Yamaha PM5D/PM5D-RH Bruksanvisning

varumärke: Yamaha

Modell: PM5D/PM5D-RH

Kategori: DJ-kontroller

Typ: Bruksanvisning

Denna manual är också lämplig för

PM5D

PM5D Editor Owner’s Manual

Special Notices

•The software and this owner’s manual are the exclu-

sive copyrights of Yamaha Corporation.

•Copying of the software or reproduction of this

manual in whole or in part by any means is expressly

forbidden without the written consent of the manu-

facturer.

•Copying of the commercially available music

sequence data and/or digital audio ﬁles is strictly

prohibited except for your personal use.

•Yamaha makes no representations or warranties

with regard to the use of the software and documen-

tation and cannot be held responsible for the results

of the use of this manual and the software.

•This disc is a CD-ROM. Do not attempt to play the

disc on an audio CD player. Doing so may result in

irreparable damage to your audio CD player.

•The screen displays as illustrated in this owner’s

manual are for instructional purposes, and may

appear somewhat different from the screens which

appear on your computer.

•Future upgrades of application and system software

and any changes in speciﬁcations and functions will

be announced separately.

•The company names and product names in this

Owner’s Manual are the trademarks or registered

trademarks of their respective companies.

❏

Yamaha Pro Audio Global Site

http://www.yamahaproaudio.com/

Contents

Getting Started ......................................... 2

INPUT CH window .................................... 6

ST IN window ............................................ 9

FX RTN window....................................... 11

MIX window ............................................ 13

MATRIX window...................................... 15

STEREO window ...................................... 17

DCA window............................................ 19

Selected Channel window....................... 20

Patch Editor window............................... 38

Surround Editor window......................... 42

GEQ window............................................ 44

Effect Editor window............................... 46

DCA/Mute Group window...................... 50

Scene window ......................................... 53

Library window ....................................... 60

Meter window ......................................... 62

Timecode Counter window..................... 62

Sync window ........................................... 62

Keyboard Shortcuts................................. 63

Index........................................................ 64

*Speciﬁcations and descriptions in this owner ’s manual are

for information purposes only. Yamaha Corp. reserves the

right to change or modify products or speciﬁcations at any

time without prior notice. Since speciﬁcations, equipment

or options may not be the same in every locale, please

check with your Yamaha dealer.

PM5D Editor

Owner’s Manual

Description of menus and buttons

In the event that menu and button names on a Windows system are different from those on a Macintosh, this

manual uses the Windows menu and button names followed by the Macintosh menu and button names in paren-

theses.

PM5D Editor Owner’s Manual

Overview of PM5D Editor

PM5D Editor enables you to remotely control the Yamaha PM5D mixing console and to save the parameter settings

on your computer. To use PM5D Editor, you must ﬁrst perform the following operations:

1 Start and conﬁgure Studio Manager.

2 Start and conﬁgure PM5D Editor.

3 Synchronize PM5D Editor with your PM5D console (

➥

p.3).

For more information on using Studio Manager, refer to the Studio Manager Owner’s Manual.

Conﬁguring PM5D Editor

You must conﬁgure the following settings for each open Editor.

• Specify MIDI ports in the Setup window of Studio Manager before making the following settings.

•To open each Editor, double-click the icon of the console or device you want to edit.

❏

System Setup

To open the System Setup window, choose [System Setup] from the

[File] menu.

Be sure to specify the Input port and Output port.

Input port/Output port:

From the ports you speciﬁed in

Studio Manager, select the ports that the editor will use to commu-

nicate with the PM5D console.

Console Device ID:

PM5D Editor can control any one of up to

eight PM5D consoles, each with its own exclusive ID. Select the ID

of the console you want to control.

Channel Select:

These options determine whether or not chan-

nel selection is linked. When the PC->Console option is on, select-

ing a channel in PM5D Editor selects the same channel on the

console. When the Console->PC option is on, selecting a channel

on the console selects the same channel in PM5D Editor.

Conﬁrmation:

These check boxes specify whether a conﬁrma-

tion dialog box will appear when you store (Store Conﬁrmation), recall (Recall Conﬁrmation), patch (Patch Con-

ﬁrmation), or make a patch change that would modify an existing patch (Steal Patch Conﬁrmation).

