Samsung DW50R4040BB Användarmanual

Dishwasher

Eco Design Guide

WEB_Dishwaser_Global_00_EN.indd 1 2021-04-09  12:01:11

English2

Contents

Installation 3

Installation requirements 3

Before you start 4

Using Detergent 4

Using Rinse 9

Using Softener 12

Operations 14

Cycle overview 14

Energy, water saving tip 15

Cycle chart 16

Maintenance 23

Cleaning 23

Troubleshooting 27

Checkpoints 27

Information codes 30

WEB_Dishwaser_Global_00_EN.indd 2 2021-04-09  12:01:11

English 3

Installation

Installation requirements

To prevent a risk of re, electric shock, or

personal injury, all wiring and grounding

must be done by a qualied technician.

Power supply

• An individual 220-240 V

~

, 50 Hz

branch circuit that is dedicated to the

dishwasher.

• Power outlet with a maximum allowable

current of 16 A (maximum 11 A for the

dishwasher)

WARNING

• Do not use an extension cord.

• Use only the power plug that comes

with the dishwasher.

• After installation is complete, make sure

the power plug is not bent or damaged.

Grounding

For permanent grounding, the dishwasher

must be properly grounded to a grounded

metal or permanent wiring system. The

grounding conductor must be run with

the circuit conductors and then connected

to the grounding terminal or lead on the

dishwasher.

WARNING

• Do not connect the ground wire to

plastic plumbing, gas lines, or hot water

pipes. Improperly connected grounding

conductors may cause electric shock.

• Do not modify the power plug of the

dishwasher. If the power plug does

not t the outlet, have a proper outlet

installed by a qualied electrician.

Water supply

• The water supply line must support

water pressures between 0.04 and

1 MPa.

• Water temperatures must be lower than

60 °C.

• A stopcock with a 3/4” male thread must

be installed on the water tap.

To reduce a risk of leaks:

• Make sure water taps are easily

accessible.

• Turn the water tap off when the

dishwasher is not in use.

• Check for any leaks at the water hose

ttings on a regular basis.

• To stop any leak, seal the water line

connections and joints using Teon tape

or sealing compound.

Aqua Stop

The Aqua Stop is an electrical component

that is designed to prevent water leaks. The

Aqua Stop is attached to the water hose

and automatically cuts off the water ow in

the event of damage to the hose.

CAUTION

• Handle the Aqua Stop with care.

• Do not kink or twist the water hose

connected to the Aqua Stop. If the Aqua

Stop is damaged, shut off the water taps

and unplug the power plug immediately.

Then, contact a local Samsung customer

centre or a qualied technician.

Flooring

• Make sure the dishwasher is level using

the height adjustable feet.

• When levelling is complete, check if the

door opens and closes properly.

WEB_Dishwaser_Global_00_EN.indd 3 2021-04-09  12:01:11

English4

Before you start

There are two types of dispenser as follows. Check the instructions for the right dispenser

for your dishwasher.

Type A Type B

Using Detergent

Detergent compartment

All dishwasher cycles require detergent in the detergent compartment. Apply detergent as

recommended for the selected cycle to ensure best performance.

WARNING

• Do not place dishwasher detergent in your mouth. Avoid breathing in detergent

fumes. Dishwasher detergent contains irritants and caustic chemicals that can induce

respiratory conditions. If you have consumed dishwasher detergent or inhaled

detergent fumes, seek medical attention immediately.

• Keep dishwasher detergent out of children’s reach.

CAUTION

• Use dishwasher detergent only. Other types of detergent produce excessive foam, which

may decrease the dishwasher’s performance or cause it to malfunction.

• The dishwasher may not wash well if there is not much detergent. For normally

soiled items, we recommend 20-25 grams; however, this may differ depending on the

detergent manufacturer, so please follow that manufacturer’s recommendations.

• We recommend 15-20 grams for DW5******** models.

WEB_Dishwaser_Global_00_EN.indd 4 2021-04-09  12:01:11

English 5

Before you start

Filling the detergent

- Type A

1. Open the detergent dispenser cap by

pushing the detergent dispenser catch

to the right.

NOTE

The cap remains open at the end of a cycle.

2. Add the recommended amount of

detergent to the main wash detergent

compartment.

