Yamaha V1 Bruksanvisning

Kategori
Ljudutjämnare
Typ
Bruksanvisning

Denna manual är också lämplig för

Studio Manager
for
V1.1
Owner’s Manual
E
i
Studio Manager for DM2000 V1.1—Owner’s Manual
Important Information
Exclusion of Certain Liability
Manufacturer, importer, or dealer shall not be liable for any incidental damages including
personal injury or any other damages caused by improper use or operation of Studio Man-
ager for DM2000.
Yamaha makes no representations or warranties with regard to the use of the software and
documentation and cannot be held responsible for the results of the use of this manual and
the software.
Trademarks
Macintosh is a registered trademark of Apple Computer, Inc. Windows is a registered trade-
mark of Microsoft Corporation. OMS is a registered trademark of Opcode Systems, Inc. All
other trademarks are the property of their respective holders and are hereby acknowledged.
Copyright
No part of the Studio Manager for DM2000 software or its documentation may be repro-
duced or distributed in any form or by any means without the prior written authorization
of Yamaha Corporation.
© 2002 Yamaha Corporation. All rights reserved.
Yamaha Web Site
Information about Studio Manager for DM2000, related products, and other Yamaha pro-
fessional audio equipment is available on the Yamaha Professional Audio Web site at:
<http://www.yamaha.co.jp/product/proaudio/homeenglish/navi/index.htm>.
Specifications and external appearance subject to change without notice.
ii
Studio Manager for DM2000 V1.1—Owner’s Manual
Contents
1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Starting Studio Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Quitting Studio Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Configuring Studio Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Synchronizing Studio Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Working with Sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Console Window . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Master Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Output Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3 Selected Channel Window . . . . . . . . . . . . . . . . . . 10
Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Bus Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Aux Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Matrix Sends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Stereo Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Remote Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4 Library Window . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5 Patch Editor Window . . . . . . . . . . . . . . . . . . . . . . 22
Input Patch Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Output Patch Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Insert Patch Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Effect Patch Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Direct Out Patch Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6 Surround Editor Window . . . . . . . . . . . . . . . . . . . 27
7 Effect Editor Window . . . . . . . . . . . . . . . . . . . . . . 28
8 GEQ Editor Window . . . . . . . . . . . . . . . . . . . . . . . 29
9 Timecode Counter Window . . . . . . . . . . . . . . . . . 30
10 Keyboard Shortcuts . . . . . . . . . . . . . . . . . . . . . . . . 31
File Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Windows Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
1 Chapter 1—Getting Started
Studio Manager for DM2000 V1.1—Owner’s Manual
1 Getting Started
Starting Studio Manager
Windows: Click the Start button and then click Programs–>YAMAHA Studio Manager for
DM2000–>Studio Manager for DM2000.
Macintosh: Open the Studio Manager for DM2000 folder and double-click “SM_DM2K.
If a DM2000 is detected while Studio Manager starts up, the Synchronization dialog box
appears, from which you can choose to transfer the settings of the DM2000 to Studio Man-
ager or vice versa. See “Synchronizing Studio Manager” on page 3 for more information. If
no DM2000 is detected, a new Console window opens.
The ONLINE indicator is displayed while Studio Manager is connected to a
DM2000. When no DM2000 is detected, the OFFLINE indicator is displayed.
Quitting Studio Manager
Choose Exit (Quit on the Macintosh) from the File menu.
If there are no unsaved changes, all windows close and Studio Manager quits. If there are
unsaved changes, a message asking if you want to save the changes appears. Click Yes to save
the changes and quit, click No to quit, or click Cancel to cancel the operation. Studio Man-
ager can also be quit by clicking the Console window’s Close button.
Configuring Studio Manager
Selecting Ports
In order to use Studio Manager, you must specify the input and output ports that Studio
Manager should use to communicate with the DM2000.
Windows: Choose System Setup from the File menu, and specify the input and output ports
on the Setup dialog box, as shown below.
Macintosh: Choose Select OMS Ports from the File menu, and specify the input and output
ports (device names set in OMS Studio Setup) on the Setup dialog box, as shown below.
OMS Studio Setup can be opened directly from Studio Manager by selecting OMS Studio
Setup from the File menu.
Note: This version of Studio Manager supports DM2000 System Software V1.10 or later. If used
with an earlier version, some functions (e.g., the Library Undo function) may not work properly.