Window Control from Console:

This option determines whether or not using the USER DEFINED KEYS

on the console enables you to remotely open and close the PM5D Editor windows.

Getting Started

NOTE

PM5D Editor Owner’s Manual

❏

Console Setup

To open the Mixer Setup window, choose [Mixer Setup] from

the [File] menu.

Pair Mode:

Select whether faders will be paired Horizontally

or Vertically.

Pan Nominal Position:

Select whether the signal will be at

nominal level when panned to the center (Center) or when

panned all the way to left or right (L<->R). You can make sepa-

rate settings for monaural channels and paired channels.

Bus Setup:

Select the MIX bus mode (VARI/FIXED) for

every two adjacent odd-numbered/even-numbered MIX buses.

MIX buses assigned as surround buses are indicated as “SUR-

ROUND” and cannot be changed.

Surround Bus Allocation:

Select the MIX buses (MIX 1–

8 or MIX 9–16) that will be used as surround buses.

Stereo B:

Specify whether the same signal as the STEREO A

bus will be sent to the STEREO B bus (Stereo Bus), or whether

the STEREO B bus will function as the CENTER bus for LCR

mode (Center Bus).

Surround Mode:

Select the surround mode (STEREO, 3-1,

5.1, 6.1).

Synchronizing PM5D Editor

When PM5D Editor starts up, the parameter settings on the console and the parameter settings in PM5D Editor may

be different. Therefore, you must ﬁrst match the parameter settings on the console with those in PM5D Editor. This

operation is called “synchronization.” Follow the steps below to synchronize PM5D Editor.

1 Select [Synchronize], then [Re-synchronize].

The following window opens.

2 Select whether you want to transfer your settings to PM5D

Editor, or vice versa.

At this time, the All Libs option determines whether or not Scene and

Library data is synchronized.

PC -> Console:

Tr ansfers the current parameter settings in PM5D Editor to your console.

Console -> PC:

Tr ansfers the current parameter settings of your console to the PM5D Editor.

3 Click [OK].

Do not operate the console while synchronization is in progress.

If you use the “Total Recall” function in Studio Manager, all selected Editors in Studio Manager are syn-

chronized with the corresponding devices.

Ofﬂine Edit Function

If you do not want to synchronize your console with PM5D Editor, select [Ofﬂine Edit] from the [Synchronization]

menu. To apply your off-line edits to your console, select [Re-Synchronize] from the [Synchronization] with the PC

-> Console option to synchronize the console with PM5D Editor.

The Ofﬂine Edit function is also activated when you click the [ONLINE]/[OFFLINE] button in the Sync window.

Some effect parameters in the console change their displayed values depending on the sampling fre-

quency. If you switch PM5D Editor from OFFLINE to ONLINE, displayed parameter values may change

because PM5D Editor loads the sampling frequency from the console and updates the display.

NOTE

PM5D Editor Owner’s Manual

Working with Sessions

All of your console’s mix settings in PM5D Editor, including Scene and library data, are called Sessions. The follow-

ing table describes how to handle Sessions.

When you save a session in the window of an editor, the settings of only that editor will be saved in a ﬁle. Session ﬁles

saved by PM5D Editor have a ﬁlename extension of “.YSE”. Files in which only the PM5D console data is saved (ﬁle-

name extension “.PM5”) can also be handled, allowing you to use a memory card to exchange data with the PM5D

console.

If you save a Session in the Studio Manager window, all selected Editor settings are saved in a ﬁle with a ﬁle extension

of “.YSM.”

Window operations

You can select and open each window from the [Win-

dows] menu. For the INPUT CH window and Effect Edi-

tor window, use the sub-menu to select the channels or

library you want to see.

In the Library window or Scene window, click the tabs

located at the top of the window to switch between

pages.

Creating a new Session

Choose [New Session] from the [File] menu.

Opening a previously saved Session

Choose [Open Session] from the [File] menu.

Saving the current Session

Choose [Save Session] from the [File] menu.

