Yamaha EMX 5000-20 Användarmanual

varumärke: Yamaha

Modell: EMX 5000-20

Kategori: Ljudmixer

Typ: Användarmanual

Denna manual är också lämplig för

Owner’s Manual

Keep This Manual For Future Reference.

EMX5000-20/EMX5000-12

The Owner’s Manual Revisions

Thank you for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. Parts of the EMX5000-20, EMX5000-12 owner’s

manual have been revised. Please refer to the following revisions rather than the corresponding sections of the original owner’s

manual.

P.14

■

POWER amp section

LIMITER indicator

If the output level of signals received at the SPEAKERS

jacks (output of the internal power ampliﬁer) reaches

maximum, the indicator will light.

P.15

■

Other indicators and controls

Level Meter

This LED display shows the

level of signals received at the

ST OUT jack (input/output

panel

P.18

Rear panel

SPEAKERS (speaker output) jacks

These jacks are used to connect speakers.

Jacks 1 are Speakon-type connectors. Use only Neutrik

NL4FC plugs for connecting Speakon connectors.

Jacks 2 are 1/4”phone jacks. The setting of the control

panel power amp select switch

will determine the sig-

nal that is output to these jacks, and the number and

appropriate impedance of the speakers that can be con-

nected.

P.33

Block/Level Diagram

Power Ampliﬁer output section level diagram (bottom right)

These plots show the nominal output and maximum output

levels of signals received at the SPEAKERS jacks. If the output

level is +4dB (Level Meter “0”), the internal power ampliﬁer

will deliver 100W into a 4

Ω

load. If the output level is +11dB

(LIMITER indicator lights), the internal ampliﬁer will deliver

a maximum of 500W into 4

Ω

Caution:

If the LIMITER indicator flashes continuous-

ly, the internal power amplifier section is being exces-

sively overloaded and may malfunction. Reduce the

output level at the ST OUT fader (

) below the level

that the indicator flashes only briefly on the highest

transient peaks.

Note:

The SPEAKERS 1 & 2 jacks (rear panel

) out-

put the signals received at the ST OUT jack via the inter-

nal power amplifier. Check the output signal level via

the LIMITER indicator (

). The LIMITER indicator

will light before the Level Meter “8” or “PEAK” LED

light.

2–

1–

Neutrik NL4FC

CHANNEL A

STEREO/PARALLEL BRIDGE

1+ A+

1– A–

2+ B+

2– B–

CHANNEL B

1+ B+

1– B–

1+ +

1–

2+ –

2–

+30dB

+20dB

+10dB

0dB

+11dB

+4dB

SPEAKERS OUT

MAXIMUM OUTPUT [500W/4Ω]

NOMINAL OUTPUT [100W/4Ω]

EMX5000-20/EMX5000-12

Block/Level Diagram

CH INPUT

[–60~–16dB]

[–34~+10dB]

CH INSERT I/O

[0dB]

EMX5000-12:CH1-8

EMX5000-20:CH1-16

EMX5000-12:CH1-8

EMX5000-20:CH1-16

GAIN

[–60~–16dB]

[–34~+10dB]

PHANTOM

8CH/SW

EMX5000-12:[CH1-8]

EMX5000-20:[CH1-8] [CH9-16]

PA D

HPF

+48V

26dB

[0dB]

3-Stage EQ

Lo Gain

Hi Gain

Mid f

Mid Gain

[–10dB]

[0dB]

CH Fader

PEAK

SIGNAL

PA N

POST

PFL

POST

EFFECT1

EFFECT2

AUX1

AUX2

[0dB]

[–6dB]

STEREO L (NON-MUTE)

STEREO R (NON-MUTE)

EFFECT1 (NON-MUTE)

EFFECT2 (NON-MUTE)

AUX1 (NON-MUTE)

AUX2 (NON-MUTE)

STEREO L (MUTE)

STEREO R (MUTE)

EFFECT1 (MUTE)

EFFECT2 (MUTE)

AUX1 (MUTE)

AUX2 (MUTE)

PFL L / AFL L

PFL R / AFL R

PFL

AFL

SUM

[0dB]

STAND-BY

EMX5000-12:CH1-8

EMX5000-20:CH1-16

SUM

[0dB]

REC OUT

[–10dBV]

9-Stage GEQ

63Hz

125Hz

250Hz

500Hz

1kHz

2kHz

4kHz

8kHz

16kHz

GEQ

[–6dB]

[–10dB]

ST OUT

ST SUB OUT

[+4dB]

ST OUT

[+4dB]

PEAK

YSP

POWER AMP IN

[+4dB]

YA MAHA

SPEAKER

PROCESSING

LIMITTER

PROTECTOR

Power Select

SPEAKERS

[500Wmax@4ohms]

BRIDGE

500W

300W

100W

500W

300W

100W

–1

–2

–1

–2

POWER AMP Controls

INV

Signal Select

MAIN L

AUX1

MONO BRIDGE

MAIN R

MONO

AUX2

MONO BRIDGE

FREQ

80–120Hz

(12dB/oct)

INV

LPF

SUM

MONO OUT

[+4dB]

[–10dB]

MONO OUT

AUX SEND1

[+4dB]

AUX SEND2

[+4dB]

[–10dB]

AUX1

[–10dB]

AUX2

AFL

SUM

[0dB]

SUM

[0dB]

SUM

[0dB]

SUM

[0dB]

SUMSUM

SUM

[–6dB]

SUM

[–6dB]

SUM

[0dB]

SUM

[0dB]

INV

[0dB]

INV

[0dB]

PFL

POST

BAL

EFFECT1

EFFECT2

AUX1

AUX2

[0dB]

[–6dB]

[0dB]

[–10dB]

ST CH Fader

PEAK

SIGNAL

GAIN

[–34~+10dB]

ST CH INPUT

[–34~+10dB]

