Sony Stereo Amplifier TA-FA1200ES Användarmanual

2-688-078-11(2)

Integrated

Stereo Amplifier

Operating Instructions ________________________

Manual de instrucciones ______________________

Bruksanvisning _____________________________

___________________________

TA-FA1200ES

ES

GB

SE

PL

2

GB

To reduce the risk of fire or electric

shock, do not expose this apparatus to

rain or moisture.

To prevent fire, do not cover the ventilation of the

apparatus with news papers, table-cloths, curtains,

etc. And don’t place lighted candles on the

apparatus.

To prevent fire or shock hazard, do not place objects

filled with liquids, such as vases, on the apparatus.

Do not install the appliance in a confined space, such

as a bookcase or built-in cabinet.

Install this system so that the power cord can be

unplugged from the wall socket immediately in the

event of trouble.

Don’t throw away the battery with

general house waste, dispose of it

correctly as chemical waste.

NOTICE FOR THE CUSTOMERS IN THE

UNITED KINGDOM

A moulded plug complying with BS1363 is fitted to

this equipment for your safety and convenience.

Should the fuse in the plug supplied need to be

replaced, a fuse of the same rating as the supplied

one and approved by ASTA or BSI to BS1362, (i.e.,

marked with or mark) must be used.

If the plug supplied with this equipment has a

detachable fuse cover, be sure to attach the fuse

cover after you change the fuse. Never use the plug

without the fuse cover.

If you should lose the fuse cover, please contact your

nearest Sony service station.

For customers in Europe

Disposal of Old Electrical & Electronic

Equipment (Applicable in the European

Union and other European countries

with separate collection systems)

WARNING

This symbol on the product or on its

packaging indicates that this product

shall not be treated as household waste.

Instead it shall be handed over to the

applicable collection point for the

recycling of electrical and electronic

equipment. By ensuring this product is

disposed of correctly, you will help

prevent potential negative

consequences for the environment and

human health, which could otherwise

be caused by inappropriate waste

handling of this product. The recycling

of materials will help to conserve

natural resources. For more detailed

information about recycling of this

product, please contact your local

Civic Office, your household waste

disposal service or the shop where you

purchased the product.

3

GB

About this manual

• The instructions in this manual are for model TA-

FA1200ES. Check your model number by looking

at the lower right corner of the front panel.

• The instructions in this manual describe the

controls on the supplied remote. You can also use

the controls on the amplifier if they have the same

or similar names as those on the remote.

This amplifier incorporates Dolby* Digital and

DTS**.

* Manufactured under license from Dolby

Laboratories.

“Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

** “DTS” and “DTS 2.0” are trademarks of Digital

Theater Systems, Inc.

Table of contents

Getting Started

Unpacking ....................................................4

Connecting speakers .....................................4

Using a bi-amplifier connection ...................6

Connecting components with analog audio

input/output jacks ....................................7

Connecting components with digital audio

input/output jacks ....................................8

Connecting the AC power cord

(mains lead) .............................................9

Inserting batteries into the remote ................9

Location of Parts and

Operation

Front panel ..................................................10

Rear panel ...................................................11

Remote commander ....................................12

Configuration

Calibrating the appropriate settings

automatically

(AUTO CALIBRATION) ......................13

Settings for the amplifier ............................16

Clearing the amplifier’s memory ................18

Additional Information

Precautions .................................................19

Troubleshooting ..........................................20

Specifications .............................................22

Index ...........................................................23

GB

4

GB

Unpacking

Check that you received the following items:

• Operating Instructions (this manual)

• Optimizer microphone ECM-AC1 (1)

• AC power cord (mains lead) (1)

• Remote commander RM-AAU010 (1)

• R6 (size-AA) batteries (2)

If any item is missing, please consult your

nearest Sony dealer.

Audio connecting cords, digital connecting

cords, speaker cords are not supplied with this

amplifier. Please purchase them separately.

Notes on connections

• Turn off the power to all components before

making any connections.

• Do not connect the AC power cord (mains

lead) until all of the connections are

completed.

• Be sure to insert all plugs firmly to avoid

hum and noise.

Connecting speakers

Connect your speakers to the amplifier.

Use a speaker cord (not supplied) to connect to

the speaker terminals.