Saving the current Session with a new name

Choose [Save Session As...] from the [File] menu.

PM5D Editor Owner’s Manual

Undo/Redo Function

In PM5D Editor, you can cancel the latest operation (Undo) and also cancel the cancellation of the latest operation

(Redo). If you perform an Undo operation twice in a row, you can cancel the two most-recent operations. If you per-

form an Undo operation three times in a row, you can cancel the three most-recent operations. In this way, you can

cancel multiple recent operations. The following table describes how to use the Undo/Redo function.

Please note, however, that after you perform one of the following operations, you cannot successfully undo or redo

any previous operation:

•Operations on the PM5D console

• Quitting Studio Manager

•Changing the surround mode or pair mode

•Synchronizing with the PM5D console

•Session operations

•The GEQ [EQ FLAT] button

•Moving the fader positions by changing the GEQ variable width

You cannot Undo or Redo the following operations:

• Edits in the Setup window

• Synchronization

• Opening and closing the windows

• Resizing the windows

In the Library window, you can Undo or Redo only the most recent operation. You cannot cancel the pre-

ceding operations.

Other Functions

❏

Resetting to the default value (Ctrl ( ) + click)

Move the cursor to a control or a parameter value, then hold down the <Ctrl> key ( ) and click the mouse but-

ton to reset the value to the default (e.g., to reset an Input Channel fader to –

∞

, or reset a pan setting to Center).

❏

Ctrl ( ) +Shift+Click

Move the cursor to a fader or AUX Send control, then hold down the <Ctrl> key ( ) and <Shift> key and click

the mouse button to reset the value to the nominal level.

Undo

Choose [Undo] from the [Edit] menu.

Redo

Choose [Redo] from the [Edit] menu.

NOTE

PM5D Editor Owner’s Manual

This window displays the mix parameters of input channels 1–24 or 25–48. The window shows either the channel 1–

24 layer or the channel 25–48 layer. To open the other layer’s window, choose the [Windows] menu command

[INPUT CH] and choose “CH1-24” or “CH25-48.”

You can use the [View] menu to choose the parameters that will be displayed in the window.

Input patch

Here you can select an input source to assign to the input channel, from the following

choices.

+48V

Switches on/off the phantom power (+48V) of the internal head amp (PM5D-RH

model only) or of the external head amp (AD8HR, AD824) patched to the input chan-

nel.

HA GAIN

Drag the knob in the screen to adjust the gain of the internal head amp (PM5D-RH

model only) or of the external head amp (AD8HR, AD824) patched to the input chan-

nel.

NONE

No assignment

AD1–AD48

INPUT jacks 1–48

AD1L–AD4R

L/R channels of ST IN jacks 1–4

SLOT1-1, SLOT1-2...SLOT4-15, SLOT4-16

Input channels of an I/O card installed in slots

1–4

FXOUT1L, FXOUT1R...FXOUT8R,

FXOUT8L

L/R outputs of internal effects 1–8

2TR D1L, 2TR D1R...2TR D3L, 2TR D3R

L/R channels of 2TR IN DIGITAL jacks 1–3

2TR A1L, 2TR A1R...2TR A3L, 2TR A3R

L/R channels of 2TR IN ANALOG jacks 1/2

INPUT CH window

PM5D Editor Owner’s Manual

HPF (High Pass Filter)

Switches the high pass ﬁlter on/off. You can drag the numeric value up or down to edit

the cutoff frequency.

Ø (Phase)

Inverts the phase of the signal after AD conversion.

INSERT

Enables/disables the insert-out that is patched in the PM5D’s INSERT PATCH screen

(INPUT PATCH function).

DIRECT

Enables/disables the direct output that is patched in the PM5D’s DIRECT OUT PATCH

screen (INPUT PATCH function).

GATE

Tur ns the gate on/off. The indica-

tor immediately below the button

shows the gate’s on/off setting

and the open/closed status.

COMP (Compressor)

Switches the compressor on/off. When the compressor is on, the GR meter immediately

below the button shows the amount of gain reduction.

EQ (Equalizer)

Switches the EQ on/off. The graph immediately below the button shows the approxi-

mate response of the EQ. You can drag within the graph to edit the response of the EQ.