Note: Choose OMS MIDI Setup from the File menu, and make sure that the “Run MIDI in
Background” option is on.
Configuring Studio Manager 2
Studio Manager for DM2000 V1.1—Owner’s Manual
System Setup
To open the Setup window, choose System Setup from the File menu.
This is the Windows Setup window.
This is the Macintosh Setup window
Input Port/Output Port: (Windows only) These pop-up menus are used to select the
ports with which Studio Manager communicates with the DM2000.
Console Device ID: Studio Manager can control any one of up to eight DM2000s, each
with its own exclusive ID. Select the ID of the DM2000 that you want to control.
Channel Select: These options determine whether or not channel selection is linked.
When the PC–>Console option is on, selecting a channel on Studio Manager selects the
same channel on the DM2000. When the Console–>PC option is on, selecting a channel on
the DM2000 selects the same channel on Studio Manager.
Confirmation: These options determine whether or not a confirmation dialog box
appears when storing, recalling, or patching.
Layer Select: These options determine whether or not Layer selection is linked. When the
PC–>Console option is on, selecting a Layer on Studio Manager selects the same Layer on
the DM2000. When the Console–>PC option is on, selecting a Layer on the DM2000 selects
the same Layer on Studio Manager.
3 Chapter 1—Getting Started
Studio Manager for DM2000 V1.1—Owner’s Manual
Synchronizing Studio Manager
If a DM2000 is detected while Studio Manager starts up, or while Studio Manager is up and
running, the Synchronization dialog box shown below appears.
All Lib: This option determines whether or not Scene and Library data is synchronized.
Console–>PC: Click this button to transfer the settings of the DM2000 to the current Stu-
dio Manager Session.
PC–>Console: Click this button to transfer the settings of current Studio Manager Ses-
sion to the DM2000.
Cancel: Click this button to leave the DM2000 and current Studio Manager Session
unsynchronized.
You can resynchronize the system at any time by choosing Re-synchronize from the Syn-
chronization menu.
Working with Sessions
A Studio Manager Session consists of all DM2000 mix settings, including Scene and library
data.
To create a new Session, choose New Session from the File menu.
To open a previously saved Session, choose Open Session from the File menu.
To save the current Session, choose Save Session from the File menu.
To save the current Session with a new name, choose Save Session as from the File menu.
Only one Session can be open at a time, so when you create a new Session, or open a previ-
ously saved Session, the message This operation will purge the current session appears. If
there are no unsaved changes, or you do not want to save, click OK. If Studio Manager is
offline, the Session is loaded. If Studio Manager is online, the Session is loaded and the syn-
chronization dialog box appears.
Note: Do not operate the DM2000 while synchronization is in progress.
Note: In order to save the current Automix, or the settings of an optional Y56K card, in a Ses-
sion, you must resynchronize Studio Manager beforehand (Console–>PC).
Note: In order to protect the communication port used by Studio Manager, DM2000 commu-
nication settings (e.g., MIDI, Remote Layer, Machine Control) are not affected by PC–>Con-
sole synchronization operations.
Console Window 4
Studio Manager for DM2000 V1.1—Owner’s Manual
2 Console Window
Studio Manager’s Console window displays 24 channel strips and a master section. When
an Input Channel Layer is selected, 24 Input Channels are displayed. When the Master Layer
is selected, the Bus Out, Aux Send, and Matrix Send channels are displayed. And when a
Remote layer is selected, Remote Channels are displayed.
Many functions can be operated from here by clicking and dragging the various controls
and parameters. This is explained in the following sections.
Channels can be viewed in more detail on the Selected Channel window. See page 10 for
more information.
5 Chapter 2—Console Window
Studio Manager for DM2000 V1.1—Owner’s Manual
Input Channels
A SOURCE parameter
This parameter is used to select an Input source. To select an
Input source, click the parameter and choose from the list that
appears.
B Routing buttons
These buttons are used to route the Input Channel to the Bus
Outs.
C STEREO button
This button is used to route the Input Channel’s signal to the
Stereo Out.
D DIRECT button
This button turns on and off the Input Channel’s routing to its
Direct Out.
E Direct Out parameter
This parameter is used to select the Direct Out destination. To
select a destination, click the parameter and choose from the list
that appears.
F PHASE button
This button is used to reverse the signal phase of the channel.
G INSERT button
This button is used to turn on and off the Input Channel’s
Insert.
H GATE button
This button is used to turn on and off the Input Channel’s Gate.