EMX5000-12:CH9(L)/10(R),CH11(L)/12(R)

EMX5000-20:CH17(L)/18(R),CH19(L)/20(R)

[0dB]

3-Stage EQ

Mid

PA D

PFL

AUX1

AUX2

[0dB]

[+4dB] [–6dB]

[–6dB]

[–16dB]

ST SUB IN 1,2

[+4dB]

L (MONO)

2TR IN

[–10dBV]

[0dB]

[–6dB]

PROGRAM

PARAMETER

PROGRAM

PARAMETER

DIGITAL

EFFECT1

L OUT

R OUT

DIGITAL

EFFECT2

L OUT

R OUT

EFFECT1 RTN

EFFECT2 RTN

PFL

AUX1

AUX2

[–12dB]

AUX1

AUX2

[–12dB]

FOOT SWITCH

TA P

ON/OFF

0dB=0.775V

0dBV=1V

+30dB

+20dB

+10dB

0dB

–10dB

–20dB

–30dB

–40dB

–50dB

–60dB

ST CH INPUT

GAIN Min. [+10dB]

ST CH INPUT

GAIN Max. [–34dB]

CH INPUT A, B

GAIN Max. [–60dB]

CH INPUT A, B GAIN Min. [–16dB]

ST SUB IN [+4dB]

CH & ST CH to ST [0dB] (PAN, BAL turned hard left/right)

CH & ST CH to AUX/EFFECT [–6dB]

ST SUB IN to ST/AUX [–6dB]

2TR IN to ST [–6dB]

2TR IN [–10dBV]

fader [–10dB]

[PHONES 3mW@40ohms]

ST OUT•ST SUB OUT•MONO OUT [+4dB]

AUX SEND, EFFECT SEND [+4dB]

REC OUT [–10dBV]

PHONES [–16dB]

ST SUB level control [–6dB]

EFFECT [–6dB]

ST•MONO•AUX fader [–10dB]

SPEAKERS OUT

MAXIMUM OUTPUT [500W/4Ω]

NOMINAL OUTPUT [100W/4Ω]

+40dB

+30dB

+20dB

+10dB

0dB

–10dB

–20dB

–30dB

–40dB

–50dB

–60dB

INV

EFFECT SEND1

[+4dB]

EFFECT SEND2

[+4dB]

PHONES

[3mW@40ohms]

[–16dB]

PHONES

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST

be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with

these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with

other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may

cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all

installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the

problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on

different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in

is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service

Division, 6600 Orangethorpe Ave, Buena Park, CA 90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magni-

tude to constitute a risk of electric shock to

persons.

The exclamation point within an equilat-

eral triangle is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The above warning is located on the

rear of the unit.

European Specifications Only

This mark indicates a dangerous electrically live terminal.

When connecting an external wire to this terminal, it is

necessary either to have “a person who have received

appropriate guidance on handling” make the connection or to

use leads or a cord that have been manufactured in such a way

that the connection can be made simply and without problem.

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows:

The wire which is coloured GREEN and YELLOW must be

connected to the terminal in the plug which is marked by the letter E

or by the safety earth symbol or coloured GREEN and YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

* This applies only to products distributed by YAMAHA KEMBLE

MUSIC (U.K.) LTD.

Precautions

EMX5000-20/EMX5000-12—Owner’s Manual

Precautions

WARNING

• Connect this unit’s power cord only to an AC outlet of the type

stated in this Owner’s Manual or as marked on the unit. Failure

to do so is a ﬁre and electrical shock hazard.

• Do not allow water to enter this unit or allow the unit to

become wet. Fire or electrical shock may result.

• Do not place a container with liquid or small metal objects on

top of this unit. Liquid or metal objects inside this unit are a ﬁre

and electrical shock hazard.

• Do not place heavy objects, including this unit, on top of the

power cord. A damaged power cord is a ﬁre and electrical shock

hazard. In particular, be careful not to place heavy objects on a

power cord covered by a carpet.

• Use only the included power cord for this unit. Using other

types may be a ﬁre and electrical shock hazard.

• The power to this device is not completely shut off even when

the power switch is turned off. Locate the device close to the AC

outlet so you can easily reach the power plug.

• Do not scratch, bend, twist, pull, or heat the power cord. A

damaged power cord is a ﬁre and electrical shock hazard.

• Do not remove the unit’s cover. You could receive an electrical

shock. If you think internal inspection, maintenance, or repair

is necessary, contact your dealer.

• Do not modify the unit. Doing so is a ﬁre and electrical shock

hazard.

• If lightning begins to occur, turn off the power switch of the

unit as soon as possible, and unplug the power cable plug from

the electrical outlet.

• If there is a possibility of lightning, do not touch the power

cable plug if it is still connected. Doing so may be an electrical

shock hazard.

• If the power cord is damaged (i.e., cut or a bare wire is

exposed), ask your dealer for a replacement. Using the unit

with a damaged power cord is a ﬁre and electrical shock hazard.

• Should this unit be dropped or the cabinet be damaged, turn the

power switch off, remove the power plug from the AC outlet,

and contact your dealer. If you continue using the unit without

heeding this instruction, ﬁre or electrical shock may result.

• If you notice any abnormality, such as smoke, odor, or noise, or

if a foreign object or liquid gets inside the unit, turn it off

immediately. Remove the power cord from the AC outlet. Con-

sult your dealer for repair. Using the unit in this condition is a

ﬁre and electrical shock hazard.

CAUTION

• Keep this unit away from the following locations:

- Locations exposed to oil splashes or steam, such as near

cooking stoves, humidiﬁers, etc.

- Unstable surfaces, such as a wobbly table or slope.

- Locations exposed to excessive heat, such as inside a car with

all the windows closed, or places that receive direct sunlight.

- Locations subject to excessive humidity or dust accumula-

tion.

