Yamaha DD-7 Bruksanvisning

varumärke: Yamaha

Modell: DD-7

Kategori: Trummor

Typ: Bruksanvisning

Denna manual är också lämplig för

DD-50

DIGITAL

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

DEUTSCHFRANÇAIS

ESPAÑOL

ENGLISH

SPECIAL MESSAGE SECTION

This product utilizes batteries or an external power supply (adaptor). DO

NOT connect this product to any power supply or adaptor other than one

described in the manual, on the name plate, or specifically recommended

by Yamaha.

This product should be used only with the components supplied or; a cart,

rack, or stand that is recommended by Yamaha. If a cart, etc., is used,

please observe all safety markings and instructions that accompany the

accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at the

time of printing. However, Yamaha reserves the right to change or modify

any of the specifications without notice or obligation to update existing

units.

This product, either alone or in combination with an amplifier and head-

phones or speaker/s, may be capable of producing sound levels that could

cause permanent hearing loss. DO NOT operate for long periods of time

at a high volume level or at a level that is uncomfortable. If you experience

any hearing loss or ringing in the ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period before

damage occurs.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a

function or effect works (when the unit is operating as designed) are not

covered by the manufacturer’s warranty, and are therefore the owners

responsibility. Please study this manual carefully and consult your dealer

before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and environ-

mentally friendly. We sincerely believe that our products and the produc-

tion methods used to produce them, meet these goals. In keeping with

both the letter and the spirit of the law, we want you to be aware of the

following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of

battery is approximately five years. When replacement becomes neces-

sary, contact a qualified service representative to perform the replace-

ment.

This product may also use “household” type batteries. Some of these

may be rechargeable. Make sure that the battery being charged is a

rechargeable type and that the charger is intended for the battery being

charged.

When installing batteries, do not mix batteries with new, or with batteries

of a different type. Batteries MUST be installed correctly. Mismatches or

incorrect installation may result in overheating and battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all batter-

ies away from children. Dispose of used batteries promptly and as regu-

lated by the laws in your area. Note: Check with any retailer of household

type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some reason

its useful life is considered to be at an end, please observe all local, state,

and federal regulations that relate to the disposal of products that contain

lead, batteries, plastics, etc. If your dealer is unable to assist you, please

contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model

number, serial number, power requirements, etc., are located on this

plate. You should record the model number, serial number, and the date

of purchase in the spaces provided below and retain this manual as a

permanent record of your purchase.

Model

Serial No.

Purchase Date

92-BP

PLEASE KEEP THIS MANUAL

IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in

this manual, meets FCC requirements. Modifications not expressly ap-

proved by Yamaha may void your authority, granted by the FCC, to use the

product.

IMPORTANT:

When connecting this product to accessories and/or another product use

only high quality shielded cables. Cable/s supplied with this product MUST

be used. Follow all installation instructions. Failure to follow instructions

could void your FCC authorization to use this product in the USA.

NOTE:

This product has been tested and found to comply with the requirements

listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance

with these requirements provides a reasonable level of assurance that your

use of this product in a residential environment will not result in harmful

interference with other electronic devices. This equipment generates/uses

radio frequencies and, if not installed and used according to the instructions

found in the users manual, may cause interference harmful to the operation

of other electronic devices.

Compliance with FCC regulations does not guarantee that interference will

not occur in all installations. If this product is found to be the source of

interference, which can be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of the following meas-

ures:

• Relocate either this product or the device that is being affected by the

interference.

• Utilize power outlets that are on different branch (circuit breaker or fuse)

circuits or install AC line filter/s.

• In the case of radio or TV interference, relocate/reorient the antenna. If

the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-

axial type cable.

If these corrective measures do not produce satisfactory results, please

contact the local retailer authorized to distribute this type of product. If you

can not locate the appropriate retailer, please contact Yamaha Corporation

of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena

Park, CA90620

• This applies only to products distributed by Yamaha Corporation of

America.

FCC INFORMATION (U.S.A.)

The serial number of this product may be found on the bottom

of the unit. You should note this serial number in the space

provided below and retain this manual as a permanent record of

your purchase to aid identification in the event of theft.

Model No. DD-50

Serial No.

Entsorgung leerer Batterien

(nur innerhalb Deutschlands)

Leisten Sie einen Beitrag zum Umweltschutz. Verbrauchte

Batterien oder Akkumulatoren dürfen nicht in den Hausmüll. Sie

können bei einer Sammelstelle für Altbatterien bzw. Sondermüll

abgegeben werden. Informieren Sie sich bei Ihrer Kommune.

Congratulations!

Thank you for purchasing the Yamaha DD-50. The DD-50 has been developed to

act and play like a drum set but with greater ease. Before you use the instru-

ment, we recommend you to read through this manual.