I Gate open/close indicators
These indicators display whether the Gate is open (green) or
closed (red).
J Gate threshold
This displays the Gate Threshold, which can be set by dragging.
K COMP button
This button is used to turn on and off the Input Channel’s Com-
pressor.
L Compressor curve
This display shows the Compressor’s curve.
M EQ button
This button is used to turn on and off the Input Channel’s EQ.
N EQ curve
This display shows the Equalizer’s curve, which can be set by
dragging.
O DELAY button
This button is used to turn on and off the Input Channel’s Delay
function.
B
C
D
6
7
9
K
J
L
M
N
O
P
Q
R
W
X
Y
Z
8
5
a
b
1
T
V
U
S
Input Channels 6
Studio Manager for DM2000 V1.1—Owner’s Manual
P Delay parameter
This parameter is used to set the delay time of the Delay function. Delay times can be set by
dragging.
Q Channel number
This is the channel number.
R AUX section
These controls are used to set the levels of the Aux Sends. To set an Aux Send level,
drag its bar or click a point along the length of the bar. To turn an Aux Send on or
off, click its number.
The following table shows how the Aux Send controls appear depending on the
Aux Send On/Off and Pre/Post settings. Aux Sends can be set to pre-fader or
post-fader on the Selected Channel window (see “AUX SEND section on
page 11).
S Pan/Aux Send display
This display shows the stereo or surround pan position or, while setting an Aux Send, the
Aux Send level in dB.
T PAN control
This control is used to set the Input Channel’s stereo or surround pan position. When the
PAN CONTROL in the Master Section is set to “STEREO, the Pan control appears as a
rotary control, and when set to “SURR, the control appears as dot on a pan graph. The sur-
round pan position can be set by dragging the dot. If you click on the pan graph while hold-
ing down the Shift key, the pan immediately jumps to the new position.
U LFE control
When 5.1 Surround mode is selected, this control is used to set the surround
LFE Channel level. It appears when the PAN CONTROL in the Master Section
is set to “SURR. To set the LFE level, drag the end of its bar or click a point along
the length of the bar.
V AUTO button
This button displays the Automix status of the Input Channel.
W SELECT button
This button is used to select the Input Channel.
X SOLO button
This button solos the Input Channel. It appears orange while the channel is soloed.
Y ON button
This button turns the Input Channel on and off. It appears orange while the channel is on.
Z Short channel name
This is the channel’s short name. To edit the name, click it and type.
a Channel fader
This is the Input Channel’s fader.
b Channel meter
This meter displays the signal level of the Input Channel.
Aux Send status Appearance
On or off but no level set Dark blue bar
Off, pre-fader Green bar outline displays level
On, pre-fader Green bar displays level
Off, post-fader Orange bar outline displays level
On, post-fader Orange bar displays level
7 Chapter 2—Console Window
Studio Manager for DM2000 V1.1—Owner’s Manual
Master Section
A ONLINE status indicator
This indicator shows whether Studio Manager is online or
offline.
B Meters
These meters display the output level of the Stereo Out when
PAN CONTROL is set to “STEREO, or the Bus Outs used for
surround processing when PAN CONTROL is set to “SURR.
The Meters in 3-1 and 5.1 Surround modes are shown below.
C LAYER buttons
These buttons are used to select the Layers.
D PAN CONTROL
These buttons are used to select either “STEREO” (Stereo mode)
or “SURR (Surround mode). The Pan control on the Input
Channels is a rotary control when “STEREO” is selected, and a
dot on a pan graph when “SURR is selected.
E AUTO button
This button displays the Automix status of the Stereo Out.
F SELECT button
This button is used to select the Stereo Out. If it’s clicked while a
Remote Layer is selected, it will light up, but the Stereo Out will
not appear in the Selected Channel window.
G ON button
This button turns the Stereo Out on and off. It appears orange
while the Stereo Out is on.
H Channel fader
This is the Stereo Out fader.
1
2
3
5
6
7
8
4
3-1 5.1
Output Channels 8
Studio Manager for DM2000 V1.1—Owner’s Manual
Output Channels
When the Master Layer is selected, the Bus Out, Aux Send, and Matrix Send channels are
displayed. A Bus Out channel is shown here. Aux Send and Matrix Send channels appear
the same except that they do not have a STEREO button.
