Philips SCF355/00 Användarmanual

Specications are subject to change without notice

4213 342 20536

SCF355

1 2 3 4 5

6

7 8 9

10 11 12 13

14 15 16

SCF355

ENGLISH 6

DANSK 17

ΕΛΛΗΝΙΚΑ 28

ESPAÑOL 40

SUOMI 53

NORSK 64

PORTUGUÊS 75

SVENSKA 88

6

General description (Fig. 1)

1. Bottle warmer

2. Light

3. Settings knob

4. O setting

5. Defrost setting

6. Keep warm setting

7. Express milk warming setting for contents up to

180ml/6oz

8. Food warming setting

9. Express milk warming setting for contents over and

including 180ml/6oz

Important

To fully benet from the support that Philips

oers, register your appliance at

www.philips.com/welcome.

Read this user manual carefully before you

use the bottle warmer and save it for future

reference.

Danger

- Do not immerse the cord, plug or

appliance in water or other liquid.

Warning

- Only use the appliance indoors.

- Do not let the mains cord hang over the

edge of a table or worktop. Excess cord

can be stored in the base of the bottle

warmer.

- Keep the mains cord away from hot

surfaces.

ENGLISH

- Only connect the appliance to an earthed

wall socket. Always make sure that the

plug is inserted into the wall socket

properly.

- Check if the voltage indicated on the

bottom of the appliance corresponds to

the local mains voltage before you

connect the appliance.

- If you need to use an extension cord,

make sure it is an earthed extension cord

with a rating of at least 13 amperes.

- Do not use the appliance if the plug, the

mains cord or the appliance itself is

damaged. If the mains cord is damaged,

you must have it replaced by Philips,

a service centre authorised by Philips or

similarly qualied persons in order to avoid

a hazard.

- Do not place the appliance on or near a

hot gas or electric cooker, or in a heated

oven.

- This appliances can be used by persons

with reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given

supervision or instruction concerning use

of the appliance in a safe way and

understand the hazards involved.

ENGLISH 7

- Cleaning and user maintenance shall not

be made by children.

- This appliance shall not be used by

children. Keep the appliance and its cord

out of reach of children.

- Children shall not play with the appliance.

- Do not spill water on the mains plug.

- Only use the appliance as described in

the user manual to avoid potential injury

due to misuse.

- Do not preheat the appliance.

- Always place a fully assembled bottle

with cap in the bottle warmer before you

add water.

- Make sure you add water before you

switch on the bottle warmer.

- Hot water can cause serious burns. Be

careful when the bottle warmer contains

hot water.

- The accessible surfaces of the appliance

may become hot during use and are

subject to residual heat after use.

- Do not move the appliance when it

contains hot water.

- When the food or milk has reached the

required temperature, remove the bottle or

container from the bottle warmer. If you

leave food or milk in the bottle warmer, the

temperature of the food or milk increases.

ENGLISH8

- Always check the food temperature

before you feed your child.

Caution

- This appliance is intended to be used in

household and similar applications such

as farm houses, bed and breakfast type

environments, sta kitchen areas in

shops, oces and other working

environments, and by clients in hotels,

motels and other residential type

environments.

- Unplug the appliance when it is not in

use.

- The surface of the heating element is

subject to residual heat after use.

- Let the appliance cool down before you

clean it.

- Follow the descaling instructions to avoid

irreparable damage.

- Do not try to open or repair the appliance

yourself. You can contact the Philips

Consumer Care Centre in your country

(see www.philips.com/support).

- The food should not be heated for too

long.

You can nd the production date code YYWW in the cord

storage compartment in the base of the bottle warmer.

ENGLISH 9

Electromagnetic elds (EMF)

This Philips appliance complies with all applicable standards

and regulations regarding exposure to electromagnetic elds.

Using the bottle warmer

With this bottle warmer, you can safely warm all Philips Avent

feeding bottles and milk/baby food in containers and other

baby food jars.

Note: Philips Avent breast milk bags and Philips Avent

2oz/60ml bottles cannot be used in this bottle warmer.

Explanation of settings

- O setting: The bottle warmer is switched o and the light

is o. On every other setting, the appliance is switched on

and the light is lit (Fig. 2).