Your DD-50 will give you years of playing pleasure if you follow the simple rules given below:

YAMAHA is not responsible for damage caused by improper handling or operation.

Taking Care of Your DD-50

■ Location

Do not expose the instrument to the following

conditions to avoid deformation, discoloration, or

more serious damage.

● Direct sunlight (e.g. near a window).

● High temperatures (e.g. near a heat source,

outside, or in a car during the daytime).

● Excessive humidity.

● Excessive dust.

● Strong vibration.

■ Power Supply

● Turn the power switch OFF when the instru-

ment is not in use.

● An AC adaptor, if used (the DD-50 runs from

either batteries or an optional AC adaptor),

should be unplugged from the AC outlet if

the instrument is not to be used for an ex-

tended period of time.

● Unplug the AC adaptor during electric

storms.

● Avoid plugging the AC adaptor into the same

AC outlet as appliances with high power

consumption, such as electric heaters or

ovens. Also avoid using multi-plug adaptors

since these can result in reduced sound

quality, operation errors, and possibly dam-

age.

■ Turn Power OFF When Making

Connections

● To avoid damage to the instrument and other

devices to which it is connected, turn the

power switches of all related devices OFF

prior to connecting or disconnecting cables.

■ Handling and Transport

● Never apply excessive force to the controls,

connectors or other parts of the instrument.

● Always unplug cables by gripping the plug

firmly, not by pulling on the cable.

● Disconnect all cables before moving the

instrument.

● Physical shocks caused by dropping, bump-

ing, or placing heavy objects on the instru-

ment can result in scratches and more serious

damage.

■ Cleaning

● Clean the cabinet and panel with a dry soft

cloth.

● A slightly damp cloth may be used to remove

stubborn grime and dirt.

● Never use cleaners such as alcohol or thinner.

● Avoid placing vinyl objects on top of the

instrument (vinyl can stick to and discolor the

surface).

■ Electrical Interference

● This instrument contains digital circuitry and

may cause interference if placed too close to

radio or television receivers. If this occurs,

move the instrument further away from the

affected equipment.

■ Data Backup

● Custom data and some settings (see page 21)

will be retained in memory even if the power

switch is turned OFF as long as an AC power

adaptor is connected or batteries are installed.

■ Service and Modification

● The DD-50 contains no user serviceable parts.

Opening it or tampering with it in anyway can

lead to irreparable damage and possibly

electric shock. Refer all servicing to qualified

YAMAHA personnel.

Table of Contents

Setting up the DD-50 3

Power Supply ................................................3

When Using headphones

(About the PHONES/AUX OUT jack)............3

Control Panel 4

Connecting the foot pedals 1/2 ..................... 5

Supplied Accessories ...................................5

Playing the Demo Song 6

● MASTER VOLUME.......................................6

● SONG VOLUME...........................................6

Play the Pads/Pedals 7

Pad Names ................................................... 7

Assigning a Drum Kit to the

Pads and Pedals ...........................................8

Assigning a Voice to Individual

Pads and Pedals (“CU” Custom Kit) .............8

REVERB ON/OFF ........................................9

● Select the REVERB Depth ............................9

CLICK ON/OFF.............................................9

Try Recording 15

RECORD .................................................... 15

Playback .....................................................15

Using the MIDI/Utility Mode 16

Data 23

Drum Voice List ........................................... 23

Drum Kit List ...............................................24

Song List..................................................... 26

Drum Map ...................................................27

Specifications..............................................28

MIDI Implementation Chart......................... 29

What is MIDI? ............................................. 16

What you can do with MIDI......................... 16

Enter/Exit the MIDI/Utility Mode.................. 17

Setting the Clock.........................................17

Local ON/OFF.............................................18

Setting the MIDI Transmit Channel ............. 18

Setting the MIDI Note Number.................... 20

Initialize 21

Troubleshooting 22

● Data Backup .............................................. 21

Playing a SONG 10

Selecting a SONG ......................................10

Auto Kit Select ON/OFF Setting..................10

Adjusting the TEMPO .................................11

Play along with a SONG 12

TRACK ON/OFF ......................................... 12

TAP START .................................................12

BREAK........................................................13

A-B REPEAT ...............................................14

● Cancel the Repeat Points ............................ 14

Power Supply

Your DD-50 will run either from batteries or an optional power adaptor. Follow the instructions below

according to the power source you intend to use.

Setting up the DD-50

Using an AC-Adaptor (sold separately)

Installing Batteries

Connect the optional power adaptor (Yamaha

PA-3 or PA-3B) to the DC IN 10-12V jack located

on the unit’s left side panel, and plug the AC power

adaptor into an AC power outlet.

Close the battery compartment cover securely.

Open the battery compartment cover on the

underside of the DD-50.

Insert six “C” size, R14, SUM-2 or equivalent

batteries. When inserting the batteries, be

careful to follow the polarity markings in the

illustration.

