air slots of the battery.

• Keep the battery away from sunlight, heat or open

flame. The battery can cause burns and/or chemical

burns.

• Keep the battery away from rain and wet conditions.

• Keep the battery away from microwaves and high

pressure.

• Do not try to disassemble or break the battery.

• If the battery leaks, do not let the liquid touch your

body or eyes. If you have touched the liquid, clean

the area with a large quantity of water and soap, and

get medical aid. If you get liquid in your eyes, do not

rub but flush with water for a minimum of 15 minutes

and get medical aid.

• Use the battery in temperatures between -10 °C (14

°F) and 40 °C (114 °F).

• Do not clean the battery or the battery charger with

water. Refer to

To clean the product, the battery and

the battery charger on page 15

.

• Do not use a defective or damaged battery.

• Keep batteries in storage away from metal objects

such as nails, screws or jewelry.

• Keep the battery away from children.

Battery charger safety

WARNING: Read the warning

instructions that follow before you use the

product.

• Risk of electrical shock or short circuit if the safety

instructions are not obeyed.

• Do not use other battery chargers than the one

supplied for your product. Only use QC80 / 40-

C80 chargers when you charge BLi replacement

batteries.

• Do not try to disassemble the battery charger.

• Do not use a defective or damaged battery charger.

• Do not lift the battery charger by the power cord. To

disconnect the battery charger from a mains socket,

pull out the plug. Do not pull the power cord.

• Keep all cables and extension leads away from

water, oil and sharp edges. Make sure that the cable

is not caught between objects, for example, doors,

fences or equivalent.

• Do not use the battery charger near flammable

materials or materials that can cause corrosion.

Make sure that the battery charger is not covered.

Pull out the plug to the battery charger if there is

smoke or fire.

• Only charge the battery indoors in a location with

good airflow and away from sunlight. Do not charge

the battery outdoors. Do not charge the battery in

wet conditions.

• Only use the battery charger where the temperature

is between 5 °C (41 °F) and 40 °C (104 °F). Use the

charger in an environment which has a good airflow,

dry and free from dust.

• Do not put objects into the cooling slots of the

battery charger.

• Do not connect the battery charger terminals to

metal objects as this can short circuit the battery

charger.

• Use approved mains sockets that are not damaged.

Make sure that the cord of the battery charger is not

damaged. If extension cables are used, make sure

that the extension cables are not damaged.

Safety instructions for maintenance

WARNING: Read the warning

instructions that follow before you do

maintenance on the product.

• Remove the battery before you do maintenance,

other checks or assemble the product.

• The operator must only do the maintenance and

servicing shown in this operator's manual. Turn to

your servicing dealer for maintenance and servicing

of a larger extension.

• Do not clean the battery or the battery charger with

water. Strong detergent can cause damage to the

plastic.

• If you do not do maintenance, it decreases the

life cycle of the product and increases the risk of

accidents.

• Special training is necessary for all servicing and

repair work, especially for the safety devices on the

product. If not all checks in this operator's manual

are approved after you have done maintenance, turn

to your servicing dealer. We guarantee that there are

professional repairs and servicing available for your

product.

• Only use original spare parts.

10 782 - 013 - 21.09.2022

Assembly

Introduction

WARNING: Read and understand the

safety chapter before you assemble the

product.

To assemble the trimmer guard

1. Assemble the trimmer guard.

.

2. Install the bolt through the housing of the trimmer

head and the trimmer guard.

3. Tighten the bolt.

To assemble the trimmer head

1. Turn the output shaft until the hole in the drive disc

aligns with the hole in the gear housing.

2. Install the locking pin in the hole to lock the shaft.

3. Turn the trimmer head counterclockwise.

To assemble the loop handle

1. Install the screw into the loop handle.

2. Assemble the loop handle to the attachment on the

shaft.

3. Tighten the screws.

4. Adjust the loop handle to a correct position. Refer

to

To adjust the loop handle and telescopic shaft on

page 13

.

To assemble the plant guard

1. Install the plant guard into the holes on the trimmer

head.

2. Make sure that the plant guard can move forward

and rearward freely.

Battery information

Refer to the operator's manual of the battery for

information about how to use the battery.

782 - 013 - 21.09.2022 11

Operation

Introduction

WARNING: Read and understand the

safety chapter before you use the product.

Before you operate the product

• Examine the work area to make sure that you know

the type of terrain. Examine the slope of the ground

and if there are obstacles such as stones, branches

and ditches.