-

Express milk warming setting for contents up to 180ml/6oz:

Select this setting when you want to quickly warm a bottle of

milk with a content up to 180ml/6oz.

The bottle has to be taken out immediately after warming to

the right temperature, otherwise the milk will be overheated.

- Food warming setting: Select this setting when you want

to warm a container/jar of baby food.

- Express milk warming setting for contents over and

including 180ml/6oz:

Select this setting when you want to quickly warm a bottle

of milk with a content over and including 180ml/6oz.

The bottle needs to be taken out immediately after

warming to the right temperature, otherwise the milk will be

overheated.

- Keep warm setting: Milk is warmed at a slower speed and

be kept at right temperature.

- Defrost setting: Defrost a bottle/container of milk/baby

food to liquid state. No warming occurs.

ENGLISH10

Using the bottle warmer with express milk warming setting

1 Put the mains plug in the wall socket (Fig. 3).

2 Place a bottle in the bottle warmer (Fig. 4).

3 Fill the bottle warmer with drinking water up to the level

of the milk in the bottle. In case of large amounts of milk,

the maximum level of water is approximately 1 cm below

the top of the bottle warmer. An accurate water level

ensures correct warming performance (Fig. 5).

4 Select the desired setting based on the milk volume. See

the express warming reference table at the end of this

chapter to check how long the milk needs to be warmed

in the selected setting (Fig. 6).

Note: The speed of warming milk depends on the amount of

the milk warmed and on its initial temperature, i.e. room

temperature (20°C) or fridge temperature (5°C).

5 The orange light goes on when you select a setting. This

indicates that the bottle warmer is on (Fig. 7).

Note: Whilst warming the milk circulates and heats evenly.

6 Check the express warming reference table for the time

required to warm the milk. Remove the bottle from the

bottle warmer after the time indicated in the express

warming reference table has passed (Fig. 8).

Tip: When you nd the milk is not warm enough, you can

place the bottle back into the appliance for a maximum of

30 seconds of extra warming. This will create a slightly

warmer result but without overheating.

Caution: If you leave the bottle in the bottle warmer longer

than the time indicated in the settings table, the milk may

become overheated.

Note: If you overheat breast milk, valuable nutrients and

vitamins may be lost.

ENGLISH 11

7 Always check the temperature before you feed your

baby. Gently shake the bottle or milk storage container and

check the temperature of the milk by sprinkling a few drops

on the inside of your wrist (Fig. 9).

8 Turn the knob back to the ‘o’ position (Fig. 10).

Caution: The water in the bottle warmer might be hot after

nishing warming milk / baby food. Be careful that hot water

can cause serious burns.

If you do not turn the knob back to the ‘o’ position, the

water keeps heating up and will reach a very high

temperature.

Express warming reference table

ml/oz min min

5°C/40°F 20°C/70°F

60 ml/2 oz-90 ml/3 oz 4.5 3.0

90 ml/3 oz-110 ml/3.7 oz 5.5 3.0

125 ml/4 oz-150 ml/5 oz 3.5 3.0

180 ml/6 oz-210 ml/7 oz 5.5 4.0

240 ml/8 oz-260 ml/9 oz 7.0 4.5

290 ml/10 oz-330 ml/11 oz 7.5 5.0

Note: The indicated warming times are based on Philips

Avent Classic and Natural PP bottle ranges. Be aware that

warming timings of Philips Avent standard bottles and glass

bottles deviate from these indications. The characteristics of

bottles such as material or thickness may also impact the

warming times, therefore it may take less time to warm a

larger volume of milk.

ENGLISH12

Note: The milk may feel cool to you, but for a newborn baby

its temperature is very pleasant.

Using the bottle warmer to warm baby food

1 Follow the same steps as indicated in the previous

paragraph.

2 Make sure to stir the baby food during warming as it

does not circulate automatically. Be careful not to burn

your ngers when holding the container/jar while stirring

(Fig. 11).

After warming test the baby food with a spoon to ensure it is

not too hot. If the baby food is not warm enough, put the

container back into the bottle warmer and warm the baby food

until it has the desired temperature.

