Hilti SB 6-22 Användarmanual

SB 6-22

English 1

Français 14

Español 28

Português 43

Dansk 57

Svenska 71

Norsk 85

Suomi 98

Eesti 112

Latviešu 126

Lietuvių 140

Русский 154

Қазақ 170

ﻋﺮﺑﻲ 186

日本語 201

한국어 214

繁體中文 228

中文 240

1

2

3

4

5

6

7

8

SB 6-22

en Originaloperatinginstructions....................................... 1

fr Moded'emploioriginal........................................... 14

es Manualdeinstruccionesoriginal .................................... 28

pt Manualdeinstruçõesoriginal ...................................... 43

da Originalbrugsanvisning .......................................... 57

sv Originalbruksanvisning........................................... 71

no Originalbruksanvisning .......................................... 85

fi Alkuperäisetohjeet ............................................. 98

et Originaalkasutusjuhend .......................................... 112

lv Oriģinālā lietošanas instrukcija . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126

lt Originalinaudojimoinstrukcija...................................... 140

ru Перевод оригинального руководства по эксплуатации . . . . . . . . . . . . . . . . . . . . 154

kk Түпнұсқа пайдалану бойынша нұсқаулық . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170

ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ .......................................... 186

ja オリジナル取扱説明書 ............................................ 201

ko 오리지널사용설명서............................................. 214

zh 原始操作說明.................................................. 228

cn 原版操作说明译文 ............................................... 240

*2354067* 2354067 English 1

Original operating instructions

1 Information about the operating instructions

1.1 About these operating instructions

• Read these operating instructions before the product is used or operated for the first time. This is a

prerequisite for safe, trouble-free handling and use of the product.

• Observe the safety instructions and warnings in these operating instructions and on the product.

• Always keep the operating instructions with the product and make sure that the product is accompanied

by these operating instructions only, when the product is given to other persons.

1.2 Explanation of symbols

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the

equipment or other property.

1.2.2 Symbols in the operating instructions

The following symbols are used in these operating instructions:

Comply with the operating instructions

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

Hilti Liion battery

Hilti charger

1.2.3 Symbols in illustrations

The following symbols are used in illustrations:

These numbers refer to the illustrations at the beginning of these operating instructions.

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text.

Item reference numbers are used in the overview illustration and refer to the numbers used in

the key in the product overview section.

These characters are intended to specifically draw your attention to certain points when handling

the product.

2 English 2354067 *2354067*

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols can be used on the product:

Direct current (DC)

Direction-of-rotation arrow

The product supports near-field communication (NFC) technology compatible with iOS and

Android platforms.

Li-ion battery

Never strike the battery with an object and never use the battery as a striking tool.

Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any

other way.

1.4 Product information

products are designed for professional users and only trained, authorized personnel are

permitted to operate, service and maintain the products. This personnel must be specifically informed about

the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by

untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Cordless bandsaw SB 6-22

Generation 01

Serial no.

1.5 Declaration of conformity

The manufacturer declares, on his sole responsibility, that the product described here complies with the

applicable legislation and standards. A copy of the declaration of conformity can be found at the end of this

documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

▶Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

Electrical safety

▶Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

*2354067* 2354067 English 3

▶Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

▶When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

▶If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶Use personal protective equipment. Always wear eye protection. Protective equipment such as a

dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will

reduce personal injuries.

▶Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

▶Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

▶Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

▶Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

▶Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

▶Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

▶Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

▶Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with another battery pack.

▶Use power tools only with specifically designated battery packs. Use of any other battery packs may

create a risk of injury and fire.

4 English 2354067 *2354067*

▶When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a fire.

▶Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

▶Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may

exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

▶Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature

above 130° C (265 °F) may cause explosion.

▶Follow all charging instructions and do not charge the battery pack or tool outside the temperature

range specified in the instructions. Charging improperly or at temperatures outside the specified range

may damage the battery and increase the risk of fire.