To reset the EQ to ﬂat response, hold down the <Ctrl> key ( key) of your computer

keyboard and click the graph.

DELAY

Switches the delay on/off. You can also edit the delay time by dragging the numeric

value located immediately below the button up or down

Channel number

Indicates the input channel number corresponding to this module. You can double-

click this number to open the Selected Channel window for this channel.

MIX SEND

The bar graphs in this area indicate the send levels of

the signals sent from the input channel to VARI-type

MIX buses. You can also adjust the send levels by drag-

ging a bar graph to left or right.

The bar graph display will change according to the

send position (pre/post) and on/off status of the signal

sent from the input channel to the MIX buses.

For FIXED-type MIX buses, the bar graph is ﬁxed at nominal level (0 dB),

and only the on/off status is shown.

N PAN

Sets the panning of the signal sent from the input channel to the STEREO bus.

O SELECT

Selects input channel for which you want to perform operations. This is linked with the

INPUT channel strip [SEL] keys on the PM5D panel. However it will no longer be

linked if you turn Channel Select off (➥ p.2) in the System Setup window.

P CH ON (Channel on) button

Switches the input channel on/off. This is linked with the INPUT channel strip CH

[ON] keys on the PM5D panel.

Gate= closed

(red)

Gate= open

(green)

Gate= off

Pre/on (green)

Pre/off (green)

Post/off (yellow)

Post/on (yellow)

NOTE

PM5D Editor Owner’s Manual

Q Channel name

This is a text box that displays the channel name. You can also edit the channel name in

this text box.

Note that while the channel number (

L) will not change even if you switch the pair

mode, the channel name display will change according to the pair mode.

For example if the CH1-24 layer is displayed, switching from Horizontal Pair mode to

Ve rtical Pair mode will change the channel name display from channels 1, 2, 3 ... 24, 25

to channels 1, 3, 5...45, 47.

R Fader

Adjusts the input level of the input channel. This is linked with the INPUT channel

strip faders on the PM5D panel.

The current fader value is shown in the numeric box immediately below the fader. The

level meter at the right of the fader shows the level of the input signal.

The numbers and

alphabetical letters at

the right of the fader

indicate the DCA

group and mute

groups to which that

channel belongs, and

show the Recall Safe

and Mute Safe status of

the channel.

S CUE

This button cue-monitors the signal of the input channel. This is linked with the

INPUT channel strip [CUE] keys on the PM5D panel.

The numbers of DCA groups to which this

channel belongs are shown in yellow.

The numbers of mute groups to which this

channel belongs are shown in red.

If this channel is set to Recall Safe, the R

character is shown in orange.

If this channel is set to Mute Safe, the M char-

acter is shown in red.

PM5D Editor Owner’s Manual

In this window you can view and edit the mix parameters of ST IN channels 1–4. You can use the [View] menu to

choose the parameters that will be displayed in the window.

A Input patch

Selects the input source that will be assigned to the ST IN channel. The input sources

that can be assigned are the same as for an input channel (➥ p.6).

B +48V

Switches on/off the phantom power (+48V) of the internal head amp (PM5D-RH

model only) or of the external head amp (AD824, AD8HR) patched to the ST IN chan-

nel.

C HA GAIN

Drag the knob in the screen to adjust the gain of the internal head amp (PM5D-RH

model only) or of the external head amp (AD824, AD8HR) patched to the ST IN chan-

nel.

D HPF (High Pass Filter)

Switches the high pass ﬁlter on/off. You can drag the numeric value up or down to edit

the cutoff frequency.

E Ø (Phase)

Inverts the phase of the signal after AD conversion.

F INSERT

Enables/disables the insert-out that is patched in the PM5D’s INSERT PATCH screen

(INPUT PATCH function). (The L/R settings are linked.)

G DIRECT

Enables/disables the direct out that is patched in the PM5D’s DIRECT OUT PATCH

screen (INPUT PATCH function). (The L/R settings are linked.)

ST IN window

PM5D Editor Owner’s Manual

H GATE

Tur ns the gate on/off. The indicator immediately below the button shows the gate’s on/

off setting and the open/closed status (➥ p.7).