A STEREO button (Bus Out only)
This button is used to route the Bus Out to the Stereo Out.
B INSERT button
This button is used to turn on and off the Bus Out’s Insert.
C COMP button
This button is used to turn on and off the Bus Out’s Compressor.
D Compressor curve
This display shows the Compressor’s curve.
E EQ button
This button is used to turn on and off the Bus Out’s EQ.
F EQ curve
This display shows the Equalizer’s curve, which can be set by
dragging.
G DELAY button
This button is used to turn on and off the Bus Out’s Delay func-
tion.
H Delay parameter
This parameter is used to set the delay time of the Delay func-
tion. Delay times can be set by dragging.
I Channel number
This is the channel number.
J AUTO button
This button displays the Automix status of the Bus Out.
K SELECT button
This button is used to select the Bus Out.
L SOLO button
This button solos the Bus Out. It appears orange while the Bus
Out is soloed.
M ON button
This button turns the Bus Out on and off. It appears orange
while the channel is on.
N Short channel name
This is the channel’s short name. To edit the name, click it and
type.
O Channel fader
This is the Bus Out’s fader.
P Channel meter
This meter displays the signal level of the Bus Out.
6
C
P
N
L
J
O
M
K
I
8
7
5
D
1
2
9 Chapter 2Console Window
Studio Manager for DM2000 V1.1—Owner’s Manual
Remote Channels
When a Remote Layer is selected, Remote Channels are displayed.
A Channel number
This is the channel number.
B SELECT button
This button is used to select the Remote Channel.
C ON button
This button turns the Remote Channel on and off. It appears
orange while the channel is on.
D Short channel name
This is the Remote Channel’s short name. To edit the name, click
it and type.
E Channel fader
This is the Remote Channel’s fader.
Note: When the remote target setting on the DM2000 is set to
anything other than User Defined, the ON buttons and channel
faders have no effect, and the name of the specified target is dis-
played in the channel’s short name.
C
5
D
1
2
Selected Channel Window 10
Studio Manager for DM2000 V1.1—Owner’s Manual
3 Selected Channel Window
The Selected Channel window allows detailed editing of the currently selected channel. To
open the Selected Channel window, choose Selected Channel from the Windows menu.
The layout of the Selected Channel window depends on the currently selected channel.
There are six variations, as follows:
Input Channel (see below)
Bus Out (see page 12)
Aux Send (see page 14)
Matrix Send (see page 16)
Stereo Out (see page 18)
Remote Channel (see page 19)
Input Channels
This is the Selected Channel window for Input Channels.
A CHANNEL SELECT, INPUT PATCH & LIBRARY section
Channels can be selected by clicking the Channel ID and selecting from the list that appears,
or by clicking the left and right Channel Select buttons. The long channel name is displayed
below the Channel ID. To edit the name, click it and type. The INPUT PATCH parameter
is used to select an input source. To select an input, click the parameter and choose from the
list that appears. The LIBRARY button opens the Channel Library window.
879
231564
11 Chapter 3Selected Channel Window
Studio Manager for DM2000 V1.1—Owner’s Manual
B GATE section
This section contains the Gate controls and display graph for the currently selected Input
Channel. The rotary controls are used to set the threshold, range, attack, decay, and hold.
The GR meter indicates the amount of gain reduction being applied by the Gate. The ON
button turns the Gate on and off. The LINK button links the Gate of the currently selected
Input Channel with the Gate of its partner channel. The KEY IN parameter is used to select
a Gate trigger source. The LIBRARY button opens the Gate Library window.
C EQUALIZER section
This section contains the EQ controls and display graph for the currently selected Input
Channel. The rotary controls are used to set the gain, center frequency, and Q of each band,
and the pre-EQ attenuation level. EQ can also be set by dragging the EQ curve on the
EQUALIZER graph. The ON button turns the EQ on and off. The TYPE buttons select the
EQ type. The LIBRARY button opens the EQ Library window.
D DELAY & PHASE section
This section contains the delay and phase controls for the currently selected Input Channel.
The rotary controls are used to set the delay time, feedback gain, and feedback mix. The ON
button turns the Delay on and off. The PHASE button reverses the channel’s signal phase.