• Hold the power cord plug when disconnecting it from an AC

outlet. Never pull the cord. A damaged power cord is a poten-

tial ﬁre and electrical shock hazard.

• Do not touch the power plug with wet hands. Doing so is a

potential electrical shock hazard.

• This unit has ventilation holes at the rear to prevent the internal

temperature rising too high. Do not block them. Blocked venti-

lation holes are a ﬁre hazard.

• To relocate the unit, turn the power switch off, remove the

power plug from the AC outlet, and remove all connecting

cables. Damaged cables may cause ﬁre or electrical shock.

• Turn off all musical instruments, audio equipment, and speak-

ers when connecting to this unit. Use the correct connecting

cables and connect as speciﬁed.

• Always lower the volume control to minimum before turning

on the power to this unit. A sudden blast of sound may damage

your hearing.

• Use only speaker cables when connecting speakers to ampliﬁer

outputs. Using other types of cables is a ﬁre hazard.

• If you know you will not use this unit for a long period of time,

such as when going on vacation, remove the power plug from

the AC outlet. Leaving it connected is a potential ﬁre hazard.

• Clean the contacts of the phone plug before connecting it to the

SPEAKERS jack of this unit. Dirty contacts may generate heat.

• To prevent electrical shock when cleaning the unit, remove the

power plug from the AC outlet.

Installation

Operation

In case an abnormality occurs during operation

Installation

Operation

Maintenance

Precautions

EMX5000-20/EMX5000-12—Owner’s Manual

• XLR-type connectors are wired as follows: pin 1: ground, pin 2:

hot (+), and pin 3: cold (–).

• Insert TRS phone jacks are wired as follows: sleeve: ground, tip:

send, and ring: return.

• The performance of components with moving contacts, such

switches, rotary controls, faders, and connectors, deteriorates

over time. The rate of deterioration depends on the operating

environment and is unavoidable. Consult your dealer about

replacing defective components.

• Using a cell phone (mobile telephone) near this unit may induce

noise. If noise occurs, use the telephone away from the unit.

• Do not set all equalizer controls and faders to maximum.

Doing so may cause oscillation depending on the condition of

the connected unit and speakers, and may damage the speakers.

• The digital circuits of this unit may induce a slight noise into

nearby radios and TVs. If noise occurs, relocate the affected

equipment.

PRECAUTIONS FOR OPERATION – FOR CORRECT OPERATION –

Replacing abrasive parts

Connector pin assignments

Influence on cell phone usage

Volume level setting

Interference with other electronic devices

Introduction

EMX5000-20/EMX5000-12—Owner’s Manual

Introduction

Thank you for purchasing the Yamaha

EMX5000-20/EMX5000-12

Powered Mixer.

In order to take full advantage of the

EMX5000-20/EMX5000-12

and enjoy long,

trouble-free performance, please read this owner’s manual carefully, and keep it

in a safe place for future reference.

Features

• The EMX5000-20/EMX5000-12 provides versatile

inputs, such as two stereo input channels and two ste-

reo sub inputs, as well as 16 (EMX5000-20), 8

(EMX5000-12) monaural input channels compatible

with mic/line signals. The mixer also has ample power,

with a maximum output of 500 W+500 W (1000 W

with bridge connection), and is suitable for a wide

range of applications from installed systems to small-

scale PA systems.

• A two-channel power amp is built-in. The signals out-

put to speakers can be selected as stereo (ST L-R),

AUX+monaural (AUX 1- MONO), two AUX (AUX1-

AUX2) or monaural (bridge connection).

• In addition to the speaker output jacks, two stereo

output channels for line-level signals, two AUX output

channels, two effect outputs, and one monaural out-

put are provided. You can easily expand the system by

adding a power ampliﬁer or powered speakers.

• The EMX5000-20/EMX5000-12 also has a PHONES

jack, which is very useful for checking the sound. You

can monitor only a speciﬁc channel or bus signal

through the headphones.

• Each amp contains a limiter circuit to prevent distor-

tion due to excessive input levels.

• A maximum output select switch lets you switch the

maximum output of the amp between three levels.

This lets you adjust the maximum output of the inter-

nal power amp as appropriate for the size of the room

or the input capacity of the speakers.

• Two multi-effect units are built-in, each providing six-

teen types of effect equivalent in quality to the

acclaimed Yamaha SPX series of multi-effect units.

The effects can be used to add reverb or ambience to

vocals or instruments. The sixteen types (provided by

each of the two effect units) include TAP DELAY,

which lets you easily adjust the delay time.

• The EMX5000-20/EMX5000-12 has implemented

“EEEngine”, Yamaha’s epochal amp drive technology

to create an unrivaled high-efﬁciency drive.

The EEEngine’s energy-saver/low-heat-generation

design has reduced power consumption to 50% or

less, and reduced heat generation to 35% or less (in

ﬁeld applications, compared to Yamaha’s previous

models), and has lead to a reduction in energy cost

and to less-restrictive installation requirements related

to heat generation.

Contents

Introduction............................................................5

Features ................................................................5

EMX5000-20/EMX5000-12 Quick Guide ....................6

Front and rear panel..................................................10

Control panel.......................................................10

Input/output panel................................................16

Rear panel...........................................................18

Installation/Connections............................................19

Installation ...........................................................19

Connection ..........................................................19

Connecting input/output equipment.....................21

Basic operation .........................................................22

Connecting microphones and instruments..........22

Using the digital effect.........................................22

Example setups.........................................................24

As a conference/entertainment hall sound

system..............................................................24

As a band PA.......................................................26

Using a subwoofer...............................................28

Troubleshooting ........................................................29

Specifications............................................................30

General specifications.........................................30

Input specifications..............................................31

Output specifications...........................................31

Dimensions..........................................................32

Installing an optional rack mount kit ....................32

Block/Level Diagram............................................33

EMX5000-20/EMX5000-12 Quick Guide

EMX5000-20/EMX5000-12—Owner’s Manual

EMX5000-20/

EMX5000-12

Quick Guide

The following steps (1–5) explain the basic con-

nection and operation of the EMX5000-20/

EMX5000-12.

