DSP
PRO LOGIC
TAPE
MONITOR
PROGRAM EFFECT
NATURAL SOUND DIGITAL SOUND FIELD PROCESSOR
/
AMPLIFIER DSP-E580
D
D
S
S
P
P
-
-
E
E
5
5
8
8
0
0
CONTENTS
PRECAUTIONS & SAFETY INSTRUCTIONS ....................Inside Front Cover
SETUP & ADJUSTMENT..................................................................................3
1-1. GETTING STARTED.................................................................................3
1-2. SETUP.......................................................................................................8
1-3. CONTROLS & ADJUSTMENTS.............................................................18
1-4. ADJUSTMENT.........................................................................................21
GENERAL OPERATION.................................................................................24
2-1. PLAYING A SOURCE.............................................................................24
2-2. DIGITAL SOUND FIELD PROGRAMS ..................................................25
2-3. SELECTING SOUND FIELD PROGRAMS............................................25
2-4. MUTING THE EFFECT SOUND ............................................................25
2-5. SUPERIMPOSED VIDEO PROGRAM/PARAMETER
DISPLAY..................................................................................................25
2-6. DESCRIPTIONS OF THE SOUND FIELD PROGRAMS......................26
CREATING YOUR OWN SOUND FIELDS....................................................30
3-1. SELECTING AND EDITING PROGRAM PARAMETERS ....................30
3-2. DESCRIPTIONS OF THE DIGITAL SOUND FIELD
PARAMETERS........................................................................................32
TROUBLESHOOTING ....................................................................................34
SPECIFICATIONS...........................................................................................35
OPERATION MANUAL
DIGITAL SOUND FIELD PROCESSING AMPLIFIER
1 Read Instructions – All the safety
and operating instructions should be read
before the unit is operated.
2 Retain Instructions – The safety and
operating instructions should be retained
for future reference.
3 Heed Warnings – All warnings on the
unit and in the operating instructions
should be adhered to.
4 Follow Instructions – All operating
and other instructions should be followed.
5 Water and Moisture – The unit
should not be used near water – for
example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet
basement, or near a swimming pool, etc.
6 Carts and Stands – The unit should
be used only with a cart or stand that is
recommended by the manufacturer.
6A A unit and cart combination should
be moved with care. Quick
stops, excessive force, and
uneven surfaces may
cause the unit and cart
combination to overturn.
7 Wall or Ceiling Mounting – The unit
should be mounted to a wall or ceiling
only as recommended by the
manufacturer.
8 Ventilation – The unit should be
situated so that its location or position
does not interfere with its proper
ventilation. For example, the unit should
not be situated on a bed, sofa, rug, or
similar surface, that may block the
ventilation openings; or placed in a built-
in installation, such as a bookcase or
cabinet that may impede the flow of air
through the ventilation openings.
9 Heat – The unit should be situated
away from heat sources such as
radiators, stoves, or other appliances that
produce heat.
10 Power Sources – The unit should be
connected to a power supply only of the
type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-
supply cords should be routed so that
they are not likely to be walked on or
pinched by items placed upon or against
them, paying particular attention to cords
at plugs, convenience receptacles, and
the point where they exit from the unit.
12 Cleaning – The unit should be
cleaned only as recommended by the
manufacturer.
13 Nonuse Periods – The power cord of
the unit should be unplugged from the
outlet when left unused for a long period
of time.
14 Object and Liquid Entry – Care
should be taken so that objects do not fall
into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The
unit should be serviced by qualified
service personnel when:
A. The power-supply cord or the plug
has been damaged;
or
B. Objects have fallen, or liquid has
been spilled into the unit;
or
C. The unit has been exposed to rain;
or
D. The unit does not appear to operate
normally or exhibits a marked change in
performance;
or
E. The unit has been dropped, or the
cabinet damaged.
16 Servicing – The user should not
attempt to service the unit beyond those
means described in the operating
instructions. All other servicing should be
referred to qualified service personnel.
