Avent AVENT SCF355/00 Användarmanual

Kategori
Flaskvärmare
Typ
Användarmanual
Specications are subject to change without notice
© 2018 Koninklijke Philips N.V.
All rights reserved
4213 342 20536
SCF355
1 2 3 4 5
6
7 8 9
10 11 12 13
14 15 16
SCF355
ENGLISH 6
DANSK 17
ΕΛΛΗΝΙΚΑ 28
ESPAÑOL 40
SUOMI 53
NORSK 64
PORTUGUÊS 75
SVENSKA 88
6
General description (Fig. 1)
1. Bottle warmer
2. Light
3. Settings knob
4. O setting
5. Defrost setting
6. Keep warm setting
7. Express milk warming setting for contents up to
180ml/6oz
8. Food warming setting
9. Express milk warming setting for contents over and
including 180ml/6oz
Important
To fully benet from the support that Philips
oers, register your appliance at
www.philips.com/welcome.
Read this user manual carefully before you
use the bottle warmer and save it for future
reference.
Danger
- Do not immerse the cord, plug or
appliance in water or other liquid.
Warning
- Only use the appliance indoors.
- Do not let the mains cord hang over the
edge of a table or worktop. Excess cord
can be stored in the base of the bottle
warmer.
- Keep the mains cord away from hot
surfaces.
ENGLISH
- Only connect the appliance to an earthed
wall socket. Always make sure that the
plug is inserted into the wall socket
properly.
- Check if the voltage indicated on the
bottom of the appliance corresponds to
the local mains voltage before you
connect the appliance.
- If you need to use an extension cord,
make sure it is an earthed extension cord
with a rating of at least 13 amperes.
- Do not use the appliance if the plug, the
mains cord or the appliance itself is
damaged. If the mains cord is damaged,
you must have it replaced by Philips,
a service centre authorised by Philips or
similarly qualied persons in order to avoid
a hazard.
- Do not place the appliance on or near a
hot gas or electric cooker, or in a heated
oven.
- This appliances can be used by persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use
of the appliance in a safe way and
understand the hazards involved.
ENGLISH 7
- Cleaning and user maintenance shall not
be made by children.
- This appliance shall not be used by
children. Keep the appliance and its cord
out of reach of children.
- Children shall not play with the appliance.
- Do not spill water on the mains plug.
- Only use the appliance as described in
the user manual to avoid potential injury
due to misuse.
- Do not preheat the appliance.
- Always place a fully assembled bottle
with cap in the bottle warmer before you
add water.
- Make sure you add water before you
switch on the bottle warmer.
- Hot water can cause serious burns. Be
careful when the bottle warmer contains
hot water.
- The accessible surfaces of the appliance
may become hot during use and are
subject to residual heat after use.
- Do not move the appliance when it
contains hot water.
- When the food or milk has reached the
required temperature, remove the bottle or
container from the bottle warmer. If you
leave food or milk in the bottle warmer, the
temperature of the food or milk increases.
ENGLISH8
- Always check the food temperature
before you feed your child.
Caution
- This appliance is intended to be used in
household and similar applications such
as farm houses, bed and breakfast type
environments, sta kitchen areas in
shops, oces and other working
environments, and by clients in hotels,
motels and other residential type
environments.
- Unplug the appliance when it is not in
use.
- The surface of the heating element is
subject to residual heat after use.
- Let the appliance cool down before you
clean it.
- Follow the descaling instructions to avoid
irreparable damage.
- Do not try to open or repair the appliance
yourself. You can contact the Philips
Consumer Care Centre in your country
(see www.philips.com/support).
- The food should not be heated for too
long.
You can nd the production date code YYWW in the cord
storage compartment in the base of the bottle warmer.
ENGLISH 9
Electromagnetic elds (EMF)
This Philips appliance complies with all applicable standards
and regulations regarding exposure to electromagnetic elds.
Using the bottle warmer
With this bottle warmer, you can safely warm all Philips Avent
feeding bottles and milk/baby food in containers and other
baby food jars.
Note: Philips Avent breast milk bags and Philips Avent
2oz/60ml bottles cannot be used in this bottle warmer.
