Hilti TE 500-A36 Bruksanvisningar

varumärke: Hilti

Modell: TE 500-A36

Typ: Bruksanvisningar

TE 500-A36

English 1

Dansk 12

Svenska 23

Norsk 34

Suomi 45

Eesti 56

Latviešu 67

Lietuvių 79

Türkçe 91

ﻋﺮﺑﻲ 102

日本語 114

한국어 125

繁體中文 136

中文 146

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

TE 500-A36

en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

da Original brugsanvisning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

sv Originalbruksanvisning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

no Original bruksanvisning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

fi Alkuperäiset ohjeet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

et Originaalkasutusjuhend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

lv Oriģinālā lietošanas instrukcija . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

lt Originali naudojimo instrukcija . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

tr Orijinal kullanım kılavuzu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

ja オリジナル取扱説明書 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

ko 오리지널 사용 설명서 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

zh 原始操作說明 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

cn 原版操作说明 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

*2240497*

2240497 English 1

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free

handling and use of the product.

• Observe the safety instructions and warnings in this documentation and on the product.

• Always keep the operating instructions with the product and make sure that the operating instructions

are with the product when it is given to other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶ Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶ Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶

Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage

to the equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

These numbers refer to the corresponding illustrations found at the beginning of these operating

instructions

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text

Item reference numbers are used in the overview illustrations and refer to the numbers used in

the product overview section

This symbol is intended to draw special attention to certain points when handling the product.

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols can be used on the product:

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

2 English 2240497

*2240497*

Chiseling

Chisel positioning

Service indicator

Diameter

Rated speed under no load

Revolutions per minute

Direct current (DC)

Wireless data transfer

Li-ion battery

Hilti Li-ion battery type series used. Observe the information given in the section headed In-

tended use.

1.4 Switching on and off

Symbols

Product is switched on

Product is switched off

1.5 Product information

products are designed for professional users and only trained, authorized personnel are

permitted to operate, service and maintain the products. This personnel must be specifically informed about

the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by

untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶ Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Breakers TE 500A36

Generation 04

Serial no.

1.6 Declaration of conformity

We declare, onour sole responsibility, that the product described here complies with the applicable directives

and standards. A copy of the declaration of conformity can be found at the end of this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

*2240497*

2240497 English 3

Work area safety

▶ Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶ Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶ Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

Electrical safety

▶ Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

▶ Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶ Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶ Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

▶ When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

▶ If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶ Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶ Use personal protective equipment. Always wear eye protection. Protective equipment such as a

dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will

reduce personal injuries.

▶ Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶ Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶ Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶ Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶ If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

▶ Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

▶ Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶ Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶ Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

▶ Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶ Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

▶ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

4 English 2240497

*2240497*

▶ Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

▶ Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

▶ Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with another battery pack.

▶ Use power tools only with specifically designated battery packs. Use of any other battery packs may

create a risk of injury and fire.

▶ When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a fire.

▶ Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

▶ Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may

exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

▶ Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature

above 130° C (265 °F) may cause explosion.

▶ Follow all charging instructions and do not charge the battery pack or tool outside the temperature

range specified in the instructions. Charging improperly or at temperatures outside the specified range

may damage the battery and increase the risk of fire.

Service

▶ Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

▶ Never service damaged battery packs. Service of battery packs should only be performed by the

manufacturer or authorized service providers.

2.2 Hammer safety warnings

Safety instructions for all operations

▶ Wear ear protectors. Exposure to noise can cause hearing loss.

▶ Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

▶ Hold the power tool by insulated gripping surfaces, when performing an operation where the

cutting accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and could give the operator an electric shock.

2.3 Additional safety instructions for breakers

Personal safety

▶ Use the product only when it is in technically faultless condition.

▶ Never tamper with or modify the tool in any way.

▶ When chiseling into ceilings, walls and floors, always make sure that you have a safe and firm stance. A

sudden break-through can affect your balance!

▶ Apply appropriate safety measures at the opposite side of the workpiece in work that involves breaking

through. Parts breaking away could fall out and / or fall down causing injury to other persons.

▶ You and any other persons in the vicinity must wear suitable eye protection, a hard hat, ear protection,

protective gloves and respiratory protection while the tool is in use.

▶ Wear protective gloves also when changing the accessory tool. Touching the accessory tool can result

in cuts and burns.

▶ Wear eye protection. Flying fragments can injure the body and eyes.

▶ Before starting work, check the hazard class of the dust that will be produced when working. Use

an industrial vacuum cleaner with an officially approved protection class in compliance with the locally

applicable dust protection regulations. Dust from materials such as lead-based paint, certain types of

wood and concrete/masonry/stone containing quartz, minerals or metal can be harmful to health.