17 Power Lines – An outdoor antenna
should be located away from power lines.
18 Grounding or Polarization –
Precautions should be taken so that the
grounding or polarization is not defeated.
SAFETY INSTRUCTIONS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK), NO USER-SERVICEABLE
PARTS INSIDE, REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
•
Explanation of Graphical Symbols
CAUTION
IMPORTANT!
Please record the serial number of this
unit in the space below.
Model:
Serial No.:
The serial number is located on the rear
of the unit.
Retain this Owner’s Manual in a safe
place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
PRECAUTIONS & SAFETY INSTRUCTIONS
1
1 To ensure the finest performance,
please read this manual carefully. Keep it in
a safe place for future reference.
2 Install your unit in a cool, dry, clean
place – away from windows, heat sources,
and too much vibration, dust, moisture or
cold. Avoid sources of hum (transformers,
motors). To prevent fire or electrical shock,
do not expose to rain and water.
3 Do not operate the unit upside-down. It
may overheat, possibly causing damage.
4 Never open the cabinet. If a foreign
object drops into the set, contact your
dealer.
5 Do not use force on switches, knobs or
cords. When moving the set, first turn the
unit off. Then gently disconnect the power
plug and the cords connecting to other
equipment. Never pull the cord itself.
6 Do not attempt to clean the unit with
chemical solvents; this might damage the
finish. Use a clean, dry cloth.
7 Always set the volume control to “–
∞
”
while lowering the tonearm to play a record;
turn the volume up with the stylus in the
groove.
8 Be sure to read the “Troubleshooting”
section on common operating errors before
concluding that your unit is faulty.
9 Do not connect audio equipment to the
AC outlets on the rear panel if that
equipment requires more power than the
outlets are rated to provide.
We Want You Listening
For A Lifetime
YAMAHA and the Electronic Industries
Association’s Consumer Electronics
Group want you to get the most out of
your equipment by playing it at a safe
level. One that lets the sound come
through loud and clear without annoying
blaring or distortion – and, most
importantly, without affecting your
sensitive hearing. Since hearing damage
from loud sounds is often undetectable
until it is too late, YAMAHA and the
Electronic Industries
Association’s Consumer
Electronics Group
recommend you to avoid
prolonged exposure from
excessive volume levels.
PRECAUTIONS
FCC INFORMATION
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this
manual, meets FCC requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT : When connecting this product to accessories and/or another
product use only high quality shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions. Failure to follow instructions
could void your FCC authorization to use this product in the USA.
3. NOTE : This product has been tested and found to comply with the requirements
listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of assurance that your use of
this product in a residential environment will not result in harmful interference
with other electronic devices.
This equipment generates/uses radio frequencies and, if not installed and used
according to the instructions found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that interference will not
occur in all installations. If this product is found to be the source of interference,
which can be determined by turning the unit “OFF” and “ON”, please try to
eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the
interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits
or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the
antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type
cable.
If these corrective measures do not produce satisfactory results, please contact
the local retailer authorized to distribute this type of product. If you can not
locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A.
6660 Orangethorpe Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products distributed by Yamaha
Corporation of America or its subsidiaries.
2
Congratulations!
You are the proud owner of a Yamaha Digital Sound Field Processing (DSP) System—an
extremely sophisticated audio component. The DSP system takes full advantage of Yamaha’s
undisputed leadership in the field of digital audio processing to bring you a whole new world
of listening experiences. Follow the instructions in this manual carefully when setting up your
system, and the DSP system will sonically transform your room into a wide range of listening
environments—anything from a famous concert hall to a cozy jazz club. In addition, you get
incredible realism from Dolby-Surround encoded video sources using the built-in Dolby Pro
Logic Surround Decoder.
Rather than tell you about the wonders of digital sound field processing, however, let’s get
right down to the business of setting up the system and trying out its many capabilities.
Please read this operation manual carefully and store it in a safe place for later reference.