Also, please read “Front and Rear Panel” and

“Basic Operation” following this Quick Guide

section to learn more about using the EMX5000-

20/EMX5000-12.

Connection

Connecting speakers

Using speaker cables, connect each speaker to the

SPEAKERS A jack and to the B jack in the

SPEAKERS jack section on the rear panel of the

EMX5000-20/EMX5000-12.

• In the example shown by the above diagram, two

main speakers are connected (one each to left and

right) in stereo. For other connection examples,

refer to pages 20–21.

• You may connect to either of the two jacks on the

speakers.

• Be sure to use a cable designed for speaker connec-

tion.

• Speakers with a Speakon connector can also be con-

nected using a Speakon cable. In this case, use the

SPEAKERS 1 jacks to output the signal from the

EMX5000-20/EMX5000-12.

• When connecting a Speakon connector to the

EMX5000-20/EMX5000-12, be sure to turn the plug to

the right to lock the connection after inserting the plug.

Never connect the speakers in the manner shown

below. Otherwise, the EMX5000-20/EMX5000-

12’s built-in power ampliﬁer will be damaged.

Setting the power ampliﬁer mode

Set the power amp select switch (located on the

right corner on the panel) to ST L-R.

• This quick guide explains how to connect one main

speaker each to left and right for stereo operation. If

the power amp select switch is set to the ST L-R

position as shown here, the stereo R signal will be

output from the SPEAKERS A jacks, and the stereo

L signal from the SPEAKERS B jacks.

Refer to pages 14, 19, 20 for other connections and

power amp select switch settings.

STEP 1

EMX5000-20 (EMX5000-12)

Power amp select switch

EMX5000-20

(EMX5000-12)

EMX5000-20/EMX5000-12 Quick Guide

EMX5000-20/EMX5000-12—Owner’s Manual

Connecting a microphone

Make sure that the power is turned off to the

EMX5000-20/EMX5000-12.

Connect mics to channels 1–16 (EMX5000-20)

or 1–8 (EMX5000-12), using the INPUT A jacks

if the mic has an XLR plug, or the INPUT B jacks

if the mic has a phone plug.

Using a condenser microphone

Turn on the PHANTOM switch (located in the upper

center corner on the panel).

• The PHANTOM switch supplies phantom power to

all channel inputs at once (EMX5000-20: 1–8 and 9–

16, EMX5000-12: 1–8), so mics other than con-

denser mics must be connected to the INPUT B

jacks.

• Do not connect or disconnect a condenser micro-

phone while the power to the unit is on and the

PHANTOM switch has been turned on.

Connecting a CD player, MD player, and/or cassette

deck

Connect a CD player or MD player to the 2TR IN

jacks. Refer to the operation manual of the corre-

sponding device for more information on the

input and output of the device.

• To connect a second player, use the LINE jack.

• Connect a recorder to the REC OUT jacks.

Connecting an electric acoustic guitar or electric

bass

Connect electric/acoustic guitars or electric

basses via an effect processor or direct box to the

INPUT B jack.

• You cannot use the INPUT A jack and the INPUT B

jack for the same channel at the same time. If a

microphone has already been connected to the

INPUT B jack of a channel, you cannot connect the

effect unit to the INPUT A jack of the channel.

EMX5000-20 (EMX5000-12)

Microphone

EMX5000-20

(EMX5000-12)

PHANTOM switch

EMX5000-20

(EMX5000-12)

Recorder

(Cassette, DAT, MD)

CD player

EMX5000-20

(EMX5000-12)

Direct box

Effect unit

Electric-acoustic

guitar

Electric

bass

EMX5000-20/EMX5000-12 Quick Guide

EMX5000-20/EMX5000-12—Owner’s Manual

Connecting an electronic musical instrument

To the EMX5000-20/EMX5000-12’s LINE or ST

SUB IN jacks, you can connect an electronic

musical instrument such as a synthesizer, drum

machine, signal processor connected to an elec-

tric guitar, etc. Refer to the diagram below to

make a stereo connection from the output jacks

(such as L/MONO and R) of an electronic musi-

cal instrument to the LINE or ST SUB IN jacks in

stereo.

Power on

1 Turn on the power to all external devices con-

nected to the EMX5000-20/EMX5000-12.

2 Make sure that the ST OUT fader of the

EMX5000-20/EMX5000-12 is lowered, and then

press the POWER switch of the EMX5000-20/

EMX5000-12 to turn it on.

• Be sure to follow the power up sequence speciﬁed

above to prevent the speakers from being damaged.

• To correct the low range, turn on the YAMAHA

SPEAKER PROCESSING switch in the upper right

corner of the panel.

Sound output

Set the ST OUT fader and the input channel fad-

ers to the “–

∞

” position, and while playing the

instrument (or singing into the mic) connected

to the channel you want to check, raise the GAIN

control of the channel so that the PEAK indicator

of that channel lights occasionally.

• Do not press the 26dB PAD switch if sound is input

from the microphone. Otherwise, press the 26dB

PAD switch on.

Set the ST OUT fader to the “0” position, and

raise the faders of the input channels to adjust the

volume.

• Please be aware that if the PEAK indicator of the ST

level meter is continuously lit for an extended time,

the internal amp or the connected speakers may be

damaged.

EMX5000-20

(EMX5000-12)

Synthesizer,

Drum machine,

Guitar processor

STEP 2

EMX5000-20

(EMX5000-12)

STEP 3

EMX5000-20

(EMX5000-12)

EMX5000-20

(EMX5000-12)

EMX5000-20/EMX5000-12 Quick Guide

EMX5000-20/EMX5000-12—Owner’s Manual

Use the ST OUT fader to adjust the volume of the

speakers.