▶ Make sure that the workplace is well ventilated and, where necessary, wear a respirator appropriate for

the type of dust generated. Contact with or inhalation of the dust may cause allergic reactions and/or

respiratory or other diseases among operators or bystanders. Certain kinds of dust are classified as

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

*2240497*

2240497 English 5

carcinogenic such as oak and beech dust, especially in conjunction with additives for wood conditioning

(chromate, wood preservative). Material containing asbestos may be handled only by specialists.

▶ Take breaks and do physical exercises to improve the blood circulation in your fingers. Exposure to

vibration during long periods of work can lead to disorders of the blood vessels and nervous system in

the fingers, hands and wrists.

Electrical safety

▶ Before beginning work, check the working area for concealed electric cables or gas and water pipes.

External metal parts of the power tool can become live, presenting a risk of electric shock, if you

accidentally damage an electric cable.

Careful handling and use of electric tools

▶ Wait until the power tool stops completely before you lay it down.

2.4 Battery use and care

▶ Observe the special regulations and instructions applicable to the transport, storage and use of Li-ion

batteries.

▶ Do not expose batteries to high temperatures, direct sunlight or fire.

▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C.

▶ Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height

or show signs of damage. In this case, always contact your Hilti Service.

▶ If the battery is too hot to touch it may be defective. In this case, place the product in a non-flammable

location, well away from flammable materials, where it can be kept under observation and allowed to

cool down. In this case, always contact your Hilti Service.

3 Description

3.1 Product overview 1

Chuck

;

Function selector switch

Lockbutton for sustained operation (chiseling

only)

Control switch

Charge-status and fault indicator (Li-ion bat-

tery)

(

Release buttons (also used to activate the

charge status indicator)

)

Battery

Side handle

On/off switch

Button for half power

Half-power indicator

∙

Service indicator

ON/OFF indicator

3.2 Intended use

The product described is a cordless (battery-powered) breaker with pneumatic hammering mechanism. The

product designed for light to medium chiseling work on masonry and surface finishing work on concrete.

▶ Use only Hilti Li-ion batteries from the B 36 series with this product.

▶ Use only the Hilti battery chargers from the C4/36 series for these batteries.

3.2.1 Possible misuse

• This product is not suitable for working on hazardous materials.

• This product is not suitable for working in a damp environment.

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

6 English 2240497

*2240497*

3.3 Active Vibration Reduction

The tool is equipped with an Active Vibration Reduction (AVR) system which reduces vibration noticeably.

3.4 Service indicator

The product is equipped with a service indicator LED.

3.4.1 MMI

Status Meaning

The Service indicator lights up.

Servicing is due.

The Service indicator flashes.

Have the product repaired by Hilti Service.

The ON/OFF indicator lights up. The product is switched on

The ON/OFF indicator flashes. The product is switched off because of a transient

fault.

The ON/OFF indicator is off. The product is switched off.

The Half power indicator lights up.

The product is working at half power.

The Half power indicator is off.

The product is working at full power.

3.4.2 Lithiumion battery status display

The Li-ion battery state of charge and malfunctions of the power tool are indicated by the display on the Liion

battery. The Liion battery state of charge is displayed after pressing one of the two battery release buttons.

Status Meaning

4 LEDs light. State of charge: 75 % to 100 %

3 LEDs light. State of charge: 50 % to 75 %

2 LEDs light. State of charge: 25 % to 50 %

1 LED lights. State of charge: 10 % to 25 %

1 LED blinks. State of charge: < 10 %

1 LED flashes, the product is not in working order. The battery has overheated or is completely dis-

charged.

4 LEDs flash, the product is not in working order. The power tool is overloaded or has overheated.

Battery state of charge cannot be displayed while the control switch is pressed and for up to 5 seconds

after releasing the control switch.

If the battery display LEDs blink, please observe the instructions given in the Troubleshooting section.

3.5 Items supplied

Breaker, side handle, operating instructions.

Other system products approved for use with this product can be found at your local Hilti Store or online at:

www.hilti.group.

4 Technical data

TE 500-A36

Rated voltage

36 V

Weight in accordance with EPTA procedure 01

7.9 kg

Chuck

TEY

Storage temperature

−20 ℃ … 70 ℃

Ambient temperature for operation

−17 ℃ … 60 ℃

4.1 Noise information and vibration values in accordance with EN 60745

The sound pressure and vibration values given in these instructions were measured in accordance with a

standardized test and can be used to compare one power tool with another. They can also be used for a

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

*2240497*

2240497 English 7

preliminary assessment of exposure. The data given represents the main applications of the power tool.

However, if the power tool is used for different applications, with different accessory tools, or is poorly

maintained, the data can vary. This can significantly increase exposure over the total working period. An

accurate estimation of exposure should also take into account the times when the tool is switched off, or

when it is running but not actually being used for a job. This can significantly reduce exposure over the

total working period. Identify additional safety measures to protect the operator from the effects of noise

and/or vibration, for example: Maintaining the power tool and accessory tools, keeping the hands warm,

organization of work patterns.

