Philips HQ8150/16 Användarmanual

HQ8150, HQ8142, HQ8140

ENGLISH 4

DANSK 15

 26

SUOMI

39

NORSK

50

SVENSKA

61

82

93

4

Important

Read this user manual carefully before you use the

appliance and save it for future reference.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

Children should be supervised to ensure that they

do not play with the appliance.

Only use the powerplug supplied.

The powerplug transforms 100-240 volts to a safe

low voltage of less than 24 volts.

The powerplug contains a transformer. Do not cut

off the powerplug to replace it with another plug,

as this causes a hazardous situation.

Do not use a damaged powerplug.

If the powerplug is damaged, always have it

replaced with one of the original type in order to

avoid a hazard.

Make sure the powerplug does not get wet.

Charge and store the appliance at a temperature

between 15°C and 35°C.

Never immerse the charging stand in water nor

rinse it under the tap.

Do not recharge the shaver in a closed pouch.

Always unplug the shaver before cleaning it under

the tap.

The shaver complies with the internationally

approved IEC safety regulations and can be safely

cleaned under the tap.

Be careful with hot water. Always check if the water

is not too hot, to prevent your hands from getting

burnt.

-

ENGLISH

This washable shaver is not suitable for shaving in

the shower.

Do not immerse the shaver in water.

Water may leak from the socket at the bottom

of the appliance, when you rinse it. This is normal

and not dangerous because all electronics are

enclosed in a sealed shell inside the shaver.



This Philips appliance complies with all standards

regarding electromagnetic elds (EMF). If handled

properly and according to the instructions in this

user manual, the appliance is safe to use based on

scientic evidence available today.

Charging

Make sure the appliance is switched off before you

start to charge it.

Charging takes approx. 1 hour.

You can also shave without charging by connecting

the shaver to the mains.



Charging

When the shaver is being charged, the charge

light burns green.



When the battery has been fully charged, the

top light ashes green.

-

,

ENGLISH 5



When the battery is running low, the bottom

light burns red.

When you switch the shaver off, this light ashes a

few times.



A fully charged shaver has a cordless shaving time of

up to 55 minutes.

Charging the appliance

HQ8150 only: Charge the shaver when the bottom

light burns red.

Do not recharge the shaver in a closed pouch.

1 Put the appliance plug in the shaver.

2 Put the powerplug in the wall socket.

3 Remove the powerplug from the wall socket

and pull the appliance plug out of the shaver

when the battery has been fully charged.



You can also charge the appliance by placing it in the

charging stand, if provided.

Place the shaver properly in the plugged-in

charging stand.

Lift the shaver from the stand without tilting it.

,

ENGLISH6





1 Switch on the shaver by pressing the on/off

button once.

The blue light ring around the on/off button goes

on to indicate that the motor is running.

2 Move the shaving heads quickly over your skin,

making both straight and circular movements.

Shaving on a dry face gives the best results.

Your skin may need 2 or 3 weeks to get

accustomed to the Philips shaving system.

3 Switch off the shaver by pressing the on/off

button once.

The blue light ring around the on/off button goes

out.

4 Clean the shaver (see chapter ‘Cleaning and

maintenance’).

5 Put the protection cap on the shaver every

time you have used it, to prevent damage.

Trimming

For grooming sideburns and moustache.

1 Open the trimmer by pushing the slide

downwards.

The trimmer can be activated while the motor is

running.

2 Close the trimmer (‘click’).

,

-

,

ENGLISH 7



Regular cleaning guarantees better shaving

performance.

The normal way to clean the appliance is to rinse

the shaving unit and the hair chamber with hot

water every time you have used the shaver.

Be careful with hot water. Always check if the

water is not too hot, to prevent your hands from

getting burnt.

Note: Water may leak from the socket at the bottom of

the appliance when you rinse it. This is normal and not

dangerous.



1 Switch off the shaver, remove the powerplug

from the wall socket and pull the appliance plug

out of the shaver.

2 Press the release button to open the shaving

unit.

3 Clean the shaving unit and the hair chamber by

rinsing them under a hot tap for some time.

Make sure you clean the inside as well as the

outside of the shaving unit.

4 Close the shaving unit and shake off excess

water.

Never dry the shaving unit with a towel or tissue,

as this may damage the shaving heads.

-

ENGLISH8

5 Open the shaving unit again and leave it open

to let the appliance dry completely.