Explanation of settings
- O setting: The bottle warmer is switched o and the light
is o. On every other setting, the appliance is switched on
and the light is lit (Fig. 2).
-
Express milk warming setting for contents up to 180ml/6oz:
Select this setting when you want to quickly warm a bottle of
milk with a content up to 180ml/6oz.
The bottle has to be taken out immediately after warming to
the right temperature, otherwise the milk will be overheated.
- Food warming setting: Select this setting when you want
to warm a container/jar of baby food.
- Express milk warming setting for contents over and
including 180ml/6oz:
Select this setting when you want to quickly warm a bottle
of milk with a content over and including 180ml/6oz.
The bottle needs to be taken out immediately after
warming to the right temperature, otherwise the milk will be
overheated.
- Keep warm setting: Milk is warmed at a slower speed and
be kept at right temperature.
- Defrost setting: Defrost a bottle/container of milk/baby
food to liquid state. No warming occurs.
ENGLISH10
Using the bottle warmer with express milk warming setting
1 Put the mains plug in the wall socket (Fig. 3).
2 Place a bottle in the bottle warmer (Fig. 4).
3 Fill the bottle warmer with drinking water up to the level
of the milk in the bottle. In case of large amounts of milk,
the maximum level of water is approximately 1 cm below
the top of the bottle warmer. An accurate water level
ensures correct warming performance (Fig. 5).
4 Select the desired setting based on the milk volume. See
the express warming reference table at the end of this
chapter to check how long the milk needs to be warmed
in the selected setting (Fig. 6).
Note: The speed of warming milk depends on the amount of
the milk warmed and on its initial temperature, i.e. room
temperature (20°C) or fridge temperature (5°C).
5 The orange light goes on when you select a setting. This
indicates that the bottle warmer is on (Fig. 7).
Note: Whilst warming the milk circulates and heats evenly.
6 Check the express warming reference table for the time
required to warm the milk. Remove the bottle from the
bottle warmer after the time indicated in the express
warming reference table has passed (Fig. 8).
Tip: When you nd the milk is not warm enough, you can
place the bottle back into the appliance for a maximum of
30 seconds of extra warming. This will create a slightly
warmer result but without overheating.
Caution: If you leave the bottle in the bottle warmer longer
than the time indicated in the settings table, the milk may
become overheated.
Note: If you overheat breast milk, valuable nutrients and
vitamins may be lost.
ENGLISH 11
7 Always check the temperature before you feed your
baby. Gently shake the bottle or milk storage container and
check the temperature of the milk by sprinkling a few drops
on the inside of your wrist (Fig. 9).
8 Turn the knob back to the ‘o’ position (Fig. 10).
Caution: The water in the bottle warmer might be hot after
nishing warming milk / baby food. Be careful that hot water
can cause serious burns.
If you do not turn the knob back to the ‘o’ position, the
water keeps heating up and will reach a very high
temperature.
Express warming reference table
ml/oz min min
5°C/40°F 20°C/70°F
60 ml/2 oz-90 ml/3 oz 4.5 3.0
90 ml/3 oz-110 ml/3.7 oz 5.5 3.0
125 ml/4 oz-150 ml/5 oz 3.5 3.0
180 ml/6 oz-210 ml/7 oz 5.5 4.0
240 ml/8 oz-260 ml/9 oz 7.0 4.5
290 ml/10 oz-330 ml/11 oz 7.5 5.0
Note: The indicated warming times are based on Philips
Avent Classic and Natural PP bottle ranges. Be aware that
warming timings of Philips Avent standard bottles and glass
bottles deviate from these indications. The characteristics of
bottles such as material or thickness may also impact the
warming times, therefore it may take less time to warm a
larger volume of milk.
ENGLISH12
Note: The milk may feel cool to you, but for a newborn baby
its temperature is very pleasant.
Using the bottle warmer to warm baby food
1 Follow the same steps as indicated in the previous
paragraph.
2 Make sure to stir the baby food during warming as it
does not circulate automatically. Be careful not to burn
your ngers when holding the container/jar while stirring
(Fig. 11).
After warming test the baby food with a spoon to ensure it is
not too hot. If the baby food is not warm enough, put the
container back into the bottle warmer and warm the baby food
until it has the desired temperature.