Noise emission values in accordance with EN 60745

TE 500-A36

Sound pressure level (LpA)

89 dB

Uncertainty for the sound pressure level (KpA)

3 dB

Sound power level (LWA)

100 dB

Uncertainty for the sound power level (KWA)

3 dB

Total vibration in accordance with EN 62841

TE 500-A36

Uncertainty (K)

1.5 m/s²

Chiseling in concrete (a

h, CHeq

)

6.7 m/s²

Uncertainty (K)

1.5 m/s²

5 Battery

Battery operating voltage

36 V

Ambient temperature for operation

−17 ℃ … 60 ℃

Storage temperature

−20 ℃ … 40 ℃

Battery charging starting temperature

−10 ℃ … 45 ℃

6 Operation

6.1 Preparations at the workplace

Switch the product off or remove the battery before making adjustments or changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

6.1.1 Inserting the battery

CAUTION

Risk of injury by short circuit or falling battery!

▶ Before inserting the battery, make sure that the contacts on the battery and the contacts on the product

are free of foreign matter.

▶ Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.

2. Push the battery into the battery holder until it engages with an audible click.

3. Check that the battery is seated securely.

6.1.2 Removing the battery

1. Press the release buttons on the battery.

2. Pull the battery out of its holder in the device.

6.1.3 Charging the battery

1. Before charging the battery, read the operating instructions for the charger.

2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.

3. Use an approved charger to charge the battery.

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

8 English 2240497

*2240497*

6.1.4 Fitting the side handle 2

CAUTION

Risk of injury! Loss of control over the breaker.

▶ Check that the side handle is fitted correctly and tightened securely.

1. Switch off the power tool.

2. Release the side handle clamping band by turning the handle grip.

3. Slide the side handle clamping band over the chuck from the front and into the recess provided.

4. Set the side handle to the desired position.

5. Tighten the side handle clamping band by turning the handle grip.

6.1.5 Setting the power level

After the battery is inserted, the product is always set by default to full power.

1. Press the "button for half power". The product runs at half power.

➥ The "half power indicator" lights up.

2. Press the "button for half power" again. The product runs at full power.

➥ The "half power indicator" goes out.

6.1.6 Inserting / removing the accessory tool 3

DANGER

Risk of fire! Risk of contact between the hot accessory tool and highly inflammable materials.

▶ Do not lay the hot accessory tool down on highly inflammable materials.

WARNING

Risk of injury! The tool becomes hot as a result of use.

▶ Wear protective gloves when changing the tool.

The use of unsuitable grease can cause damage to the product. Use only genuine Hilti grease.

1. Apply a little grease to the connection end of the accessory tool.

➥ Use only genuine Hilti grease. Using the wrong grease can result in damage to the product.

Set the function selector switch to the “Chiseling” position .

3. Push the accessory tool into the chuck as far as it will go (until it engages).

4. After fitting the accessory tool, grip it and pull it in order to check that it is securely engaged.

➥ The product is ready for use.

5. Pull the chuck ring back as far as it will go and remove the accessory tool.

6.2 Types of work

CAUTION

Risk of injury! Loss of control over the breaker.

▶ Check that the side handle is fitted correctly and tightened securely.

Observe the safety instructions and warnings in this documentation and on the product.

6.3 Chisel positioning 4

CAUTION

Risk of injury! Loss of control over the chisel direction.

▶ Do not operate the tool when the selector switch is set to “Chisel positioning”. Turn the function selector

switch until it engages in the “Chiseling” position.

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

*2240497*

2240497 English 9

The chisel can be set to 24 different positions (in 15° increments). This ensures that flat chisels and

shaped chisels can always be set to the optimum working position.

1. Switch off the power tool.

Set the function selector switch to the "Chisel positioning” position .

3. Turn the chisel to the desired position.

Set the function selector switch to this symbol: until it engages.

➥ The product is ready for use.

6.3.1 Chiseling

▶

Set the function selector switch to the "Chiseling" position .

Use both hands to hold the product firmly. Keep the product clean and free of oil and grease.

When the product is hot after working, do not place it on readily flammable materials. These

materials can ignite.

6.3.2 Switch sustained operation on and off 5

When chiseling, the control switch can be locked in the “on” position.

1. Push the lockbutton for continuous operation forward.

2. Press the control switch fully.

➥ The product then runs in sustained operating mode.

3. Push the lockbutton for continuous operation back.

➥ The product switches off.

7 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶ Always remove the battery before carrying out care and maintenance tasks!