Applying built-in effects

1 Use the PROGRAM selector to select the type of

effect that you want to apply.

2 Turn on the ON switch in the EFFECT section.

The ON switch indicator lights up.

3 Set the EFFECT RTN fader to the “0” position.

4 If you want to use effect channel 1, adjust the

effect depth by turning the EFF1 control of the

channel to which you want to apply the effect.

Power off

1 Press the POWER switch of the EMX5000-20/

EMX5000-12 to turn off the power to the unit.

2 Turn off the power to all connected devices.

• Be sure to follow the power off sequence speciﬁed

above to prevent the speakers from being dam-

aged.

• In preparation for the next time you will use the

EMX5000-20/EMX5000-12, we recommend that

you set the faders of the EMX5000-20/EMX5000-

12 to the “–

∞

” position.

EMX5000-20

(EMX5000-12)

STEP 4

EMX5000-20

(EMX5000-12)

EMX5000-20

(EMX5000-12)

EMX5000-20

(EMX5000-12)

STEP 5

Front and rear panel

EMX5000-20/EMX5000-12—Owner’s Manual

Front and rear panel

Control panel

■

Channel control section

In this section, you can adjust equalization (fre-

quency response), volume level, effect and AUX

output levels for the input signal of each channel.

26 dB pad switch

This switch attenuates the input signal by 26 dB.

Attenuation is on when the switch is pressed

inward.

GAIN control

Use this knob to adjust the sensitivity according

to the input signal level, so that the input level is

appropriate.

For the best balance of S/N ratio and dynamic

range, adjust this knob so that the peak indicator

lights occasionally.

* When the knob is at the “ ” position, the input

sensitivity will be +4 dB.

(High pass ﬁlter) switch

This is an on/off switch for the high-pass ﬁlter.

The high-pass ﬁlter is on when the switch is

pressed inward, and the frequency region below

80 Hz will be attenuated at 18 dB/octave.

Equalizer controls (HIGH, MID, LOW)

This is a 3-band equalizer that adjusts the high

frequency range, mid frequency range, and low

frequency range of each channel.

When the HIGH and LOW knobs are in the “

▼

”

position, the high and low ranges will have a ﬂat

response. Turning a knob toward the right will

boost the corresponding frequency range, and

turning it toward the left will cut it.

For the mid range, use the upper MID knob to

specify the center frequency of the range, and use

the lower knob to set the amount of boost or cut

that will occur. The frequency response is ﬂat

when the lower knob is set to the “

▼

” position.

Turning the lower knob toward the right will

boost the corresponding frequency range, and

turning the knob toward the left will cut it.

The base frequency (or center frequency), range

of boost or cut, and equalizer type of each band

are as follows:

HIGH: 10kHz, ±15 dB, shelving type

MID: 250Hz–5kHz, ±15 dB, peaking type

LOW: 100Hz, ±15 dB, shelving type

Control panel

EMX5000-20/EMX5000-12—Owner’s Manual

AUX1, AUX2 controls / POST switches

These knobs adjust the level at which the input

signal will be sent to the AUX1 and 2 buses.

Nominal level is when the knob is set to the “

√

”

position. The position from which the signal is

sent can be set by the POST switch to either pre-

fader (before the channel fader

) or post-fader

(after the channel fader

). When the switch is

pressed inward, post-fader is selected.

The signal will be output from the AUX1 and 2

buses to the AUX SEND 1 and 2 jacks of the

input/output section, and can be sent to external

monitor amps or powered speakers.

EFF 1, 2 controls (EFFECT)

For each channel, these control the amount of

signal that is sent to the EFFECT 1, 2 buses.

The signal of the EFFECT 1, 2 buses is sent to the

EFFECT SEND 1, 2 jack (input/output panel

It is also sent to the built-in effect when the ON

switch

in the digital effect section is turned on.

PAN (panpot) control

(EMX5000-20: Channels 1–16,

EMX5000-12: Channels 1–8)

The PAN knobs set the stereo position of the sig-

nal that is sent to the STEREO bus. The signal is

located in the center when the knob is positioned

at “

▼

,” at right at R, and at left at L.

BAL (balance) control

(EMX5000-20: Channels 17/18–19/20,

EMX5000-12: Channels 9/10–11/12)

The BAL knobs set the balance between the left

and right channels, and assign the signals

received at inputs 17/18–19/20, 9/10–11/12 to the

STEREO bus.

ON switch, indicator

This is an on/off switch for the input signal of

each channel. The indicator will light if this

switch is turned on.

PEAK indicator

The indicator will light 3 dB before clipping,

warning that clipping level is near.

SIGNAL indicator

This indicator will light if a signal is being input

to the corresponding channel.

PFL (pre-fader listen) switch

Channels for which this switch is on will send a

signal from a post-EQ pre-fader location to the

PHONES jack (input/output panel

). Use this

when you wish to use the headphones to monitor

only a speciﬁc channel.

Channel fader

This controls the output level of the input chan-

nel signal.

D PHANTOM indicator

This will light when the PHANTOM switch

(input/output panel 3) is on.

■ Stereo sub input section

In this section, you can adjust the input level of

external equipment connected to the ST SUB IN

1, 2 jacks on the input/output panel.

E AUX 1, 2 controls

This knob adjusts the amount of the signal sent

from the ST SUB IN 1 and 2 jacks (input/output

panel 7) to the AUX 1, 2 buses.

F ST (stereo) control

The ST knob adjusts the amount of stereo signal

sent from the ST SUB IN 1 and 2 jacks to the

STEREO bus.

Note: The amount of signal that is sent to the

EFFECT 1, 2 bus from each channel will be af-

fected not only by the setting of the EFFECT 1,

2 control, but also by the setting of the channel

fader C (post-fader send).