1-1. GETTING STARTED
Unpacking
If you haven’t already done so, carefully remove this unit and its
accessories from the box and wrapping material. You should find the
unit itself and the following accessories.
Installing the Remote Control Unit Batteries
Since the remote control unit will be used for many of this unit’s
control operations, you should begin by installing the supplied
batteries.
1. Turn the remote control unit over and slide the battery
compartment cover downward in the direction of the arrow.
2. Insert the batteries (R6, AA, UM-3 type), being careful to align
them with the polarity markings on the inside of the battery
compartment.
3. Close the battery compartment cover.
3
SETUP & ADJUSTMENT
Remote control
Batteries
2
3
1
Pin cable, audio x 2 Pin cable, video
1
2
3
●
When you notice that remote control operation has become
erratic, or the distance from which the remote control will function
has decreased, it’s time to replace the batteries. Always replace
all batteries at the same time.
●
This remote control uses an advanced, highly directional infrared
beam. Be sure to aim the remote control directly at the remote
control sensor on the main unit when operating.
Remote control transmitter operation range
Notes
●
There should be no large obstacles between the remote
control transmitter and the main unit.
●
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter to work
incorrectly. In this case, reposition the main unit to avoid
direct lighting.
Digital Sound Field Processing
What is it that makes live music so good? Today’s advanced
sound reproduction technology lets you get extremely close to the
sound of a live performance, but chances are you’ll still notice
something missing, the acoustic environment of the live concert hall.
Extensive research into the exact nature of the sonic reflections that
create the ambience of a large hall has made it possible for Yamaha
engineers to bring you this same sound in your own listening room,
so you’ll feel all the sound of a live concert. What’s more, our
technicians, armed with sophisticated measuring equipment, have
even made it possible to capture the acoustics of a variety of actual
concert halls, jazz clubs, theaters, etc. from around the world, to
allow you to accurately recreate any one of these live performance
environments, all in your own home.
4
30°
30°
Remote control
sensor
Within approximately
7 m (23 feet)
Dolby Pro Logic Surround
The Dolby Pro Logic Surround Decoder program lets you
experience the dramatic realism and impact of Dolby Surround movie
theater sound in your own home. Dolby Pro Logic gets its name from
its professional-grade steering logic circuitry, which provides greater
effective channel separation for a much higher degree of realism than
the “passive” Dolby Surround circuits found in today’s typical home
audio/video equipment. Dolby Pro Logic Surround provides a true
center channel, so that there are four independent channels, unlike
passive Dolby Surround, which has in effect only three channels: left,
right, and rear. This center channel allows listeners seated in even
less-than-ideal positions to hear the dialog originating from the action
on the screen while experiencing good stereo imaging.
This Dolby Pro Logic Surround Decoder employs a digital signal
processing system. This system improves the stability of sound at
each channel and crosstalk between channels, so that positioning of
sounds around the room is more accurate compared with
conventional analog signal processing systems.
In addition, this unit features a built-in automatic input balance
control. This always assures you the best performance without
manual adjustment.
Manufactured under license from Dolby Laboratories Licensing
Corporation. Additionally licensed under one or more of the following
patents: U.S. number 3,959,590; Canadian numbers 1,004,603 and
1,037,877. “Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories Licensing Corporation.
Dolby Pro Logic Surround + DSP
Additionally you can enjoy sound environment created by the
combination of Dolby Pro Logic and YAMAHA DSP.
Precise sound
movement and orientation by the Dolby Pro Logic technology is
added to sound fields which are precisely recreated on the
basis of actual acoustic environments by the DSP technology,
so it is suitable for any Audio/Video source with video image.
This combination is used on sound field programs No.5 through
No.14, and No.16.
The YAMAHA “CINEMA DSP” logo indicates these programs
created by the combination of Dolby Pro Logic and YAMAHA DSP
technology.