Speaker cord (not supplied)

Notes on speaker connections

Connect the left speaker to the SPEAKERS L

terminal and the right speaker to the

SPEAKERS R terminal.

Be sure to connect the speaker cords between

the speakers and the amplifier with the same

polarities (plus (+) to plus (+), minus (–) to

minus (–)).

By paying attention to the color or mark of the

speaker cord to be connected to the plus (+) or

minus (–) connector, you can always be sure of

connecting the cord correctly without

mistaking plus or minus.

Getting Started

5

GB

Getting Started

Setting the speaker impedance

• Be sure to turn the power off before

adjusting the IMPEDANCE SELECTOR.

• When you connect all speakers with a

nominal impedance of 8 ohms, set the

IMPEDANCE SELECTOR to “8Ω .” When

connecting other types of speakers, set it to

“4Ω .”

• When you connect speakers to both the

SPEAKERS A and B terminals, connect the

speakers with a nominal impedance of 8

ohms or higher.

– When you connect speakers with

impedance of 16 ohms or higher in both

“A” and “B” configuration:

Set IMPEDANCE SELECTOR to “8Ω .”

– For other types of speakers in other

configurations:

Set IMPEDANCE SELECTOR to “4Ω .”

• If you are not sure of the impedances of the

speakers, refer to the operating instructions

supplied with your speakers. (This

information is often on the back of the

speaker.)

* If you have an additional speaker system, connect

them to the SPEAKERS B terminals. You can

select the speaker system you want to use with the

SPEAKERS (OFF/A/B/A+B) on the front panel

(page 11).

SPEAKERS B terminals*

IMPEDANCE SELECTOR

Speaker A

(L)

Speaker A

(R)

6

GB

Using a bi-amplifier

connection

You can make a bi-amplifier connection by

connecting both the SPEAKERS A terminals

and SPEAKERS B terminals simultaneously.

When using a bi-amplifier connection, set

SPEAKERS (OFF/A/B/A+B) to A+B

(page 11).

To connect speakers

Connect the terminals on the Lo (or Hi) side of

the speakers to the SPEAKERS A terminals,

and connect the terminals on the Hi (or Lo)

side of the speakers to the SPEAKERS B

terminals. Make sure that metal fittings of Hi/

Lo attached to the speakers have been removed

from the speakers. Not doing so may cause a

malfunction of the amplifier.

Note

When you use the auto calibration function, make

the bi-amplifier settings before you perform auto

calibration.

Speaker

(L)

Speaker

(R)

Hi

Lo

Hi

Lo

7

GB

Getting Started

Connecting components with analog audio input/

output jacks

You can connect a component with analog

audio jacks, such as a Super Audio CD player

or CD player, etc. to this amplifier.

Use an audio cord (not supplied) to connect a

component to the analog audio jacks.

Connect the white plug to the L jack and the

red plug to the R jack.

Audio cord (not supplied)

Note

If your turntable has a ground (earth) wire, connect

it to the (U) SIGNAL GND terminal.

Tur ntabl e

Super Audio CD

player,

CD player,

VCR

Tape deck

8

GB

Connecting components with digital audio input/output

jacks

You can connect a component with coaxial

digital output jacks to this amplifier.

Use a coaxial digital cord (not supplied) to

connect a component to the coaxial jacks

(DIGITAL 1 to 3).

Coaxial digital cord (not supplied)

You can connect a component with optical

digital output jacks to this amplifier.

Use an optical digital cord (not supplied) to

connect a component to the optical jacks

(DIGITAL 4).

When connecting optical digital cords, insert

the plugs straight in until they click into place.

Optical digital cord (not supplied)

Note

When DIGITAL 1, 2, or 3 is selected, the selected

input signal is output from the DIGITAL 4 OUT

jack. When DIGITAL 4 or analog input is selected,

no signal is output from the DIGITAL 4 OUT jack.

Tip

All the digital audio jacks are compatible with 32

kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling

frequencies.

Connecting to the COAXIAL jack Connecting to the OPTICAL jack

MD deck,

DAT deck,

Satellite tuner

(for the IN jack only)

Super Audio CD player,

CD player,

DVD player,

DVD recorder

9

GB

Getting Started

Connecting the AC power

cord (mains lead)

Connect the supplied AC power cord (mains

lead) to the AC IN terminal on the amplifier,

then connect the AC power cord (mains lead)

to a wall outlet.