Care and maintenance of the tool

• Carefully remove stubborn dirt.

• Clean the air vents carefully with a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

Care of the Liion batteries

• Keep the battery free from oil and grease.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these may attack the plastic parts.

• Avoid ingress of moisture.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired

immediately by Hilti Service.

• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with the product can be found at your

local Hilti Store or online at: www.hilti.group.

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

10 English 2240497

*2240497*

8 Transport and storage of cordless tools

Transport

CAUTION

Accidental starting during transport !

▶ Always transport your products with the batteries removed!

▶ Remove the battery.

▶ Never transport batteries in bulk form (loose, unprotected).

▶ Check the tool and batteries for damage before use after long periods of transport.

Storage

CAUTION

Accidental damage caused by defective or leaking batteries !

▶ Always store your products with the batteries removed!

▶ Store the tool and batteries in a place that is as cool and dry as possible.

▶ Never store batteries in direct sunlight, on heating units or behind a window pane.

▶ Store the tool and batteries in a place where they cannot be accessed by children or unauthorized

persons.

▶ Check the tool and batteries for damage before use after long periods of storage.

9 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

9.1 Troubleshooting

Trouble or fault Possible cause Action to be taken

No hammering action. The product is too cold. ▶ Bring the product into contact

with the working surface, switch

it on and allow it to idle. If

necessary, repeat the procedure

until the hammering mechanism

begins to operate.

The battery runs down more

quickly than usual.

Battery condition is not optimal. ▶ Replace the battery.

The battery does not en-

gage with an audible "double

click".

The retaining lugs on the battery

are dirty.

▶ Clean the retaining lugs and refit

the battery.

Product switches off auto-

matically.

The overload protection system is

active.

The ON/OFF indicator flashes.

▶ Release the control switch.

Allow the product to cool down.

Press the control switch again.

Reduce the load on the tool.

The power tool or battery

gets very hot.

Electrical fault. ▶ Immediately switch off the

product. Remove the battery

and keep it under observation.

Allow it to cool down. Contact

Hilti service.

The product is overloaded (appli-

cation limit exceeded).

▶ Select a product that is suitable

for the intended purpose.

No response from the LEDs

on the battery.

The battery is not fully inserted. ▶ Push the battery in until it

engages with a double click.

The battery is discharged. ▶ Change the battery and charge

the empty battery.

The battery is too hot or too cold. ▶ Bring the battery to the recom-

mended working temperature.

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

*2240497*

2240497 English 11

Trouble or fault Possible cause Action to be taken

1 LED on the battery flashes. The battery is discharged. ▶ Change the battery and charge

the empty battery.

The battery is too hot or too cold. ▶ Bring the battery to the recom-

mended working temperature.

4 LEDs on the battery flash. Product momentarily overloaded. ▶ Release the control switch and

then press it again.

Protection against overheating. ▶ Allow the product to cool down

and clean the air vents.

Product does not develop full

power.

The control switch is not fully

pressed.

▶ Press the control switch as far

as it will go.

The half-power button is engaged. ▶ Press the "half-power" button.

The insert tool cannot be re-

leased from the chuck.

The chuck is not pulled back fully. ▶ Pull the chuck back as far

as it will go and remove the

accessory tool.

The side handle is not fitted cor-

rectly.

▶ Disengage the side handle and

refit it correctly so that the

clamping band and side handle

engage in the recess.

Product does not start. The electronic restart interlock is

activated after an interruption in

the electric supply.

▶ Switch the product off and then

on again.

The service indicator lights. Service limit time reached. ▶ Have the product repaired by

Hilti Service.

The service indicator blinks. The product is faulty. ▶ Have the product repaired by

Hilti Service.

The ON/OFF indicator

flashes.

Product momentarily overloaded. ▶ Release the control switch and

then press it again.

Protection against overheating. ▶ Allow the product to cool down

and clean the air vents.

10 Disposal

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The

materials must be correctly separated before they can be recycled. In many countries, your old tools,

machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative

for further information.

▶ Do not dispose of power tools, electronic equipment or batteries as household waste!

11 RoHS (Restriction of Hazardous Substances)

Click on the link to go to the table of hazardous substances: qr.hilti.com/r10130182.

There is a link to the RoHS table, in the form of a QR code, at the end of this document.

12 Manufacturer’s warranty

▶ Please contact your local Hilti representative if you have questions about the warranty conditions.

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

12 Dansk 2240497

*2240497*

1 Oplysninger vedrørende dokumentationen

1.1 Vedrørende denne dokumentation

• Læs denne dokumentation igennem før ibrugtagning. Det er en forudsætning for sikkert arbejde og

korrekt håndtering.