Note: Due to the high variety of baby food consistencies, it

is strongly recommended to continuously stir and check

while you are warming the baby food for an optimal result.

Note: Due to the high variety of baby food consistencies, it

is not possible to indicate warming timings for baby food.

Using the keep warm setting to warm milk

1 Put the mains plug in the wall socket (Fig. 3).

2 Place the bottle or container in the bottle warmer (Fig. 4).

3 Fill the bottle warmer with drinking water up to the

level of the milk in the bottle/container. In case of

large amounts of milk, the maximum level of water is

approximately 1 cm below the top of the bottle warmer

(Fig. 5).

4 Select the position of keep warm (Fig. 6).

At this setting, you can warm your milk at a slow pace and

keep it warm at the right end temperature. E.g. to warm a

bottle of 4oz milk starting from room temperature, it will

take 15-20min. The warming time may be longer or shorter

depends on the milk volumes and starting temperature.

ENGLISH 13

Note: Philips Avent recommends to feed your baby as

soon as possible after the milk is warmed. We advise not to

reheat the milk after it has cooled down again.

Note: Always check the temperature before you feed your

baby (Fig. 9).

5 Turn the knob back to the ‘o’ position when the bottle/

container is removed from the bottle warmer (Fig. 10).

Using the bottle warmer with defrost setting

1 Put the mains plug in the wall socket (Fig. 3).

2 Place the bottle or container in the bottle warmer (Fig. 4).

3 Fill the bottle warmer with drinking water up to the level

of the milk/baby food in the bottle/container. In case of

large amounts of milk/baby food, the maximum level of

water is approximately 1 cm below the top of the bottle

warmer (Fig. 5).

4 Select the position of defrost (Fig. 6).

At this setting, your frozen milk/baby food can be defrosted

till liquid state.

For frozen milk, check the warming reference table for the

expected defrost timings, as indication one small and one

larger milk volume are included in the table. After your milk is

defrosted, choose express warming setting or keep warming

setting to warm your milk. Please refer to the previous

chapters for usage instructions. Consider the start

temperature of your milk around fridge temperature for the

warming timings as rough guideline.

ml/oz hours

60 ml/2 oz-90 ml/3 oz 1-1.5

180 ml/6 oz-210 ml/7 oz 1.5-2.5

ENGLISH14

5 You may also defrost baby food in Philips Avent food

container by this setting. After your baby food is

defrosted, choose food warming setting to warm it.

Please refer to the previous chapter for usage instruction.

Note: Due to the high variety of baby food consistencies, it

is strongly recommended to continuously stir and check

while you are defrosting the baby food for an optimal result.

Note: Due to the high variety of baby food consistencies, it

is not possible to indicate warming timings for baby food.

Cleaning and descaling

Cleaning

1 After each use, unplug the bottle warmer and let it cool

down (Fig. 12).

2 Remove the water from the bottle warmer for hygienic

reasons (Fig. 13).

3 Wipe the outside and inside of the bottle warmer with a

moist cloth (Fig. 14).

Do not use abrasive, anti-bacterial cleaning agents,

chemical solvents or sharp tools to clean the bottle warmer.

Note: If you used the bottle warmer to warm containers with

baby food, make sure that no spilled baby food remains on

the bottom of the bottle warmer.

ENGLISH 15

Descaling

It is recommended to descale the bottle warmer every four

weeks to ensure it continues to work eciently.

1 Mix 50ml/1.7oz of white vinegar with 100ml/3.4oz of cold

water to descale the bottle warmer. Switch on the bottle

warmer, select the milk warming setting for contents

under 180ml/6oz and let the appliance operate for 10

minutes. Leave the solution in the bottle warmer until all

scale has dissolved (Fig. 15).

Note: You can also use citric acid based descalers.

Note: Do not use other types of descalers.

2 Unplug the bottle warmer before you empty it (Fig. 12).

3 Empty the bottle warmer and rinse its inside thoroughly.

If you still see traces of scale after rinsing, repeat the

descaling procedure (Fig. 13).

Recycling

- This symbol means that this product shall not be disposed

of with normal household waste (2012/19/EU). (Fig. 16)

- Follow your country’s rules for the separate collection of

electrical and electronic products. Correct disposal helps

prevent negative consequences for the environment and

human health.