You can connect the AC power cord (mains

lead) of your component to the amplifier’s AC

OUTLET(s).

* The configuration, shape, and number of AC

outlets will vary according to the area.

** A several space is left between the plug and the

rear panel even when the power cord (mains

lead) is inserted firmly. The cord is supposed be

connected this way. This is not a malfunction.

Notes

• The AC OUTLET(s) on the rear of the amplifier is

a switched outlet, which supplies power to the

connected component only while the amplifier is

turned on.

• Make sure that the total power consumption of the

component(s) connected to the amplifier’s AC

OUTLET(s) does not exceed the wattage stated on

the rear panel. Do not connect high-wattage

electrical home appliances such as electric irons,

fans, or TVs to this outlet. This may cause a

malfunction.

Inserting batteries into

the remote

Insert two R6 (size-AA) batteries in the RM-

AAU010 remote commander.

Observe the correct polarity when installing

batteries.

Notes

• Do not leave the remote in an extremely hot or

humid place.

• Do not use a new battery with old ones.

• Do not mix manganese batteries and other kinds of

batteries.

• Do not expose the remote sensor to direct sunlight

or lighting apparatuses. Doing so may cause a

malfunction.

• If you do not intend to use the remote for an

extended period of time, remove the batteries to

avoid possible damage from battery leakage and

corrosion.

Tip

When the remote no longer operates the amplifier,

replace all the batteries with new ones.

AC OUTLET*AC IN terminal

To the wall outlet

AC power cord

(mains lead)

(supplied)

**

RM-AAU010

10

GB

Front panel

Location of Parts and Operation

Name Function

A POWER Press to turn the

amplifier on or off.

B AUTO CAL MIC

jack

Connects to the

supplied optimizer

microphone for the

Auto Calibration

function (page 13).

C TONE

BASS/TREBLE

Turn to adjust the

BASS and TREBLE

levels.

The level can be

adjusted from –10 dB

to +10 dB.

D Remote sensor Receives signals from

the remote.

E Display The current status of

the selected component

or a list of selectable

items appears here.

F DIRECT Press to bypass the

TONE function to

listen to better quality

sound.

Note

When you play back a DTS

96/24 format disc, set the

DIRECT function to ON.

If the DIRECT function is set

to OFF, the DTS signal is

played back at 48 kHz.

G MUTING Press to activate the

muting function.

H PHONES jack Connects to

headphones.

Note

When you connect

headphones, the DTS 96/24

signal is played back at DTS

48 kHz.

Name Function

11

GB

Location of Parts and Operation

Rear panel

I SPEAKERS

(OFF/A/B/A+B)

Turn to select OFF, A,

B, A+B of the speakers.

J INPUT

SELECTOR

Turn to select the input

source to play back.

Name Function

K VOLUME Turn to adjust the

volume level of

speakers. The level can

be adjusted from –∞ dB

to +23 dB.

Name Function

A AUDIO INPUT/OUTPUT section

AUDIO IN/

OUT jacks

Connects to a Super

Audio CD player,

tape deck, MD deck

or DAT player, etc

(page 7).

B DIGITAL INPUT/OUTPUT section

COAXIAL IN

jacks

Connects to a DVD

player, Super Audio

CD player, etc. The

COAXIAL jacks

provide a better

quality sound (page

8).

OPTICAL IN/

OUT jack

L

R

C SPEAKERS section

Connects to speakers

(page 4).

D IMPEDANCE SELECTOR

Set the appropriate speaker impedance for the

speakers you are using (page 5).

12

GB

Remote commander

RM-AAU010

Name Function

A ?/1

(on/standby)

Press to turn the amplifier on or

off.

B U/u/I/i

ENTER

After pressing MENU (9),

press U/u, I or i to select the

settings. Then press ENTER to

enter the selection (page 16).

C Input

buttons

Press one of the buttons to

select the component you want

to use. When you press any of

the input buttons, the amplifier

turns on.

D BALANCE

L/R

Press to adjust the balance

between left and right speakers.

