Form ZCE779A 2 Date 2017March2/B
Air hoses that are not oil resistant or are not rated for the working pressure can burst.
Make sure that all air hoses are oil resistant and rated for the working pressure.
Air hoses that burst can cause injury.
Tools not operated at proper air pressure can operate erratically.
Do not exceed a maximum air pressure of 90 psig/6.2 bar or as stated on the tool’s nameplate or operating instructions. Use an
air regulator to maintain proper air pressure.
Erratic operation in power tools can cause injury.
Improperly repaired tools perform unpredictably.
Repair tools at an Authorized Sioux Service Center.
Tools that perform unpredictably can cause injury.
Tools left connected to the air supply can start unexpectedly.
Always remove tool from air supply and activate trigger to bleed air line before making any adjustments, changing accessories,
or doing any maintenance or service on tool. Make it a habit to check to see that all adjusting keys and wrenches have been
removed from tool before turning it on.
Tools starting unexpectedly and flying keys and wrenches can cause injury.
Working in poorly lit areas makes it hard to see hazards.
Keep work area well lit.
Poorly lit work areas can cause injury.
Children are attracted to work areas.
Keep children away. All visitors must keep a safe distance away from work area.
Children in work areas can be injured.
Unauthorized or untrained personnel can misuse unattended tools.
Store idle tools in a dry, high or locked-up place, out of the reach of children.
Misused tools can cause injury.
Tools with the actuator left in the “ON” position when an unexpected air pressure loss occurs can start unexpectedly when the air
pressure is restored.
Release the actuator if an unexpected loss of air pressure occurs.
Unexpected tool starts can cause injury.
Tools with the actuator left in the “on” position can cause unexpected starts when the tool is connected to the air supply.
Be sure actuator is off before hooking up air.
Unexpected starts can cause injury.
The use of any accessory with this tool not provided or specified by Sioux Tools can perform unpredictably.
Use only accessories provided or specified by Sioux Tools.
Tools that perform unpredictably can cause injury.
Read and understand safety instructions before installing, operating, repairing, maintaining, changing accessories on, or
working near the skin clamp runner. Do not modify this skin clamp runner. Do not operate this skin clamp runner if it has been
modified or damaged. Tools should be inspected periodically to ensure markings are legible.
Beware of hazards during operation of the skin clamp runner.
Wear gloves to protect from cuts, abrasion and heat. Operators and maintenance personnel should be physically able to handle
the bulk, weight and power of the tool. Hold the tool firmly and be ready to counteract normal or sudden movements and have both
hands available. Maintain a balanced body position and secure footing. Use a suspension device or side handles when possible.
Keep hands away from the rotating chuck and drill bit. Release the start-and-stop device in case of an interruption of air supply.
Use only lubricants recommended by Sioux Tools. Safety glasses are required; gloves and protective clothing are recommended.
Hazards from operating the tool can cause injury.
Operators can experience discomfort in the hands, arms, shoulders, neck or other parts of the body.
Use a comfortable, not off-posture position. Change posture during extended tasks.
If the operator experiences persistent or recurring discomfort, pain, throbbing, aching, tingling, numbness, burning sensations or
stiffness, the operator should seek medical assistance.
Accessories and bits attached to the skin clamp runner can create hazards.
Disconnect the skin clamp runner from the air supply before changing the inserted tool or accessories. Do not touch the
inserted bit during operation as this increases the risk of cuts, burns, or vibration injuries. Do not use accessories and
consumables that are not recommended by Sioux Tools. Use only the sizes and types of accessories and bits that are
recommended by Sioux Tools.
Improper accessories, improperly mounted accessories and tools can cause injury.
Be aware of hazards from your workplace.
Be aware of slippery surfaces caused by the use of the tool and avoid trip hazards caused by the air line. Proceed with care in
unfamiliar surroundings. The screwdriver should not be used in explosive atmospheres and is not insulated against contact
with electrical current. Ensure work area is free from electrical cables, gas pipes and other hazards.
Hazards from your workplace can cause injuries.
When disposing of a tool, do it in a way that does not harm personnel or the environment.
INTENDED USE AND GENERAL OPERATION
This tool is used to install skin clamps that temporarily hold components together. Skin clamps are often called by other names, such as “Cleco
clamps®”, “Kwick-Loc®”, “Wedgelok®”, and sheet metal holders. To install skin clamps, place the nose piece of the tool over the outer body of skin
clamp. Engage the tool driver on the threaded 1/4” (6.4 mm) nut of the skin clamp. Pull the trigger and run the tool until it stalls. To remove the skin
clamp, follow the above procedure, but reverse the rotation of the tool.
REVERSE OPERATION
The spindle rotation is controlled by the slide on the top, rear of the tool.
Move the slide to the right for right hand rotation and to the left for left hand rotation. To ensure maximum performance, make sure the slide is in the full
left or right position.
AIR SUPPLY
The efficiency and life of this tool depend on the proper supply of clean, dry air at a maximum of 90 PSI. The use of an air line filter, pressure regulator,
and lubricator is recommended.
Before connecting to tools, blow out the air line to remove water and dirt that may have accumulated.