You can also clean the hair chamber without water

by using the brush supplied.



1 Open the shaving unit, turn the lock

anticlockwise (1) and remove the retaining

frame (2).

2 Clean the cutters and guards with the brush

supplied.

Do not clean more than one cutter and guard

at a time, since they are all matching sets. If you

accidentally mix up the cutters and guards, it

may take several weeks before optimal shaving

performance is restored.

3 Put the shaving heads back into the shaving

unit. Put the retaining frame back into the

shaving unit and turn the lock clockwise.

4 Close the shaving unit.

Trimmer

Clean the trimmer every time you have used it.

1 Switch off the shaver, remove the powerplug

from the wall socket and pull the appliance plug

out of the shaver.

2 Clean the trimmer with the brush supplied.

ENGLISH 9

3 Lubricate the trimmer teeth with a drop of

sewing machine oil every six months.



You can clean the charging stand with a moist cloth.

Storage

1

Put the protection cap on the shaver to

prevent damage.

2 The appliance can be stored in the pouch

supplied.

3 The shaver can be stored in the charging stand,

if provided.

Replacement

Replace the shaving heads every two years for

optimal shaving results.

Replace damaged or worn shaving heads with HQ9

Philips shaving heads only.

Note: Do not mix up the cutters and the guards to

guarantee optimal shaving performance.

1 Switch the shaver off, remove the powerplug

from the wall socket and pull the appliance plug

out of the shaver.

ENGLISH10

2 Press the release button to open the shaving

unit.

3 Turn the lock anticlockwise (1) and remove the

retaining frame (2).

4 Remove the shaving heads and place new ones

in the shaving unit. Put the retaining frame

back into the shaving unit and turn the lock

clockwise.

Make sure that the projections of the shaving

heads t exactly into the recesses.

5 Close the shaving unit.



The following accessories are available:

HQ8500/HQ8000 powerplug.

HQ9 Philips Shaving Heads.

HQ110 Philips Shaving Head Cleaning Spray.

HQ8010 car cord.



Do not throw away the appliance with the normal

household waste at the end of its life, but hand

it in at an ofcial collection point for recycling. By

doing this, you help to preserve the environment.

The built-in rechargeable battery contains

substances that may pollute the environment.

Always remove the battery before you discard

and hand in the appliance at an ofcial collection

point. Dispose of the battery at an ofcial

collection point for batteries. If you have trouble

removing the battery, you can also take the

-

ENGLISH 11

appliance to a Philips service centre. The staff of

this centre will remove the battery for you and

will dispose of it in an environmentally safe way.



Only remove the battery if it is completely empty.

1 Remove the powerplug from the wall socket

and pull the appliance plug out of the shaver.

2 Let the shaver run until it stops and undo the

two screws at the back of the shaver.

3 Undo the two screws in the hair chamber.

4 Undo the three screws in the power unit.

5 Bend the 4 hooks aside (1) to take out the

power unit (2).

Be careful, the hooks are very sharp.

6 Remove the power unit cover by means of a

screwdriver.

7 Remove the battery.

Be careful, the battery strips are very sharp.

ENGLISH12

Do not connect the shaver to the mains again after

the battery has been removed.



If you need information or if you have a problem,

please visit the Philips website at www.philips.com

or contact the Philips Customer Care Centre

in your country (you nd its phone number in

the worldwide guarantee leaet). If there is no

Customer Care Centre in your country, go to

your local Philips dealer or contact the Service

Department of Philips Domestic Appliances and

Personal Care BV.



The shaving heads (cutters and guards) are not

covered by the terms of the international guarantee

because they are subject to wear.



1

Reduced shaving performance.

Cause 1: the shaving heads are dirty.The shaver

has not been rinsed long enough or the water

used was not hot enough.

Clean the shaver thoroughly before you continue

shaving. See chapter ‘Cleaning and maintenance’.

Cause 2: long hairs are obstructing the shaving

heads.

Clean the cutters and guards with the brush

supplied. See chapter ‘Cleaning and maintenance’,

section ‘Every six months: shaving heads’.

Cause 3: the shaving heads are damaged or worn.

Replace the shaving heads. See chapter

‘Replacement’.

-

ENGLISH 13

2 The shaver does not work when the on/off

button is pressed.

Cause 1: the battery is empty.