Note: Due to the high variety of baby food consistencies, it
is strongly recommended to continuously stir and check
while you are warming the baby food for an optimal result.
Note: Due to the high variety of baby food consistencies, it
is not possible to indicate warming timings for baby food.
Using the keep warm setting to warm milk
1 Put the mains plug in the wall socket (Fig. 3).
2 Place the bottle or container in the bottle warmer (Fig. 4).
3 Fill the bottle warmer with drinking water up to the
level of the milk in the bottle/container. In case of
large amounts of milk, the maximum level of water is
approximately 1 cm below the top of the bottle warmer
(Fig. 5).
4 Select the position of keep warm (Fig. 6).
At this setting, you can warm your milk at a slow pace and
keep it warm at the right end temperature. E.g. to warm a
bottle of 4oz milk starting from room temperature, it will
take 15-20min. The warming time may be longer or shorter
depends on the milk volumes and starting temperature.
ENGLISH 13
Note: Philips Avent recommends to feed your baby as
soon as possible after the milk is warmed. We advise not to
reheat the milk after it has cooled down again.
Note: Always check the temperature before you feed your
baby (Fig. 9).
5 Turn the knob back to the ‘o’ position when the bottle/
container is removed from the bottle warmer (Fig. 10).
Using the bottle warmer with defrost setting
1 Put the mains plug in the wall socket (Fig. 3).
2 Place the bottle or container in the bottle warmer (Fig. 4).
3 Fill the bottle warmer with drinking water up to the level
of the milk/baby food in the bottle/container. In case of
large amounts of milk/baby food, the maximum level of
water is approximately 1 cm below the top of the bottle
warmer (Fig. 5).
4 Select the position of defrost (Fig. 6).
At this setting, your frozen milk/baby food can be defrosted
till liquid state.
For frozen milk, check the warming reference table for the
expected defrost timings, as indication one small and one
larger milk volume are included in the table. After your milk is
defrosted, choose express warming setting or keep warming
setting to warm your milk. Please refer to the previous
chapters for usage instructions. Consider the start
temperature of your milk around fridge temperature for the
warming timings as rough guideline.
ml/oz hours
60 ml/2 oz-90 ml/3 oz 1-1.5
180 ml/6 oz-210 ml/7 oz 1.5-2.5
ENGLISH14
5 You may also defrost baby food in Philips Avent food
container by this setting. After your baby food is
defrosted, choose food warming setting to warm it.
Please refer to the previous chapter for usage instruction.
Note: Due to the high variety of baby food consistencies, it
is strongly recommended to continuously stir and check
while you are defrosting the baby food for an optimal result.
Note: Due to the high variety of baby food consistencies, it
is not possible to indicate warming timings for baby food.
Cleaning and descaling
Cleaning
1 After each use, unplug the bottle warmer and let it cool
down (Fig. 12).
2 Remove the water from the bottle warmer for hygienic
reasons (Fig. 13).
3 Wipe the outside and inside of the bottle warmer with a
moist cloth (Fig. 14).
Do not use abrasive, anti-bacterial cleaning agents,
chemical solvents or sharp tools to clean the bottle warmer.
Note: If you used the bottle warmer to warm containers with
baby food, make sure that no spilled baby food remains on
the bottom of the bottle warmer.
ENGLISH 15
Descaling
It is recommended to descale the bottle warmer every four
weeks to ensure it continues to work eciently.
1 Mix 50ml/1.7oz of white vinegar with 100ml/3.4oz of cold
water to descale the bottle warmer. Switch on the bottle
warmer, select the milk warming setting for contents
under 180ml/6oz and let the appliance operate for 10
minutes. Leave the solution in the bottle warmer until all
scale has dissolved (Fig. 15).
Note: You can also use citric acid based descalers.
Note: Do not use other types of descalers.
2 Unplug the bottle warmer before you empty it (Fig. 12).
3 Empty the bottle warmer and rinse its inside thoroughly.
If you still see traces of scale after rinsing, repeat the
descaling procedure (Fig. 13).