3. Close the lid by sliding it up.

WEB_Dishwaser_Global_00_EN.indd 5 2021-04-09  12:01:11

English6

Before you start

4. If the items are heavily soiled, pour a

small amount of detergent onto the door

for better cleaning results.

NOTE

The additional detergent will activate

during the pre-wash process.

The cover opens automatically to dispense the detergent during the wash.

WEB_Dishwaser_Global_00_EN.indd 6 2021-04-09  12:01:11

English 7

Before you start

- Type B

1. Open the detergent dispenser ap by

pushing the detergent dispenser release

catch.

NOTE

The ap is always open at the end of a

dishwashing cycle.

2. Add the recommended amount of

detergent to the main wash detergent

compartment.

3. Close the ap by sliding it to the left

and then pressing it down.

NOTE

There is no separate button that is specic

to using tablet detergents.

WEB_Dishwaser_Global_00_EN.indd 7 2021-04-09  12:01:11

English8

Before you start

4. If the items are heavily soiled, pour a

small amount of detergent onto the door

for better cleaning results.

NOTE

The additional detergent will activate

during the pre-wash process.

The cover opens automatically to dispense the detergent during the wash.

WEB_Dishwaser_Global_00_EN.indd 8 2021-04-09  12:01:12

English 9

Before you start

Using Rinse

Rinse aid reservoir

Rinse aid improves the drying performance of the dishwasher. When the Rinse Rell

indicator lights up on the control panel, rell with rinse aid. Only use liquid rinse aid.

Powdered rinse aid will clog the reservoir opening and cause the dishwasher to

malfunction.

CAUTION

• Do not apply any type of detergent to the rinse aid reservoir.

• Do not excessively ll the reservoir. Excessive rinse aid may overow during a cycle.

Filling the rinse aid

- Type A

1. Open the rinse aid reservoir cap.

NOTE

Adding rinse aid to tablet detergents will

improve drying performance.

2. Fill the rinse aid reservoir with rinse aid.

CAUTION

Do not ll the reservoir above the full level

indicator. Excess rinse aid can overow

during the wash cycle.

WEB_Dishwaser_Global_00_EN.indd 9 2021-04-09  12:01:12

English10

Before you start

3. Close the rinse aid reservoir cap.

Rinse aid setting

You can change the amount of rinse aid applied during a cycle.

The buttons used to enter the setting mode may vary depending on the model.

Check the buttons for your model.

• DW6*R70**** / DW5*R407*BB / DW5*R406*BB : A (AUTO), B (Sanitize)

• DW5*R405*BB / DW5*R404*BB : A (Normal), B (Sanitize)

• DW5*R40**F* : A (Program), B (Rinse Add)

1. Press and hold the A button for ve seconds.

2. Press the B button to select the rinse aid level setting menu.

- The display shows the current setting. (Default setting: ‘d4’)

3. Press the A button to change the setting.

- You can select from d1-d5 (minimum-maximum)

4. Wait 5 seconds to save the setting.

• DW6*M5***BB / DW60M5070IB : A (Express)

• DW6*M5***F*/S*/U* models : A (Program)

1. Press and hold the A button for ve seconds.

2. Press the Delay Start button to enter the Rinse aid setting mode.

- The display shows the current setting.

3. Press the A button to select the amount of rinse aid you want.

- You can select from d1-d5 (minimum-maximum)

4. Wait 5 seconds to save the setting.

WEB_Dishwaser_Global_00_EN.indd 10 2021-04-09  12:01:12

English 11

Before you start

- Type B

1. Remove the rinse aid reservoir cap by

rotating it counterclockwise.

NOTE

Adding rinse aid to tablet detergents will

improve drying performance.

2. Fill the rinse aid reservoir with rinse aid.

NOTE

Use the viewing port when lling the rinse

aid reservoir.

CAUTION

Do not ll the reservoir above the full level

indicator. Excess rinse aid can overow

during the wash cycle.

3. Turn the rinse aid indicator dial to a

number between 1 and 6.

- The higher the number, the more

rinse aid the dishwasher uses.

- To improve the drying performance,

select a higher level.

- If there is discoloring on the dishes,

switch to a lower level.

- If you are unable to rotate the rinse

aid dial easily, try using a coin.

4. Close the rinse aid reservoir cap by

rotating it clockwise.