5
Setting Up Your Speaker System
This unit has been designed to provide the best sound field
quality with a full five-speaker system setup, using one extra pairs of
effect speakers to generate the sound field plus one center speaker
for dialog, when using Dolby Pro Logic Surround decoding. We
therefore recommend that you use a five-speaker setup. A four-
speaker system using only one pair of effect speakers for the sound
field will still provide impressive ambience and effects, however, and
may be a good way to begin with this unit. You can always upgrade
to the full five speaker system later.
Use of the Center Dialog Speaker Is Recommended
With digital sound field programs No. 5 through No. 16, by using
either the Directional Enhancement circuit or the Dolby Pro Logic
decoder, decoded signals will be output from the center channel.
Therefore, if you want to upgrade the Audio/Video home theater
system, it is recommended to use the center speaker unit.
If for some reason it is not practical to use a center speaker, it is
possible to enjoy movie viewing without it. Best results, however, are
obtained with the full system.
It is also possible to further expand your system with the addition
of a subwoofer and amplifier. You may wish to choose the
convenience of a Yamaha Active Servo Processing Subwoofer
System, which has its own built-in power amp.
6
5 Speaker System
This is the recommended speaker
system, providing the best sound
effects.
With sound field programs No. 1
through No. 4, using effect speakers
reproduces the effective sound field.
With the sound field programs No. 5
through No. 16, the center speaker
provides precise center localization.
Center Mode—Set to NRML or WD.
(See page 23.)
4 Speaker System
Simple system without center
speaker.
With sound field programs No. 1
through No. 4, a sound effect matching
that of a 5-speaker system can be
obtained. With sound field programs No.
5 through No. 16, center sound is output
from the left and right main speakers.
Center Mode—Set to PHNTM.
(See page 23.)
Speakers and Speaker Placement
Your full five-speaker system will require two speaker pairs: the
MAIN SPEAKERS (your normal stereo speakers) and the REAR
EFFECT SPEAKERS, plus the CENTER SPEAKER. You may also
be using a subwoofer.
You will probably use your present stereo speakers as the MAIN
SPEAKER pair. The rear effect do not need to be equal with the
MAIN SPEAKERS, although the center speaker should be as close
as possible. They should have enough power handling capacity to
accept the maximum output of the DSP system or the external amps
that will drive them.
Place the MAIN SPEAKERS in the normal position.
Place the REAR EFFECT SPEAKERS behind your listening
position. They should be nearly six feet up from the floor.
Place the CENTER SPEAKER precisely between the two MAIN
SPEAKERS. (To avoid interference, keep the speaker above or
below the television monitor, or use a magnetically shielded speaker.)
If using a SUBWOOFER, such as a Yamaha Active Servo
Subwoofer System, the position of the speaker is not so critical
because low bass tones are not highly directional.
7
Main speaker Rear effect speaker Center speaker
8
1-2. SETUP
Before you start making connections make sure all related electronic components are turned OFF.
REAR PANEL
SINGLE
DUALDUAL
INPUT
TAPE
OUTPUT
SINGLE
AB
10dB 0dB
-
To AC outlet
15 7
9 D
2 3 4 6 8
0 A CB
(General Model)
1 Main Level Switch
Normally set to “0 dB”. If desired, you can decrease the main-
channel line output level at the MAIN OUTPUT jacks by 10 dB by
setting this switch to “–10 dB”.
2 Main Output Jacks
Main-channel line output. Connected to input jacks of external
stereo power amplifier (MAIN IN or AUX or TAPE PLAY jacks of
integrated amplifier or receiver).
3 Center Output Jack
Center-channel line output. Can be connected to input jack of an
external power amplifier driving the center speaker.
4 Rear Effect Output Jacks
Rear-channel line output. Can be connected to input jacks of an
external stereo power amplifier driving the rear effect speakers.
5 Center Speaker Terminals
When using the built-in center-channel amplifier, connect the
center speaker(s) here.
6 Rear Effect Speaker Terminals
When using the built-in rear-channel amplifier, connect the rear
effect speakers here.
