Optional Boards
for
DSP UNIT
T
hank you for choosing the board for Yamaha DSP1D (DSP unit).
Ask an authorized Yamaha service engineer to install the board. Do not install the board yourself.
The following items are optional boards available for the DSP1D.
INPUT DSP BOARD IDB1D
CONSOLE INTERFACE BOARD CIB1D
ENGINE MANAGEMENT BOARD EMB1D
PATCH DSP BOARD PDB1D
GROUP DSP BOARD GDB1D
EFFECT DSP BOARD EDB1D
■ Installing the board (For only an authorized Yamaha service engineers)
Before installing the board, be sure to turn off the power to the DSP1D and disconnect the power cord.
You need to remove the front cover of the DSP1D to install any board. To install the PDB1D board, you also need to remove the
left side cover.
1. Remove ten screws as
shown in the picture. Do
not remove any other
screws. Keep the re-
moved screws in a safe
place since you will need
them to re-attach the
cover.
2. As shown in the picture,
remove the cover by
opening from the right
side to avoid damage to
the hardware on the left
side of the rack.
front cover
hardware on the left side of the rack
2
6. Slide the board into the
slot along the upper and
lower guide rails.
The sliding position is la-
belled with the corre-
sponding board model
name.
3. Loosen two screws on the
protect bar.
4. Lift up the protect bar and
remove it.
5. If you are replacing the
PDB1D board and the
GDB1D board, remove
two connecting ribbon
cables.
7. Press both edges of the
board firmly and slide the
board all the way into the
slot.
Reverse these steps to re-
install the protect bar and
the front cover.
3
1. Remove the unit front cover as
described in the previous pro-
cedure. Remove two ribbon
cables from the board.
<Installing the PDB1D board>
3. Remove six ribbon cables
from the board. At this
time, mark the ribbon
cables so that you can
identify each of them and
re-connect them correctly
later.
2. Remove eight fixing screws
on the rack mount hardware,
and remove the rack mount
hardware. Do not remove any
screws or hardware other than
those shown in the picture.
Remove twelve screws on the
left side cover, then remove
it. Note that the screws for the
rack mount hardware are dif-
ferent from the screws on the
side cover.
4. Remove the PDB1D board. At
this time, care should be taken
so that the board will not catch
the ribbon cable.
After replacing it with a new
board, follow the steps de-
scribed previously to re-install
the ribbon cables, side cover,
rack mount hardware, and
front cover.
ADVARSEL!
Lithiumbatteri—Eksplosionsfare ved fejlagtig
håndtering. Udskiftning må kun ske med batteri
af samme fabrikat og type. Levér det brugte
batteri tilbage til leverandoren.
VARNING
Explosionsfara vid felaktigt batteribyte. Använd
samma batterityp eller en ekvivalent typ som
rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti
asennettu. Vaihda paristo ainoastaan
laitevalmistajan suosittelemaan tyyppiin. Hävitä
käytetty paristo valmistajan ohjeiden
mukaisesti.
NEDERLAND THE NETHERLANDS
● Dit apparaat bevat een lithium batterij voor geheugen
back-up.
● Raadpleeg uw leverancier over de verwijdering van de
batterij op het moment dat u het apparaat ann het einde
van de levensduur afdankt of de volgende Yamaha Service
Afdeiing:
Yamaha Music Nederland Service Afdeiing
Kanaalweg 18-G, 3526 KL UTRECHT
Tel. 030-2828425
● Gooi de batterij niet weg, maar lever hem in als KCA.
● This apparatus contains a lithium battery for memory
back-up.
● For the removal of the battery at the moment of the
disposal at the end of the service life please consult your
retailer or Yamaha Service Center as follows:
Yamaha Music Nederland Service Center
Address: Kanaalweg 18-G, 3526 KL
UTRECHT
Tel: 030-2828425
● Do not throw away the battery. Instead, hand it in as small
chemical waste.
The above statements apply only to the IDB1D board.
YAMAHA CORPORATION
V510760 R1 1 IP 4 Pro Audio & Digital Musical Instrument Division
P.O. Box 3, Hamamatsu, 430-8651, Japan
00 06 300 AP Printed in Japan
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly
approved by Yamaha may void your authority,
granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the
USA.
3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC Regu-
lations, Part 15 for Class “B” digital devices. Com-
pliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result
in harmful interference with other electronic
devices. This equipment generates/uses radio fre-
quencies and, if not installed and used according
to the instructions found in the users manual, may
cause interference harmful to the operation of
other electronic devices. Compliance with FCC
regulations does not guarantee that interference
will not occur in all installations. If this product is
found to be the source of interference, which can
be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of
the following measures:
Relocate either this product or the device that is
being affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line fil-
ter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300
ohm ribbon lead, change the lead-in to co-axial
type cable.
If these corrective measures do not produce satis-
factory results, please contact the local retailer
authorized to distribute this type of product. If you
can not locate the appropriate retailer, please con-
tact Yamaha Corporation of America, Electronic
Service Division, 6600 Orangethorpe Ave, Buena
Park, CA90620
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its
subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
FCC INFORMATION (U.S.A.)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
-
1
-
2
-
3
-
4
-
5
Yamaha EDB1D Bruksanvisning
- Typ
- Bruksanvisning
på andra språk
- italiano: Yamaha EDB1D Manuale del proprietario
- čeština: Yamaha EDB1D Návod k obsluze
- español: Yamaha EDB1D El manual del propietario
- Deutsch: Yamaha EDB1D Bedienungsanleitung
- polski: Yamaha EDB1D Instrukcja obsługi
- português: Yamaha EDB1D Manual do proprietário
- français: Yamaha EDB1D Le manuel du propriétaire
- 日本語: Yamaha EDB1D 取扱説明書
- Türkçe: Yamaha EDB1D El kitabı
- English: Yamaha EDB1D Owner's manual
- dansk: Yamaha EDB1D Brugervejledning
- русский: Yamaha EDB1D Инструкция по применению
- Nederlands: Yamaha EDB1D de handleiding
- română: Yamaha EDB1D Manualul proprietarului