• Følg sikkerheds- og advarselshenvisningerne i denne dokumentation og på produktet.

• Opbevar altid brugsanvisningen sammen med produktet, og overdrag det kun til andre personer sammen

med denne anvisning.

1.2 Tegnforklaring

1.2.1 Advarsler

Advarsler advarer mod farer ved håndtering af produktet. Følgende signalord anvendes:

FARE

FARE !

▶ Betegner en umiddelbart truende fare, der kan medføre alvorlige kvæstelser eller døden.

ADVARSEL

ADVARSEL !

▶ Står ved en potentielt truende fare, der kan medføre alvorlige kvæstelser eller døden.

FORSIGTIG

FORSIGTIG !

▶ Betegner en potentielt farlig situation, der kan forårsage lettere personskader eller materielle skader.

1.2.2 Symboler i denne dokumentation

Følgende symboler anvendes i denne dokumentation:

Læs brugsanvisningen før brug

Anvisninger for anvendelse og andre nyttige oplysninger

Håndtering af genvindbare materialer

Elektriske maskiner og batterier må ikke bortskaffes som almindeligt husholdningsaffald

1.2.3 Symboler i illustrationer

Følgende symboler anvendes på illustrationer:

Disse tal henviser til de forskellige illustrationer i begyndelsen af brugsanvisningen

Nummereringen udtrykker arbejdstrinnenes rækkefølge på illustrationen og kan afvige fra arbejds-

trinnene i teksten

Positionsnumre anvendes i illustrationen Oversigt og refererer til tallene i symbolforklaringen i

afsnittet Produktoversigt

Dette symbol skal sikre skærpet opmærksomhed ved omgang med produktet.

1.3 Produktspecifikke symboler

1.3.1 Symboler på produktet

Følgende symboler kan forekomme på produktet:

Mejsling

Placering af mejsel

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

*2240497*

2240497 Dansk 13

Serviceindikator

Diameter

Nominelt omdrejningstal, ubelastet

Omdrejninger pr. minut

Jævnstrøm

Trådløs dataoverførsel

Lithium-ion-batteri

Anvendt Hilti lithium-ion-batteriserie. Overhold oplysningerne i kapitlet Tilsigtet anvendelse.

1.4 Tænd/sluk

Symboler

Produktet er tændt

Produktet er slukket

1.5 Produktoplysninger

-produkter er beregnet til professionel brug og må kun betjenes, efterses og vedligeholdes af

autoriseret og instrueret personale. Dette personale skal i særdeleshed informeres om de potentielle farer,

der er forbundet med anvendelsen af denne maskine. Der kan opstå farlige situationer ved anvendelse af

produktet og det tilhørende udstyr, hvis det anvendes af personer, der ikke er blevet undervist i dens brug,

eller hvis det ikke anvendes korrekt i henhold til forskrifterne i denne brugsanvisning.

Typebetegnelse og serienummer fremgår af typeskiltet.

▶ Notér serienummeret i den efterfølgende tabel. Du skal bruge produktoplysningerne ved henvendelser til

vores lokale afdeling eller vores serviceværksted.

Produktoplysninger

Mejselhammer TE 500A36

Generation 04

Serienummer

1.6 Overensstemmelseserklæring

Vi erklærer som eneansvarlige, at det beskrevne produkt er i overensstemmelse med gældende direktiver og

standarder. Sidst i dette dokument finder du et bilede af overensstemmelseserklæringen.

Den tekniske dokumentation er arkiveret her:

Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE

2 Sikkerhed

2.1 Generelle sikkerhedsanvisninger for elværktøj

ADVARSEL Læs alle sikkerhedsanvisninger, henvisninger, billedtekster og tekniske data på

elværktøjet. Hvis følgende anvisninger ikke overholdes, er der risiko for elektrisk stød, brand og/eller

alvorlige personskader.

Opbevar alle sikkerhedsanvisninger og instruktioner til senere brug.

Det benyttede begreb "elværktøj" i sikkerhedsanvisningerne refererer til elektriske maskiner (med netledning)

eller batteridrevne maskiner (uden netledning).

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

14 Dansk 2240497

*2240497*

Arbejdspladssikkerhed

▶ Sørg for at holde arbejdsområdet ryddeligt og godt oplyst. Uorden eller uoplyste arbejdsområder

øger faren for uheld.

▶ Brug ikke elværktøj i eksplosionstruede omgivelser, hvor der er brændbare væsker, gasser eller

støv. Elværktøj kan slå gnister, der kan antænde støv eller dampe.

▶ Sørg for, at andre personer og ikke mindst børn holdes væk fra arbejdsområdet, når elværktøjet

er i brug. Hvis man distraheres, kan man miste kontrollen over maskinen.