E Routing, pan & level section
This section contains the routing, pan, and level controls and the AUTO, SOLO, and ON
buttons for the currently selected Input Channel. ROUTING buttons 1–8 are used to route
the channel to the Bus Outs. The STEREO button routes the channel to the Stereo Out. The
DIRECT button routes the channel to its Direct Out, and the parameter below it selects a
Direct Out destination. The F.PAN button turns on and off the Bus Out Follow Pan func-
tion. The PAN control is used to pan the channel. The AUTO button displays the Automix
status. The SOLO button is used to solo the channel, the ON button, to turn on and off the
channel, and the channel fader, to set the channel level.
F AUX SEND section
This section contains the Aux Send controls for the currently selected Input Channel. Use
the rotary controls to set the Aux Send levels, and click them to turn Aux Sends on and off.
Use the button below each Aux Send control to select pre-fader or post-fader. In Fixed
mode, this button is used to turn Aux Sends on and off (the level is fixed at nominal).
When Aux Sends are paired, a heart icon is displayed between them, and the odd-numbered
Aux Send control sets the level, while the even-numbered control works as a pan control.
G COMPRESSOR section
This section contains the Compressor controls and display graph for the currently selected
Input Channel. The rotary controls are used to set the threshold, ratio, attack, release, gain,
and knee. The GR meter indicates the amount of gain reduction being applied by the Com-
pressor. The OUT meter indicates its output level. The ON button turns the Compressor
on and off. The LINK button links the Compressor of the currently selected Input Channel
with the Compressor of its partner channel. The POSITION parameter is used to specify
the position of the Compressor in the signal path. The ORDER parameter is used to specify
the order of the Compressor and Insert when both are inserted at the same position. The
LIBRARY button opens the Compressor Library window.
H INSERT section
This section contains the Insert parameters for the currently selected Input Channel. The
INSERT button turns the Insert on and off. The OUT and IN parameters are used to specify
the insert out destination and insert in source respectively. The POSITION parameter is
used to specify the position of the Insert in the signal path.
Bus Outs 12
Studio Manager for DM2000 V1.1—Owner’s Manual
I Pair, FADER GROUP & MUTE GROUP section
This section contains the Pair, Fader and Mute group functions for the currently
selected Input Channel. Click the heart icon to pair and unpair the channel with its
partner channel. Use the FADER GROUP buttons to add the channel to Fader
groups, and use the MUTE GROUP buttons to add it to Mute groups.
Bus Outs
This is the Selected Channel window for Bus Outs.
A CHANNEL SELECT section
Channels can be selected by clicking the Channel ID and selecting from the list that appears,
or by clicking the left and right Channel Select buttons. The long channel name is displayed
below the Channel ID. The LIBRARY button opens the Channel Library window.
B EQUALIZER section
This section contains the EQ controls and display graph for the currently selected Bus Out.
Its layout is identical to the EQUALIZER section for Input Channels. See “EQUALIZER
section on page 11 for more information.
C DELAY section
This section contains the delay controls for the currently selected Bus Out. The rotary con-
trol is used to set the delay time, and the ON button turns the Delay function on and off.
2
34
1
765
13 Chapter 3Selected Channel Window
Studio Manager for DM2000 V1.1—Owner’s Manual
D TO STEREO & level section
This section contains the TO STEREO and level controls and the AUTO, SOLO, and ON
buttons for the currently selected Bus Out. The TO STEREO button routes the Bus Out to
the Stereo Out, and the rotary controls are used to set the Bus to Stereo level and pan. The
AUTO button displays the Automix status. The SOLO button is used to solo the Bus Out,
the ON button, to turn the Bus Out on and off, and the channel fader, to set the Bus Out
level.
E COMPRESSOR section
This section contains the Compressor controls and display graph for the currently selected
Bus Out. Its layout is identical to the COMPRESSOR section for Input Channels. See
“COMPRESSOR section on page 11 for more information.
F INSERT section
This section contains the Insert parameters for the currently selected Bus Out. The INSERT
button turns the Insert on and off. The OUT and IN parameters are used to select the insert
out destination and insert in source respectively. The POSITION parameter is used to spec-
ify the position of the Insert in the signal path.
G Pair, FADER GROUP & MUTE GROUP section
This section contains the Pair, Fader and Mute group functions for the currently selected
Bus Out. Click the heart icon to pair and unpair the channel with its partner channel. Use
the FADER GROUP buttons to add the channel to Fader groups, and use the MUTE
GROUP buttons to add it to Mute groups.
Aux Sends 14
Studio Manager for DM2000 V1.1—Owner’s Manual
Aux Sends
This is the Selected Channel window for Aux Sends.