• Do a general inspection of the product.

• Do the safety inspections, maintenance and

servicing that are given in this manual.

• Examine the motor for dirt or cracks. Use a brush to

clean the motor from grass and leaves. Use gloves

when it is necessary.

• Examine the trimmer head and cutting attachment

guard for damages or cracks. Replace the trimmer

head and cutting attachment guard if they are hit or if

they have cracks.

• Make sure that all nuts and screws are tight.

• Make sure that all covers, guards, handles and the

cutting equipment are correctly attached and not

damaged before you start the product.

To connect the battery charger

1. Connect the battery charger to the voltage and

frequency that is specified on the rating plate.

2. Put the plug in a grounded socket outlet. The LED

on the battery charger flashes green one time.

Note: The battery does not charge if the battery

temperature is more than 50 °C/122 °F. If the

temperature is more than 50 °C/122 °F, the battery

charger makes the battery become cool before the

battery charges.

To charge the battery

Note: Charge the battery if it is the first time that you

use it. A new battery is only 30% charged.

1. Connect the battery to the battery charger.

2. Make sure that the green charging light on the

battery charger comes on. That means that the

battery is connected correctly to the battery charger.

3. When all LEDs on the battery come on, the battery is

fully charged.

1

2

3

4. To disconnect the battery charger from the mains

socket, pull the plug. Do not pull the cable.

5. Disconnect the battery from the battery charger.

Note: Refer to the battery and battery charger

manuals for more information.

To connect the battery to the product

WARNING: Only use the initial

Husqvarna battery for the product.

1. Fully charge the battery.

2. Push the battery into the battery holder of the

product. The battery locks into position when you

hear a click.

CAUTION: If the battery does not

move easily into the battery holder, the

battery is not installed correctly. This can

cause damage to the product.

12 782 - 013 - 21.09.2022

To start the product

1. Push and hold the start/stop button until the green

LED comes on.

2. Push the power trigger lockout and the power

trigger. The cutting equipment starts to rotate.

To adjust the loop handle and

telescopic shaft

1. Loosen the locking handle and adjust the loop

handle to a correct position.

2. Close the locking handle.

3. Loosen the lever on the shaft.

4. Set the necessary length on the shaft. Make sure

that you can see the triangle on the shaft.

5. Close the lever and tighten the screw.

Note: Do not attach the loop handle onto the

Warning decals on the shaft.

To use the SavE function

This product has a power saving function, SavE.

Note: The SavE function does not decrease the

cutting power of the product.

1. Press the SavE button on the keypad.

2. Make sure that the green LED comes on.

3. Press the SavE button again to disconnect the

function. The green LED goes out.

Automatic shutdown function

The product has an automatic shutdown function that

stops the product if it is not used. The green LED for

start/stop indication goes off and the product stops after

45 seconds.

782 - 013 - 21.09.2022 13

To operate the product

To trim the grass

1. Hold the trimmer head immediately above the

ground at an angle. Do not push the trimmer line

into the grass.

2. Decrease the length of the trimmer line by 10-12

cm / 4-4.75 in.

3. Decrease the engine speed to decrease the risk of

damage to plants.

4. Use 80 % throttle when you cut grass near objects.

To clear grass

1. Keep the trimmer head above the ground.

2. Tilt the trimmer head.

3. Cut with the end of the trimmer line around objects in

the work area.

CAUTION: Cut grass. Other objects

that are hit by the trimmer line, increases

the wear on the trimmer line.

4. Use 80% speed when you cut and clear vegetation.

This decreases the wear on the trimmer head and

trimmer line.

To cut the grass

1. Make sure that the trimmer line is parallel to the

ground when you cut the grass.

2. Do not push the trimmer head to the ground. This

can cause damage to the product.

3. Move the product from side to side when you cut

grass. Use full speed.

To sweep the grass

The airflow from the rotating trimmer line can be used to

remove cut grass from an area.

1. Hold the trimmer head and the trimmer line parallel

to the ground and above the ground.

2. Apply full throttle.

3. Move the trimmer head from side to side and sweep

the grass.

WARNING: Clean the trimmer head

cover each time you assemble new trimmer

line to prevent unbalance and vibrations in

the handles. Also do a check of the other

parts of the trimmer head and clean it if

necessary.

To stop the product

1. Release the power trigger and the power trigger

lockout.