7 Unswitched AC Outlet
You may plug another component into this socket as long as its
power consumption does not exceed the specified value
shown. “Unswitched” means that power is available even when
this unit is off.
8 Switched AC Outlet (U.S.A., Canada and General Model)
The power consumption of a component plugged into this
socket should not exceed the specified value shown.
“Switched” means that component is turned on and off by this
unit’s power switch.
9 Input Jacks
Accept input from a preamplifier, the “PRE OUT” or “TAPE REC”
outputs from an integrated amplifier, or direct input from a line-
level source.
0 Tape Rec Out and Playback Jacks
Connect the inputs and outputs of a stereo tape deck for
convenient recording and playback via this unit (the effect sound
cannot be recorded).
A Low Pass Jack
When using a subwoofer, connect its amplifier input to this jack.
Frequencies below 200 Hz from the left main, right main and
center channels are output to this jack.
B Video Superimpose Input/Output Jacks
Used to display this unit’s current operating status on your video
monitor, superimposed on the picture. Connect the VIDEO OUT
jack to the VIDEO IN jack of your monitor. Connect your
integrated amplifier or control amplifier equipped with video signal
output jacks or video signal source to the VIDEO IN jack.
Alternatively, the S VIDEO OUT and S VIDEO IN jacks can be
used for higher resolution and improved picture quality if your
monitor and video signal source are equipped with S connectors.
9
C Video NTSC/PAL Switch (General Model only)
Set this switch to the position corresponding to the standard
that your video equipment employs.
D Voltage Selector (General Model only)
Be sure to set to the line voltage in your area before applying
power. Consult your dealer if unsure of the correct setting.
NOTE: Even if an external power amplifier is connected to the REAR
or CENTER line output jacks, the corresponding internal amplifier will
not be turned off and output will be available at the speaker
terminals.
VIDEO SUPERIMPOSE
If you connect your video monitor to this unit and send video
signals to the video monitor via this unit, you can take advantage
of this unit’s capability to display program titles, parameter data
and information about other various settings and adjustments on
your video monitor’s screen. This information will be
superimposed over the video image.
If no video signal is input to this unit, the information will be
displayed over a blue colored background.
NOTE: The program titles, parameter data and other information
are also displayed on the display panel of this unit.
10
CONCERT HALL
DSP
P01 CONCERT HALL
CONNECTING AN INTEGRATED STEREO
AMPLIFIER OR STEREO RECEIVER TO THIS UNIT
Using an Integrated Amplifier or Stereo Receiver with PRE OUT
and MAIN IN Terminals
Some integrated amplifiers and stereo receivers have PRE OUT
and MAIN IN jacks which permit the preamplifier and power amplifier
sections to function independently. If your integrated amplifier or
stereo receiver has these jacks, begin by removing the jumpers that
connect the PRE OUT and MAIN IN jacks (or decouple the
preamplifier and power amplifier using the appropriate switch—refer
to your amplifier or receiver operation manual).
Connect the amplifier’s PRE OUT jacks to this unit’s INPUT jacks
with a stereo pin cable. Make sure that the “L” output from the
amplifier is connected to the “L” input on this unit, and that the “R”
output from the amplifier is connected to the “R” input on this unit.
Connect the MAIN OUTPUT jacks on this unit to the MAIN IN
jacks on your integrated amplifier or receiver with a second stereo pin
cable—making sure to connect the left and right channels correctly.
Connect the MAIN speakers to the speaker output terminals of your
integrated amplifier or receiver.
11
INPUT
TAPE
OUTPUT
10dB 0dB
-
MAIN
IN
PRE
OUT
Main Speaker L Main Speaker R
Integrated Amp
Using an Integrated Amplifier or Stereo Receiver that Does Not
Have PRE OUT and MAIN IN Terminals
If your integrated amplifier is NOT equipped with PRE OUT and
MAIN IN jacks, this unit must be connected to the amplifier or receiver
TAPE jacks. This unit provides additional TAPE PB and REC OUT
jacks so you will still have a place to connect your tape deck.