Guarantee and support

If you need information or support, please visit

www.philips.com/support or read the separate worldwide

guarantee leaet.

ENGLISH16

DANSK 17

Generel beskrivelse (g. 1)

1. Flaskevarmer

2. Lys

3. Indstillingsknap

4. O-indstilling

5. Optøningsindstilling

6. Hold varm-indstilling

7. Indstilling for ekspresopvarmning af mælk for indhold op

til 180 ml/6 oz

8. Indstilling for opvarmning af mad

9. Indstilling for ekspresopvarmning af mælk for indhold på

180 ml/6 oz og derover

Vigtigt

For at få fuldt udbytte af den vejledning,

som Philips tilbyder, skal du registrere dit

apparat på www.philips.com/welcome.

Læs denne brugervejledning omhyggeligt

igennem, inden askevarmeren tages i brug,

og opbevar den til eventuel senere brug.

Fare

- Ledning, stik eller apparat må aldrig

kommes ned i vand eller andre væsker.

Advarsel

- Apparatet må kun anvendes indendørs.

- Lad aldrig ledningen hænge ud over

kanten af et bord eller køkkenbord.

Overskydende ledning kan opbevares i

bunden af askevarmeren.

- Sørg for, at netledningen ikke kommer i

berøring med varme ader.

- Apparatet må kun sluttes til en stikkontakt

med jordforbindelse. Kontrollér altid, at

stikket er sat korrekt i stikkontakten.

- Kontrollér, om spændingsangivelsen i

bunden af apparatet svarer til den lokale

netspænding, før du slutter strøm til

apparatet.

- Hvis du skal bruge en forlængerledning,

skal du sørge for, at det er en

forlængerledning med jordforbindelse og

på mindst 13 ampere.

- Brug ikke apparatet, hvis stik, netledning,

eller selve apparatet er beskadiget. Hvis

netledningen beskadiges, må den kun

udskiftes af Philips,

et autoriseret Philips-serviceværksted

eller en tilsvarende kvaliceret fagmand

for at undgå enhver risiko.

- Placér ikke apparatet på eller i nærheden

af et varmt gasblus eller en elkoger eller i

en varm ovn.

- Dette apparat kan bruges af personer

med reducerede fysiske, sensoriske eller

mentale evner eller manglende erfaring

og viden, hvis de er blevet instrueret i

sikker brug af apparatet og forstår de

medfølgende risici.

DANSK18

- Rengøring og vedligeholdelse må ikke

foretages af børn.

- Dette apparat må ikke bruges af børn.

Hold apparatet og ledningen til apparatet

uden for børns rækkevidde.

- Lad ikke børn lege med apparatet.

- Undgå at spilde vand på stikket.

- Brug kun apparatet som beskrevet i

brugervejledningen for derved at undgå

mulig personskade på grund af

forkert brug.

- Undlad at forvarme apparatet.

- Placer altid en fuldt samlet aske med låg

i askevarmeren, før du tilføjer vand.

- Sørg for at tilføje vand, før du tænder for

askevarmeren.

- Varmt vand kan forårsage alvorlige

brandsår.

Pas på, når der er varmt vand i

askevarmeren.

- Ydersiden kan blive varm under brug og

udsættes for spildvarme efter brug.

-

Flyt ikke apparatet, hvis det indeholder

varmt vand.

DANSK 19

- Når maden eller mælken har nået det

ønskede temperatur, skal du fjerne

asken eller beholderen fra

askevarmeren. Hvis du efterlader mad

eller mælk i askevarmeren, forøges

madens eller mælkens temperatur.

- Kontroller altid madens temperatur, før du

begynder at made dit barn.

Forsigtig

- Dette apparat er beregnet til brug i

hjemmet og andre lignende steder;

såsom gårde, bed and breakfast-steder,

personalekøkkener i butikker, på kontorer

og i andre arbejdspladser. Det kan også

benyttes af gæster på hoteller og

moteller.

- Tag stikket ud af apparatet, når det ikke er

i brug.

-

Varmelegemets overade kan være varm

efter brug.