Service

▶Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

▶Never service damaged battery packs. Service of battery packs should only be performed by the

manufacturer or authorized service providers.

2.2 Safety instructions for band saws

▶Hold power tool by insulated gripping surfaces, when performing an operation where the cutting

accessory may contact hidden wiring. Cutting accessories contacting a "live" wire may make exposed

metal parts of the power tool "live" and could give the operator an electric shock.

2.3 Additional safety instructions

▶Keep your hands away from the cutting area and the bandsaw blade. Keep your second hand on the grip

with the safety switch. When both hands are on the saw they cannot be injured by the saw while it is in

use.

▶Use the product and accessories only when they are in perfect working order.

▶Never tamper with or modify the product or accessories in any way.

▶Switch the product on only after you have brought it to the working position.

▶Do not touch rotating parts – risk of injury!

▶Take care when lifting and/or carrying the product - the bandsaw blade is sharp and can cause cut

injuries or damage to property.

▶Wear eye protection, a hard hat and ear protection while the product is in use.

▶Wear protective gloves when changing the accessory tool. Touching the accessory tool can result in

cuts and burns.

▶Dust produced by grinding, sanding, cutting and drilling can contain dangerous chemicals. Some

examples are: lead or lead-based paints; brick, concrete and other masonry products, natural stone

and other products containing silicates; certain types of wood, such as oak, beech and chemically

treated wood; asbestos or materials that contain asbestos. Determine the exposure of the operator and

bystanders by means of the hazard classification of the materials to be worked. Implement the necessary

measures to restrict exposure to a safe level, for example by the use of a dust collection system or by

the wearing of suitable respiratory protection. The general measures for reducing exposure include:

▶working in an area that is well ventilated,

▶avoidance of prolonged contact with dust,

▶directing dust away from the face and body,

▶wearing protective clothing and washing exposed areas of the skin with water and soap.

▶To avoid injuries, use the bandsaw only with the bandsaw blade cover correctly installed.

▶When ripping always use a fence or straight edge guide. This improves the accuracy of the cut and

reduces the chance of the blade binding.

▶Never hold the workpiece with your hand or other part of the body. Secure the workpiece in a sturdy

holder. It is important to secure the workpiece firmly in order to minimize the risk of body contact, blade

binding, and loss of control.

▶Always hold the product firmly with both hands on the grips provided for the purpose and position your

arms to absorb kickback forces.

▶Keep the grips dry, clean and free from oil and grease.

*2354067* 2354067 English 5

▶Position yourself off to one side of the blade, never bring the blade into line with your body. The saw can

jump backward toward you if kickback occurs!

▶Make sure you have a firm stance, especially for overhead work. A sudden break-through can affect your

balance.

▶When undertaking break-through work, secure the zone on both sides of the workpiece. Pieces of debris

can fall and cause injuries.

▶If the saw blade binds or when you interrupt work for any reason, switch off the saw and hold it motionless

in the material until the saw blade comes to a complete stop. Never attempt to remove the saw from the

workpiece or pull the saw back while the blade is in motion, as otherwise the saw could kick back.

▶When restarting a saw in the workpiece, center the saw blade in the kerf and check that saw teeth are

not in engagement with the workpiece.

▶Use extra caution when sawing into walls or other blind areas. As it enters the material the blade might

encounter a hidden obstruction, resulting in kickback.

▶Take frequent breaks and do physical exercises to improve the blood circulation in your fingers. High

vibration during long periods of work can lead to disorders of the blood vessels and nervous system in

the fingers, hands and wrists.

▶Do not look directly into the light source (LED) of the product and do not aim the beam at other persons’

faces. Risk of dazzling or eye damage.

▶Before starting the cut, check that the bandsaw blade is correctly installed. An incorrectly installed

bandsaw blade can bind and cause a kickback.

▶Risk of injury by falling tools and/or accessories. Before starting work, check that the battery and installed

accessories are secure.

Electrical safety

▶Before beginning work, check the working area for concealed electric cables or gas and water pipes.