Elektrisk sikkerhed

▶ Elværktøjets stik skal passe til kontakten. Stikket må under ingen omstændigheder ændres. Brug

ikke adapterstik sammen med jordforbundne elværktøj. Uændrede stik, der passer til kontakterne,

nedsætter risikoen for elektrisk stød.

▶ Undgå kropskontakt med jordforbundne overflader som f.eks. rør, radiatorer, komfurer og

køleskabe. Hvis din krop er jordforbundet, øges risikoen for elektrisk stød.

▶ Elværktøj må ikke udsættes for regn eller fugt. Indtrængning af vand i elværktøj øger risikoen for

elektrisk stød.

▶ Brug ikke ledningen til formål, den ikke er beregnet til (f.eks. må man aldrig bære elværktøjet i

ledningen, hænge det op i ledningen eller rykke i ledningen for at trække stikket ud af kontakten).

Beskyt ledningen mod varme, olie, skarpe kanter eller dele, der er i bevægelse. Beskadigede eller

sammenviklede ledninger øger risikoen for elektrisk stød.

▶ Hvis elværktøjet benyttes i det fri, må der kun benyttes en forlængerledning, der er egnet til

udendørs brug. Brug af forlængerledning til udendørs brug nedsætter risikoen for elektrisk stød.

▶ Hvis det ikke kan undgås at anvende elværktøjet i fugtige omgivelser, skal du anvende et

fejlstrømsrelæ. Anvendelsen af et fejlstrømsrelæ nedsætter risikoen for et elektrisk stød.

Personlig sikkerhed

▶ Det er vigtigt at være opmærksom, se, hvad man laver, og bruge maskinen fornuftigt. Anvend aldrig

elværktøj, hvis du er træt eller påvirket af stoffer, alkohol eller medicin. Et øjebliks uopmærksomhed

under brugen af elværktøjet kan medføre alvorlige personskader.

▶ Brug beskyttelsesudstyr, og hav altid beskyttelsesbriller på. Brug af sikkerhedsudstyr som f.eks.

støvmaske, skridsikkert fodtøj, beskyttelseshjelm eller høreværn afhængigt af elværktøjets type og

anvendelse nedsætter risikoen for personskader.

▶ Undgå utilsigtet igangsætning. Kontrollér, at elværktøjet er frakoblet, før du slutter det til

strømforsyningen og/eller batteriet, tager det op eller transporterer det. Undgå at bære elværktøjet

med fingeren på afbryderen, og sørg for, at det ikke er tændt, når det sluttes til nettet, da dette øger

risikoen for personskader.

▶ Fjern indstillingsværktøj eller skruenøgler, inden elværktøjet tændes. Hvis et stykke værktøj eller en

nøgle sidder i en roterende maskindel, er der risiko for personskader.

▶ Undgå at arbejde i unormale kropsstillinger. Sørg for at stå sikkert, mens der arbejdes, og kom

ikke ud af balance. Det er derved nemmere at kontrollere elværktøjet, hvis der skulle opstå uventede

situationer.

▶ Brug egnet arbejdstøj. Undgå løse beklædningsgenstande eller smykker. Hold hår, tøj og handsker

væk fra dele, der bevæger sig. Dele, der er i bevægelse, kan gribe fat i løstsiddende tøj, smykker eller

langt hår.

▶ Hvis støvudsugnings- og opsamlingsudstyr kan monteres, er det vigtigt, at dette tilsluttes og

benyttes korrekt. Ved at anvende en støvudsugning er det muligt at nedsætte risiciene som følge af

støv.

▶ Man må ikke ignorere sikkerhedsreglerne for elværktøj, heller ikke selvom man er fortrolig med

brugen af elværktøjet. Uagtsomhed kan medføre alvorlig tilskadekomst inden for få sekunder.

Anvendelse og pleje af elværktøjet

▶ Undgå at overbelaste maskinen. Brug altid en maskine, der er beregnet til det stykke arbejde,

der skal udføres. Med det rigtige værktøj arbejder man bedst og mest sikkert inden for det angivne

effektområde.

▶ Brug ikke elværktøj, hvis afbryderen er defekt. En maskine, der ikke kan startes og stoppes, er farlig

og skal repareres.

▶ Træk stikket ud af stikkontakten, og/eller fjern batteriet fra maskinen, inden du foretager

indstillinger på den, skifter tilbehør og dele eller lægger den til side. Disse sikkerhedsforanstaltninger

forhindrer utilsigtet start af elværktøjet.

▶ Opbevar ubenyttede elværktøjer uden for børns rækkevidde. Lad aldrig personer, der ikke er

fortrolige med maskinen eller ikke har gennemlæst sikkerhedsanvisningerne, benytte denne.