Recharge the battery. See chapter ‘Charging’.

Cause 2: the appliance is not connected to the

mains.

Put the powerplug in the wall socket.

3 The shaving unit has come off the shaver.

The shaving unit has not been placed correctly.

If the shaving unit becomes detached from the

shaver, you can easily put it back by inserting the

hinge into the slot in the rim of the hair chamber

and pushing it home until it locks into place

(‘click’).

-

ENGLISH14

Vigtigt

Læs denne brugsvejledning omhyggeligt igennem,

inden apparatet tages i brug, og gem den til

eventuelt senere brug.

Dette apparat er ikke beregnet til at blive brugt af

personer (herunder børn) med nedsatte fysiske

og mentale evner, nedsat følesans eller manglende

erfaring og viden, medmindre de er blevet vejledt

eller instrueret i apparatets anvendelse af en

person, der er ansvarlig for deres sikkerhed.

Apparatet bør holdes uden for børns rækkevidde

for at sikre, at de ikke kan komme til at lege med

det.

Brug kun det medfølgende netstik.

Net/transformerstikket omformer 100-240 Volt til

en lav sikkerhedsspænding under 24 Volt.

Netstikket indeholder en transformer. Derfor må

det aldrig klippes af og udskiftes med et andet stik,

da det vil resultere i en farlig situation.

Brug aldrig et beskadiget netstik.

Hvis netstikket beskadiges, må det kun udskiftes

med et originalt netstik af samme type for at

undgå enhver risiko ved efterfølgende brug.

Sørg for, at netstikket ikke bliver vådt.

Apparatet skal oplades og opbevares ved

temperaturer mellem 15° C og 35° C.

Opladeren må aldrig kommes ned i vand eller

skylles under vandhanen.

Shaveren må ikke oplades i et lukket etui.

Tag altid stikket ud af shaveren, inden den skylles

under vandhanen.

Produktet opfylder de internationalt godkendte

IEC-sikkerhedsregler og kan skylles under rindende

vand uden risiko.

-

DANSK 15

Vær forsigtig med varmt vand. Kontrollér altid, at

vandet ikke er for varmt, så du ikke skolder dine

hænder.

Denne vaskbare shaver er ikke beregnet til brug i

brusebadet.

Kom aldrig shaveren ned i vand.

Når shaveren rengøres, kan der dryppe lidt vand

ud af stikket i bunden af shaveren. Dette er helt

normalt og ganske ufarligt, da al elektronikken er

indkapslet i en forseglet skal inde i shaveren.



Dette Philips-apparat overholder alle standarder

for elektromagnetiske felter (EMF). Ved korrekt

anvendelse i overensstemmelse med instruktionerne

i denne brugsvejleding, er apparatet sikkert at

anvende, ifølge den videnskabelige viden, der er

tilgængelig i dag.



Kontrollér, at apparatet er slukket, før opladningen

påbegyndes.

En fuld opladning tager ca. 1 time.

Shaveren kan også anvendes uden opladning, blot

den tilsluttet en stikkontakt.





Når shaveren oplades, lyser opladeindikatoren

grønt.

-

,

DANSK16



Når batteriet er fuldt opladet, blinker den

øverste lysdiode grønt.



Når batteriet er ved at løbe tør for strøm, lyser

den nederste lysdiode rød.

Når du slukker for shaveren, blinker den et par

gange.



En fuldt opladet shaver giver en ledningsfri brugstid

på op til 55 minutter.



Kun HQ8150: Oplad shaveren, når den nederste

lysdiode lyser rødt.

Shaveren må ikke oplades i et lukket etui.

1 Sæt apparatstikket ind i shaveren.

2 Sæt netstikket i stikkontakten.

3 Så snart shaveren er ladet helt op, tages stikket

ud af stikkontakten og apparatstikket ud af

shaveren.



Hvis der medfølger en opladeenhed, kan shaveren

oplades i denne.

Placér shaveren korrekt i opladeren, som skal

være tilsluttet strøm.

,

DANSK 17

Løft shaveren op af opladeren uden at vippe den.





1 Shaveren tændes ved et enkelt tryk på on/off-

knappen.

Den blå lysring omkring on/off-knappen tænder

for at indikere, at motoren kører.

2 Bevæg skærene hurtigt hen over huden både i

lige strøg og i cirkelbevægelser.