External metal parts of the product could give you an electric shock or cause an explosion if you

accidentally damage an electric cable or a gas or water pipe.

▶When cutting through pipes, e.g. when carrying out demolition or installation work, check to ensure that

the pipes no longer contain liquids and empty them if necessary. When cutting through pipes, hold the

product above the level of the pipe you are cutting through. The product is not protected against ingress

of moisture.

Power tool use and care

▶Use only bandsaw blades of the specified size.

▶Do not use dull or damaged bandsaw blades. They cause higher friction, binding or kickback of the

bandsaw blade.

▶Comply with the manufacturer's instructions for handling and storing bandsaw blades.

2.4 Careful handling and use of batteries

▶Comply with the following safety instructions for the safe handling and use of Li-ion batteries.

Failure to comply can lead to skin irritation, severe corrosive injury, chemical burns, fire and/or explosion.

▶Use only batteries that are in perfect working order.

▶Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely

harmful to health!

▶Do not under any circumstances modify or tamper with batteries!

▶Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C

(176 °F).

▶Never use or charge a battery that has suffered an impact or been damaged in any other way. Check

your batteries regularly for signs of damage.

▶Never use recycled or repaired batteries.

▶Never use the battery or a battery-operated power tool as a striking tool.

▶Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This

can lead to explosions.

▶Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects.

This can damage the battery and also cause material damage and personal injury.

▶Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits,

electric shock, burns, fire and explosions.

▶Use only chargers and power tools approved for the specific battery type. Read and follow the relevant

operating instructions.

▶Do not use or store the battery in explosive environments.

6 English 2354067 *2354067*

▶If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible

and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to

cool down. If it is still too hot to touch after an hour, the battery is faulty. Consult Hilti Service or read the

document entitled "Instructions on safety and use for Hilti Li-ion batteries".

Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.

→ page 13

Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning

the QR code at the end of these operating instructions.

3 Description

3.1 Product overview 1

@Grip with safety switch

;Safety switch

=Speed selector switch

%Control switch

&Grip with control switch

(Locking catch for cutting guide

)Cutting guide

+Scaffold hook

§Battery

/Carrier plate

:Screw for carrier plate

∙Bandsaw blade cover

$Screw for bandsaw blade cover

£Guide grooves

|Bandsaw blade guide

¡Bandsaw blade

QPulley

WFastener for pulley

ERubber ring

RBandsaw blade guide channel

TBattery status indicator

ZBattery release button

UClamping lever for bandsaw blade

3.2 Intended use

The product described is a cordless bandsaw. It is designed for cutting metals and plastics.

The product is designed for operation with both hands.

• For this product, use only Hilti Nuron lithium-ion batteries of the B 22 series. For optimum performance,

Hilti recommends the batteries stated in the table at the end of these operating instructions for this

product.

• For these batteries, use only Hilti chargers of the type series stated in the table at the end of these

operating instructions.

3.3 Items supplied

Bandsaw, operating instructions

Other system products approved for use with this product can be found at your local Hilti Store or at:

www.hilti.group

3.4 Status indicators of the Liion battery

Hilti Nuron Li-ion batteries can indicate state of charge, fault messages and the battery's state of health.

*2354067* 2354067 English 7

3.4.1 Indicators for state of charge and fault messages

WARNING

Risk of injury by a falling battery!

▶If the release button is pressed with a battery inserted in the product, subsequently check that the battery

is correctly re-engaged and secure.

Short-press the release button of the battery to get whichever of the following status indications is applicable

at the time.

State of charge and, if applicable, faults are indicated constantly as long as the connected product is

switched on.

Status Meaning

Four (4) LEDs show constantly green State of charge: 100 % to 71 %

Three (3) LEDs show constantly green State of charge: 70 % to 51 %

Two (2) LEDs show constantly green State of charge: 50 % to 26 %

One (1) LED shows constantly green State of charge: 25 % to 10 %

One (1) LED slow-flashes green State of charge: < 10 %

One (1) LED quick-flashes green The Li-ion battery is completely discharged.