Elværktøj er farligt, hvis det benyttes af ukyndige personer.

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

*2240497*

2240497 Dansk 15

▶ Sørg for at pleje elværktøj omhyggeligt. Kontrollér, om bevægelige dele fungerer korrekt og

ikke sidder fast, og om delene er brækket eller beskadiget, således at elværktøjets funktion

påvirkes. Få beskadigede dele repareret, inden elværktøjet tages i brug. Mange uheld skyldes

dårligt vedligeholdte elværktøjer.

▶

Sørg for, at skæreværktøjer er skarpe og rene. Omhyggeligt vedligeholdte skæreværktøjer med

skarpe skærekanter sætter sig ikke så hurtigt fast og er nemmere at føre.

▶ Anvend elværktøj, tilbehør, indsatsværktøj osv. i overensstemmelse med disse anvisninger. Tag

hensyn til arbejdsforholdene og det arbejde, der skal udføres. I tilfælde af anvendelse af maskinen til

formål, som ligger uden for det fastsatte anvendelsesområde, kan der opstå farlige situationer.

▶ Sørg for, at greb og gribeflader er tørre, rene og fri for olie og fedt. Glatte greb og gribeflader gør

betjeningen usikker, og det kan være svært at styre elværktøjet i uforudsete situationer.

Anvendelse og pleje af batteridrevet elværktøj

▶ Oplad kun batterier i ladere, der er anbefalet af fabrikanten. Der er risiko for brand, hvis en lader, der

er beregnet til et bestemt batteri, anvendes til opladning af en anden batteritype.

▶ Brug kun de batterier, der er beregnet til elværktøjet. Brug af andre batterier øger risikoen for

personskader og er forbundet med brandfare.

▶ Ikke benyttede batterier må ikke komme i berøring med kontorclips, mønter, nøgler, søm, skruer

eller andre små metalgenstande, da disse kan kortslutte kontakterne. En kortslutning mellem

batterikontakterne øger risikoen for personskader i form af forbrændinger.

▶ Hvis batteriet anvendes forkert, kan der løbe væske ud af batteriet. Undgå at komme i kontakt

med denne væske. Hvis det alligevel skulle ske, skylles med vand. Søg læge, hvis væsken kommer

i øjnene. Batterivæske kan give hudirritation eller forbrændinger.

▶ Brug aldrig et beskadiget eller ændret batteri. Beskadigede eller ændrede batterier kan virke utilsigtet

og medføre brand, eksplosion eller risiko for tilskadekomst.

▶ Batterier må ikke udsættes for åben ild eller høje temperaturer. Ild eller temperaturer over 130 °C

(265 °F) kan medføre eksplosion.

▶ Følg alle anvisninger vedrørende opladning, og oplad aldrig batteriet eller det batteridrevne

værktøj uden for det temperaturområde, der er anført i betjeningsvejledningen. Forkert opladning

eller opladning uden for det tilladte temperaturområde kan ødelægge batteriet og øge risikoen for brand.

Service

▶ Sørg for, at elværktøjet kun repareres af kvalificerede fagfolk, og at der altid benyttes originale

reservedele. Dermed sikres størst mulig elværktøjssikkerhed.

▶ Forsøg aldrig at reparere beskadigede batterier. Al vedligeholdelse af batterier skal foretages af

producenten eller af autoriserede forhandlere.

2.2 Sikkerhedsanvisninger til hamre

Sikkerhedsanvisninger for alle opgaver

▶ Brug høreværn. Støjpåvirkningen kan medføre høretab.

▶ Brug de ekstrahåndgreb, som følger med maskinen. Hvis du mister kontrollen, kan det medføre

personskader.

▶ Hold maskinen på de isolerede grebsflader, når du udfører opgaver, hvor indsatsværktøjet kan

ramme skjulte strømledninger. Ved kontakt med en spændingsførende ledning kan også metalliske

værktøjsdele sættes under spænding, hvilket kan medføre elektrisk stød.

2.3 Yderligere sikkerhedsanvisninger, mejselhammer

Personlig sikkerhed

▶ Anvend kun produktet i teknisk fejlfri stand.

▶ Foretag aldrig manipulationer eller ændringer på maskinen.

▶ Ved mejsling af lofter, vægge og gulve er det vigtigt at stå sikkert og stabilt. Hvis værktøjet pludselig går

igennem, kan du miste balancen!

▶ Ved gennembrydningsarbejde skal du huske at sikre området på den modsatte side. Nedbrydningsdele

kan falde ud og/eller ned og volde skade på andre personer.

▶ Sørg for, at du selv og personer, som opholder sig i nærheden under brugen af maskinen, anvender

egnede beskyttelsesbriller, sikkerhedshjelm, høreværn, beskyttelseshandsker og et let åndedrætsværn.