WEB_Dishwaser_Global_00_EN.indd 11 2021-04-09  12:01:12

English12

Before you start

Using Softener

Salt storage

The water softener is designed to remove minerals from the water, which would have a

detrimental or adverse effect on the operation of the appliance. We recommend using

soft water for better results. Hard water contains impurities that can reduce the washing

performance. You will need to soften the water if the supplied water is harder than

1.0 mmol/l (6 °d - German scale).

• To soften the water, you need dishwasher-specic salt and conguration of the water

hardness level according to your area. For more information about the water hardness

level in your area, contact your local water department.

• If the hardness level of the supplied water supply is unsteady, set the dishwasher to

the highest measurement. For example, if the water hardness reading ranges from

6.7 mmol/l to 9.0 mmol/l, set the dishwasher to 9.0 mmol/l.

• The dishwasher’s default water hardness level is 3 (2.1-3.0 mmol/l). If this setting

matches the water hardness level in your area, you do not need to change it.

NOTE

• It is recommended that adjustments should be made in accordance with the following

(or Manual) table.

• The manufactory setting: H3

Water hardness

Water

hardness

setting

Salt

consumption

(gram/cycle)

Autonomy

(cycles/1 kgs)

°dH °fH °Clark mmol/l

0-5 0-9 0-6 0-0.94 H1 0 /

6-11 10-20 7-14 1.0-2.0 H2 20 60

12-17 21-30 15-21 2.1-3.0 H3 30 50

18-22 31-40 22-28 3.1-4.0 H4 40 40

23-34 41-60 29-42 4.1-6.0 H5 50 30

35-55 61-98 43-69 6.1-9.8 H6 60 20

NOTE

• 1 dH (German degree) = 0.178 mmol/l

• 1 Clark (British degree) = 0.143 mmol/l

• 1 fH (French degree) = 0.1 mmol/l

• Contact your local water board for information on the hardness of your water supply.

WEB_Dishwaser_Global_00_EN.indd 12 2021-04-09  12:01:12

English 13

Before you start

NOTE

How water softener regeneration works (ECO cycle with H3 level setting)

• Operates for about 2 minutes when drying starts and uses 2 L water, 0.0002 kWh

energy

• Regenerates once every 5 cycles

How to set the softener level

The dishwasher is designed to allow for adjusting the amount of salt consumed based on

the hardness of the water used. This is intended to optimise and customise the level of salt

consumption so that the salt consumption could be set proceed as follows:

The buttons used to enter the setting mode may vary depending on the model.

Check the buttons for your model.

• DW6*R70**** / DW5*R407*BB / DW5*R406*BB : A (AUTO)

• DW5*R405*BB / DW5*R404*BB : A (Normal)

1. Press and hold the A button for ve seconds.

2. Press the Delay Start button to select the water hardness level setting menu.

- The display shows the current setting.

3. Press the A button to change the setting.

- You can select from H1-H6 (soft - hard)

4. Wait 5 seconds to save the setting.

• DW6*M6***BB / DW60M6070IB : A (Pre Wash)

• DW6*M5***BB / DW60M5070IB : A (Express)

• DW6*M****F*/S*/U* models : A (Program)

1. Press the A button for ve seconds to select the water hardness level setting menu.

- The display shows the current setting.

2. Press the A button to change the setting.

- You can select from H1-H6 (soft - hard)

3. Wait 5 seconds to save the setting.

WEB_Dishwaser_Global_00_EN.indd 13 2021-04-09  12:01:12

English14

Operations

Cycle overview

ECO *

This cycle reduces power and water consumption, which is

appropriate for normally soiled items

AUTO /

Auto wash

This cycle detects the level of soil and automatically

initiates the optimal cycle, which is appropriate for all

levels of soiled items.

Normal

For normally soiled loads, such as pots, plates, glasses, and

lightly soiled pans.

Intensive Select this cycle for heavily soiled items.

Delicate

Select this cycle for lightly soiled, fragile items such as

glasses.

Express Normally soiled daily using items, with short cycle time.

Quick /

Quick wash

Select this cycle to clean lightly soiled items in a short

time.

Pre Wash

Cold water rinse for removing dirt before running another

program.

Extra Silence

Select this cycle for more smooth and quiet washing. This

cycle washes a little bit slower, but creates 2 decibels less

noise than the ECO program.