A CHANNEL SELECT section
Channels can be selected by clicking the Channel ID and choosing from the list that
appears, or by clicking the left and right Channel Select buttons. The long channel name is
displayed below the Channel ID. The LIBRARY button opens the Channel Library window.
B EQUALIZER section
This section contains the EQ controls and display graph for the currently selected Aux Send.
Its layout is identical to the EQUALIZER section for Input Channels. See “EQUALIZER
section on page 11 for more information.
C DELAY section
This section contains the delay controls for the currently selected Aux Send. The rotary con-
trol is used to set the delay time, and the ON button turns the Delay function on and off.
D Aux Send level section
This section contains the AUTO, SOLO, and ON buttons and the channel fader for the cur-
rently selected Aux Send.
E COMPRESSOR section
This section contains the Compressor controls and display graph for the currently selected
Aux Send. Its layout is identical to the COMPRESSOR section for Input Channels. See
“COMPRESSOR section on page 11 for more information.
23
7
1
5
6
4
15 Chapter 3Selected Channel Window
Studio Manager for DM2000 V1.1—Owner’s Manual
F INSERT section
This section contains the Insert parameters for the currently selected Aux Send. The
INSERT button turns the Insert on and off. The OUT and IN parameters are used to specify
the insert out destination and insert in source respectively. The POSITION parameter is
used to specify the position of the Insert in the signal path.
G Pair, FADER GROUP & MUTE GROUP section
This section contains the Pair, Fader and Mute group functions for the currently selected
Aux Send. Click the heart icon to pair and unpair the channel with its partner channel. Use
the FADER GROUP buttons to add the channel to Fader groups, and use the MUTE
GROUP buttons to add it to Mute groups.
Matrix Sends 16
Studio Manager for DM2000 V1.1—Owner’s Manual
Matrix Sends
This is the Selected Channel window for the Matrix Sends.
A AUX section
This section contains the Aux Send-to-Matrix Send controls for the currently selected
Matrix Send. The rotary controls are used to set the Aux Send-to-Matrix Send level and pan.
A heart icon is displayed between paired Aux Sends.
B BUS section
This section contains the Bus Out-to-Matrix Send controls for the currently selected Matrix
Send. The rotary controls are used to set the Bus Out-to-Matrix Send levels and pan. A heart
icon is displayed between paired Bus Outs.
C CHANNEL SELECT section
Channels can be selected by clicking the Channel ID and choosing from the list that
appears, or by clicking the left and right Channel Select buttons. The long channel name is
displayed below the Channel ID. The LIBRARY button opens the Channel Library window.
D EQUALIZER section
This section contains the EQ controls and display graph for the currently selected Matrix
Send. Its layout is identical to the EQUALIZER section for Input Channels. See “EQUAL-
IZER section on page 11 for more information.
E DELAY section
This section contains the delay controls for the currently selected Matrix Send. The rotary
control is used to set the delay time, and the ON button turns the Delay function on and off.
2
7
6
89
143
J
5
17 Chapter 3Selected Channel Window
Studio Manager for DM2000 V1.1—Owner’s Manual
F Matrix Send level section
This section contains the balance control, AUTO, SOLO, and ON buttons and the channel
fader for the currently selected Matrix Send.
G STEREO section
This section contains the Stereo Out-to-Matrix Send controls for the currently selected
Matrix Send. The rotary controls are used to set the Stereo Out-to-Matrix Send level and
pan.
H COMPRESSOR section
This section contains the Compressor controls and display graph for the currently selected
Matrix Send. Its layout is identical to the COMPRESSOR section for Input Channels except
there is no LINK button. See COMPRESSOR section on page 11 for more information.
I INSERT section
This section contains the Insert parameters for the currently selected Matrix Send. The
INSERT button turns the Insert on and off. The OUT and IN parameters are used to specify
the insert out destination and insert in source respectively. The POSITION parameter is
used to specify the position of the Insert in the signal path.
J FADER GROUP & MUTE GROUP section
This section contains the Fader and Mute group functions for the currently selected Matrix
Send. Use the FADER GROUP buttons to add the channel to Fader groups, and use the
MUTE GROUP buttons to add it to Mute groups.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37

Yamaha V1 Bruksanvisning

Kategori
Ljudutjämnare
Typ
Bruksanvisning
Denna manual är också lämplig för