Electrolux EXH09HX1WI Användarmanual

installation manual

Installationsvejledning

Asennusohje

Installasjonshåndbok

Installationsmanual

Heatpump

Varmepumpe

Ilmapumppu

Varmepumpe

Värmepump

EXH09HX/EXH09HX

EXH12HX/EXH12HX

Heatpump

Important! Carefully read and follow these

instructions for smooth and trouble-free

installation.

Caution! This room Heatpump uses

new refrigerant R410A.

1. Keep any open ends of pipes be

sealed with a cap, etc. until connec-

ted with the equipment.

2. Exercise great care when performing

piping installation so as water, dust,

etc. will not enter into the piping and

equipment.

3. Pipes connected to the indoor and

outdoor units must be used new.

(This Heatpump using R410A incurs

pressure higher compared with R22,

it is necessary to choose adequate

materials.)

4. Use only R410A refrigerant when

charging additional refrigerant to the

equipment. Never add lubricating oil

to the equipment in any case.

5. In order to prevent any other refrig-

erant from being charged acciden-

tally, the service port diameter of the

3-way valve has been changed. (1/2”

UNF screw)

Accessories

Items Q'ty Application

1

Mounting plate

1 To mount the indoor unit on the wall.

2

Wall plug

8 To fix the mounting plate with the long screws. To fix the

remote control with the special screw.

3

Long screw

7 To fix the mounting plate with the wall plugs.

4

Remote control

1 To control remotely.

5

Dry battery

2 For the remote control. AAA batteries.

6

Special screw

1 To mount the remote control on the wall.

7

Short screw

1 To fix the CORD HOLDER.

2 electrolux

Items Q'ty Application

8

Cord holder

1 To secure the electrical cable.

9

Manuals

OPER

INSTALL

1 Installation manual

1 Operation manual

10

Air purifying filter

2 To remove dust and tobacco smoke from the air.

Notes on locations

Important! Keep the following points in mind

and get the customer's approval.

Indoor unit

1. Keep the air outlet clear of any obstacle

so that outgoing air flows smoothly in the

entire room.

2. Make a drain hose hole for easy drainage.

3. Provide sufficient space on both sides

and above the unit.

4. The air filters should be easily taken in and

out.

5. Keep TV set, radio and the like 1 m or

more away from the unit and the remote

control.

6. Keep the air inlet clear of obstacles that

could block incoming air.

7. The remote control may not function

properly in a room equipped with an elec-

tronic simultaneous-start or rapid-start

fluorescent lighting.

8. Select a location that does not cause loud

operation noise and extreme vibrations.

Outdoor unit

1. Place the outdoor unit on a stable base.

2. Provided sufficient space around the

unit. It should also be well ventilated.

3. The unit should not be exposed to strong

wind nor splashed with rain water.

4. Water drain from the unit should be let

out without problem. Lay a drain hose if

required. In cold regions, installation of

the drain pipe is not advisable as freezing

could result.

5. Keep TV set, radio and the like 1 m or

more away from the unit.

6. Avoid locations exposed to machine oil

vapor, salty air (facing the seashore, for

example), hot spring vapor sulfur gas,

etc. Such location can cause break-

down.

7. Also, avoid locations exposed to muddy

water (along a road, for example) or

where the unit can be tampered with.

8. Select a location where the outgoing air

or operating noise cannot annoy others.

9. Install the unit on a stable base not to al-

low louder noise.

10. Keep the air outlet opening free of any

obstacle. This could affect the perform-

ance of the unit and create loud noises.

Piping

1. Piping length should be 1m or more in

order to decrease vibration propagated

from the outdoor unit.

2. If piping length exceeds 10m, add 20g of

refrigerant per 1m.

3. When the outdoor unit is placed at a high-

er level than the indoor units, provide a

trap near the hose’s lead-in port.

A

B

1

2

3

A) Max. piping length 15m

B) Max. level difference 7m

1 Indoor unit

2 Outdoor unit

3 Trap

electrolux 3

Locations of indoor and outdoor unit

min. 200

min. 50

min. 70

min. 100

4

Length unit: mm

Provide as much installation space as possi-

ble for efficient functioning.