Note: If this switch is turned on, you can mon-

itor a channel even if the channel fader is low-

ered, or if the ON switch is off. This will not

affect the signals that are sent to the STEREO

bus, AUX 1 and 2 buses, and EFFECT bus.

12 Front and rear panel

EMX5000-20/EMX5000-12—Owner’s Manual

G PFL (pre-fader listen) switch

When this switch is turned on, the signal at the

point before the ST control knob F is sent to the

PHONES jack (input/output panel D).

■ Master control section

In this section, you can adjust the ﬁnal level of

the outputs.

H AUX 1 fader

The AUX 1 fader adjusts the ﬁnal level of the sig-

nal sent from the AUX 1 bus to the AUX SEND 1

jack (input/output panel 8). If the Power amp

select switch Y is set to AUX 1-MONO, using

this fader enables you to adjust the level of the

signal sent from the SPEAKERS A 1/2 jacks to the

speakers.

I AUX 2 fader

The AUX 2 fader adjusts the ﬁnal level of the sig-

nal output from the AUX 2 bus to the AUX

SEND 2 jack (input/output panel 8). If the

Power amp select switch Y is set to AUX 1-

AUX 2, using this fader enables you to adjust the

level of the signal sent from the SPEAKERS B 1/2

jacks to the speakers.

J MONO OUT fader

The MONO OUT fader adjusts the ﬁnal level of

the monaural signal output from the STEREO

bus to the MONO OUT jack (input/output panel

C).

If the Power amp select switch Y is set to AUX 1-

MONO, this fader also adjusts the level of the sig-

nal sent from the SPEAKERS B 1/2 jacks to the

speakers.

If the Power amp select switch Y is set to MONO

BRIDGE, this fader adjusts the level of the signal

sent from the SPEAKERS A 1 jacks to the speaker.

K ST OUT fader

The ST OUT fader adjusts the ﬁnal level of the

signal sent from the STEREO bus to the ST OUT

jacks (input/output panel 0). If the Power amp

select switch Y is set to ST L-R, this fader also

adjusts the level of the signal sent to the SPEAK-

ERS jacks (rear panel 3).

L AFL (after fader listen) switch

When this switch is on, the output signal that

passes through the corresponding fader is sent to

the PHONES jack (input/output panel D). Use

these switches when you wish to monitor a par-

ticular output signal through the headphones.

■ 2TR IN section

In this section, you can adjust the input level of a

cassette deck or a CD player that is connected to

the 2TR IN jacks (input/output panel 5).

M ST (stereo) control

This knob adjusts the level of the signal sent from

the 2TR IN jacks to the STEREO bus.

N PFL (pre-fader listen) switch

When this switch is on, the signal input from the

2TR IN jacks is routed at the point before the ST

control M to the PHONES jack (input/output

panel D).

Note: The ST control setting does not affect

the level of the signal sent to the PFL/AFL buses

(pre-fader send).

H I J K

Note: The setting of this fader does not affect

the signal output from the STEREO bus to the

ST SUB OUT jacks.

Control panel 13

EMX5000-20/EMX5000-12—Owner’s Manual

■ Digital effect section

This section enables you to turn the built-in two-

channel digital effects on/off and select the effect

type.

O PROGRAM selector

This knob selects the effect type for the internal

digital effect.

P PARAMETER control

This knob adjusts the time parameter of the

internal digital effect.

Q AUX 1/2 control

This knob adjusts the level of the return signal

that is sent from the built-in digital effect to the

AUX 1/2 buses.

R TAP switch, indicator

Only if the PROGRAM selector has selected

TAP DELAY as the internal effect type, you can

press this switch to set the desired delay time.

Press the TAP switch several times, and the inter-

val between the last two presses will be set as the

delay time. The speciﬁed time will be remem-

bered even if the power is turned off.

The LED beside the switch will blink in synchro-

nization with the delay time only when the effect

type is TAP DELAY.

S EFFECT 1/2 ON switch

This switch turns the internal digital effect on/

off.

T PFL (Pre-fader listen) switch

When this switch is on, the signal from before the

EFFECT 1/2 RTN faders U will be sent to the

PHONES jack (input/output panel D).

U EFFECT 1/2 RTN fader

This fader adjusts the level of the return signal

that is sent from the built-in digital effect to the

STEREO bus.

14 Front and rear panel

EMX5000-20/EMX5000-12—Owner’s Manual

■ Graphic equalizer section

This section enables you to adjust the tone of the

STEREO bus signal.

V Graphic equalizer

This is a 9-band graphic equalizer that allows you

to adjust the frequency response of the STEREO

bus signal, providing a maximum of ±12 dB of

cut/boost for each frequency band.

This graphic equalizer affects both the STEREO

bus signal that is output to the speakers and the

line level signal that is output from the ST OUT

jacks (input/output panel 0), and MONO OUT

jack (input/output panel C).

W ON switch

This switch turns the graphic equalizer on/off.

■ Power amp section

This section allows you to select the signals that

will be sent to the built-in two-channel power

ampliﬁer.

X LIMITER indicator

This indicator lights up when the level of the sig-

nal output from the power amp section reaches

the maximum and the limiter is activated. Adjust

the ST OUT K and appropriate fader so that the

indicator lights up for only a short while when

the signal reaches the maximum level.

Y Power amp select switch

Select one of the following three settings to spec-

ify the signals to be routed to the corresponding

jacks according to the speaker connection at the

SPEAKERS jacks 3 on the rear panel.

• ST L-R

The STEREO bus signals are output from the

SPEAKERS A 1/2 jacks and the SPEAKERS B 1/2

jacks. The ﬁnal level of these signals is adjusted by

the master ST OUT fader.

• AUX 1-MONO

The AUX 1 bus signals are output from the

SPEAKERS A 1/2 jacks, and a monaural signal

that is a mix of the STEREO bus signals is output

from the SPEAKERS B 1/2 jacks. The ﬁnal level of

these signals is adjusted by the master AUX 1

fader and the MONO OUT fader.

