Simplicity 106232-0111-H1 Användarmanual

varumärke: Simplicity

Modell: 106232-0111-H1

Kategori: Tillbehör till motorfordon

Typ: Användarmanual

Denna manual är också lämplig för

English

es fr

Español Français

deda el it nonl pt svfi

Dansk Norsk SvenskaDeutsch Suomi NederlandsItaliano

ÅëëçíéêÜ

Português

Operator’s Manual

Betjeningsvejledning

Bedienungsanleitung

Åã÷åéñßäéï ×ñÞóçò

Manual del Operario

Käyttäjän käsikirja

Manuel de l’opérateur

Manuale dell’Operatore

Gebruiksaanwijzing

Brukerhåndbok

Manual do Operador

Instruktionsbok

Form No. 380407WST

Revision: B

Model 106200

750 Seriest

I/C

750 Seriest

Intekt Pro 750 Seriest

Briggs & Stratton is a registered trademark

of Briggs & Stratton Corporation.

Not for

Reproduction

BRIGGSandSTRATTON.COM

Not for

Reproduction

Not for

Reproduction

4 BRIGGSandSTRATTON.COM

General Information

This manual contains safety information to make you aware of the hazards and risks

associated with engines and how to avoid them. It also contains instructions for the

proper use and care of the engine. Because Briggs & Stratton Corporation does not

necessarily know what equipment this engine will power, it is important that you read and

understand these instructions and the instructions for the equipment. Save these

original instructions for future reference.

For replacement parts or technical assistance, record below the engine model, type, and

code numbers along with the date of purchase. These numbers are located on your

engine (see the Features and Controls page).

Date of purchase:

Engine model:

MM/DD/YYYY

Model: Code:Ty pe:

Power Rating

The gross power rating for individual gas engine models is labeled in accordance with

SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque

Rating Procedure), and rating performance has been obtained and corrected in

accordance with SAE J1995 (Revision 2002--05). Torque values are derived at 3060

RPM; horsepower values are derived at 3600 RPM. The gross power curves can be

viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with exhaust

and air cleaner installed whereas gross power values are collected without these

attachments. Actual gross engine power will be higher than net engine power and is

affected by, among other things, ambient operating conditions and engine--to--engine

variability. Given the wide array of products on which engines are placed, the gas engine

may not develop the rated gross power when used in a given piece of power equipment.

This difference is due to a variety of factors including, but not limited to, the variety of

engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.),

application limitations, ambient operating conditions (temperature, humidity, altitude), and

engine--to--engine variability.

Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an

engine of higher rated power for this Series engine.

Operator Safety

Explosion

Toxic Fumes

Moving Parts

Shock

Hot Surface

Kickback

Fire

Fuel Shutoff

Read Manual

Choke

Oil

Fuel

On Off

Stop

Wear Eye

Protection

Slow

Fast

SAFETY AND CONTROL SYMBOLS

Hazardous

Chemical

Frostbite

The safety alert symbol is used to identify safety information about hazards that can

result in personal injury . A signal word (DANGER, WARNING, or CAUTION) is used with the

alert symbol to indicate the likelihood and the potential severity of injury . In addition, a hazard

symbol may be used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in death or

serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or

serious injury.

CAUTION indicates a hazard which, if not avoided, could result in minor or

moderate injury.

NOTICE indicates a situation that could result in damage to the product.

WARNING

Certain components in this product and its related accessories contain chemicals

known to the State of California to cause cancer, birth defects, or other reproductive

harm. Wash hands after handling.

WARNING

The engine exhaust from this product contains chemicals known to the State of

California to cause cancer, birth defects, or other reproductive harm.

WARNING

Briggs & Stratton Engines are not designed for and are not to be used to power:

fun-karts; go-karts; children’s, recreational, or sport all-terrain vehicles (ATVs);

motorbikes; hovercraft; aircraft products; or vehicles used in competitive events not

sanctioned by Briggs & Stratton. For information about competitive racing products,

see www.briggsracing.com. For use with utility and side-by-side ATVs, please contact

Briggs & Stratton Engine Application Center, 1-866-927-3349. Improper engine

application may result in serious injury or death.

NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start

the engine, make sure you add oil according t o the instructions in this manual. If you

start the engine without oil, it will be damaged beyond repair and will not be covered

under warranty.

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

 Turn engine off and let engine cool at least 2 minutes before removing the fuel

cap.

 Fill fuel tank outdoors or in well-ventilated area.

 Do not over fill fuel tank. To allow for expansion of the fuel, do not fill above the

bottom of the fuel tank neck.

 Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

 Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary

 If fuel spills, wait until it evaporates before starting engine.

When Starting Engine

 Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in

place and secured.

 Do not crank engine with spark plug removed.

 If engine floods, set choke (if equipped) to OPEN/RUN position, move throttle

(if equipped) to FAST position and crank until engine starts.

When Operating Equipment

 Do not tip engine or equipment at angle which causes fuel to spill.

 Do not choke the carburetor to stop engine.

 Never start or run the engine with the air cleaner assembly (if equipped) or the

air filter (if equipped) removed.

When Changing Oil

 When you drain the oil from the top oil fill tube, the fuel tank must be empty or

fuel can leak out and result in a fire or explosion.

When Tipping Unit for Maintenance

 When performing maintenance that requires the unit to be tipped, the fuel tank

must be empty or fuel can leak out and result in a fire or explosion.

When Transporting Equipment

 Transport with fuel tank EMPTY or with fuel shut-off valve OFF.

When Storing Fuel Or Equipment With Fuel In Tank

 Store away from furnaces, stoves, water heaters or other appliances that have

pilot lights or other ignition sources because they can ignite fuel vapors.

Not for

Reproduction

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

WARNING

 If there is natural or LP gas leakage in area, do not start engine.

 Do not use pressurized starting fluids because vapors are flammable.

Engines give off carbon monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea, fainting or death.

WARNING

 Start and run engine outdoors.

 Do not start or run engine in enclosed area, even if doors or windows are open.

Rapid retraction of starter cord (kickback) will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

WARNING

 When starting engine, pull the starter cord slowly until resistance is felt and then

pull rapidly to avoid kickback.

 Remove all external equipment/engine loads before starting engine.

 Direct-coupled equipment components such as, but not limited to, blades,

impellers, pulleys, sprockets, etc., must be securely attached.

Rotating parts can contact or entangle hands, feet, hair, clothing, or

accessories.

Traumatic amputation or severe laceration can result.

WARNING

 Operate equipment with guards in place.

 Keep hands and feet away from rotating parts.

 Tie up long hair and remove jewelry.

 Do not wear loose-fitting clothing, dangling drawstrings or items that could

become caught.

Running engines produce heat. Engine parts, especially muffler,

become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch fire.

WARNING

 Allow muffler, engine cylinder and fins to cool before touching.

 Remove accumulated debris from muffler area and cylinder area.

 It is a violation of California Public Resource Code, Section 4442, to use or

operate the engine on any forest-covered, brush-covered, or grass-covered land

unless the exhaust system is equipped with a spark arrester, as defined in

Section 4442, maintained in effective working order. Other states or federal

jurisdictions may have similar laws. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Fire hazard

WARNING

Before performing adjustments or repairs:

 Disconnect the spark plug wire and keep it away from the spark plug.

 Disconnect battery at negative terminal (only engines with electric start.)

 Use only correct tools.

 Do not tamper with governor spring, links or other parts to increase engine

speed.

 Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts may not perform as well, may damage

the unit, and may result in injury.

 Do not strike the flywheel with a hammer or hard object because the flywheel

may later shatter during operation.

When testing for spark:

 Use approved spark plug tester.

 Do not check for spark with spark plug removed.

Not for

Reproduction

6 BRIGGSandSTRATTON.COM

Features and Controls

Compare the illustration

with your engine to familiarize yourself with the location of

various features and controls.