Resultatet bliver bedst, hvis huden er tør.

Vær opmærksom på, at der kan gå 2-3 uger,

før din hud helt har vænnet sig til Philips’

barberingssystem.

3 Shaveren slukkes ved et enkelt tryk på on/off-

knappen.

Den blå lysring omkring on/off-knappen slukker.

4 Rengør shaveren (se afsnittet “Rengøring og

vedligeholdelse”).

5 Sæt altid beskyttelseskappen på shaveren efter

brug for at undgå beskadigelse.

,

-

,

DANSK18

Trimning

Til pleje af bakkenbarter og moustache.

1 Trimmeren åbnes ved at trykke skydekontakten

nedad.

Trimmeren kan aktiveres, mens shaveren kører.

2 Luk trimmeren med et klik.



Regelmæssig rengøring sikrer det bedste

barberingsresultat.

Apparatet rengøres normalt ved at skylle skærhoved

og skægkammer under rindende, varmt vand, hver

gang den har været brugt.

Vær forsigtig med varmt vand. Kontrollér altid, at

vandet ikke er for varmt, så du ikke skolder dine

hænder.

Bemærk: Der kan dryppe lidt vand ud gennem stikket

i bunden af shaveren, når du skyller den. Dette er helt

normalt og ganske ufarligt.



1 Sluk for shaveren, tag netstikket ud af

stikkontakten og apparatstikket ud af shaveren.

2 Tryk på udløserknappen og luk skærhovedet

op.

DANSK 19

3 Skyl skærhoved og skægkammer grundigt

under den varme hane.

Sørg for, at rengøre både inder- og ydersiden af

skærhovedet.

4 Luk skærhovedet, og ryst overskydende vand

væk.

Skærhovedet må ikke tørres med et håndklæde

eller køkkenrulle, da dette kan beskadige skærene.

5 Luk skærhovedet op igen - og lad det være

åbent - til shaveren er helt tør.

Skægkammeret kan også renses uden brug af vand

ved hjælp af den medfølgende børste.



1 Åbn skærhovedet, drej låsen venstre om (1) og

tag samlerammen af (2).

2 Rengør knive og lamelkapper med den

medfølgende børste.

Rens kun ét skær ad gangen, da knive og lamelkapper

er slebet parvis. Kommer man ved en fejltagelse til at

blande knive og lamelkapper, kan det tage ere uger,

før shaveren igen barberer optimalt.

-

DANSK20

3 Sæt skærene tilbage i skærhovedet. Sæt

samlerammen tilbage på plads og drej låsen

højre om.

4 Luk skærhovedet.

Trimmer

Rens trimmeren hver gang den har været brugt.

1 Sluk for shaveren, tag netstikket ud af

stikkontakten og apparatstikket ud af shaveren.

2 Rens trimmeren med den medfølgende børste.

3 Smør trimmerens tænder med en dråbe

symaskineolie hver 6. måned.



Opladeren kan rengøres med en fugtig klud.



1

Sæt beskyttelseskappen på shaveren, så den

ikke beskadiges.

2 Apparatet kan opbevares i den medfølgende

pung.

DANSK 21

3 Hvis der medfølger en opladerenhed, kan

shaveren opbevares i denne.



For til stadighed at opnå et optimalt

barberingsresultat anbefales det at udskifte skærene

hvert 2. år.

Beskadigede eller slidte skær må kun udskiftes med

HQ9 Philips skær.

Bemærk: For at bevare et optimalt barberingsresultat,

skal du passe på ikke at komme til at blande de

enkelte sæt af knive og lamelkapper.

1 Sluk for shaveren, tag netstikket ud af

stikkontakten og apparatstikket ud af shaveren.

2 Tryk på udløserknappen og luk skærhovedet

op.

3 Drej låsen venstre om (1) og tag samlerammen

af (2).

4 Tag skærene ud og sæt de nye i. Sæt

samlerammen tilbage i skærhovedet og drej

låsen højre om..

Sørg for, at de små tappe passer præcist ned i

recesserne.

5 Luk skærhovedet.



Der ndes følgende tilbehør:

HQ8500/HQ8000 netstik-

DANSK22

Sidan laddas ...

Philips HQ8150/16 Användarmanual

Denna manual är också lämplig för

Philips HQ8150/16 Användarmanual

på andra språk

Relaterade papper