• Do not attempt to use an AC adaptor other than the

PA-3 or PA-3B. Use of an incompatible adaptor may

result in the instrument becoming hot or, irreparable

damage to the DD-50. It may also result in fire. If the

instrument is damaged due to use of an incompatible

adaptor, YAMAHA is not responsible for the damage.

When Using Headphones

(About the PHONES/AUX OUT Jack)

An optional set of stereo headphones (such as

the Yamaha HPE-150 or HPE-3) can be connected

to the PHONES/AUX OUT jack located on the

side panel. When a pair of headphones is con-

nected to the jack, the DD-50’s internal speakers

will switch off automatically, perfect for private

practice or late night playing. If you want to use an

external sound system, the headphone jack can

also be used to connect the DD-50 to a stereo

system or mixing console. (Use a standard plug n

pin plug adaptor to connect the DD-50 to a stereo

system.)

* Turn the power OFF on all equipment before

making any connections.

• Power will be automatically drawn from the AC

adaptor if an optional AC adaptor is connected while

batteries are installed in the instrument.

• It is recommended that you replace worn batteries as

soon as possible. When battery voltage drops, the

DD-50’s display will dim and/or the sound will become

distorted. When this occurs, replace the batteries with

a complete set of six new batteries of the same type.

• NEVER mix old and new batteries, different types of

batteries (alkaline, magnesium, etc.), batteries by

different makers, or batteries from the same maker

but of different types.

Misuse may cause the instrument to become hot,

result in fire, or battery leakage.

• Also, to prevent damage due to battery leakage,

remove all of the batteries from the instrument when it

is not to be used for an extended period of time.

Batteries left in an unused instrument will also loose

their power over time.

AC power socket

PA-3/

PA-3B

DC IN 10 - 12V

Control Panel

(

! CLICK button .................................................9

@ DIAL...............................................................8

# START/STOP button....................................10

$ BREAK/TAP START button....................12, 13

% A-B REPEAT button.....................................14

^ DEMO button.................................................6

& Drum Pads (x 7) ............................................7

Front Panel Page

1 POWER ON/OFF Switch...............................6

2 SONG VOLUME buttons ...............................6

3 PAD ASSIGN button ................................8, 19

4 KIT ASSIGN button .................................8, 20

5 SONG button ...............................................10

6 TEMPO button .............................................11

7 Display ...........................................................8

8 MASTER VOLUME buttons...........................6

9 REVERB button.............................................9

0 Track buttons

DRUM 1 button ......................................12, 17

DRUM 2 button ......................................12, 18

BASS button ................................................12

BACKING button....................................11, 12

DC IN 10 - 12V

PHONES /

AUX OUT

BEAT

TEMPOSONG

CLICKBACKINGBASS

DRUM 2DRUM 1

POWER

OFF ON

REVERB

PAD KIT

ASSIGN

PRESET TEMPO

MASTER VOLUME

SONG

VOLUME

Control Panel

)

Side Panel (Left)

* DC IN 10-12V (AC Adaptor) Jack ..................3

( PHONES/AUX OUT Jack ..............................3

Side Panel (Right)

) MIDI IN/MIDI OUT Terminals .......................16

q PEDAL 1/2 Jacks...........................................5

MIDI IN

MIDI OUT

PEDAL 1

PEDAL 2

DEMO DD-50

BREAK/

TAPSTART

START/

STOP

A-B

REPEAT

Connecting the Foot Pedals (1/2)

The supplied foot pedals can be connected to the

DD-50 to similarly play the drum set’s hi-hat

pedal or bass drum voices or they can also be

assigned to play other voices as well.

• Do not press the pedal while connecting

it to the DD-50 or while turning on the

power. (Connecting in this manner with

the power on, the pedal’s function may

be reversed.)

● Supplied Accessories

Foot Pedal x 2

Drum Stick x 2

Owner’s Manual

Playing the Demo Song

1 Turn on the power

Turn the [POWER] switch ON.

To give you idea of the DD-50’s possibilities, it comes with a demonstration song. To playback

the demo song:

POWER

OFF ON

Press the [DEMO] button, the demo song will start playback.

2 Start the Demo Song

MASTER VOLUME

Small Large

SONG

VOLUME

Small Large

● MASTER VOLUME

The overall volume level of the DD-50 is controlled by two [MAS-

TER VOLUME] buttons (10 volume levels L0-L9).

Press the large [MASTER VOLUME] button to increase the

overall volume by one level. Press the small [MASTER VOL-

UME] button to decrease the overall volume one level. Holding

down either of the buttons increases or decreases the volume level

rapidly.

● SONG VOLUME

The song’s volume level is controlled by the two [SONG VOL-

UME] buttons (10 volume levels L0-L9). (Demo Song, Song see

page 10)

The SONG VOLUME can be used to adjust the balance between

the song accompaniment and your own performance on the pads.