▶ Brug også beskyttelseshandsker, når du skifter værktøj. Berøring af indsatsværktøjet kan medføre snitsår

og forbrændinger.

▶ Brug øjenværn. Splinterne fra materialet kan medføre skader på legeme og øjne.

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

16 Dansk 2240497

*2240497*

▶ Find ud af, hvilken fareklasse det støv, der opstår ved arbejdet, har, inden du går i gang med arbejdet.

Anvend en industristøvsuger med en officielt tilladt beskyttelsesklassificering, som opfylder de lokale

støvbeskyttelsesbestemmelser. Støv fra materialer såsom blyholdig maling, visse træsorter, beton /

murværk / natursten, som indeholder kvarts, og mineraler samt metal kan være sundhedsfarlige.

▶

Sørg for en god ventilation af arbejdspladsen, og brug om nødvendigt et åndedrætsværn, som egner sig

til den pågældende støvtype. Berøring eller indånding af støv kan medføre allergiske reaktioner og/eller

luftvejssygdomme hos brugeren eller personer, der opholder sig i nærheden. Bestemte støvtyper,

f.eks. støv fra ege- og bøgetræ, er kræftfremkaldende, især i forbindelse med tilsætningsstoffer til

træbehandling (kromat, træbeskyttelsesmidler). Asbestholdige materialer må kun håndteres af fagfolk.

▶ Hold pauser under arbejdet, og lav øvelser, så dine fingre får en bedre blodgennemstrømning. Ved

længerevarende arbejde kan vibrationermedføre forstyrrelser af fingrenes, hændernes eller håndleddenes

blodkar og nervesystem.

Elektrisk sikkerhed

▶ Kontrollér før påbegyndelse af arbejdet arbejdsområdet for skjulte elektriske ledninger, gas- og vandrør,

f.eks. med en metaldetektor. Udvendige metaldele på maskinen kan medføre elektrisk stød, hvis du ved

en fejl kommer til at beskadige en elledning.

Omhyggelig omgang med og brug af elværktøj

▶ Vent, indtil elværktøjet er standset helt, før du lægger det fra dig.

2.4 Omhyggelig omgang med og brug af batterier

▶ Læs de særlige retningslinjer for transport, opbevaring og brug af lithiumion-batterier.

▶ Hold batterier på sikker afstand af høje temperaturer, direkte solindstråling og ild.

▶ Batterierne må ikke adskilles, klemmes, opvarmes til over 80 °C eller brændes.

▶ Anvend og oplad ikke batterier, som har fået et slag, er faldet på gulvet fra mere end en meters højde

eller på anden vis er blevet beskadiget. Kontakt i så fald altid Hilti Service.

▶ Hvis batteriet er for varmt til at kunne røres, kan det være defekt. Placer produktet på et ikke-brændbart

sted i tilstrækkelig afstand til brændbare materialer, hvor det er muligt at holde øje med det, og lad det

køle af. Kontakt i så fald altid Hilti Service.

3 Beskrivelse

3.1 Produktoversigt 1

Værktøjsholder

;

Funktionsvælger

Låseknap til permanent drift (kun mejsling)

Afbryder

Ladetilstands- og fejlvisning (lithium-ion-

batteri)

(

Frigøringsknapper med ekstrafunktion til

aktivering af ladetilstandsvisning

)

Batteri

Sidegreb

Tænd/sluk-knap

Knap til halv effekt

Visning for halv effekt

∙

Serviceindikator

Til/Fra-indikator

3.2 Bestemmelsesmæssig anvendelse

Det beskrevne produkt er en batteridrevet mejselhammer med pneumatisk slagmekanisme. Produktet er

beregnet til lette og moderate mejselopgaver i murværk og til efterbearbejdning af beton.

▶ Anvend kun Hilti lithium-ion-batterier i typeserien B 36 til dette produkt.

▶ Anvend kun Hilti ladere i C4/36-serien til disse batterier.

Printed: 16.07.2019 | Doc-Nr: PUB / 5503718 / 000 / 00

Sidan laddas ...

Hilti TE 500-A36 Bruksanvisningar

varumärke: Hilti

Modell: TE 500-A36

Typ: Bruksanvisningar

Ladda ner pdf

Rapportera

på andra språk

eesti: Hilti TE 500-A36 Kasutusjuhend
日本語: Hilti TE 500-A36 取扱説明書
Türkçe: Hilti TE 500-A36 Kullanma talimatları
dansk: Hilti TE 500-A36 Betjeningsvejledning

Hilti TE 500-A36 Bruksanvisningar

Hilti TE 500-A36 Bruksanvisningar

på andra språk

Relaterade papper