Recycling
- This symbol means that this product shall not be disposed
of with normal household waste (2012/19/EU). (Fig. 16)
- Follow your country’s rules for the separate collection of
electrical and electronic products. Correct disposal helps
prevent negative consequences for the environment and
human health.
Guarantee and support
If you need information or support, please visit
www.philips.com/support or read the separate worldwide
guarantee leaet.
ENGLISH16
DANSK 17
Generel beskrivelse (g. 1)
1. Flaskevarmer
2. Lys
3. Indstillingsknap
4. O-indstilling
5. Optøningsindstilling
6. Hold varm-indstilling
7. Indstilling for ekspresopvarmning af mælk for indhold op
til 180 ml/6 oz
8. Indstilling for opvarmning af mad
9. Indstilling for ekspresopvarmning af mælk for indhold på
180 ml/6 oz og derover
Vigtigt
For at få fuldt udbytte af den vejledning,
som Philips tilbyder, skal du registrere dit
apparat på www.philips.com/welcome.
Læs denne brugervejledning omhyggeligt
igennem, inden askevarmeren tages i brug,
og opbevar den til eventuel senere brug.
Fare
- Ledning, stik eller apparat må aldrig
kommes ned i vand eller andre væsker.
Advarsel
- Apparatet må kun anvendes indendørs.
- Lad aldrig ledningen hænge ud over
kanten af et bord eller køkkenbord.
Overskydende ledning kan opbevares i
bunden af askevarmeren.
- Sørg for, at netledningen ikke kommer i
berøring med varme ader.
- Apparatet må kun sluttes til en stikkontakt
med jordforbindelse. Kontrollér altid, at
stikket er sat korrekt i stikkontakten.
- Kontrollér, om spændingsangivelsen i
bunden af apparatet svarer til den lokale
netspænding, før du slutter strøm til
apparatet.
- Hvis du skal bruge en forlængerledning,
skal du sørge for, at det er en
forlængerledning med jordforbindelse og
på mindst 13 ampere.
- Brug ikke apparatet, hvis stik, netledning,
eller selve apparatet er beskadiget. Hvis
netledningen beskadiges, må den kun
udskiftes af Philips,
et autoriseret Philips-serviceværksted
eller en tilsvarende kvaliceret fagmand
for at undgå enhver risiko.
- Placér ikke apparatet på eller i nærheden
af et varmt gasblus eller en elkoger eller i
en varm ovn.
- Dette apparat kan bruges af personer
med reducerede fysiske, sensoriske eller
mentale evner eller manglende erfaring
og viden, hvis de er blevet instrueret i
sikker brug af apparatet og forstår de
medfølgende risici.
DANSK18
- Rengøring og vedligeholdelse må ikke
foretages af børn.
- Dette apparat må ikke bruges af børn.
Hold apparatet og ledningen til apparatet
uden for børns rækkevidde.
- Lad ikke børn lege med apparatet.
- Undgå at spilde vand på stikket.
- Brug kun apparatet som beskrevet i
brugervejledningen for derved at undgå
mulig personskade på grund af
forkert brug.
- Undlad at forvarme apparatet.
- Placer altid en fuldt samlet aske med låg
i askevarmeren, før du tilføjer vand.
- Sørg for at tilføje vand, før du tænder for
askevarmeren.
- Varmt vand kan forårsage alvorlige
brandsår.
Pas på, når der er varmt vand i
askevarmeren.
- Ydersiden kan blive varm under brug og
udsættes for spildvarme efter brug.
-
Flyt ikke apparatet, hvis det indeholder
varmt vand.
DANSK 19
- Når maden eller mælken har nået det
ønskede temperatur, skal du fjerne
asken eller beholderen fra
askevarmeren. Hvis du efterlader mad
eller mælk i askevarmeren, forøges
madens eller mælkens temperatur.
- Kontroller altid madens temperatur, før du
begynder at made dit barn.
Forsigtig
- Dette apparat er beregnet til brug i
hjemmet og andre lignende steder;
såsom gårde, bed and breakfast-steder,
personalekøkkener i butikker, på kontorer
og i andre arbejdspladser. Det kan også
benyttes af gæster på hoteller og
moteller.
- Tag stikket ud af apparatet, når det ikke er
i brug.