Press the large [SONG VOLUME] button to increase the song

volume by one level. Press the small [SONG VOLUME] button to

decrease the song volume by one level. Holding either of the

buttons increases or decreases the song volume level rapidly.

DEMO

L0 < L5 > L9

Small < Volume Level > Large

*When the MASTER VOLUME is set to L0, the song’s volume is silenced.

L0 < L5 > L9

Small < Volume Level > Large

* When the SONG VOLUME is set to L0, the song’s volume is silenced.

3 Stop the Demo Song

To stop playback, press either the [DEMO] button again or the

[START/STOP] button.

BREAK/

TAPSTART

START/

STOP

A-B

REPEAT

REC.

DEMO

Play the Pads/Pedals

Strike the pad with the supplied drum sticks to play the drum voices. Drum Kit “00” is auto-

matically chosen whenever the power is turned on (see the “Drum Kit List” page 24).

Striking the pads with different force results in relatively loud or soft sounds accordingly.

Loudness of the sound may vary according to which part of the pad is struck.

Ex. shown, Drum Kit 00 : Standard 1

Pad 3

18: Mid Tom (High)

Pedal 1

1: Bass Drum (Mid)

Pedal 2

34: Hi-Hat Pedal

A hi-hat sound is assigned to the Small Pad 3

(Drum Kit 00). Striking the Small Pad 3while

pressing on Pedal 2 produces a closed hi-hat

sound. Striking the pad without pressing the pedal

produces an open hi-hat sound.

The bass drum voice is control-

led by pressing Foot Pedal 1.

Use Foot Pedal 2 to control the

Hi-hat. (This is in the case of

Drum Kit 00.)

Small Pad 3

34: Hi-Hat

Close/Open

Pad 4

20: Low Tom (High)

Pad 1

8: Snare Drum (High)

Pad 2

16: High Tom (High)

Small Pad 1

38: Crash

Cymbal (High)

Small Pad 2

39: Ride Cymbal

Pad Names

Assigning a Drum Kit to the Pads and Pedals

Play the Pads/Pedals

The DD-50 allows you to choose from 20 different Drum Kits (00-19 : see the “Drum Kit List”

page 24) quickly and easily. 20 of the kits have preset voice combinations that will be set to the pads

and pedals when the kit is selected. Select some different kits and try playing them.

The DD-50 also has one Custom Drum Kit allowing you to assign the desired voices to the seven

pads or two pedals (see “Assigning a Voice to Individual Pads and Pedals” below).

1 Press the [KIT ASSIGN] button

BEAT

ASSIGN

PAD KIT

2 Select a Drum Kit Number

Turn the DIAL to select a Drum Kit number. Drum Kit numbers will

increase as the DIAL is turned to the right (clockwise), and decrease as

the DIAL is turned to the left (counter-clockwise).

• Drum Kit number 00 is normally selected when the power is turned ON. How-

ever, if Auto Kit Select is set to OFF, the last Drum Kit selected before turning the

power OFF, is automatically selected when the power is turned ON. (See “Auto

Kit Select ON/OFF Setting” on page 11)

• The “CU” Drum Kit is the Custom Kit. Changes made to any one of the preset

drum kits will be saved here. (See “Assigning a Voice to Individual Pads and

Pedals” below.)

Assigning a Voice to Individual Pads and Pedals

(“CU” Custom Kit)

The DD-50 contains a total of 75 high quality drum sounds (see the “Drum Voice List” page 23)

that can be assigned to each of the 7 drum pads and 2 foot pedals. Try assigning some different voices

to the “CU” Custom Drum Kit.

• Any change made to one of the preset drum kits will automatically be saved in the

“CU” Custom Drum Kit.

• Both the Custom and “00” drum kit contents are the same until modified (see the

“Drum Kit List” page 24).

1 Press the [PAD ASSIGN] button

BEAT

ASSIGN

PAD KIT

2 Select a Pad/Pedal

BEAT

00 19 CU

Press the [PAD ASSIGN] button, Pad 1’s currently assigned voice

number is shown in the display.

Strike any pad one time (or press a pedal), that pad’s/pedal’s currently

assigned voice number is shown in the display.

Pressing the [KIT ASSIGN] button, the button’s lamp will light and

the currently selected Drum Kit number appears on the display.

Play the Pads/Pedals

3 Select a Voice Number

You can select the voice by repeatedly striking the pad, repeatedly

pressing the pedal (while listening to the voice) or by turning the DIAL.

●

Striking the pad or pressing the pedal to select a voice.

First, select a pad or pedal by striking or pressing it once. After the

pad/pedal has been selected, every time the pad is struck or a pedal

is pressed, voice numbers will increase by a value of one (1).

● Using the DIAL to select a voice.

Turn the DIAL to the right (clockwise), and voice numbers will

increase. Turn the DIAL to the left (counter-clockwise), and voice

numbers will decrease.