Notes on drain hose

The drain hose can be connected at

either side of the indoor unit.

The unit has been shipped with the drain

hose connected at left (viewed from the back

of the unit) and the drain cap applied at right.

1

2

1 Drain hose

2 Drain cap

Reposition the drain hose and drain cap as

required.

1. Remove the fixed screw in the hose hold-

er at the end of the drain hose.

2. Hold the end of the drain hose, and pull it

out.

3. Pull out the drain cap.

4. Reconnect the drain hose to the right and

insert the drain cap to the left.

Fully insert the drain hose until it stops

and use the screw that was previously

removed in STEP (1) to secure the hose

holder to the drain pan.

Insert a hexagon socket screw key (4mm

diagonal) into the drain cap, and press it

fully.

1

3

4

2

1

2

3

4

5

1 Screw

2 Hose holder

3 Drain hose

4 Drain cap

5 Hexagon socket screw key

Caution! After replacing, make sure that

both the drain hose and drain cap are

firmly inserted.

Outdoor unit mounting screw holes

540

299

4 electrolux

Opening/closing open panel

To open, hold the left and right bottom cor-

ners of the panel and lift it up.

To close, press-fit the arrow-marked points.

Detaching the front panel

For servicing, for example, detach the front

panel in the following steps. Be sure to dis-

connect the power cord from the wall outlet

or turn off the circuit breaker.

1. Remove the air filter.

2. Unscrew the 2 screws of the front panel.

3. Open the vertical adjustment louver by

hand.

4. Remove the front panel.

– Slightly open the lower part of the front

panel, and extract the 5 hooks along

the upper surface for disassembly.

5. To set the panel back into position,

press-fit it at the bottom first and then

press its top.

1

2

3

1

2

3

4

1 Screw

2 Vertical adjustment louver

3 Air filter

Placing the mounting plate and making

a tube hole

Important! Fix the mounting plate

horizontally.

872

108

A

131

J

181

115

I

F

E

D

J

E

A

F

I

D

292

45

30

1 2 3

4

5

1. Referring to the figure above, mark the

location for the wall plugs and the tube

hole.

Length unit: mm

1 Center of wall hole: Leftward piping.

2 Outline of indoor unit

3 Center of wall hole: Backward piping

4 Ceiling

5 unit size

2. Drill diameter 6.5mm, depth 32mm holes

and fit the wall plug.

32 mm

6,5 mm

2

3. Secure mounting plate and check the

stiffness. Refer to figure at right for fixing

hole locations on mounting plate. Fix

mounting plate to wall at 7 points. Rec-

ommended fixing holes are marked in

circle around the hole.

electrolux 5

2

13

4. Drill a piping hole with 70mm diameter

concrete drill or a hole saw with a 5mm

down ward slant to the outside.

5 mm

1 2

3

5

4

1 Indoor

2 Outdoor

3 Cut with a saw

4 Cap (Downward to outdoor)

5 Sleeve

5. Set the sleeve and caps.

Setting up the indoor unit

Piping route

For directions 1 and 3, cut out the specific

zone without leaving any sharp edge.

(Keep the cut-out plate for possible future

use.)

1

2

3

1

3

2

1 Cut the plate along notch

2 Cut-out

3 Notch

Mounting the indoor unit

If the wall is 250 mm or thicker, connect the

pipes first.

1. For rear exit piping, pass the auxiliary pipe

and the drain hose through the piping

hole, and hook the unit onto the mounting

plate.

2. Push the unit and apply the bottom hook-

ing points to the mounting plate's sup-

port. (Take this step after cabling be-

tween the indoor and outdoor units.)

3. Pull the bottom of the unit to check that

the unit is fixed in place.

6 electrolux

1

1 Taping

Detaching the unit from the mounting

plate

Push the “

“ marks at the bottom of the in-

door unit and pull the bottom of the unit.

When the hooks are released from the

mounting plate, support the bottom of the

unit and lift the unit upwards.

Horizontal Piping

1. Reverse the positions of the drain hose

and drain cap. Refer to Notes on drain

hose.

1

2

1 Drain cap

2 Drain hose

2. Connect the pipes and coil tape around

the pipes and electrical cable.