A. Engine Identification

Model Type Code

B. Spark Plug

C. Air Cleaner

D. Choke

E. Starter Cord Handle

F. Finger Guard

G. Throttle Control (optional)

H. Stop Switch (optional)

I. Fuel Tank and Cap

J. Oil Drain Plug

K. Oil Fill

L. Muffler

Muffler Guard

Spark Arrester (optional)

Muffler Deflector (optional)

M. Fuel Shutoff

Operation

Oil c apacity (see the Specifications section)

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty Certified oils for best

performance. Other high-quality detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for the engine. Use t he chart to

select the best viscosity for the outdoor temperature range expected.

* Below 40°F(4°C) the use of SAE 30 will result in hard starting.

** Above 80°F(27°C) the use of 10W-30 may cause increased oil consumption. Check

oil level more frequently.

How To Check/Add Oil - Figure

Before adding or checking the oil

 Place engine level.

 Clean the oil fill area of any debris.

1. Remove the dipstick (A) and wipe with a clean cloth.

2. Insert the dipstick. Do not turn or tighten.

3. Remove the dipstick and check the oil level. I t should be at the top of the full indicator

(B) on the dipstick.

4. To add oil, pour the oil slowly into the engine oil fill (C). Fill to point of overflowing.

5. Replace and tighten the dipstick.

Oil Pressure

If the oil pressure is too low, a pressure switch (if equipped) will either stop the engine or

activate a warning device on the equipment. If this occurs, stop the engine and check the

oil level with the dipstick.

If the oil level is below the ADD mark, add oil until it reaches the FULL mark. Start the

engine and check for proper pressure before continuing to operate.

If the oil level is between the ADD and FULL marks, do not start the engine. Contact an

Authorized Briggs & Stratton Dealer to have t he oil pressure problem corrected.

Fuel Recommendations

Fuel must meet these requirements:

 Clean, fresh, unleaded gasoline.

 A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.

 Gasoline with up to 10% ethanol is acceptable.

CAUTION: Do not use unapproved gasolines, s uch as E15 and E85. Do not mix oil in

gasoline or modify the engine to run on alternate fuels. Use of unapproved fuels will

damage the engine components and void the engine warranty.

To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel. See

Storage. All fuel is not the same. If starting or performance problems occur, change fuel

providers or c hange brands. This engine is certified to operate on gasoline. The

emissions control system for this engine is EM (Engine Modifications).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON)

gasoline is acceptable. To remain emissions compliant, high altitude adjustment is

required. Operation without this adjustment will cause decreased performance,

increased fuel consumption, and increased emissions. See an authorized Briggs &

Stratton Dealer for high altitude adjustment information.

Operation of the engine at altitudes below 2,500 feet (762 meters) with the high altitude

kit is not recommended.

How To Add Fuel - Figure

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

 Turn engine off and let engine cool at least 2 minutes before removing the fuel

cap.

 Fill fuel tank outdoors or in well-ventilated area.

 Do not over fill fuel tank. To allow for expansion of the fuel, do not fill above the

bottom of the fuel tank neck.

 Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

 Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary

 If fuel spills, wait until it evaporates before starting engine.

1. Clean the fuel cap area of dirt and debris. Remove the fuel cap (A) (Figure 3).

2. Fill the fuel tank (B) with fuel. To allow for expansion of the fuel, do not fill above the

bottom of the fuel tank neck (C).

3. Reinstall the fuel cap.

How To Start The Engine - Figure

Rapid retraction of starter cord (kickback) will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

WARNING

 When starting engine, pull the starter cord slowly until resistance is felt and then

pull rapidly to avoid kickback.

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Starting Engine

 Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in

place and secured.

 Do not crank engine with spark plug removed.

 If engine floods, set choke (if equipped) to OPEN/RUN position, move throttle

(if equipped) to FAST position and crank until engine starts.

Not for

Reproduction

Engines give off carbon monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea, fainting or death.

WARNING

 Start and run engine outdoors.

 Do not start or run engine in enclosed area, even if doors or windows are open.

NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start

the engine, make sure you add oil according t o the instructions in this manual. If you

start the engine without oil, it will be damaged beyond repair and will not be covered

under warranty.