Recharge the battery.

If the LED again starts quick-flashing after the bat-

tery has been charged, consult Hilti Service.

One (1) LED quick-flashes yellow The Li-ion battery or the product in which it is in-

serted is overloaded, too hot or too cold, or experi-

encing some other fault.

Bring the product and the battery to the recom-

mended working temperature and do not overload

the product when it is in use.

If the message persists, consult Hilti Service.

One (1) LED shows yellow The Li-ion battery and the product in which it is

inserted are not compatible. Consult Hilti Service.

One (1) LED quick-flashes red The Li-ion battery is locked and cannot be used.

Consult Hilti Service.

3.4.2 Indicators showing the battery's state of health

To check the battery's state of health, press the release button and hold it down for longer than three

seconds. The system does not detect a potential malfunction of the battery due to misuse, for example

battery dropped or pierced, external heat damage, etc.

Status Meaning

All LEDs show in sequence, followed by one (1)

LED showing constantly green. The battery can remain in use.

All LEDs show in sequence, followed by one (1)

LED quick-flashing yellow. The check to ascertain the battery's state of health

did not complete. Repeat the procedure, or consult

Hilti Service.

All LEDs show in sequence, followed by one (1)

LED showing constantly red. If a connected product can still be used, the re-

maining battery capacity is below 50 %.

If a connected product can no longer be used, the

battery has reached the end of its useful life and

has to be replaced. Consult Hilti Service.

4 Technical data

Weight in accordance with EPTA Procedure 01, without battery 6.5 kg

Rated voltage 21.6 V

No-load speed 150 m/min

Max. cutting depth 127 mm

8 English 2354067 *2354067*

Dimensions, product (Length x width x height) 525 mm x 175 mm x 375 mm

Dimensions of bandsaw blade (Length x width x thickness) 1,140 mm x 12.4 mm x 0.5 mm

Ambient temperature for operation −17 ℃ … 60 ℃

Storage temperature −20 ℃ … 70 ℃

4.1 Battery

Battery operating voltage 21.6 V

Weight, battery See the end of these operating

instructions

Ambient temperature for operation −17 ℃ … 60 ℃

Storage temperature −20 ℃ … 40 ℃

Battery charging starting temperature −10 ℃ … 45 ℃

4.2 Noise information and vibration values in accordance with EN 60745

The sound pressure and vibration values given in these instructions were measured in accordance with a

standardized test and can be used to compare one power tool with another. They can also be used for a

preliminary assessment of exposure. The data given represents the main applications of the power tool.

However, if the power tool is used for different applications, with different accessory tools, or is poorly

maintained, the data can vary. This can significantly increase exposure over the total working period. An

accurate estimation of exposure should also take into account the times when the tool is switched off, or

when it is running but not actually being used for a job. This can significantly reduce exposure over the

total working period. Identify additional safety measures to protect the operator from the effects of noise

and/or vibration, for example: Maintaining the power tool and accessory tools, keeping the hands warm,

organization of work patterns.

Noise information

Sound power level (LWA)86 dB(A)

Uncertainty for the sound power level (KWA)3 dB(A)

Sound pressure level (LpA)75 dB(A)

Uncertainty for the sound pressure level (KpA)3 dB(A)

Total vibration

Vibration emission value for cutting in metal (ah,CM) B 2255 0.8 m/s²

B 22255 0.7 m/s²

Uncertainty (K) 1.5 m/s²

5 Preparations at the workplace

WARNING

Risk of injury by inadvertent starting!

▶Before inserting the battery, make sure that the product is switched off.

▶Remove the battery before making any adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

5.1 Charging the battery

1. Before charging the battery, read the operating instructions for the charger.

2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.

3. Use an approved charger to charge the battery. → page 6

*2354067* 2354067 English 9

5.2 Inserting the battery

WARNING

Risk of injury by short circuit or falling battery!