- Lad apparatet køle af, før du stiller den væk.

- Følg afkalkningsinstruktionerne for at

undgå uoprettelig skade.

- Prøv ikke selv at åbne eller reparere

apparatet. Du kan kontakte det lokale

Philips Kundecenter

(se www.philips.com/support).

- Maden bør ikke opvarmes for længe.

DANSK20

Elektromagnetiske felter (EMF)

Dette Philips-apparat overholder alle branchens gældende

standarder og regler angående eksponering for

elektromagnetiske felter.

Brug af askevarmeren

Med denne askevarmer kan du på sikker vis varme alle

Philips Avent-sutteasker og mælk/babymad i beholdere og

andre glas med babymad.

Bemærk: Philips Avent-modermælksposer og Philips

Avent-sutteasker på 60 ml/2 oz kan ikke bruges i denne

askevarmer.

Forklaring af indstillinger

- O-indstilling: Flaskevarmeren er slukket, og lyset er

slukket. På alle andre indstillinger er apparatet tændt, og

lyset er tændt (Fig. 2).

-

Indstilling for ekspresopvarmning af mælk for indhold op til

180 ml/6 oz: Vælg denne indstilling, hvis du hurtigt vil

varme en aske mælk med et indhold på op til 180 ml/6

oz.

Flasken skal tages ud umiddelbart efter opvarmning til den

korrekte temperatur. Ellers overophedes mælken.

- Indstilling for opvarmning af mad: Vælg denne indstilling,

hvis du vil varme en beholder/et glas med babymad.

- Indstilling for ekspresopvarmning af mælk for indhold på

180 ml/6 oz og derover:

Vælg denne indstilling, hvis du hurtigt vil opvarme en

aske mælk med et indhold på 180 ml/6 oz eller derover.

Flasken skal tages ud umiddelbart efter opvarmning til

den korrekte temperatur. Ellers overophedes mælken.

- Hold varm-indstilling: Mælken opvarmes langsommere og

holder den korrekte temperatur.

- Optøningsindstilling: Optø en aske/beholder med mælk/

babymad til ydende tilstand. Der opvarmes ikke.

DANSK 21

Brug af askevarmeren med indstilling for

ekspresopvarmning af mælk

1 Sæt stikket i stikkontakten (Fig. 3).

2 Placer en aske i askevarmeren (Fig. 4).

3 Fyld drikkevand i asken op til niveauet for mælk i

asken. Ved store mængder mælk er den maksimale

vandstand omtrent 1 cm under toppen af askevarmeren.

En præcis vandstand sikrer en korrekt

opvarmningsydeevne (Fig. 5).

4 Vælg den ønskede indstilling ud fra mængden af mælk.

Se referencetabellen for ekspresopvarmning sidst i dette

kapitel for at nde ud af, hvor længe mælken skal

opvarmes i den valgte indstilling (Fig. 6).

Bemærk: Hastigheden for opvarmning af mælk afhænger af

mængden af mælk, der skal varmes, og af den oprindelige

temperatur, f.eks. stuetemperatur (20 °C) eller

køleskabstemperatur (5 °C).

5 Det orange lys tændes, når du vælger en indstilling.

Dette indikerer, at askevarmeren er tændt (Fig. 7).

Bemærk: Under opvarmningen cirkuleres mælken, så den

opvarmes jævnt.

6 Se i referencetabellen for ekspresopvarmning, hvor lang

tid det tager at opvarme mælken. Fjern asken fra

askevarmeren, når den tid, som er angivet i

referencetabellen for ekspresopvarmning, er gået (Fig. 8).

Tip: Hvis du ikke synes, at mælken er varm nok, kan du stille

asken tilbage i apparatet til ekstra opvarmning i højst 30

sekunder. Dette vil give et lidt varmere resultat, men uden

overophedning.

Forsigtig: Hvis du efterlader asken i askevarmeren i

længere tid end den angivne tid i indstillingstabellen,

risikerer du, at mælken bliver overophedet.

DANSK22

Sidan laddas ...

Philips SCF355/00 Användarmanual

Philips SCF355/00 Användarmanual

på andra språk

Relaterade papper

Andra dokument