4 Play the Pads and Pedals

After assigning a voice to the desired pad/pedal, press the [SONG]

button. You can now play the voice you have assigned to the pad/pedal.

Repeat the previous steps for any or all of the DD-50’s pads and pedals

and try playing your own original drum kit.

PRESET TEMPO

SONG TEMPO

REVERB ON/OFF

Different depths of the DD-50’s reverb effect can be selected to add to

the DD-50’s overall sound.

To turn on the reverb effect, press the [REVERB] button. To turn off

the reverb effect, press the [REVERB] button again.

● Select the REVERB Depth

When the reverb has been turned on, press and hold the [REVERB]

button, turn the DIAL to select one of the three reverb depths that

appear in the display. [r1], [r2], [r3].

Selecting [r3] adds the most reverb depth to the effect.

REVERB

BEAT

0 1 ........... ........... ...........73 74

CLICK ON/OFF

The DD-50’s CLICK feature produces a metronome click to make the

tempo easier to follow and improve your timing while playing the pads.

To hear the metronome click, press the [CLICK] button. To turn the

click off, press the button once again.

CLICK

• REVERB Depth data is not transmitted or received via MIDI.

Playing a SONG

The DD-50 features 100 different songs that can be used to provide accompaniment (see the

“Song List” page 26). Select one of the songs and have a listen.

Selecting a SONG

1 Press the [SONG] button

Press the [SONG] button, its LED indicator will light, and the cur-

rently selected song number will appear in the display.

2 Use the DIAL to select a song number

Song numbers will increase in value as the DIAL is turned to the right

(clockwise) and decrease as the DIAL is turned to the left (counter-

clockwise). (See the “Song List” on page 26)

• Song number “00” is automatically selected whenever the power is turned ON.

• With the Auto Kit Select turned on, selecting a song will also automatically select

the best suited Drum Kit for that song (see “Auto Kit Select ON/OFF Setting”

below).

• Song numbers are arranged according to their complexity. Smaller numbers are

easier to play than larger numbers.

PRESET TEMPO

SONG TEMPO

BEAT

3 Press the [START/STOP] button

Press the [START/STOP] button, after a two-measure count-in (or one

measure count-in), the song will start playback.

As the song is playing, the Song’s current measure will be shown in the

display. Try playing the pads and pedals along with the song.

To stop playback of the song, press the

[START/STOP]

button once

again.

• You can also use the TAP START function to start songs (see page 12).

BREAK/

TAPSTART

START/

STOP

A-B

REPEAT

REC.

The DD-50’s songs consists of two types, loop type and sequence

type (see the “Song List” page 26).

Sequence type songs will automatically stop when the song reaches its

end.

Loop type songs will continuously play from the time the [START/

STOP] button is initially pressed, until the button is pressed once again.

Auto Kit Select ON/OFF Setting

1 Setting the Auto Kit Select to ON or OFF

Press the [DEMO] and [START/STOP] buttons simultaneously to

enter the MIDI/Utility Mode .

The Auto Kit Select function automatically selects the best matching drum kit to the selected song.

You can deactivate this feature by setting the Auto Kit Select to OFF.

Sequence

Loop

00 01 . . ...99 CU

2 Select ON or OFF

Press the [BACKING] button and the current ON/OFF setting will

appear in the display. Turn the DIAL to the right (clockwise) to activate

the Auto Kit Select (on). Turn to the left (counter-clockwise) to deactivate

the Auto Kit Select (oF).

Playing a SONG

Adjusting the TEMPO

1 Press the [TEMPO] button

2 Set the Tempo

The song tempo can be set anywhere from 40 to 280 beats per minute. As tempo numbers increase,

the tempo will become faster.

Press the [TEMPO] button, the current tempo value (40-280) appears

in the display.

Use the DIAL to select the TEMPO. Turn the DIAL to the right

(clockwise) to increase Tempo values, turn to the left (counter-clockwise)

to decrease Tempo values.

(Tempo values will cycle to 40 or 280 then stop.)

PRESET TEMPO

SONG TEMPO

BEAT

3 Exit the Tempo setting mode

Press the [SONG] button to exit from the Tempo setting mode.

• When both the SONG and TEMPO buttons are pressed simultaneously, the

preset tempo of the currently selected song will automatically applied.

PRESET TEMPO

SONG TEMPO

BEAT

Tempo Display Comment

q=90 90 —

q=110 ,10 100th digit (1) is shown as a single dot

q=250 ,5,0 100th digit (2) is shown as two dots

1st beat 2nd beat 3rd beat 4th beat

,9,0 9,0 9,0 9,0

● About the Beat Indicator

During song playback, the two beat lamps in the display will flash

in a specific pattern to assist you in keeping the beat.

q= 90 beats per minute.