Self Clean

Select this cycle to clean the inside of the dishwasher.

Make sure the dishwasher is empty.

The cycle used may vary depending on the model.

* The values for the ECO program have been obtained following the test standard EN

60436:2020. The values given for the other programs are indicative only.

WEB_Dishwaser_Global_00_EN.indd 14 2021-04-09  12:01:12

English 15

Operations

Energy, water saving tip

• ECO programme is suitable to clean normally soiled tableware, that for this use, it is

the most efcient programme in terms of its combined energy and water consumption,

and that it is used to assess compliance with the EU ecodesign legislation (COMMISSION

REGULATION (EU) 2019/2022).

• Manual pre-rinsing of tableware items leads to increased water and energy

consumption and is not recommended.

Use a knife, etc. to remove only large bits of food before loading.

• Water supplied can be up to 60 °C, and less power is consumed when hot water is

connected.

• It’s better to ll the basket if possible but without overloading.

• To save water and energy, use the ECO cycle. ECO is the most efcient program when

washing normally soiled items.

• Use an appropriate amount of detergent and rinse according to the manufacturer’s

guidelines.

• Dishwasher use saves water compared to ordinary washing by hand.

• Ecodesign information can be found by going to www.samsung.com/support.

To access the EPREL registration of the model :

1. Go to https://eprel.ec.europa.eu

2. Get the model identier from the energy label of the product and type it in the search

box

3. Energy Labelling information of the model is shown

* You can directly access the product information via https://eprel.ec.europa.eu/qr/######

(registration no.)

The registration no. can be found on the rating label on your product.

WEB_Dishwaser_Global_00_EN.indd 15 2021-04-09  12:01:12

English16

Operations

Cycle chart

DW6*R707***/DW6*R705***/DW6*R704***

Cycle AUTO ECO Intensive

Amount of food

remains

Normal Normal Heavy

Cycle sequence

Pre wash (45 °C) 

Main wash (55 °C-

65 °C)  Rinse 

Hot rinse (50 °C -

70 °C)  Dry  End

Pre wash 

Main wash (50 °C) 

Rinse 

Hot rinse (48 °C) 

Dry  End

Pre wash (50 °C) 

Main wash (65 °C)

 Rinse 

Hot rinse (58 °C) 

Dry  End

Water consumption

(L)

8.5-18 9.9 16.6

Energy consumption

(kWh)

0.85-1.55

0.848

(DW6*R707***/

DW6*R705***)

0.836

(DW6*R704***)

1.5

Cycle time (min.) 150 210 205

Cycle Delicate Express * Pre Wash

Amount of food

remains

Light Normal Light

Cycle sequence

Pre wash (40 °C) 

Main wash (50 °C) 

Rinse 

Hot rinse (50 °C) 

Dry  End

Main wash (60 °C)

 Rinse 

Hot rinse (55 °C) 

Dry  End

Pre wash  End

Water consumption

(L)

13.5 15 4.1

Energy consumption

(kWh)

0.95 0.95 0.02

Cycle time (min.) 120 60 15

WEB_Dishwaser_Global_00_EN.indd 16 2021-04-09  12:01:12

English 17

Operations

Cycle Extra Silence ** Self Clean

Amount of food

remains

Normal -

Cycle sequence

Pre wash (35 °C) 

Main wash (60 °C) 

Rinse 

Hot rinse (55 °C) 

Dry  End

Pre wash 

Main wash (70 °C) 

Rinse 

Hot rinse (70 °C) 

Dry  End

Water consumption

(L)

13 15

Energy consumption

(kWh)

1.5 1.25

Cycle time (min.) 270 145

* Pre Wash : This cycle does not activate the Auto Door function nor the drying process.

Continuous use of the Pre Wash cycle for an extended time is not

recommended. This may reduce the performance of the water softener.

** Self Clean : Only for DW6*R707*/DW6*R705* models

NOTE

The power consumption and cycle time depends on the water temperature and/or load.