Both the left and the right

balance can be adjusted from 0

dB to +20 dB. The initial setting

is 0 dB (center).

E BASS/

TREBLE +/–

Press to adjust the BASS and

TREBLE levels. The level can

be adjusted from –10 dB to +10

dB.

F DIMMER Press to adjust brightness of the

display.

G VOLUME +/– Press to adjust the volume level

of speakers.

The level can be adjusted from

–∞ dB to +23 dB.

H SLEEP Press to activate the Sleep

Timer function and the duration

which the amplifier turns off

automatically.

The Sleep Timer can be set to

30, 60, 90, or 120 minutes.

I MENU Press to display the menu for

the amplifier (page 16).

J DIRECT Press to bypass the TONE

function to listen to better

quality sound.

Note

When you play back a DTS 96/24

format disc, set the DIRECT

function to ON.

If the DIRECT function is set to

OFF, the DTS signal is played back

at 48 kHz.

K MUTING Press to activate the muting

function.

13

GB

Configuration

Calibrating the

appropriate settings

automatically

(AUTO

CALIBRATION)

The auto calibration function allows you to

measure the following:

• Whether or not speakers are connected

• Polarity of speakers

• Distance of each speaker from your listening

position

• Speaker angle

• Speaker level

• Frequency characteristics

After saving the measurement result, you can

confirm the speaker level by pressing

BALANCE L/R (page 12). The other

measurement results are not displayed, but are

set to appropriate settings automatically.

Before you perform the auto calibration, set up

and connect the speakers (page 4).

• The AUTO CAL MIC jack is used for the

supplied optimizer microphone only. Do not

connect other microphones to this jack.

Doing so may damage the amplifier and the

microphone.

• During the calibration, the sound that comes

out of the speakers is very loud. The volume

of the sound cannot be adjusted. Pay

attention to the presence of children or to the

effect on your neighborhood.

• Perform the auto calibration in a quiet

environment to avoid the effect of noise and

get a more accurate measurement.

• If there are any obstacles in the path between

the optimizer microphone and the speakers,

the calibration cannot be performed

correctly. Remove any obstacles from the

measurement area to avoid measurement

error.

Notes

• The auto calibration function does not work when

headphones are connected to the amplifier.

• Cancel MUTING if it is set to on.

1 Connect the supplied optimizer

microphone to the AUTO CAL

MIC jack on the front panel.

2 Set up the optimizer

microphone.

Place the optimizer microphone at your

listening position. Use a stool or tripod so

that the optimizer microphone remains at

the same height as your ears. Orient the L

end of the optimizer microphone toward

the front left speaker and the R end of the

optimizer microphone toward the front

right speaker.

1 Turn on the amplifier.

2 Press MENU.

Configuration

Before you perform auto

calibration

Performing auto calibration

Optimizer microphone

(supplied)

continued

14

GB

3 Press u to display “<2-Auto

Calibration>,” then press

ENTER to enter the menu.

4 Press u to display “CAL TYPE,”

then press ENTER to enter the

parameter.

5 Press U/u to select the

parameter, then press ENTER

to enter the selection.

6 Press U to display “AUTO CAL

START?,” then press ENTER to

start the measurement.

Measurement starts in five seconds. A

countdown appears on the display.

While the time is counting down, stand

away from the measurement area to

avoid measurement error.

7 Measurement starts.

The measurement process will take

approximately 10 seconds. Wait until the

measurement process completes.

Tip

When special speakers, such as dipole speakers, are

used, the measurements may not be performed

correctly or auto calibration cannot be performed.

To cancel auto calibration

Auto calibration is cancelled when you change

the volume, change the input source, change

the speaker selection, press MUTING, or

connect headphones.

1 Confirm the measurement

result.

When the measurement ends, a beep

sounds and the measurement result

appears on the display.

2 Press U/u repeatedly to select

the item, then press ENTER.

When error codes appear

Try the remedies and re-perform the auto

calibration.

Calibration

type

Explanation

ENGINEER Sets the frequency

characteristics to a set that

matches that of the Sony

listening room standard.

FULL FLAT Makes the measurement of

frequency from each

speaker flat.

Confirming/saving the

measurement results

Measurement

result

Display Explanation

When the

measurement

process

completes

properly

COMPLETE

Proceed to step

2.