BEAT

BACKING

BEAT

3 Exit the Auto Kit Select

• The Auto Kit Select is automatically set to “OFF” when the MIDI Transmit Note is

changed to another channel.

Press the [DEMO] and [START/STOP] buttons simultaneously once

again to exit the MIDI/Utility Mode .

40 41 ,,7,9 ,8,0

Play along with a SONG

TRACK ON/OFF

Use the pads and pedals to play along with a song accompaniment.

The DD-50’s song accompaniment consists of 4 tracks; Drum 1/2, Bass, and Backing tracks.

• The DD-50 can play a total of 28 notes simultaneously. That includes notes

produced by song accompaniment, pads, foot pedals, and note data received

through the MIDI IN jack.

Pressing a Track button ([DRUM 1], [DRUM 2], [BASS], [BACK-

ING]) will mute (turn off the sound) the corresponding track and its

indicator lamp will turn off.

Muting DRUM 1 and DRUM 2 tracks allows you to practice your

playing technique in Karaoke style (Minus One).

DRUM 1 Main Drum track

DRUM 2 Main Percussion track

BASS Bass track

BACKING Main Backing Track

DRUM 1 DRUM 2 BASS BACKING

TAP START

The TAP START function allows you to set the song’s overall tempo as well as start the accompani-

ment. The accompaniment will playback at the tempo with which the pads are struck or the pedals are

pressed.

1 Press the [BREAK/TAP START] button

Press the [BREAK/TAP START] button when the song stops, its

indicator will flash and the DD-50 is in Tap Start standby mode.

To cancel the Tap Start mode, simply press the [BREAK/TAP

START] button once again (the indicator will turn off).

2 Tap Start

In the case of a song in 4/4, strike any pad or press any pedal four

times, the accompaniment will start at the desired tempo.

• The number of times needed to strike the pad will change according to the

following time signatures; 5/4, 5 times; 4/4, 4 times; 3/4, 3 times; 6/8, 2 times.

3 Stop the Song Playback

To stop playback, press the [START/STOP] button.

BREAK/

TAPSTART

START/

STOP

A-B

REPEAT

REC.

BREAK/

TAPSTART

START/

STOP

A-B

REPEAT

REC.

BREAK

During song playback, press the BREAK/TAP START button

With the BREAK function, you can liven up songs by adding your own solos or fills, whenever you

want. Striking a pad while in the BREAK mode, the song’s accompaniment will be muted until the end

of the measure you have finished your fill or solo in.

During song playback, press the [BREAK/TAP START] button, its

indicator will flash and the DD-50 is in BREAK standby mode.

To cancel the Break mode, simply press the [BREAK/TAP START]

button once again (its indicator will turn off).

Play along with a SONG

BREAK/

TAPSTART

START/

STOP

A-B

REPEAT

REC.

3 Exit the BREAK mode

The DD-50 returns to the BREAK standby mode when the BREAK

measure is completed.

To exit the BREAK mode, press the [BREAK/TAP START] button.

The BREAK mode is also exited when the song is stopped.

BREAK/

TAPSTART

START/

STOP

A-B

REPEAT

REC.

2 Break

Strike any pad and the accompaniment will mute until the end of the

measure you played in. You can play a drum fill or drum solo during this

break.

A-B REPEAT

1 To set the “A” (start repeat) point

3 Stop the A-B REPEAT mode

When the song playback has reached the start of the section you want

to practice, press the [A-B REPEAT] button and the “A” repeat point is

set. An “A” will appear in the display.

If you want to practice a particular section of a song, you can specify that section’s “A” (start

repeat) and “B” (end repeat) points. The accompaniment will continuously repeat between points

“A” and “B” allowing you to practice between those points for as long as you like.

Press the [START/STOP] button and the song accompaniment will stop.

“Ab” will appear in the display indicating the A-B REPEAT mode is

still engaged.

Press the [START/STOP] button once again and the accompaniment

will again repeat between the set points.

Play along with a SONG

2 To set the “B” (end repeat) point

BEAT

BREAK/

TAPSTART

START/

STOP

A-B

REPEAT

REC.

BREAK/

TAPSTART

START/

STOP

A-B

REPEAT

REC.

BEAT

BREAK/

TAPSTART

START/

STOP

A-B

REPEAT

REC.

● Cancel the Repeat Points

To cancel the A-B REPEAT, press the [A-B REPEAT] button

during playback or while playback is stopped, the A-B REPEAT

mode will be canceled (the A-B REPEAT points will also be

canceled) and normal playback of the accompaniment will con-

tinue.

When the song playback has reached the end point of the section you

want to practice, press the [A-B REPEAT] button once again and the A

to B repeat points are set, “b” appears in the display. “Ab” will appear in

the display and after a one measure count-in the repeat playback will

start. The current measure number will appear in the display during the

repeat playback.

• The A-B REPEAT start and end points can only be set in measure steps.