-
Varmelegemets overade kan være varm
efter brug.
- Lad apparatet køle af, før du stiller den væk.
- Følg afkalkningsinstruktionerne for at
undgå uoprettelig skade.
- Prøv ikke selv at åbne eller reparere
apparatet. Du kan kontakte det lokale
Philips Kundecenter
(se www.philips.com/support).
- Maden bør ikke opvarmes for længe.
DANSK20
Elektromagnetiske felter (EMF)
Dette Philips-apparat overholder alle branchens gældende
standarder og regler angående eksponering for
elektromagnetiske felter.
Brug af askevarmeren
Med denne askevarmer kan du på sikker vis varme alle
Philips Avent-sutteasker og mælk/babymad i beholdere og
andre glas med babymad.
Bemærk: Philips Avent-modermælksposer og Philips
Avent-sutteasker på 60 ml/2 oz kan ikke bruges i denne
askevarmer.
Forklaring af indstillinger
- O-indstilling: Flaskevarmeren er slukket, og lyset er
slukket. På alle andre indstillinger er apparatet tændt, og
lyset er tændt (Fig. 2).
-
Indstilling for ekspresopvarmning af mælk for indhold op til
180 ml/6 oz: Vælg denne indstilling, hvis du hurtigt vil
varme en aske mælk med et indhold på op til 180 ml/6
oz.
Flasken skal tages ud umiddelbart efter opvarmning til den
korrekte temperatur. Ellers overophedes mælken.
- Indstilling for opvarmning af mad: Vælg denne indstilling,
hvis du vil varme en beholder/et glas med babymad.
- Indstilling for ekspresopvarmning af mælk for indhold på
180 ml/6 oz og derover:
Vælg denne indstilling, hvis du hurtigt vil opvarme en
aske mælk med et indhold på 180 ml/6 oz eller derover.
Flasken skal tages ud umiddelbart efter opvarmning til
den korrekte temperatur. Ellers overophedes mælken.
- Hold varm-indstilling: Mælken opvarmes langsommere og
holder den korrekte temperatur.
- Optøningsindstilling: Optø en aske/beholder med mælk/
babymad til ydende tilstand. Der opvarmes ikke.
DANSK 21
Brug af askevarmeren med indstilling for
ekspresopvarmning af mælk
1 Sæt stikket i stikkontakten (Fig. 3).
2 Placer en aske i askevarmeren (Fig. 4).
3 Fyld drikkevand i asken op til niveauet for mælk i
asken. Ved store mængder mælk er den maksimale
vandstand omtrent 1 cm under toppen af askevarmeren.
En præcis vandstand sikrer en korrekt
opvarmningsydeevne (Fig. 5).
4 Vælg den ønskede indstilling ud fra mængden af mælk.
Se referencetabellen for ekspresopvarmning sidst i dette
kapitel for at nde ud af, hvor længe mælken skal
opvarmes i den valgte indstilling (Fig. 6).
Bemærk: Hastigheden for opvarmning af mælk afhænger af
mængden af mælk, der skal varmes, og af den oprindelige
temperatur, f.eks. stuetemperatur (20 °C) eller
køleskabstemperatur (5 °C).
5 Det orange lys tændes, når du vælger en indstilling.
Dette indikerer, at askevarmeren er tændt (Fig. 7).
Bemærk: Under opvarmningen cirkuleres mælken, så den
opvarmes jævnt.
6 Se i referencetabellen for ekspresopvarmning, hvor lang
tid det tager at opvarme mælken. Fjern asken fra
askevarmeren, når den tid, som er angivet i
referencetabellen for ekspresopvarmning, er gået (Fig. 8).
Tip: Hvis du ikke synes, at mælken er varm nok, kan du stille
asken tilbage i apparatet til ekstra opvarmning i højst 30
sekunder. Dette vil give et lidt varmere resultat, men uden
overophedning.
Forsigtig: Hvis du efterlader asken i askevarmeren i
længere tid end den angivne tid i indstillingstabellen,
risikerer du, at mælken bliver overophedet.
DANSK22
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98

Avent AVENT SCF355/00 Användarmanual

Kategori
Flaskvärmare
Typ
Användarmanual