• AUX 1-AUX 2

The AUX 1, 2 buses signals are output from the

SPEAKERS A 1/2 jacks and the SPEAKERS B 1/2

jacks.

• MONO BRIDGE

The monaural signal that is a mix of the STEREO

bus is output from the SPEAKERS A 1 jack. The

ﬁnal level of this signal is adjusted by the master

MONO OUT fader.

Set the switch to this position when you connect

only one speaker to play a loud sound.

Z Maximum output select switch

This switch lets you change the maximum output

level of the two internal power amps between

three levels.

Set this as appropriate for the size of the room or

the input capacity of the speakers.

• 500W + 500W

The two internal amps will produce a maximum

of 500W + 500W/4Ω.

• 300W + 300W

The two internal amps will produce a maximum

of 300W + 300W/4Ω.

• 100W + 100W

The two internal amps will produce a maximum

of 100W + 100W/4Ω.

Note: The indicator lights up or flashes for a

longer duration if the power amp section is sig-

nificantly overloaded, which could result in

malfunction. Avoid such a situation.

Control panel 15

EMX5000-20/EMX5000-12—Owner’s Manual

■ POWER indicator

[ POWER indicator

This indicator will light up when the power of the

EMX5000-20/EMX5000-12 is turned on.

■ YAMAHA SPEAKER PROCESSING

\ ON/OFF switch

This switch enables you to compensate the low

range of the speakers. The low range balance

when this switch is on varies depending on the

speakers.

First, check the low range balance by auditioning

the resultant sound, then set this switch to on or

off.

■ STAND-BY

] ON/OFF switch

This switch mutes (silences) the input signals

from channels 1–16 (EMX5000-20) or channels

1–8 (EMX5000-12). The indicator will blink

when this switch is on.

■ Other indicators and controls

^ Peak level indicator

This indicator allows you to monitor the level of

the signal output from the ST OUT jacks. The “0”

indicator lights up when the output level reaches

+4 dB.

a PHONES control

This knob adjusts the level of the signal moni-

tored via the PHONES jack (input/output panel

D).

b ST SUB OUT control

This knob adjusts the ﬁnal level of the signal sent

from the STEREO bus to the ST SUB OUT jacks

(input/output panel A).

c LPF control, ON/OFF switch

This switch applies a low-pass ﬁlter to the signal

that is output from the PFL/AFL bus to the

MONO OUT jack. The frequency is indicated by

the position of the slit in the control trimmer that

is set into the panel above the switch. To adjust

the frequency, use a slotted screwdriver to turn

the control to the desired position. This will out-

put the region below the frequency (80–120 Hz)

you specify by the control knob.

Use this when you are using a sub-woofer.

[

]

Note: The setting of this control does not affect

signals that are sent from the STEREO bus to

the ST SUB OUT jacks and the SPEAKERS

jacks.

16 Front and rear panel

EMX5000-20/EMX5000-12—Owner’s Manual

Input/output panel

1 Channel input jacks (INPUT A, INPUT B)

EMX5000-20: 1–16, EMX5000-12: 1–8

By using the GAIN control (control panel 2)

you can connect any of the jacks to a wide range

of sources, from mics to line-level devices

(including synthesizers and rhythm machines).

The INPUT A jacks can provide +48V phantom

power, allowing you to use condenser micro-

phones.

The nominal input level is from –16 dB to –60 dB

when the 26 dB pad switch (control panel 1) is

off, or from +10 dB to –34 dB when it is on.

Both INPUT A and B are balanced.

They are compatible with microphones of output

impedance 50–600Ω or line level devices of

600Ω.

Pin connections for the jacks are as follows:

* You can also connect a normal unbalanced phone plug.

2 INSERT I/O (insert) jacks

These are TRS phone jacks that enable you to

insert an external effect processor, such as a com-

pressor/limiter, between the equalizer and fader

of input channels. These connections require a

special “Y” cable, such as shown in the following

diagram. The nominal input/output levels are

0 dB.

A56 8

INPUT A jacks

(XLR type)

INPUT B jacks

(TRS phone jacks) *

Pin 1: ground Sleeve: ground

Pin 2: hot (+) Tip: hot (+)

Pin 3: cold (–) RIng: cold (–)

GND

RST

GND

Note: It is not possible to simultaneously use

both the INPUT A and B inputs of a given

channel. For each channel, use only one of the

inputs as appropriate for the input source.

Phantom power is switched on/off simulta-

neously for channels 1–8 and 9–16 (EMX5000-

20), 1–8 (EMX5000-12). For this reason, devic-

es (in particular, unbalanced devices) other

than condenser microphones must be connect-

ed to the INPUT B input jacks of channels or

channel 17/18–19/20 (EMX5000-20), 9/10–11/

12 (EMX5000-12) input jacks if the PHAN-

TOM +48V switch (control panel 3) is on.

to the input jack of

the external processor

to the output jack of

the external processor

to the INSERT I/O jack

Tip

Ring

Sleeve

Input/output panel 17

EMX5000-20/EMX5000-12—Owner’s Manual

3 PHANTOM switch

This is an on/off switch for the phantom power

supplied to the INPUT A jacks of channels 1–8

and 9–16 (on the EMX5000-20) or channels 1–8

(on the EMX5000-12). When this switch is on,

the indicator in the upper part of the control

panel will light.

4 LINE (stereo) input jacks

EMX5000-20: 17/18–19/20,

EMX5000-12: 9/10–11/12

These are the input jacks for channels 17/18–19/

20, 9/10–11/12 and are used to connect to the ste-

reo output jacks of electronic instruments, cas-

sette decks, or CD players.

You can connect either phone plugs or RCA

phono plugs, as appropriate for the type of jack

on the device you are connecting. The nominal

input level is from –34 dB to +10 dB.