• Songs consist of two types; loop type and sequence type (see the “Song List” on

page 26). When setting the A-B points for sequence songs, set both points

before the end of the song. The set “A” point will be canceled if the “B” point is

not set before the end of the song.

BREAK/

TAPSTART

START/

STOP

A-B

REPEAT

REC.

• Selecting another song will cancel any previously set A-B REPEAT points.

• In the case of a loop type song, it is possible, for example, to set the “A” point at

measure 10 and set the “B” point at measure 3 (after the song has looped back

to the beginning).

Try Recording

Playback

The DD-50’s Custom Song feature (song number “CU”) allows you to record and playback

one original song (600 notes approximately).

The recorded Custom Song (song number “CU”) can be played back in the same manner as any

song (song numbers “00”-”99”).

BEAT

Song number “CU” follows Song number “99” (or prior to “00”).

• The A-B REPEAT mode (see 14 page) cannot be used in the Custom Song Mode.

RECORD

1 Prepare to Record

Select the desired song, drum kit, tempo, track on/off setting, and

reverb settings.

2 Start Recording

ress both the [START/STOP] and [BREAK/TAP START] buttons

simultaneously, after a count-in (the indicator will flash) recording will start.

• Data will not be recorded during the 2 measure count-in.

• Press the BREAK/TAP START button during the 2 measure count-in to enter Tap

Start Record Standby mode (see page 12).

• Press the CLICK button to cancel the metronome during recording.

3 Stop Recording

To stop recording, press the [START/STOP] button.

• Any previously recorded data will be replaced with new data.

• If the memory becomes full while recording is in progress, “FL” will appear in the

display and recording will automatically stop.

BREAK/

TAPSTART

START/

STOP

A-B

REPEAT

REC.

* MIDI data cannot be recorded to the memory.

BEAT

BREAK/

TAPSTART

START/

STOP

A-B

REPEAT

REC.

● Data that can be recorded in the Custom Song Mode.

• Drum pad and pedal data.

• Song data (the number cannot be changed while in the RECORD Mode).

• Track ON/OFF settings.

• Tempo setting (The tempo cannot be changed while in the RECORD mode).

• Song Volume setting.

• Reverb ON/OFF setting.

• Break ON/OFF setting.

Using the MIDI/Utility Mode

The MIDI IN and MIDI OUT terminals, located on the DD-50’s right side panel, offer broad-

ened musical possibilities through use of MIDI. But, what is MIDI? What can you do with

MIDI? How can you use MIDI with the DD-50? Here are a few examples.

MIDI Keyboard’s

MIDI IN

MIDI OUT

DD-50

What you can do with MIDI

What is MIDI?

MIDI stands for Musical Instrument Digital Interface. MIDI is a world wide standard that

makes it possible for various electronic musical instruments and other devices, such as computers, to

“communicate” with each other. For example, by connecting a MIDI tone generator to the DD-50’s

MIDI OUT terminal, you can play the tone generator’s voices from the DD-50’s pads and pedals.

The DD-50 is equipped with two types of MIDI terminals, both are

located on the right side panel.

● MIDI IN

Data transmitted from other MIDI instruments via MIDI, is re-

ceived at this terminal.

● MIDI OUT

Data produced by the DD-50, is transmitted to other MIDI instru-

ments via MIDI from this terminal.

• Use a MIDI cable (option), obtainable at your local music dealer, when making

MIDI connections.

• Never use MIDI cables longer than 15 meters in length. (Cables longer than 15

meters can pick up “noise” which can cause data errors.)

● Connect the DD-50’s MIDI OUT jack to a MIDI keyboard’s

(or tone generator’s) MIDI IN jack.

This setup allows you to use the DD-50’s pads to control another

MIDI instrument. Playing the DD-50’s pads will result in the other

MIDI instrument’s voice sounding simultaneously, creating a

thicker overall sound.

● Connect the DD-50’s MIDI OUT jack to a MIDI sequenc-

er’s MIDI IN terminal.

Data produced by the DD-50 (Key ON and Velocity data) can be

recorded to a MIDI sequencer. Data can also be recorded to com-

puters or other sequencers as well.

● Connect the DD-50’s MIDI IN terminal to a MIDI key-

board’s MIDI OUT terminal.

In this setup the DD-50 can be used as a tone generator and its

voices can be played from a MIDI keyboard. Using a keyboard as a

controller, it is possible to play DD-50 voices that are not assigned

to the pads/pedals.

● Connect the DD-50’s MIDI IN terminal to a MIDI sequenc-

er’s MIDI OUT terminal.

The sequencer’s data can be used to drive the DD-50’s sounds.

MIDI OUT

MIDI IN

MIDI Keyboard

MIDI IN

MIDI OUT

DD-50

MIDI IN

MIDI OUT

DD-50

Sequencer

MIDI IN

MIDI OUT

DD-50

Yamaha

MIDI Data Filer

MDF2 etc.