▶Before inserting the battery, make sure that the contacts on the battery and the contacts on the product

are free of foreign matter.

▶Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.

2. Push the battery into the product until it engages with an audible click.

3. Check that the battery is seated securely.

5.3 Removing the battery

1. Press the battery release button.

2. Remove the battery from the product.

5.4 Changing bandsaw blade 2

WARNING

Risk of injury due to the bandsaw blade. The bandsaw blade might be hot and/or have sharp edges; under

certain circumstances it can break.

▶Wear protective gloves and eye protection when working and when changing the bandsaw blade.

▶Use the bandsaw only with the bandsaw blade cover correctly installed.

▶Never set a bandsaw down on a flammable surface while hot from being used.

ATTENTION

Damage to property due to wrong bandsaw blade. Using a wrong bandsaw blade can lead to premature

material fatigue and damage to the bandsaw.

▶Select the correct bandsaw blade for the bandsaw and the material.

▶Select the bandsaw bade with the correct tooth pitch (teeth per inch, tpi) for the material you are going

to cut: higher tpi for hard/thin materials; lower tpi for soft/thick materials.

▶Use only bandsaw blades that are 0.5 mm thick. Thicker bandsaw blades mean more bending strain and

accelerated wear of the saw teeth.

▶Select the bandsaw blade such that at least two saw teeth are in contact with the workpiece.

▶Use only bandsaw blades with the dimensions 1140 mm × 12.5 mm × 0.5 mm.

1. Slacken the screws of both bandsaw blade covers.

2. Remove both bandsaw blade covers.

3. Turn the clamping lever as far as it will go.

▶The bandsaw blade is loosened.

4. Remove the old bandsaw blade from the guide and disposal of the bandsaw blade.

5. Insert the new bandsaw blade into the bandsaw blade guide.

6. Loop the new bandsaw blade over both pulleys.

7. Insert the new bandsaw blade into the bandsaw blade guide channel.

8. Check that the bandsaw blade is correctly seated.

9. Turn the clamping lever as far as it will go.

▶The bandsaw blade is tensioned.

10. Install both bandsaw blade covers.

11. Tighten the screws of both bandsaw blade covers.

5.5 Fall arrest

WARNING

Risk of injury by falling tool and/or accessory!

▶Use only the Hilti tool tether recommended for your product.

▶Prior to each use, always check the attachment point of the tool tether for possible damage.

10 English 2354067 *2354067*

Comply with the national regulations for working at heights.

As drop arrester for this product, use only the Hilti tool tether #2261971.

▶Use the loop to secure the tool tether to the product as shown in the illustration. Check that it holds

securely.

▶Secure the carabiner to a load-bearing structure. Check that the carabiner holds securely.

Comply with the operating instructions of the Hilti tool tether.

6 Operation

Observe the safety instructions and warnings in this documentation and on the product.

6.1 Adjusting cutting guide

1. Press and hold down the locking catch of the cutting guide.

2. Move the cutting guide to the desired height.

3. Release the locking catch of the cutting guide.

6.2 Sawing 3,4

WARNING

Risk of injury by kickback of the bandsaw.

▶Secure the workpiece in a bench vise, for example, before you start sawing.

▶Bring the bandsaw and the workpiece into alignment.

WARNING

Risk of injury by saw run-on.

▶Do not lift the product away from the workpiece until it has stopped completely.

▶Wait until the product stops completely before you lay it down.

WARNING

Risk of injury due to the bandsaw blade. The bandsaw blade might be hot and/or have sharp edges; under

certain circumstances it can break.

▶Wear protective gloves and eye protection when working and when changing the bandsaw blade.

▶Use the bandsaw only with the bandsaw blade cover correctly installed.

▶Never set a bandsaw down on a flammable surface while hot from being used.

*2354067* 2354067 English 11

ATTENTION

Damage to property due to wrong bandsaw blade. Using a wrong bandsaw blade can lead to premature

material fatigue and damage to the bandsaw.