Note: Equipment may have remote controls. See the equipment manual for location and

operation of remote controls.

1. Check the oil level. See the How To Check/Add Oil section.

2. Make sure equipment drive controls, if equipped, are disengaged.

3. Move the fuel shutoff (E) to the on position.

4. Move the choke control lever (A) to the choke

position (Figure 4).

Note: Choke is usually unnecessary when restarting a warm engine.

5. Move the throttle control lever (B), if equipped, to the fast

position. Operate

the engine with the throttle control lever in the fast position.

6. On engines equipped with a stop switch (C), move the switch to the on position.

7. Firmly hold the starter cord handle (D). Pull the starter cord handle slowly until

resistance is felt, then pull rapidly.

Note: If the engine does not start after repeated attempts, go to

BRIGGSandSTRATTON.COM or call 1-800-233-3723 (in USA).

WARNING: Rapid retraction of the starter cord (kickback) will pull your

hand and arm toward the engine faster than you can let go. Broken bones, fractures,

bruises or sprains could result. When starting engine, pull the starter cord slowly until

resistance is felt and then pull rapidly to avoid kickback.

8. As the engine warms up, move the c hoke control (A)totherun position.

How To Stop The Engine - Figure

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

 Do not choke the carburetor to stop engine.

1. Move the stop switch (C), if equipped, to the stop position.

Move the throttle control lever (B), if equipped, to slow

and then to the stop

position.

2. Move the fuel shutoff (E) to the off position.

Maintenance

We recommend that you see any Briggs & Stratton Authorized Dealer for all

maintenance and service of the engine and engine parts.

NOTICE: All the components used to build this engine must remain in place for proper

operation.

WARNING: When performing maintenance that requires the unit to be

tipped, the f uel tank must be empty or fuel can leak out and result in a fire or

explosion.

Emissions Control

Maintenance, replacement, or repair of the emissions control devices and systems

may be performed by any non-road engine repair establishment or individual.

However, to obtain “no charge” emissions control service, the work must be performed

by a f actory authorized dealer. See the Emissions Warranty.

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Fire hazard

WARNING

Before performing adjustments or repairs:

 Disconnect the spark plug wire and keep it away from the spark plug.

 Disconnect battery at negative terminal (only engines with electric start.)

 Use only correct tools.

 Do not tamper with governor spring, links or other parts to increase engine

speed.

 Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts may not perform as well, may damage

the unit, and may result in injury.

 Do not strike the flywheel with a hammer or hard object because the flywheel

may later shatter during operation.

When testing for spark:

 Use approved spark plug tester.

 Do not check for spark with spark plug removed.

Maintenance Chart

First 5 Hours

 Change oil

Every8HoursorDaily

 Check engine oil level

 Clean area around muffler and controls

 Clean finger guard

Every 25 Hours or Annually

 Clean air filter *

 Clean pre-cleaner *

Every 50 Hours or Annually

 Change engine oil

 Inspect muffler and spark arrester

Annually

 Replace air filter

 Replace pre-cleaner

 Replace spark plug

 Clean air cooling system *

* In dusty conditions or when airborne debris is present, clean more often.

Carburetor Adjustment

Never make adjustments to the carburetor. The carburetor was set at the factory to

operate efficiently under most conditions. However, if adjustments are required, see any

Briggs & Stratton Authorized Dealer for service.

NOTICE: The manufacturer of t he equipment on which this engine is installed specifies

the top speed at which the engine will be operated. Do not exceed this speed.

Not for

Reproduction

BRIGGSandSTRATTON.COM

How To Replace The Spark Plug - Figure

Check the gap (A, Figure 5) with a wire gauge (B). If necessary, reset the gap. Install

and tighten the spark plug to the recommended torque. For gap setting or torque, see the

Specifications section.

Note: In some areas, local law requires using a resistor spark plug to suppress ignition

signals. If this engine was originally equipped with a resistor spark plug, use the same

type for replacement.

Inspect Muffler And Spark Arrester - Figure