5 2TR IN jacks

These are phono jacks that allow the signal from

an external device, such as a cassette deck and CD

player, to be added to the STEREO bus. The

nominal input level is –10 dBV.

6 REC OUT jacks

These phono jacks are used to connect to the

inputs of a recording device, such as a cassette

deck, to record the signal from the STEREO bus.

The nominal output level is –10 dBV.

7 ST SUB IN 1 (stereo sub 1) jacks

ST SUB IN 2 (stereo sub 2) jacks

These phone jacks are used to connect stereo out-

puts of a sub mixer or external effect processor.

The signal input here can be routed to the AUX 1

bus, AUX 2 bus, and STEREO bus. The nominal

input level is +4 dB.

8 AUX SEND 1 jack, AUX SEND 2 jack

These phone jacks output the line-level signals of

the AUX 1/2 buses. Connect stage-monitoring

ampliﬁers or powered speakers here. Use the

AUX 1 fader (control panel H) and the AUX 2

fader (control panel I) respectively to adjust the

ﬁnal level of the signals output from these jacks.

The nominal output level is +4 dB.

9 EFFECT SEND 1 jack, EFFECT SEND 2 jack

The input of an external effect unit such as a

delay or echo can be connected to this jack.

The signal adjusted by the EFF 1, 2 control of

each channel will be sent to the EFFECT 1, 2 bus,

and output from this jack.

The nominal output level is +4 dB.

0 ST OUT jacks

These phone jacks output the line level signal of

the STEREO bus. The ﬁnal output level from

these jacks is adjusted by the ST OUT fader (con-

trol panel K). The nominal output level is +4 dB.

A ST SUB OUT jacks

These phone jacks output the line-level signals of

the STEREO bus. Connect an external mixer or

additional PA system to these jacks.

Use the ST SUB OUT control (control panel b)

to adjust the ﬁnal output level at the ST SUB

OUT jacks.

The nominal output level is +4 dB.

B P.AMP IN A, B (power amp input) jacks

These phone jacks are used to input line-level ste-

reo signals to the two-channel built-in power

ampliﬁer. Connect an external mixer output here.

The nominal input level is +4 dB.

C MONO OUT jack

This phone jack mixes the STEREO bus signals

and output a monaural signal. Connect an addi-

tional PA system here. Use the MONO OUT

fader (control panel J) to adjust the ﬁnal level of

the signal output from this jack. The nominal

output level is +4 dB.

D PHONES jack

This is a stereo phone type output jack, and is

used to monitor the channels selected by the PFL

switches on the front panel and the buses selected

by the AFL switches.

The nominal output is 3mW when headphones

are connected.

E FOOT SW EFFECT 2 ON/OFF jack

A separately sold Yamaha FC5 foot switch can be

connected to this jack so you can use your foot to

switch the built-in digital EFFECT 2 on/off.

Note: The setting of the graphic equalizer or

ST OUT fader on the control panel does not af-

fect the signals output from these jacks. Adjust

the recording level on the recording device.

Note: Use only the L jack to connect a monau-

ral output device.

Note: If you insert a plug into this jack, the cor-

responding channel of the power amplifier will

be isolated, and no signals will be sent from the

mixer section.

18 Front and rear panel

EMX5000-20/EMX5000-12—Owner’s Manual

F FOOT SW (EFFECT 2) TAP jack

When TAP DELAY is selected as the internal

effect type for the EFFECT 2 RTN channel, you

can connect a separately sold FC5 foot switch to

this jack, and press the foot switch to set the delay

time to the corresponding interval. When you

press the foot switch several times, the delay time

will be set to the interval between the last two

presses.

G LAMP jack

This is an XLR (3-pin female) output jack that

supplies power to a lamp.

Rear panel

1 AC inlet

Connect the socket end of the included AC cable

to this inlet. Connect the plug end of the cable to

an AC outlet of the voltage printed below the

inlet.

2 POWER switch

This switch turns on/off the power to the

EMX5000-20/EMX5000-12.

3 SPEAKERS (speaker output) jacks

These jacks are used to connect speakers.

Jacks 1 are Speakon-type connectors. Jacks 2 are

1/4" phone jacks. The setting of the control panel

power amp select switch Y will determine the

signal that is output to these jacks, and the num-

ber and appropriate impedance of the speakers

that can be connected.

Note: Before you turn the power of the

EMX5000-20/EMX5000-12 on or off, the fad-

ers and controls in the master section of the

control panel must be lowered to the minimum

position.

Sidan laddas ...

Yamaha EMX 5000-20 Användarmanual

varumärke: Yamaha

Modell: EMX 5000-20

Kategori: Ljudmixer

Typ: Användarmanual

Denna manual är också lämplig för

Ladda ner pdf

Rapportera

på andra språk

italiano: Yamaha EMX 5000-20 Manuale utente
čeština: Yamaha EMX 5000-20 Uživatelský manuál
español: Yamaha EMX 5000-20 Manual de usuario
Deutsch: Yamaha EMX 5000-20 Benutzerhandbuch
polski: Yamaha EMX 5000-20 Instrukcja obsługi
português: Yamaha EMX 5000-20 Manual do usuário
français: Yamaha EMX 5000-20 Manuel utilisateur
Türkçe: Yamaha EMX 5000-20 Kullanım kılavuzu
English: Yamaha EMX 5000-20 User manual
dansk: Yamaha EMX 5000-20 Brugermanual
русский: Yamaha EMX 5000-20 Руководство пользователя
Nederlands: Yamaha EMX 5000-20 Handleiding
română: Yamaha EMX 5000-20 Manual de utilizare

Yamaha EMX 5000-20 Användarmanual

Denna manual är också lämplig för

Yamaha EMX 5000-20 Användarmanual

på andra språk

Relaterade papper

Andra dokument