▶Select the correct bandsaw blade for the bandsaw and the material.

▶Select the bandsaw bade with the correct tooth pitch (teeth per inch, tpi) for the material you are going

to cut: higher tpi for hard/thin materials; lower tpi for soft/thick materials.

▶Use only bandsaw blades that are 0.5 mm thick. Thicker bandsaw blades mean more bending strain and

accelerated wear of the saw teeth.

▶Select the bandsaw blade such that at least two saw teeth are in contact with the workpiece.

▶Use only bandsaw blades with the dimensions 1140 mm × 12.5 mm × 0.5 mm.

Check the rubber ring for damage at regular intervals.

After every cutting operation, remove dust and chips from the bandsaw blade covers and the cutting guide

to prolong the useful life of the bandsaw.

To start the bandsaw, you must: First press the control switch and then press the safety switch and

hold both switches down at the same time.

The weight of the bandsaw is sufficient to make the cut. Do not apply additional pressure to the

bandsaw.

1. Replace the rubber ring when necessary. → page 12

2. Change the bandsaw blade when necessary. → page 9

3. Press and hold down the control switch.

4. Press and hold down the safety switch.

5. Position the bandsaw on the workpiece in such a way that as many saw teeth as possible act on the

workpiece.

6. Carry out the sawing work.

Guide the bandsaw in such a way that at least three saw teeth remain in the cut at all times if

possible.

7. Release the control switch.

7 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶Always remove the battery before carrying out care and maintenance tasks!

Care of the product

• Carefully remove stubborn dirt.

• Carefully clean the air vents, if present, with a dry, soft brush.

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

• Use a dry, clean cloth to clean the contacts of the product.

Care of the Liion batteries

• Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.

• Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of

moisture (e.g. by being dipped in water or left in the rain).

If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable

container and consult Hilti Service.

• Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily

on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents

containing silicone as these can attack the plastic parts.

Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts.

12 English 2354067 *2354067*

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product

repaired by Hilti Service.

• After cleaning and maintenance, install all guards and protective devices and check that they are in full

working order.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with your product can be found at your

Hilti Store or online at: www.hilti.group

7.1 Replacing bandsaw blade cover 5

Replace the bandsaw blade cover as soon as you find signs of damage.

1. Slacken the screws of the bandsaw blade cover.

2. Remove the damaged bandsaw blade cover and dispose of it correctly.

3. Position the new bandsaw blade cover on the bandsaw.

4. Tighten the screws of the bandsaw blade cover to 2 to 3 Nm.

7.2 Changing rubber ring 6

Replace the rubber ring as soon as you find signs of damage.

1. Remove the bandsaw blade → page 9.

2. Remove the rubber ring.

3. Check that the guide grooves are free of foreign matter and clean them if necessary.

4. Stretch the new rubber ring over the pulley for the bandsaw blade.

5. Ease the rubber ring into position on the pulley until it is fully flush with the guide grooves.

6. Re-install the bandsaw blade. → page 9.

7.3 Replacing bandsaw blade guide 7

Replace the bandsaw blade guide as soon as you find signs of damage, for example if the bandsaw

blade has notched into the guide.

1. Remove the bandsaw blade → page 9.

2. Slacken both screws of the bandsaw blade guide.

3. Remove the damaged bandsaw blade guide from the bandsaw and dispose of the bandsaw blade guide

correctly.

4. Insert the new bandsaw blade guide into the bandsaw.

5. Tighten the two screws of the bandsaw blade guide to 2 to 3 Nm.

6. Re-install the bandsaw blade. → page 9.

7.4 Replacing carrier plate 8

Replace the carrier plate as soon as the bandsaw blade drags or binds.