I COMP (Compressor)

Switches the compressor on/off. When the compressor is on, the GR meter immediately

below the button shows the amount of gain reduction.

J EQ (Equalizer)

Switches the EQ on/off (the L/R settings are linked). The graph immediately below the

button shows the approximate response of the EQ. You can drag the graph to edit the

response of the EQ, or hold down the <Ctrl> key ( key) of your computer keyboard

and click the graph to reset it to a ﬂat response.

K DELAY

Switches the delay on/off. You can also edit the delay time by dragging the numeric

value located immediately below the button up or down

L Channel number

This is the number of the ST IN channel for this module. You can double-click this

number to open the Selected Channel window for this channel.

M MIX SEND

The send levels of the signals sent from the ST IN channel to the VARI-type MIX buses

are shown as bar graphs (the L/R settings are linked). You can also adjust the send levels

by dragging a bar graph to left or right.

The bar graph display will change according to the send position (pre/post) and on/off

status of the signal sent from the ST IN channel to the MIX buses (➥ p.7).

N PAN

Speciﬁes the panning of the signal sent from the ST IN channel to the STEREO bus.

(You can set L and R separately.)

O SELECT

Selects the ST IN channel for which you want to perform operations. (L and R can be

selected separately.) This is linked with the ST IN channel strip [SEL] keys on the

PM5D panel. However it will no longer be linked if you turn Channel Select off (➥ p.2)

in the System Setup window.

P CH ON (Channel on) button

Switches the ST IN channel on/off (the L/R settings are linked). This is linked with the

ST IN channel strip CH [ON] keys on the PM5D panel.

Q Channel name

This is a text box that displays the channel name. You can also edit the channel name in

this text box.

R Fader

Adjusts the input level of the ST IN channel. This is linked with the faders of the ST IN

channel strip on the PM5D panel.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel (➥ p.8).

S CUE

This button cue-monitors the signal of the ST IN channel (L/R are linked). This is

linked with the ST IN channel strip [CUE] keys on the PM5D panel.

PM5D Editor Owner’s Manual

In this window you can view and edit the mix parameters of FX RTN channels 1–4. You can use the [View] menu to

choose the parameters that will be displayed in the window.

A Input patch

Selects the input source that will be assigned to the FX RTN channel. The input sources

that can be assigned are the same as for an input channel (➥ p.6).

B +48V

Switches on/off the phantom power (+48V) of the internal head amp (PM5D-RH

model only) or of the external head amp (AD8HR, AD824) patched to the FX RTN

channel.

C HA GAIN

Drag the knob in the screen to adjust the gain of the internal head amp (PM5D-RH

model only) or of the external head amp (AD8HR, AD824) patched to the FX RTN

channel.

D HPF (High Pass Filter)

Switches the high pass ﬁlter on/off. You can drag the numeric value up or down to edit

the cutoff frequency.

E Ø (Phase)

Inverts the phase of the signal after AD conversion.

F EQ (Equalizer)

Switches the EQ on/off (the L/R settings are linked). The graph immediately below the

button shows the approximate response of the EQ. You can drag the graph to edit the

response of the EQ, or hold down the <Ctrl> key ( key) of your computer keyboard

and click the graph to reset it to a ﬂat response.

FX RTN window

PM5D Editor Owner’s Manual

G Channel number

This is the number of the FX RTN channel for this module. You can double-click this

number to open the Selected Channel window for this channel.

H MIX SEND

The send levels of the signals sent from the FX RTN channel to the VARI-type MIX

buses are shown as bar graphs (the L/R settings are linked). You can also adjust the send

levels by dragging a bar graph to left or right.

The bar graph display will change according to the send position (pre/post) and on/off

status of the signal sent from the FX RTN channel to the MIX buses (➥ p.7).

I PAN

Speciﬁes the panning of the signal sent from the FX RTN channel to the STEREO bus.

(You can set L and R separately.)

J SELECT

Selects the FX RTN channel for which you want to perform operations. (L and R can be

selected separately.) This is linked with the FX RTN channel strip [SEL] keys on the

PM5D panel. However it will no longer be linked if you turn Channel Select off (➥ p.2)

in the System Setup window.