When the

measurement

process fails

ERROR

CODE XX

See “When

error codes

appear” (page

14).

Item Explanation

RETRY Re-performs the auto

calibration.

SAVE EXIT Saves the measurement

results and exits the setting

process.

WRN CHECK Displays a warning

concerning the

measurement results. See

“When you select “WRN

CHECK”” (page 15).

EXIT Exits the setting process

without saving the

measurement results.

Error code Cause and remedies

CODE 31 SPEAKERS (OFF/A/B/A+B) is

set to OFF. Select A or B and re-

perform the auto calibration.

When using a bi-amplifier

connection, set SPEAKERS

(OFF/A/B/A+B) to A+B.

15

GB

Configuration

•CODE 31

1

Turn SPEAKERS (OFF/A/B/A+B) to select

A or B, then follow the instructions given

in step 2 of “Performing auto calibration.”

When using a bi-amplifier connection, set

SPEAKERS (OFF/A/B/A+B) to A+B.

•CODE 32, 33, 34

1

Remedy the error.

2 Press ENTER.

“RETRY?” appears.

3

Press

U

/

u

to select “YES,” then press ENTER.

The auto calibration is restarted from step 7 of

“Performing auto calibration.”

When you select “WRN CHECK”

If a warning on the measurement result is

present, detailed information is displayed.

Press ENTER to return to step 1 of

“Confirming/saving the

measurement results.”

The initial setting is underlined.

x AUTO CAL START?

(Starts auto calibration)

• MEASUREMENT COUNTDOWN

A time countdown appears on the display

from five seconds to one second.

• MEASURING TONE

Appears while TONE is being measured.

• MEASURING T.S.P.

Appears while TSP* is being measured.

• COMPLETE

Appears when the measurement process

completes successfully. For details on each

message, see “Confirming/saving the

measurement results” (page 14).

• WARNING CODE [ :4x]

Appears if a warning on the measurement

result is present. For details on each

message, see “Confirming/saving the

measurement results” (page 14).

• NO WARNING

There is no warning information.

• ERROR CODE [ :3x]

Appears when the measurement fails. For

details on each message, see “Confirming/

saving the measurement results” (page 14).

CODE 32 None of the speakers were

detected. Make sure that the

optimizer microphone is

connected properly and re-

perform the auto calibration.

If the optimizer microphone is

connected properly but the error

code appears, the optimizer

microphone cable may be damaged

or improperly connected.

CODE 33 None of the speakers are

connected.

CODE 34

Speakers are not placed in the

proper position. Speakers or an

optimizer microphone on the right

or left may be placed wrongly.

Check the speaker position.

Warning code Explanation

WARNING 40

Try to perform the auto calibration

in a quiet environment.

The auto calibration has

completed. However, the noise

level is high. You may be able to

perform the auto calibration

properly if you try it again, even

though the measurement cannot

be performed in all environments.

Error code Cause and remedies

WARNING 41 Try to perform the auto

calibration when the environment

is quiet enough to allow proper

measurement.

The sound input from the

optimizer microphone is outside

the acceptable range. It is louder

than the loudest sound that can be

measured.

WARNING 42 Try to perform the auto

calibration when the environment

is quiet enough to allow proper

measurement.

The volume of the amplifier is out

of the acceptable range.

NO WARNING There is no warning information.

Auto Calibration menu

parameters

Warning code Explanation

continued

16

GB

•RETRY?

Appears to ask you to re-measure or exit

without re-measuring when the

measurement fails.

• CANCEL

Appears when you cancel auto calibration

during the measurement.

* TSP (Time Stretched Pulse)

A TSP signal is a highly precise measuring signal

that utilizes impulse energy, measuring a wide

band, from low to high, in a short period.

The amount of energy used to measure signals is

important to ensure measurement accuracy in a

normal indoor environment. Using TSP signals

makes it possible to measure signals effectively.

x CAL TYPE

(Parameter type)

• ENGINEER

Sets the frequency to one that matches that

of the Sony listening room standard.

•FULL FLAT

Makes the measurement of frequency from

each speaker flat.

x EQ CURVE EFFECT

(Activates/deactivates the EQ

curve measurement)

•OFF

Deactivates the EQ curve measurement.