21

1 Unit

2 Piping holder

3. Store the pipes within the back cavity of

the unit, and secure the pipes by attach-

ing the piping holder. (Refer to steps a)

and b) as shown below.)

a) Insert the top of the piping holder into

the square opening.

1

2

3

4

1 Unit

2 Tape

3 Piping holder

4 Insert

b) Hook the bottom of piping holder to

the unit.

electrolux 7

1

2

1 Unit

2 Hook

4. Coil tape around the drain hose together

with the pipes and electrical cable.

5. Hook the unit onto the mounting plate.

Connecting the electrical cable to the

indoor unit

1. Process the end of the electrical cable for

the indoor side.

– Use a copper cable. (Cross-section

area 2mm² or more)

– Use a cable which is not lighter than

polychloroprene sheathed flexible cord

(design 245 IEC 57).

8mm

40mm

2. Open the open panel by about 70°.

3. Connect the electrical cable.

– Be very careful not to confuse the ter-

minal connections. Wrong cabling may

damage the internal control circuit.

– The markings on the indoor unit’s ter-

minal board must match with those of

the outdoor unit.

1N2

7

8

1

2

3

1 Earth wire

2 Electrical cable

3 Terminal board

4. Fix the cable with the accompanying cord

holder and the short screw.

5. Close the open panel.

Connecting the drain hose

Indoor unit

1. Connect a drain hose.

2. Tape over the connecting part.

1

ø 18mm

1 Drain hose

8 electrolux

• Be sure to lay the drain hose downward for

smooth drainflow.

1

2

1 No trap allowed

2 Not to rise

• Be careful not to allow the drain hose to

rise, form a trap or leave its end in water,

as shown below.

1

2

3

1 Not running wavy

2 No trap allowed

3 Not left in water

• Coil thermal insulation around a drain hose

extension, if running in the room.

• It is recommended to add an "intermediate

air vent" when the drain hose is extended

horizontally, or an "anti-back-flow air vent"

when the hose is exposed to high winds

on a high-rise building, for example. For

this purpose, employ a "T tube joint" (PVC-

made, commercially available) halfway in

the hose.

2

1

1 To drainage pit

2 Air vent (T tube joint)

Connecting the refrigerant pipes

• Use pipes with thickness 0.8mm.

• Connect the pipes for the indoor unit first

and then for the outdoor unit.

• Bend the pipes carefully as not to damage

them.

• Do not over tighten the tubes; it may be

deformed or damaged.

Use a torque wrench, when possible. See

the table below for the flare nut tightening

torque.

Flare nut tightening torque

Tube size Torque

Liquid side 1/4" 16±2N·m (1.6±0.2kgf·m)

Gas side 3/8" 38±4N·m (3.8±0.4kgf·m)

Flaring the pipe end

1. Cutting with a pipe cutter

Cut at a right angle.

2. Deburring

Allow no cuttings in the pipe.

3. Putting in the flare nut

4. Flaring

Flare processing dimensions (A) differ ac-

cording to the type of flare tool.

electrolux 9

A

R410A tool: 0-0.5mm

Conventional tool: 1.0-1.5mm

5. Checking

To be flared perfectly circular.

Flare nut not missing.

Connecting the pipes

1. Tighten the flare nuts by hand for the first

3-4 turns.

2. Use two wrenches to tighten up the

pipes.

1

2

1 Flare body

2 Flare nut

3. Wind coating tape around refrigerant

pipes together with drain hose and elec-

trical cable for general.

1

1 Coating tape

– Lay the drain hose below the pipes.

– The thermal insulation should cover

both the GAS and LIQUID pipes as

shown below. As insulation, use poly-

ethylene foam 6 mm or thicker.

2

1

3

4

5

1 Gas

2 Insulation

3 Liquid

4 Drain hose

5 Electrical cable

1

1 1

2 2 2

3

3 3

OK OK OK

1 Gas

2 Liquid

3 Insulation

Air removal

Use an adapter for preventing vacuum pump

oil from flowing back to the gauge manifold

hose.

ON/OFF operation of the vacuum pump

should be made by the adapter switch.

1. Remove both valve shaft caps of the 2

and 3-way valves.

2. Remove the service port cap of the 3-

way valve.