Connect the amplifier or receiver TAPE REC (or TAPE OUT) jacks
to this unit’s INPUT jacks with a stereo pin cable. Make sure that the
“L” output from the amplifier or receiver is connected to the “L” input
on this unit, and that the “R” output from the amplifier or receiver is
connected to the “R” input on this unit.
Connect the MAIN OUTPUT jacks on this unit to auxiliary (AUX)
input jacks, or the TAPE PLAY (or TAPE IN) jacks on your amplifier or
receiver with a second stereo pin cable—making sure to connect the
left and right channels correctly. Connect the MAIN speakers to the
speaker output terminals of the amplifier or receiver.
NOTE: If your system includes a tape deck which has been displaced
by connecting this unit to the TAPE jacks, reconnect your tape deck to
this unit’s TAPE PB and REC OUT jacks. REC OUT from this unit
goes to the INPUT jacks on your tape deck, and this unit’s TAPE PB
jacks should be connected to the tape deck’s OUTPUT jacks.
12
Main Speaker L
Main Speaker R
Integrated Amp
AUX or Tape Play (or Tape In)
INPUT
TAPE
OUTPUT
10dB 0dB
-
INPUTOUTPUT
Tape Rec or Tape Out
Tape Deck
CONNECTING A COMPONENT PREAMPLIFIER TO
THIS UNIT
Connect the PRE OUT jacks of the preamplifier (control amplifier)
to this unit’s INPUT jacks with a stereo pin cable. Make sure that the
“L” output from the preamplifier is connected to the “L” input on this
unit, and that the “R” output from the preamplifier is connected to the
“R” input on this unit.
Connect the MAIN OUTPUT jacks on this unit to the INPUT jacks
of a stereo power amplifier with a second stereo pin cable—making
sure to connect the left and right channels correctly. Connect the
MAIN speakers to the speaker output terminals of the power
amplifier.
13
Main Speaker L Main Speaker R
Control Amplifier
Power Amplifier
INPUT
TAPE
OUTPUT
10dB 0dB
-
INPUTPRE
OUT
CONNECTING TO VIDEO SIGNAL JACKS
If your integrated amplifier or similar component is equipped with
a video output jack, connect it to this unit’s VIDEO IN jack, and
connect this unit’s VIDEO OUT jack to the video input of your
monitor.
* If your integrated amplifier or similar component is not equipped
with any video output jack, connect the video output jack of your
video cassette recorder or another video source to this unit’s
VIDEO IN jack directly.
If your integrated amplifier, video cassette recorder, etc. and your
monitor are equipped with “S” (high-resolution) video terminals,
connect the “S” video output from your integrated amplifier or video
source to this unit’s S VIDEO IN jack, and connect this unit’s S
VIDEO OUT jack to the “S” video input of your monitor.
NOTE: If video signals are sent to both S VIDEO input and VIDEO
input jacks, the signals will be sent to their respective output jacks
independently.
NOTE: If your unit is the General Model, be sure the NTSC/PAL
switch has been correctly set to the standard that your video
equipment employs. U.S.A. and Canada models have no switch and
use the NTSC standard, while other models without a switch use the
PAL standard.
Notes about the Video superimpose
●
If you watch a video source which is connected to both S VIDEO
and VIDEO input jacks of this unit, signals of screen display
information are output from only the S VIDEO OUT jack.
●
When no video signal is input to either S VIDEO IN and VIDEO IN
jacks of this unit, signals of screen display information are output
from both S VIDEO OUT and VIDEO OUT jacks with a color
background.
* For the General Model, if the NTSC/PAL switch on the rear panel
is set to “PAL”, nothing will be output from either S VIDEO OUT or
VIDEO OUT jack in this case.
14
Integrated Amplifier etc.