Enter/Exit the MIDI/Utility Mode

To enter the MIDI mode, press the [START/STOP] and [DEMO]

buttons simultaneously, an “

” will appear in the display to indicate the

MIDI mode.

Setting the Clock

Connecting the DD-50, by MIDI cable, to an external MIDI device, such as a sequencer, time based

functions (song playback, etc.) must be controlled by the internal clock (I) or an external clock (E).

When the internal clock (I) is enabled, timing will be controlled by the DD-50’s internal clock. When

an external clock (E) selected, time based functions will be controlled by the sequencer’s or compu-

ter’s clock.

1 Display the clock setting

After entering the MIDI/Utility mode, press the [DRUM 1] button to

see the current setting for the MIDI clock.

2 Set the Clock to External or Internal

To set the clock to “E” (external), turn the DIAL to the right (clock-

wise). To set the clock to “I” (internal), turn the DIAL to the left (counter-

clockwise).

3 Exit the MIDI/Utility mode

After the clock is set, exit the MIDI/Utility mode.

• The default MIDI clock setting is “I” (internal).

Using the MIDI/Utility Mode

DEMO

BREAK/

TAPSTART

START/

STOP

A-B

REPEAT

REC.

BEAT

DRUM 1

BEAT

● I (Internal)

The DD-50’s clock is used as the timing clock.

● E (External)

The external clock is used as the timing clock (If the clock is set to

external without being connected to another MIDI device, the DD-

50’s Song Play or Demo functions will not respond).

To exit the MIDI mode, once again press the [START/STOP] and

[DEMO] buttons simultaneously, the MIDI mode will be exited and the

DD-50 will return to its normal play mode.

• Pads and pedals do not sound while in the MIDI/Utility mode.

Local ON/OFF

Setting the Local ON/OFF determines whether or not the internal voices respond to the notes you

play on the DD-50’s pads. Setting this to OFF disconnects the DD-50’s pads from the voices. How-

ever, data produced by the DD-50 is transmitted via the MIDI OUT terminal.

1 Display the Local On/Off Setting

After entering the MIDI/Utility mode, press the [DRUM 2] button and

the current Local ON /OFF setting will appear in the display.

2 Set the Local On/Off

To set to “on” (Local ON), turn the DIAL to the right (clockwise), to

set to “oF”(Local OFF), turn the DIAL to the left (counter-clockwise).

3 Exit the MIDI/Utility mode

After setting the Local ON/OFF, exit the MIDI/Utility mode.

• Regardless of the Local ON/OFF setting, the DD-50’s performance data

(including demo song data) is always sent to the MIDI OUT terminals for

transmission to external MIDI devices.

• The default Local ON/OFF setting is ON (Local ON).

Using the MIDI/Utility Mode

BEAT

DRUM 2

● on (Local ON)

The internal voices will be played and controlled by the DD-50 and

its pads. Data received via MIDI will also be played by the DD-50.

● oF (Local OFF)

Striking the pads will not produce any sound from the voices.

However, data received via MIDI will be played by the DD-50.

Setting the MIDI Transmit Channel

Each of the pads/pedals (a total of 9) can be assigned to transmit on any of the 16 MIDI channels,

or turned off (indicated as “oF” in the display). Also, song transmit channels are as shown below:

Transmit Channel Default

Pad/Pedal 1-16 10

Drum (Song) 9, 10 9

Bass (Song) 11 (fixed) —

Backing (Song) 12-15 (fixed) —

Pad/Pedal

10, 16 16

(Custom Song)

Sidan laddas ...

Yamaha DD-7 Bruksanvisning

varumärke: Yamaha

Modell: DD-7

Kategori: Trummor

Typ: Bruksanvisning

Denna manual är också lämplig för

DD-50

Ladda ner pdf

Rapportera

på andra språk

italiano: Yamaha DD-7 Manuale del proprietario
čeština: Yamaha DD-7 Návod k obsluze
español: Yamaha DD-7 El manual del propietario
Deutsch: Yamaha DD-7 Bedienungsanleitung
polski: Yamaha DD-7 Instrukcja obsługi
português: Yamaha DD-7 Manual do proprietário
français: Yamaha DD-7 Le manuel du propriétaire
Türkçe: Yamaha DD-7 El kitabı
English: Yamaha DD-7 Owner's manual
dansk: Yamaha DD-7 Brugervejledning
русский: Yamaha DD-7 Инструкция по применению
suomi: Yamaha DD-7 Omistajan opas
Nederlands: Yamaha DD-7 de handleiding
română: Yamaha DD-7 Manualul proprietarului

Yamaha DD-7 Bruksanvisning

Denna manual är också lämplig för

Yamaha DD-7 Bruksanvisning

på andra språk

Relaterade papper