WEB_Dishwaser_Global_00_EN.indd 17 2021-04-09  12:01:12

English18

Operations

DW5*R407***/DW5*R406***

Cycle AUTO ECO Intensive

Amount of food

remains

Very light to heavy Normal Heavy

Cycle sequence

Pre wash (45 °C) 

Main wash (45 °C-

55 °C)  Rinse 

Hot rinse (65 °C) 

Dry  End

Main wash (50 °C)

 Rinse  Hot

rinse (50 °C)  Dry 

End

Pre wash (50 °C) 

Main wash (60 °C)

 Rinse  Rinse 

Hot rinse (70 °C) 

Dry  End

Water consumption

(L)

9.5-13

9.9 (DW5*R406***)

9.5 (DW5*R407***)

15.5

Energy consumption

(kWh)

0.85-1.2

0.704 (DW5*R406***)

0.755 (DW5*R407***)

1.33

Cycle time (min) 150 220 175

Cycle Delicate Express Quick

Amount of food

remains

Light Normal Light

Cycle sequence

Pre wash 

Main wash (40 °C)

 Rinse  Hot

rinse (60 °C) 

Dry  End

Pre wash (40 °C) 

Main wash (45 °C) 

Hot rinse (60 °C) 

Dry  End

Main wash (35 °C) 

Rinse (35 °C)

Water consumption

(L)

12 9.1 10.5

Energy consumption

(kWh)

0.71 0.77 0.28

Cycle time (min) 125 60 20

WEB_Dishwaser_Global_00_EN.indd 18 2021-04-09  12:01:12

English 19

Operations

DW5*R405***/DW5*R404***

Cycle Normal ECO Intensive

Amount of food

remains

Normal Normal Heavy

Cycle sequence

Pre wash (45 °C) 

Main wash (55 °C)

 Rinse 

Hot rinse (65 °C) 

Dry  End

Main wash (45 °C)

 Rinse  Hot

rinse (60 °C)  Dry 

End

Pre wash (50 °C) 

Main wash (60 °C)

 Rinse  Rinse 

Hot rinse (70 °C) 

Dry  End

Water consumption

(L)

13.1

9.5 (DW5*R404***)

9.9 (DW5*R405***)

16.5

Energy consumption

(kWh)

1.1

0.780 (DW5*R404***)

0.836 (DW5*R405***)

1.3

Cycle time (min) 175 220 165

Cycle Delicate Express Quick

Amount of food

remains

Light Normal Light

Cycle sequence

Pre wash 

Main wash (40 °C)

 Rinse  Hot

rinse (60 °C) 

Dry  End

Pre wash (50 °C) 

Main wash (60 °C) 

Hot rinse (60 °C) 

Dry  End

Main wash (35 °C)

 Rinse (35 °C)

Water consumption

(L)

13.4 9.1 10.5

Energy consumption

(kWh)

0.78 0.75 0.3

Cycle time (min) 125 60 20

NOTE

The power consumption and cycle time depends on the water temperature and/or load.

WEB_Dishwaser_Global_00_EN.indd 19 2021-04-09  12:01:12

English20

Operations

DW6*M503***/DW6*M505***/DW60M5070IB

Cycle Intensive Normal ECO

Amount of food

remains

Heavy Normal Normal

Cycle sequence

Pre wash (50 °C) 

Main wash (60 °C)

 Rinse  Rinse 

Hot rinse (70 °C) 

Dry  End

Pre wash (45 °C) 

Main wash (55 °C)

 Rinse 

Hot rinse (65 °C) 

Dry  End

Main wash (45 °C)

 Rinse  Hot rinse

(65 °C)  Dry  End

Water consumption

(L)

18.5 15 12

Energy consumption

(kWh)

1.5 1.35 1.037

Cycle time (min) 170 180 195

Cycle ** Delicate Express

Amount of food

remains

Light Normal

Cycle sequence

Pre wash 

Main wash (40 °C)

 Rinse  Hot

rinse (60 °C) 

Dry  End

Pre wash (50 °C) 

Main wash (60 °C) 

Hot rinse (60 °C) 

Dry  End

Water consumption

(L)

14.5 10

Energy consumption

(kWh)

0.95 0.9

Cycle time (min.) 130 60

** Delicate : Only for DW6*M505***/DW60M5070IB models

NOTE

The power consumption and cycle time depends on the water temperature and/or load.

WEB_Dishwaser_Global_00_EN.indd 20 2021-04-09  12:01:13

Sidan laddas ...

Samsung DW50R4040BB Användarmanual

Samsung DW50R4040BB Användarmanual

på andra språk

Relaterade papper

Andra dokument