Monitor TV
VIDEO
OUT
S VIDEO
OUT
VIDEO
IN
S VIDEO
IN
CONNECTING SPEAKER SYSTEMS
Connect the SPEAKERS terminals to your speakers with wire of
the proper gauge, cut as short as possible. If the connections are
faulty, no sound will be heard from the speakers. Make sure that the
polarity of the speaker wires is correct, that is, + and – markings are
observed. If these wires are reversed, the sound will be unnatural
and will lack bass. Do not let the bare speaker wires touch each
other or any other metal part as this could damage this unit and/or
speakers.
NOTE: Use speakers with the specified impedance shown on the
rear of this unit.
Red: positive (+)
Black: negative (–)
➀ Press down the tab.
➁ Insert the bare wire.
[Remove approx. 5mm (1/4”)
insulation from the speaker
wires.]
➂ Press up the tab and secure
the wire.
CONNECTING THE REAR EFFECT SPEAKERS TO
THIS UNIT
Connect the REAR effect speakers to the REAR SPEAKERS
terminals of this unit.
NOTE: If for some reason, you wish to use an external power amp
for the rear effect channel, connect the REAR OUTPUT jacks to the
INPUT jacks of the external amp and connect the rear effect speaker
pair to the speaker terminals of the external amp.
15
SINGLE
DUALDUAL
SINGLE
AB
Rear Effect
Speaker
R
Rear Effect
Speaker
L
➀
➁
➂
16
CONNECTING THE CENTER SPEAKER(S) TO THIS
UNIT
Connect the CENTER speaker to the CENTER SPEAKERS
terminals. One or two CENTER speakers can be connected to this
unit. For the respective connections, follow the methods figured
below. If, however, you will not be using a CENTER speaker, be sure
to set the Center Mode to “PHNTM” (phantom). (See page 23.)
For connecting one CENTER speaker
For connecting two CENTER speakers
NOTE: If for some reason, you wish to use an external power amp
for the center channel, connect the CENTER OUTPUT jack to the
INPUT jack of the external amp and connect the center speaker to
the speaker terminals of the external amp.
SINGLE
DUALDUAL
SINGLE
AB
SINGLE
DUALDUAL
SINGLE
AB
Center speaker
Center speaker Center speaker
ADDING A SUBWOOFER
You may wish to add a subwoofer to reinforce the bass
frequencies.
This unit provides a line-level subwoofer output, which contains
only the frequencies under 200 Hz from the main and center
channels. Connect the LOW PASS jack to the INPUT jack of the
subwoofer amplifier, and connect the speaker terminals of the
subwoofer amplifier to the subwoofer.
With some subwoofers, including the Yamaha Active Servo
Processing Subwoofer System, the amplifier and subwoofer are in
the same unit.
17
OUTPUT
10dB 0dB
-
Subwoofer system
18
1-3. CONTROLS & ADJUSTMENTS
FRONT PANEL
NATURAL SOUND DIGITAL SOUND FIELD PROCESSOR
/
AMPLIFIER DSP-E580
TAPE
MONITOR
PROGRAM EFFECT
DSP
PRO LOGIC
123456
9
7 8
(General Model)
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
Sidan laddas ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
på andra språk
- italiano: Yamaha 580 Manuale del proprietario
- čeština: Yamaha 580 Návod k obsluze
- español: Yamaha 580 El manual del propietario
- Deutsch: Yamaha 580 Bedienungsanleitung
- polski: Yamaha 580 Instrukcja obsługi
- português: Yamaha 580 Manual do proprietário
- français: Yamaha 580 Le manuel du propriétaire
- Türkçe: Yamaha 580 El kitabı
- English: Yamaha 580 Owner's manual
- dansk: Yamaha 580 Brugervejledning
- русский: Yamaha 580 Инструкция по применению
- suomi: Yamaha 580 Omistajan opas
- Nederlands: Yamaha 580 de handleiding
- română: Yamaha 580 Manualul proprietarului
Relaterade papper
-
Yamaha DSP-A780 Användarmanual
-
-
-
-
-
-
-
-
-