3. Connect the gauge manifold hose to the

service port and the vacuum pump.

Be sure that the hose end to be connec-

ted to the service port has a valve core

pusher.

4. Open the gauge manifold valve and op-

erate the vacuum pump for 10-15 mi-

nutes.

Make sure the compound gauge reads

-76cmHg.

5. Close the gauge manifold valve.

6. Turn off the vacuum pump.

7. Fully open the 2-way valve with hexagon

socket screw key. (diagonally 4 mm)

Turn all the way up to contact.

10 electrolux

8. Fully open the 3-way valve with hexagon

socket screw key. Turn all the way up to

contact.

9. Disconnect the gauge manifold hose

from the service port.

10. Replace the service port cap and both

valve shaft caps tightly.

• Use a gauge manifold and hoses exclusive

for R410A.

• After air removal, check the tube connec-

tions for gas leak using a leakage detector

or soapy water. Regarding leakage detec-

tor, use high-sensitivity type designed spe-

cially for R410A.

1 Valve shaft cap

2 Hexagon socket screw key

3 2 - way valve

4 Service port cap

5 Vacuum pump

6 Vacuum pump adapter

7 Gauge manifold

8 Compound gauge

9 Valve shaft cap

10 3 - way valve

11 Indoor unit

Lo

Hi

1

2

3

4

5

6

7

9

10

11

8

7

3

9

2

10

4

6

4

5

1

10

1

8

10

Valve shaft cap tightening torque

Pipe size Width Torque

Liquid side 1/4" 22mm 24±3N·m

(2.4±0.3kgf·m)

Gas side 3/8" 22mm 24±3N·m

(2.4±0.3kgf·m)

Service port cap tightening torque

Torque

11±1N·m (1.1±0.1kgf·m)

Pump down

(Pump down is adopted in the case of

unit removal for re-installation, aban-

donment, repair etc.)

Pump down is to collect the refrigerant into

the outdoor unit by control of the 2 and 3-

way valves and the compressor.

1. Stop the Heatpump operation.

2. Remove both valve shaft caps of the 2

and 3-way valves.

3. Run the Heatpump at cooling test run

mode (Refer to TEST RUN). If pump

down is performed at normal cooling op-

eration, the protection system may en-

gage and stop the operation.

electrolux 11

4. After 5~10 minutes, fully close the 2-way

valve by turning the hexagon socket

screw key clockwise.

5. After 2~3 minutes, immediately close the

3-way valve fully.

6. Stop the test run operation.

7. Replace both valve shaft caps tightly.

8. Disconnect both refrigerant pipes.

• Do not perform the pump down when at

heating mode. The refrigerant will not be

collected.

Connecting the electrical cable to the

outdoor unit

1. Process the end of the electrical cable for

the outdoor unit.

8mm

40mm

2. Remove the control box cover.

3. Remove the cable holder and connect

the cable.

Be sure that the terminal connections are

as specified.

4. Fix the electrical cable sheath with the

cable holder and the screw.

5. Double-check that the cable is securely

in place.

6. Place the control box cover back in the

reverse order.

1

2

3

4

5

6

2

N 1

1 Earth wire

2 Terminal board

3 Cable holder

4 Electrical cable

5 Control box cover

6 Screw

Caution!

• Use the specified electrical cable.

Make sure the cable is secured in

place and that the terminals are free of

any excess force from the cable. Oth-

erwise overheating or fire may result.

• Dress the cable so that the control box

cover, the cord holder and cable hold-

er are not loose. Double-check that

the cover is tight in position. Other-

wise overheating, fire or electric shock

may result.

• Be sure to put the cable leads deep

into the terminal board and tighten up

the screws. Poor contact can cause

overheating or fire, or malfunction.

Power cabling

Prepare a dedicated power supply circuit.

For the connections, see below.

Supply power 220-240V, single-phase

Circuit breaker 10A (EXH09HX)

15A (EXH12HX)

12 electrolux

1

2

3

A

B

C

Power supply cable Power supply

A Blue Neutral

B Brown Live

C Green/yellow-striped Ground

• The appliance shall be installed in accord-

ance with national wiring regulations.

Wrong connection can cause overheating

or fire.