•ON

Activates the EQ curve measurement.

After the measurement is completed, this

setting is set to ON automatically.

Notes

• DTS 96/24 signals are played back as 48 kHz

signals when EQ CURVE EFFECT is set to “ON.”

When you play back DTS 96/24 signals, set this

item to “OFF” and set the DIRECT function to

“ON” (page 10, 12).

• You cannot select this setting before saving the

measurement results (factory setting).

Settings for the amplifier

By using the System Settings menus, you can

make various adjustments to customize the

amplifier.

1 Press MENU.

2 Press U to display “<1-System

Settings>,” then press ENTER

to enter the menu.

3 Press U/u repeatedly to display

the parameter you want to

adjust.

4 Press ENTER to enter the

parameter.

5 Press U/u repeatedly to select

the setting you want to adjust.

6 Press ENTER to enter.

7 Repeat steps 3 to 6 when you

want to make other settings.

To return to the menu one level

up

Press I.

To exit the menu

Press MENU.

Note

Some parameters and settings may appear dimmed

on the display. This means that they are either

unavailable or fixed and unchangeable.

17

GB

Configuration

The initial setting is underlined.

x DEC. PRIORITY

(Digital audio input decoding

priority)

Lets you specify the input mode for the digital

signal input to the DIGITAL IN jacks.

•AUTO

Automatically switches the input mode

between DTS, Dolby Digital, or PCM.

•PCM

PCM signals are given priority (to prevent

interruption when playback starts).

Note

When set to “AUTO” and the sound from the digital

audio jacks (for a CD, etc.) is interrupted when

playback starts, set to “PCM.”

x DUAL MONO

(Bilingual audio selection)

For a bilingual broadcast, you can select the

language you want to listen to. This feature

only functions for Dolby Digital sources.

• MAIN/SUB

Sound of the main language will be output

through the left speaker, and sound of the

sub language will be output through the right

speaker simultaneously.

•MAIN

Sound of the main language will be output.

•SUB

Sound of the sub language will be output.

• MAIN+SUB

Mixed sound of both the main and sub

languages will be output.

x D.RANGE COMP.

(Dynamic range compressor)

Lets you compress the dynamic range of the

soundtrack. This may be useful when you want

to watch movies at low volumes late at night.

Dynamic range compression is possible with

Dolby Digital sources only.

•OFF

The dynamic range is not compressed.

•STD

The dynamic range is compressed as

intended by the recording engineer.

•MAX

The dynamic range is compressed

dramatically.

Tip

Dynamic range compressor lets you compress the

dynamic range of the soundtrack based on the

dynamic range information included in the Dolby

Digital signal.

“STD” is the standard setting, but it only enacts light

compression. Therefore, we recommend using the

“MAX” setting. This greatly compresses the

dynamic range and lets you view movies late at night

at low volumes. Unlike analog limiters, the levels are

predetermined and provide a very natural

compression.

x DC PHASE L.

(DC Phase Linearizer)

Lets you approximate the low frequency phase

characteristics to a traditional analog

amplifier.

•OFF

Phase correction is not performed.

• LOW-A, STD-A, HIGH-A, LOW-B, STD-

B, HIGH-B

The bandwidth range of the phase correction

increases in the order of “LOW,” “STD,”

“HIGH.”

“B” parameter phase correction provides

more enhanced bass characteristics.

System Settings menu

parameters

18

GB

Clearing the amplifier’s

memory

1

Press POWER to turn off the

amplifier.

2 Hold down POWER while

pressing DIRECT and MUTING

to turn on the amplifier.

After “MEMORY CLEARING...”

appears on the display for a while,

“MEMORY CLEARED!” appears.

The following items are reset to their

initial settings.

• All settings in the System Settings and

Auto Calibration menus.

1,2 2

19

GB

Additional Information

Precautions

On safety

Should any solid object or liquid fall into the

cabinet, unplug the amplifier and have it

checked by qualified personnel before

operating it any further.

On power sources

• Before operating the amplifier, check that

the operating voltage is identical with your

local power supply.

The operating voltage is indicated on the

nameplate on the back of the amplifier.

• The unit is not disconnected from the AC

power source (mains) as long as it is

connected to the wall outlet, even if the unit

itself has been turned off.