K CH ON (Channel on) button

Switches the FX RTN channel on/off. (The L/R settings are linked.) This is linked with

the FX RTN channel strip CH [ON] keys on the PM5D panel.

L Channel name

This is a text box that displays the channel name. You can also edit the channel name in

this text box.

M Fader

Adjusts the input level of the FX RTN channel. This is linked with the faders of the FX

RTN channel strip on the PM5D panel.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel (➥ p.8).

N CUE

This button cue-monitors the signal of the FX RTN channel (L/R are linked). This is

linked with the FX RTN channel strip [CUE] keys on the PM5D panel.

PM5D Editor Owner’s Manual

In this window you can view and edit the parameters of MIX channels 1–24. You can use the [View] menu to choose

the parameters that will be displayed in the window.

A EQ (Equalizer)

Switches the EQ on/off. The graph immediately below the button shows the approxi-

mate response of the EQ. You can drag the graph to edit the response of the EQ, or hold

down the <Ctrl> key ( key) of your computer keyboard and click the graph to reset

it to a ﬂat response.

B COMP (Compressor)

Switches the compressor on/off. When the compressor is on, the GR meter immediately

below the button shows the amount of gain reduction.

C INSERT

Enables/disables the insert-out that is patched in the PM5D’s INSERT PATCH screen

(OUTPUT PATCH function).

D DELAY

Switches the delay on/off. You can also edit the delay time by dragging the numeric

value located immediately below the button up or down

E Channel number

Indicates the number of the MIX channel corresponding to this module. You can dou-

ble-click this number to open the Selected Channel window for this channel.

MIX window

PM5D Editor Owner’s Manual

F MTRX (Send level to MATRIX buses)

These bar graphs indicate the send levels of the signals

sent from the MIX channel to each MATRIX bus. You

can also adjust the send levels by dragging a bar graph

to left or right.

The bar graph display will change as follows according

to the send position (pre/post) and on/off status of the

signal sent from the MIX channel to the MATRIX

buses.

G TO ST (To STEREO)

This is an on/off switch for the signal sent from the MIX channel to the STEREO bus.

H PAN

Sets the panning of the signal sent from the MIX channel to the STEREO bus.

I VARI/FIXED

Indicates the type (VARI or FIXED) of the currently selected MIX bus. (This parameter

is for display only. You cannot switch between VARI and FIXED from within PM5D

Editor.)

If surround mode is enabled, MIX buses that are assigned as surround buses are dis-

played with the name of the surround channel (L, R, Ls, Rs ...), and the other MIX

buses are displayed as “FIXED.”

J SELECT

Selects the MIX channel for which you want to make settings. This is linked with the

MIX [SEL] keys in the MIX section of the PM5D panel. However it will no longer be

linked if you turn Channel Select off (➥ p.2) in the System Setup window.

K ON

Switches the MIX channel on/off.

L Fader

Adjusts the output level of the MIX channel. The current fader value is shown in the

numeric box immediately below the fader. The level meter at the right of the fader

shows the output level of the signal.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel. (For the signiﬁcance of the numbers and alphabetical letters,

see ➥ p.8).

M CUE

This button cue-monitors the signal of the MIX channel. This is linked with the MIX

[CUE] keys in the MIX section of the PM5D panel.

Pre/on (green)

Pre/off (green)

Post/off (yellow)

Post/on (yellow)

PM5D Editor Owner’s Manual

In this window you can view and edit the parameters of MATRIX channels 1–8. You can use the [View] menu to

choose the parameters that will be displayed in the window.

MATRIX window

PM5D Editor Owner’s Manual

A MIX (Send levels from the MIX channels to the MATRIX bus)

Here you can view and edit the send levels of the signals sent from each MIX channel to

the MATRIX bus. The method of operation and the meaning of the display are the same

as for (

6) MTRX in the MIX window (➥ p.14).

B STEREO (Send levels from the STEREO channels to the MATRIX

bus)

Here you can view and edit the send levels of the signals sent from the STEREO A/B

channels to the MATRIX bus. The method of operation and the meaning of the display

are the same as for (

6) MTRX in the MIX window (➥ p.14).