• Fit a disconnect switch, having a contact

separation of at least 3mm in all poles, to

the electricity power line.

Earth leakage breaker

• Provide an earth leakage breaker in order

to protect against electric shock in case of

leak.

• Use the current-activated, high-sensitivity,

high-speed type breaker with a rated sen-

sitivity current of below 30 mA and an

operating time of below 0.1 second.

Hanging the remote control

1. Fit the special screw to the wall with the

wall plug.

2. Hang the remote control to the screw

head.

2 6

1

1 Remote control rear side

Loading the batteries

Slide the cover in the direction of the arrow.

1. Open the cover.

2. Insert the batteries.

3. Close the cover.

– If after battery replacement the control

fails to function, take out the batteries.

Wait for more than 30 seconds and put

them in again.

Test run

1. Open the open panel to see the control

section.

2. Start the operation with the remote con-

trol.

3. Press the “AUX” button on the unit for 5

seconds or more.

electrolux 13

A beep sound is heard and the OPERA-

TION lamp starts flashing. Now the sys-

tem is in the cooling test run mode.

4. To put the system in the heating test run

mode, start the cooling operation and se-

lect the heating mode on the remote con-

trol.

5. Make sure the system runs well, and

press the AUX button again to stop the

operation.

Explanation to Customer

• Explain to the customer how to use and

maintain the system, referring to the oper-

ation manual.

• Ask the customer to carefully read the op-

eration manual.

• When the system has been set up, hand

the installation manual to the customer.

Important! Important points to explain

Whipping sound :

• The system adjusts itself, by expansion or

shrinkage, according to great temperature

fluctuations.

Running liquid sound :

• The refrigerant runs in the system, gener-

ating such sound. (For details, refer to the

accompanying operation manual.)

14 electrolux

Varmepumpe

Vigtigt Læs denne vejledning grundigt. Den

sikrer, at installationen forløber glat og uden

problemer.

Bemærk Denne varmepumpe til

rumopvarmning anvender et nyt

kølemiddel, R410A.

1. Evt. åbne slangeender skal proppes

til, indtil de sluttes til enheden.

2. Vær meget omhyggelig, når rørførin-

gen udføres, så der ikke kommer

vand, støv og lign. ind i rør og anlæg.

3. Der skal anvendes nye rør til tilslut-

ningerne på ude- og indeenheden.

(Da varmepumpen bruger R410A

som kølemiddel, udsættes den for

højere driftstryk end med R22, og det

skal der tages højde for ved materi-

alevalget).

4. Brug kun R410A-kølemiddel, når der

efterfyldes kølemiddel på anlægget.

Smør aldrig anlægget med smøre-

olie.

5. Diameteren på 3-vejsventilens drifts-

indgang er ændret for at sikre, at der

ikke utilsigtet kan påfyldes et andet

kølemiddel. (1/2" UNF-skrue)

Tilbehør

Betegnelse Antal Anvendelse

1

Monteringsplade

1 Til vægmontering af indeenhed.

2

Rawlplug

8 Til fastgørelse af monteringspladen med de lange skruer.

Til fastgørelse af fjernbetjening med specialskrue.

3

Lang skrue

7 Til fastgørelse af monteringspladen med rawlpluggene.

4

Fjernbetjening

1 Til fjernstyret betjening.

5

Batteri

2 Til fjernbetjeningen. AAA-batterier.

6

Specialskrue

1 Til vægmontering af fjernbetjening.

7

Kort skrue

1 Til fastgørelse af KABELKLEMME.

electrolux 15

Betegnelse Antal Anvendelse

8

Kabelklemme

1 Til fastgørelse af netkablet.

9

Vejledninger

OPER

INSTALL

1 Installationsvejledning

1 Betjeningsvejledning

10

Luftrensningsfilter

2 Til at fjerne støv og tobak fra luften.

Bemærkninger om placering

Vigtigt Husk på følgende, og spørg kunden

om lov.

Indeenhed

1. Hold luftudblæsningen fri for forhindrin-

ger, så den udgående luft uhindret kan

sendes rundt i hele rummet.

2. Lav et hul til afløbsslange, for nem aftap-

ning.

3. Sørg for, at der er god plads på begge

sider og over enheden.