• If you are not going to use the amplifier for

a long time, be sure to disconnect the

amplifier from the wall outlet. To disconnect

the AC power cord (mains lead), grasp the

plug itself; never pull the cord.

• The AC power cord (mains lead) must be

changed only at a qualified service shop.

On heat buildup

Although the amplifier heats up during

operation, this is not a malfunction. If you

continuously use this amplifier at a large

volume, the cabinet temperature of the top,

side and bottom rises considerably. To avoid

burning yourself, do not touch the cabinet.

On placement

• Place the amplifier in a location with

adequate ventilation to prevent heat buildup

and prolong the life of the amplifier.

• Do not place the amplifier near heat sources,

or in a place subject to direct sunlight,

excessive dust, or mechanical shock.

• Do not place anything on top of the cabinet

that might block the ventilation holes and

cause malfunctions.

• Do not place the amplifier near equipment

such as a television, VCR, or tape deck. (If

the amplifier is being used in combination

with a television, VCR, or tape deck, and is

placed too close to that equipment, noise

may result, and picture quality may suffer.

This is especially likely when using an

indoor antenna (aerial). Therefore, we

recommend using an outdoor antenna

(aerial).)

On operation

Before connecting other components, be sure

to turn off and unplug the amplifier.

On cleaning

Clean the cabinet, panel, and controls with a

soft cloth slightly moistened with a mild

detergent solution. Do not use any type of

abrasive pad, scouring powder, or solvent,

such as alcohol or benzine.

If you have any questions or problems

concerning your amplifier, please consult your

nearest Sony dealer.

Additional Information

20

GB

Troubleshooting

If you experience any of the following

difficulties while using the amplifier, use this

troubleshooting guide to help you remedy the

problem. Should any problem persist, consult

your nearest Sony dealer.

Audio

There is no sound, no matter which

component is selected, or only a very

low-level sound is heard.

• Check that the speakers and components

are connected securely.

• Check that all speaker cords are connected

correctly.

• Check that both the amplifier and all

components are turned on.

• Check that VOLUME control is not set at

–∞ dB.

• Check that SPEAKERS (OFF/A/B/A+B)

is not set to “OFF” (page 11).

• Press MUTING to cancel the muting

function.

• Check that you have selected the correct

component with INPUT SELECTOR.

• Check that headphones are not connected.

• The protective device on the amplifier has

been activated. Turn off the amplifier,

eliminate the short-circuit problem, and

turn on the power again.

There is no sound from a specific

component.

• Check that the component is connected

correctly to the audio input jacks for that

component.

• Check that the cord(s) used for the

connection is (are) fully inserted into the

jacks on both the amplifier and the

component.

There is no sound from one of the

speakers.

• Connect a pair of headphones to the

PHONES jack to verify that sound is

output from the headphones. If only one

channel is output from the headphones, the

component may not be connected to the

amplifier correctly. Check that all the

cords are fully inserted into the jacks on

both the amplifier and the component. If

both channels are output from the

headphones, the speaker may not be

connected to the amplifier correctly.

Check the connection of the speaker which

is not outputting any sound.

• Make sure you have connected both the L

or R jack to an analog component and not

just to either the L or R jack. Use a

monaural-stereo cable (not supplied).

The left and right sounds are

unbalanced or reversed.

• Check that the speakers and components

are connected correctly and securely.

• Adjust the balance parameters by pressing

BALANCE on the remote.

There is severe hum or noise.

• Check that the speakers and components

are connected securely.

• Check that the connecting cords are away

from a transformer or motor, and at least 3

m away from a TV set or fluorescent light.

• Move your TV away from the audio

components.

• Make sure you have grounded the U

SIGNAL GND terminal (only when a

turntable is connected).

• The plugs and jacks are dirty. Wipe them

with a cloth slightly moistened with

alcohol.

Recording cannot be carried out.

• Check that the components are connected

correctly (page 7, 8).

• Select the source component using INPUT

SELECTOR (page 11, 12).

Sidan laddas ...

Sony Stereo Amplifier TA-FA1200ES Användarmanual

Denna manual är också lämplig för

Sony Stereo Amplifier TA-FA1200ES Användarmanual

på andra språk

Andra dokument