2. Push the start/stop button until the green LED goes

out.

3. Push the release buttons on the battery and remove

the battery from the product.

14 782 - 013 - 21.09.2022

Maintenance

Introduction

WARNING: Read and understand the

safety chapter before you do maintenance

on the product.

Maintenance schedule

WARNING: Remove the battery before

you do maintenance.

The following is a list of the maintenance steps that you

must do on the product. See

Maintenance on page 15

for more information.

Maintenance Daily Weekly Monthly

Clean the external parts of the product with a dry cloth. Do not use water. X

Examine that the start and stop button works correctly and is not damaged. X

Make sure that the power trigger and the power trigger lockout function correctly

from a safety point of view. X

Make sure that all controls work and are not damaged. X

Keep the handles dry, clean and free from oil and grease. X

Make sure that the cutting attachment is not damaged. Replace the cutting

attachment if it is damaged. X

Make sure that the cutting attachment guard is not damaged. Replace the cut-

ting attachment guard if it is damaged. X

Make sure that the screws and nuts are tight. X

Make sure that the battery release buttons on the battery works and locks the

battery in the product. X

Examine that the battery charger is not damaged and function correctly. X

Make sure that the battery is not damaged. X

Make sure that the battery is charged. X

Make sure that the battery charger is not damaged. X

Examine all cables, couplings and connections. Make sure they are not dam-

aged and free from dirt. X

Do a check of the connections between the battery and the product. Do a check

of the connection between the battery and the battery charger. X

To examine the battery and the battery

charger

1. Examine the battery for damages, for example

cracks.

2. Examine the battery charger for damages, for

example cracks.

3. Make sure that the connection cord of the battery

charger is not damaged and that there are no cracks

in it.

To clean the product, the battery and

the battery charger

1. Clean the product with a dry cloth after use.

782 - 013 - 21.09.2022 15

2. Clean the battery and battery charger with a dry

cloth. Keep the battery guide tracks clean.

3. Make sure that the terminals on the battery and the

battery charger are clean before the battery is put in

the battery charger or the product.

To examine and replace the trimmer

head

1. Do a check of the trimmer head for damages and

cracks.

2. Pull out the chute assembly for the trimmer line.

3. Remove the trimmer head.

4. Replace the trimmer head.

5. Assemble the trimmer head. Refer to

To assemble

the trimmer head on page 11

.

Troubleshooting

Keypad

LED screen Possible faults Possible solutions

The error LED flashes. Overload The cutting attachment cannot move

freely. Release the cutting attach-

ment.

Temperature deviation Let the product cool down.

The product does not start. Push the power trigger and press the

start button at the same time.

Release the power trigger and stop

the product.

The error LED comes on with red

light.

It is necessary to do servicing on the

product

Speak to your service dealer.

Battery

LED display Possible faults Possible action

The green LED flashes. Low battery voltage. Charge the battery.

The error LED flashes. Temperature deviation. Use the battery in temperatures between

-10°C (14°F) and 40°C (104°F).

Too much voltage. Make sure that the mains voltage aligns with

the voltage stated on the rating plate of the

product.

Remove the battery from the battery charger.

The error LED is on. Cell difference is too much (1V). Speak to your servicing dealer.

16 782 - 013 - 21.09.2022

Battery charger

Problem Possible faults Possible solution

Red error LED flashes. Temperature deviation. Use the battery charger in tempera-

tures between 5 °C (41 °F) and 40 °C

(104 °F).

Red error LED comes on. Too much cell difference (1V). Speak to your servicing dealer.

Transportation, storage and disposal

Transportation and storage

• The supplied Li-ion batteries obey the Dangerous

Goods Legislation requirements.

• Obey the special requirement on package and labels

for commercial transportation, including by third

parties and forwarding agents.

• Speak to a person with special training in dangerous

material before you send the product. Obey all

applicable national regulations.

• Use tape on open contacts when you put the battery

in a package. Put the battery in the package tightly

to prevent movement.

• Remove the battery for storage or transportation.

• Put the battery and the battery charger in a space

that is dry and free from moisture and frost.

• Do not keep the battery in an area where static

electricity can occur. Do not keep the battery in a

metal box.

• Put the battery in storage where the temperature is

between 5°C/41°F and 25°C/77°F and away from

open sunlight.

• Put the battery charger in storage where the

temperature is between 5 °C/41 °F and 45°C/113°F

and away from open sunlight.