C Channel number

Indicates the number of the MATRIX channel corresponding to this module. You can

double-click this number to open the Selected Channel window for this channel.

D EQ (Equalizer)

Switches the EQ on/off. The graph immediately below the button shows the approxi-

mate response of the EQ. You can drag the graph to edit the response of the EQ, or hold

down the <Ctrl> key ( key) of your computer keyboard and click the graph to reset

it to a ﬂat response.

E COMP (Compressor)

Switches the compressor on/off. When the compressor is on, the GR meter immediately

below the button shows the amount of gain reduction.

F INSERT

Enables/disables the insert-out that is patched in the PM5D’s INSERT PATCH screen

(OUTPUT PATCH function).

G DELAY

Switches the delay on/off. You can also edit the delay time by dragging the numeric

value located immediately below the button up or down

H SELECT

Selects the MATRIX channel for which you want to make settings. This is linked with

the MATRIX [SEL] keys in the MATRIX section of the PM5D panel. However it will no

longer be linked if you turn Channel Select off (➥ p.2) in the System Setup window.

I ON

This switches the MATRIX channel on/off. This is linked with the MATRIX [ON] keys

in the MATRIX section of the PM5D panel.

J Fader

This adjusts the output level of the MATRIX channel. The current fader value is shown

in the numeric box immediately below the fader. The level meter at the right of the

fader shows the output level of the signal.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel. (For the signiﬁcance of the numbers and alphabetical letters,

see ➥ p.8).

K CUE

This button cue-monitors the signal of the MATRIX channel. This is linked with the

MATRIX [CUE] keys in the MATRIX section of the PM5D panel.

PM5D Editor Owner’s Manual

In this window you can view and edit the parameters of the STEREO A/B channels. You can use the [View] menu to

choose the parameters that will be displayed in the window.

STEREO window

PM5D Editor Owner’s Manual

A EQ (Equalizer)

Switches the EQ on/off (the L/R settings are linked). The graph immediately below the

button shows the approximate response of the EQ. You can drag the graph to edit the

response of the EQ, or hold down the <Ctrl> key ( key) of your computer keyboard

and click the graph to reset it to a ﬂat response.

B COMP (Compressor)

Switches the compressor on/off (the L/R settings are linked). When the compressor is

on, the GR meter immediately below the button shows the amount of gain reduction.

C INSERT

Enables/disables the insert-out that is patched in the PM5D’s INSERT PATCH screen

(OUTPUT PATCH function). (The L/R settings are linked.)

D DELAY

Switches the delay on/off. (L/R settings can be made independently.) You can also edit

the delay time by dragging the numeric value located immediately below the button up

or down

E Channel number

This is the channel number (STEREO A or B) of this module. You can double-click this

number to open the Selected Channel window for this channel.

F MTRX (Send level to MATRIX buses)

Here you can view and edit the send levels of the signals sent from the STEREO A/B

channel to each MATRIX bus. The method of operation and the meaning of the display

are the same as for (

6) MTRX in the MIX window (➥ p.14).

G BALANCE

Adjusts the left/right balance of the STEREO A/B channel.

H SELECT

Selects the STEREO A/B channel for which you want to make settings. (You can specify

L and R independently.) This is linked with the STEREO [SEL] key in the STEREO A/B

channel strip of the PM5D panel. However it will no longer be linked if you turn Chan-

nel Select off (➥ p.2) in the System Setup window.

I ON

This switches the STEREO A/B channel on/off. This is linked with the STEREO [ON]

key in the STEREO A/B channel strip of the PM5D panel.

J Fader

Adjusts the output level of the STEREO A/B channel. This is linked with the STEREO

fader in the STEREO A/B channel strip of the PM5D panel.

The current fader value is shown in the numeric box immediately below the fader. The

level meter at the right of the fader shows the output level of the signal.

The numbers and alphabetical letters at the right of the fader indicate the DCA group

and mute groups to which that channel belongs, and show the Recall Safe and Mute

Safe status of the channel. (For the signiﬁcance of the numbers and alphabetical letters,

see ➥ p.8).