1. Remove the bandsaw blade → page 9.

2. Slacken the screw of the carrier plate.

3. Remove the damaged carrier plate from the bandsaw and dispose of the carrier plate correctly.

*2354067* 2354067 English 13

4. Insert the new carrier plate into the bandsaw.

5. Tighten the screw of the carrier plate to 2 to 3 Nm.

6. Re-install the bandsaw blade. → page 9.

8 Transport and storage of cordless tools and batteries

Transport

CAUTION

Accidental starting during transport !

▶Always transport your products with the batteries removed!

▶Remove the battery/batteries.

▶Never transport batteries loose and unprotected. During transport, batteries should be protected from

excessive shock and vibration and isolated from any conductive materials or other batteries that may

come in contact with the terminals and cause a short circuit. Comply with the locally applicable

regulations for transporting batteries.

▶Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged

batteries.

▶Prior to each use and before and after prolonged transport, check the product and the batteries for

damage.

Storage

WARNING

Accidental damage caused by defective or leaking batteries !

▶Always store your products with the batteries removed!

▶Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in

the technical data.

▶Do not store batteries on the charger. Always remove the battery from the charger when the charging

operation has completed.

▶Never leave batteries in direct sunlight, on sources of heat, or behind glass.

▶Store the product and batteries where they cannot be accessed by children or unauthorized persons.

▶Prior to each use and before and after prolonged storage, check the product and the batteries for

damage.

9 Troubleshooting

If a problem occurs, always observe the status indicator of the battery. See the section headed Status

indicators of the Liion battery.

If the trouble you are experiencing is not listed in this table or you are unable to rectify the problem by

yourself, contact Hilti Service.

Trouble or fault Possible cause Action to be taken

Product does not develop full

power. The control switch is not fully

pressed.

▶Press the control switch fully.

The product can’t be

switched on. Switch-on interlock not activated. ▶Activate the switch-on interlock.

Product does not start. Bandsaw blade jams ▶Check whether the bandsaw

blade is fitted correctly and/or

damaged.

LEDs of the battery show

nothing Battery defective ▶Contact Hilti Service.

14 Français 2354067 *2354067*

10 Disposal

WARNING

Risk of injury due to incorrect disposal! Health hazards due to escaping gases or liquids.

▶DO NOT send batteries through the mail!

▶Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.

▶Dispose of your battery out of the reach of children.

▶Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public

health and safety resources for disposal instructions.

Most of the materials from which Hilti products are manufactured can be recycled. The materials must be

correctly separated before they can be recycled. In many countries, your old tools, machines or appliances

can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information.

▶Do not dispose of power tools, electronic equipment or batteries as household waste!

11 Manufacturer’s warranty

▶Please contact your local Hilti representative if you have questions about the warranty conditions.

12 Further information

For more information on operation, technology, environment and recycling, follow this link:

qr.hilti.com/manual/?id=2354065&id=2354067

This link is also to be found at the end of the documentation, in the form of a QR code.

Mode d'emploi original

1 Indications relatives au mode d'emploi

1.1 À propos de ce mode d'emploi

• Avant de mettre l'appareil en marche, lire impérativement ce mode d'emploi. C'est la condition

préalablement requise pour assurer la sécurité du travail et un maniement sans perturbations.

• Bien respecter les consignes de sécurité et les avertissements du présent mode d'emploi ainsi que celles

figurant sur le produit.

• Toujours conserver le mode d'emploi à proximité du produit et uniquement transmettre le produit à des

tiers accompagné de ce mode d'emploi.

1.2 Explication des symboles

1.2.1 Avertissements

Les avertissements attirent l'attention sur des dangers liés à l'utilisation du produit. Les termes de

signalisation suivants sont utilisés :

DANGER

DANGER !

▶Pour un danger imminent qui peut entraîner de graves blessures corporelles ou la mort.

AVERTISSEMENT

AVERTISSEMENT !

▶Pour un danger potentiel qui peut entraîner de graves blessures corporelles ou la mort.

Sidan laddas ...

Hilti SB 6-22 Användarmanual

Hilti SB 6-22 Användarmanual

på andra språk