4. Det skal være let at komme til at tage luft-

filtrene ud og sætte dem i.

5. Hold tv-apparat, radio og lign. mindst 1

meter fra enheden og fjernbetjeningen.

6. Sørg for, at der ikke står noget i vejen for

luftindsugningen, så indtaget blokeres.

7. Hvis der findes lamper med fluoresceren-

de lys i rummet, virker fjernbetjeningen

muligvis ikke, som den skal.

8. Vælg en placering, der ikke giver kraftige

støjgener og vibrationer under drift.

Udeenhed

1. Sæt udeenheden på et stabilt underlag.

2. Sørg for god plads rundt om enheden.

Der skal også være god lufttilførsel.

3. Enheden må ikke udsættes for kraftig

blæst eller sprøjt fra regnvand.

4. Det skal være let at komme til enhedens

vandafløb. Læg evt. en afløbsslange. I

kolde egne frarådes det at installere et

afløbsrør, da det vil kunne fryse til.

5. Hold en afstand på mindst 1 meter til tv-

apparat, radio og lign.

6. Undgå placeringer, hvor enheden ud-

sættes for dampe fra motorolie, salthol-

dig luft (f.eks. ved kysten), svovlgas fra

varme kilder og lign. På sådanne place-

ringer kan enheden bryde sammen.

7. Undgå også placeringer, hvor enheden

udsættes for mudret vand (f.eks. langs

en vej), eller hvor nogen kan komme til at

pille ved den.

8. Vælg en placering, hvor udblæsningsluft

eller driftsstøj ikke kan genere naboer.

9. Installer enheden på et stabilt underlag,

der ikke forstærker støjen.

10. Hold luftudblæsningen fri for forhindrin-

ger af enhver art. De vil kunne påvirke

enhedens ydelse og give kraftig støj.

Rørføring

1. Rørlængden skal mindst være 1 meter for

at mindske de vibrationer, der forplanter

sig fra udeenheden.

2. Hvis rørlængden er over 10 meter, tilsæt-

tes 20 g kølemiddel pr. løbende meter.

3. Hvis udeenheden placeres højere end in-

deenhederne, skal der være en vandlås

tæt ved slangens indføringsåbning.

A

B

1

2

3

A) Maks. rørlængde: 15 meter

B) Maks. niveauforskel: 7 meter

1 Indeenhed

2 Udeenhed

3 Vandlås

16 electrolux

Placering af inde- og udeenhed

min. 200

min. 50

min. 70

min. 100

4

Længdeenhed: mm

Sørg for at give installationen så meget plads

som muligt for at sikre effektiv funktion.

Bemærkninger om afløbsslange

Afløbsslangen kan tilsluttes på beg-

ge sider af indeenheden.

Enheden leveres med afløbsslangen tilsluttet

til venstre (set fra enhedens bagside) og med

afløbsproppen til højre.

1

2

1 Afløbsslange

2 Afløbsprop

Omplacér afløbsslange og afløbsprop, hvis

det er nødvendigt.

1. Fjern den faste skrue i slangeholderen i

enden af afløbsslangen.

2. Hold fast i enden af afløbsslangen, og

træk den ud.

3. Træk afløbsproppen ud.

4. Tilslut afløbsslangen til højre, og sæt af-

løbsproppen i på venstre side.

Sæt afløbsslangen så langt ind, som den

kan komme, og spænd slangeholderen

fast på bundkarret med den skrue, der

blev taget ud under TRIN (1).

Sæt en unbrakonøgle (4 mm diameter) i

afløbsproppen, og tryk den helt ind.

1

3

4

2

1

2

3

4

5

1 Skrue

2 Slangeholder

3 Afløbsslange

4 Afløbsprop

5 Unbrakonøgle

Bemærk Kontroller efter montering af

afløbsslange og afløbsprop, at de sidder

helt fast.

Skruehuller til montering af udeenhed

540

299

electrolux 17

Åbne/lukke adgangspanel

Panelet åbnes ved at holde i nederste højre

og venstre hjørne og løfte det op.

Panelet lukkes ved at trykke det på plads på

de steder, der er markeret med pile.