• Use the battery charger only when the surrounding

temperature is between 5°C/41°F and 40°C/104°F.

• Charge the battery 30% to 50% before you put it in

storage for long periods.

• Put the battery charger in storage in a space that is

closed and dry.

• Keep the battery away from the battery charger

during storage. Do not let children and other not

approved persons to touch the equipment. Keep the

equipment in a space that you can lock.

• Clean the product and do a full servicing before you

put the product in storage for a long time.

• Use the transportation guard on the product to

prevent injuries or damage on the product during

transportation and storage.

• Attach the product safely during transportation.

Disposal of the battery, battery charger

and product

Symbols on the product or the package of the product

means that the product is not domestic waste. Recycle

it at a recycling station for electrical and electronic

equipment. This helps to prevent damage to the

environment and to persons.

Get in touch with your local authorities, domestic waste

service or your dealer for more information about how to

recycle your product.

Technical data

115iL

Platform T100EU

Motor

Motor type BLDC

Speed of output shaft, rpm 5500

782 - 013 - 21.09.2022 17

115iL

Cutting width, mm 330

Weight

Weight without battery, kg 3.45

Weight with battery (BLi10/BLi20), kg 4.25/4.7

Noise emissions 1

Sound power level, measured dB (A) 84

Sound power level, guaranteed LWAdB (A) 86

Noise levels 2

Equivalent sound pressure level at the operator's ear, measured according to EN ISO

50636-2-91, dB (A):

69

Vibration levels 3

Vibration levels at handles, measured according to EN50636-2-91, m/s2

Equipped with trimmer head (original), front/rear.

4.2/1.9

Approved batteries for the product

Battery BLi10 BLi20

Type Lithium-ion Lithium-ion

Battery capacity, Ah 2.1 (VTC4) 2 (HD2) 4.2 (VTC4) 4 (HD2)

Nominal voltage, V 36 36.5 36 36.5

Weight, lb/kg 0.7 0.7 1.2 1.2

Approved battery chargers for the product

Battery charger QC80 40-C80

Mains voltage, V 100-240 100-240

Frequency, Hz 50-60 50-60

Power, W 100 72

Output Voltage, V d.c./ Amps, A 36/2 43/1.6

1Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive

2000/14/EC. The difference between guaranteed and measured sound power is that guaranteed sound power

also includes dispersion in the measurement result and the varaitaions between different products of the

same model refer to Directive 2000/14/EC.

2Reported data for equivalent sound pressure level for the product has a typical statistical dispersion (standard

deviation) of 2.5 dB (A).

3Reported data for vibration level has a typical statistical dispersion (standard deviation) of 1.5 m/s2.

18 782 - 013 - 21.09.2022

Accessories

Approved accessories

Approved accessories Type Cutting attachment guard, Art. no.

Trimmer head T25B M8 (Ø 2.0 mm cord) 585 33 92-01

782 - 013 - 21.09.2022 19

Declaration of Conformity

EU Declaration of Conformity

We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel:

+46-36-146500, declare on our sole responsibility that

the product:

Description Battery-operated Lawn Trimmer

Brand Husqvarna

Type / Model 115iL

Identification Serial numbers dating from 2021 and onwards

complies fully with the following EU directives and

regulations:

Regulation Description

2006/42/EC "relating to machinery"

2014/30/EMC ”relating to electromagnetic compatibility”

2011/65/EU “relating to restriction of hazardous substances”

2000/14/EC "relating to outdoor noise"

and that the following standards

and/or technical specifications are applied:

EN 60335-1:2012+A11:2014+A13:2017, EN

50636-2-91:2014, EN 55014-1:2017+A11:2020, EN

55014-2:1997+A1:2001+A2:2008, EN IEC 63000:2018.

Notified body: 0404, RISE SMP Svensk Maskinprovning

AB, Box 7035, SE-750 07 Uppsala, Sweden

has certified conformity with the council's directive

2000/14/EC, conformity assessment procedure: Annex

VI. The certification has the number 01/1610/012.

Huskvarna, 2022-04-11

Stefan Holmberg, R&D Director, Technology

Management, Husqvarna AB

Responsible for technical documentation

20 782 - 013 - 21.09.2022

Sidan laddas ...

Husqvarna 115iL Cordless Grass Trimmer Användarmanual

Husqvarna 115iL Cordless Grass Trimmer Användarmanual

på andra språk

Relaterade papper

Andra dokument