K CUE

This button cue-monitors the signal of the STEREO A/B channel. This is linked with

the STEREO [CUE] key in the STEREO A/B channel strip of the PM5D panel.

PM5D Editor Owner’s Manual

In this window you can view and edit the parameters of DCA groups 1–8.

A DCA number

This is the number of the DCA group.

B MUTE

This switches DCA group muting on/off. This is linked with the DCA [MUTE] keys in

the DCA strip section of the PM5D panel.

C DCA group name

This is a text box that displays the DCA group name. You can also edit the DCA group

name in this text box.

D DCA fader

This fader adjusts the level of the DCA group. This is linked with the DCA faders in the

DCA strip section of the PM5D panel.

The current fader value is shown in the numeric box immediately below the fader.

When you hold down the <Ctrl> key ( key) and <Shift> key of your computer key-

board and click a fader, the corresponding fader will be set to nominal level (0 dB).

When the fader is at nominal level, the N character at the right of the fader is displayed

in green.

If a DCA group is set to Recall Safe, the R character at the lower right of the fader is dis-

played in orange.

E CUE

This button cue-monitors the DCA group. This is linked with the DCA [CUE] keys in

the DCA channel strip of the PM5D panel.

DCA window

PM5D Editor Owner’s Manual

Here you can set the parameters of the currently selected input channel (input channels 1–48, ST IN channels 1–4,

FX RTN channels 1–4) or output channel (MIX channels 1–24, MATRIX channels 1–8, STEREO A/B channels).

The type of parameters that can be edited in this window will depend on the type of the currently selected channel.

The parameters of the Selected Channel window are explained below, in the order of input channels (input channels

1–48, ST IN channels 1–4, FX RTN channels 1–4), MIX channels, MATRIX channels, and STEREO A/B channels.

If an input channel is selected

Unless otherwise speciﬁed, the parameters explained below are common to input channels 1–48, ST IN

channels 1–4, and FX RTN channels 1–4.

❏ CHANNEL SELECT (Channel selection)

A SELECT (Channel selection)

Indicates the number and name of the channel you are editing. To switch channels, use the SELECT button or the

/ buttons at left and right. You can also edit the channel name in the text box.

B PAIR

Indicates the pair status of the selected channel. You can click the heart symbol to enable/disable pairing.

C INPUT PATCH

Selects the input source assigned to the input channel (for the selectable input sources, ➥ p.6).

D LIBRARY

Accesses the INPUT CH page of the LIBRARY window.

Selected Channel window

NOTE

1 2 43

Sidan laddas ...

Yamaha PM5D/PM5D-RH Bruksanvisning

varumärke: Yamaha

Modell: PM5D/PM5D-RH

Kategori: DJ-kontroller

Typ: Bruksanvisning

Denna manual är också lämplig för

PM5D

Ladda ner pdf

Rapportera

på andra språk

italiano: Yamaha PM5D/PM5D-RH Manuale del proprietario
čeština: Yamaha PM5D/PM5D-RH Návod k obsluze
español: Yamaha PM5D/PM5D-RH El manual del propietario
Deutsch: Yamaha PM5D/PM5D-RH Bedienungsanleitung
polski: Yamaha PM5D/PM5D-RH Instrukcja obsługi
português: Yamaha PM5D/PM5D-RH Manual do proprietário
français: Yamaha PM5D/PM5D-RH Le manuel du propriétaire
Türkçe: Yamaha PM5D/PM5D-RH El kitabı
English: Yamaha PM5D/PM5D-RH Owner's manual
dansk: Yamaha PM5D/PM5D-RH Brugervejledning
русский: Yamaha PM5D/PM5D-RH Инструкция по применению
suomi: Yamaha PM5D/PM5D-RH Omistajan opas
Nederlands: Yamaha PM5D/PM5D-RH de handleiding
română: Yamaha PM5D/PM5D-RH Manualul proprietarului

Yamaha PM5D/PM5D-RH Bruksanvisning

Denna manual är också lämplig för

Yamaha PM5D/PM5D-RH Bruksanvisning

på andra språk

Relaterade papper