Aftagning af frontpanel

Til service og lign. afmonteres frontpanelet

som beskrevet nedenfor. Sørg for at tage

stikket ud af kontakten eller afbryde på ejen-

dommens el-tavle.

1. Fjern luftfilteret.

2. Skru de 2 skruer i frontpanelet ud.

3. Åbn med hånden spjældet til lodret juste-

ring.

4. Fjern frontpanelet.

– Åbn frontpanelets nederste kant lidt,

og træk de 5 kroge langs overkanten

ud, så panelet kan tages af.

5. Panelet monteres igen ved at først at tryk-

ke det på plads langs underkanten og

derefter trykke foroven.

1

2

3

1

2

3

4

1 Skrue

2 Spjæld til lodret justering

3 Luftfilter

Placering af monteringsplade og hul til

rørføring

Vigtigt Fastgør monteringspladen vandret.

872

108

A

131

J

181

115

I

F

E

D

J

E

A

F

I

D

292

45

30

1 2 3

4

5

1. Markér placeringen af rawlpluggene og

hullet til rørføringen som vist på ovenstå-

ende tegning.

Længdeenhed: mm

1 Centrum, hul i væg: Rørføring til ven-

stre.

2 Omrids, indeenhed

3 Centrum, hul i væg: Rørføring bagud

4 Maks.

5 enhedens størrelse

2. Bordiameter 6,5 mm, 32 mm dybe huller.

Sæt rawlplugs i.

32 mm

6,5 mm

2

3. Spænd monteringspladen fast, og mærk

efter, at den ikke giver sig. Hullernes pla-

cering på monteringspladen er vist på

tegningen til højre. Fastgør monterings-

pladen i væggen i 7 punkter. Anbefalede

monteringshuller er markeret med en cir-

kel om hullet.

18 electrolux

2

13

4. Bor hul til rørgennemføring med et 70 mm

murbor eller en hulsav, med 5 mm fald

mod ydersiden.

5 mm

1 2

3

5

4

1 Inde

2 Ude

3 Skær til med sav

4 Prop (med fald udefter)

5 Muffe

5. Påsæt muffe og propper.

Opsætning af indeenhed

Rørføring

Til retningerne 1 og 3 udskæres det pågæl-

dende område uden skarpe kanter.

(Gem det afskårne stykke til evt. senere

brug).

1

2

3

1

3

2

1 Skær pladen langs rillen

2 Afskæring

3 Rille

Montering af indeenhed

Hvis væggen er 250 mm tyk eller derover, til-

sluttes rørene først.

1. Ved afgang bagtil sættes forlængerrøret

og afløbsslangen gennem rørgennemfø-

ringen, og enheden hægtes på monte-

ringspladen.

2. Tryk på enheden, og sæt den fast på

monteringspladen ved at klemme den ind

over krogene nederst på monteringspla-

den. (Det gøres først, når ledningsførin-

gen mellem inde- og udeenhed er fær-

dig).

3. Træk i underkanten af enheden for at sik-

re, at den sidder helt fast.

electrolux 19

1

1 Bevikling

Afmontering af enhed fra monterings-

pladen

Tryk på "

"-markeringerne nederst på in-

deenheden, og træk i enhedens underkant.

Når krogene slipper monteringspladen, un-

derstøttes enheden nedefra og løftes opad.

Vandret rørføring

1. Byt om på placeringen af afløbsslange og

afløbsprop. Se under Bemærkninger til

afløbsslange.

1

2

1 Afløbsprop

2 Afløbsslange

2. Tilslut rørene, og vikl tape rundt om røre-

ne og elkablet.

21

1 Enhed

2 Rørholder

3. Gem rørene i hulrummet bag i enheden,

og sæt dem fast med rørholderen. (Se trin

a) og b) nedenfor).

a) Sæt toppen af rørholderen ind i det

firkantede hul.

1

2

3

4

1 Enhed

2 Tape

3 Rørholder

4 Hul

b) Hægt nederste ende i underkanten af

enheden.

20 electrolux

Sidan laddas ...

Electrolux EXH09HX1WI Användarmanual

Denna manual är också lämplig för

Electrolux EXH09HX1WI Användarmanual

på andra språk

Relaterade papper

Andra dokument