Yamaha Keyboards and Digital - Pianos Användarmanual

Kategori
Musikinstrument
Typ
Användarmanual

Denna manual är också lämplig för

IMPORTANT
Check Your Power Supply
Make sure that your local AC mains
voltage matches the voltage speci-
fied on the name plate on the bottom
panel. In some areas a voltage se-
lector may be provided on the rear
panel of the main keyboard unit near
the power cord. Make sure that the
voltage selector is set for the voltage
in your area. The voltage selector is
set at 240V when the unit is initially
shipped. To change the setting use a
“minus” screwdriver to rotate the se-
lector dial so that the correct voltage
appears next to the pointer on the
panel.
YDP-
88
II
Digital Piano
Digital Piano
Never insert or drop paper or metallic or other objects between the slits of
the key cover and the keyboard. If this happens, immediately turn off the
power and remove the electric plug from the outlet and have the instru-
ment inspected by qualified Yamaha service personnel.
Do not place the instrument against a wall (allow at least 3 cm/one-inch
from the wall), since this can cause inadequate air circulation, and possibly
result in the instrument overheating.
Read carefully the attached documentation explaining the assembly pro-
cess. Failure to assemble the instrument in the proper sequence might re-
sult in damage to the instrument or even injury.
Do not operate the instrument for a long period of time at a high or uncom-
fortable volume level, since this can cause permanent hearing loss. If you
experience any hearing loss or ringing in the ears, consult a physician.
USING THE BENCH (if included)
Do not play carelessly with or stand on the bench. Using it as a tool or step-
ladder or for any other purpose might result in accident or injury.
Only one person should sit on the bench at a time, in order to prevent the
possibility of accident or injury.
If the bench screws become loose due to extensive long-term use, tighten
them periodically using the included tool.
SAVING USER DATA
Save all data to an external device such as the Yamaha DOU-10 Disk Or-
chestra Unit, in order to help prevent the loss of important data due to a
malfunction or user operating error.
Yamaha cannot be held responsible for damage caused by improper use or modifica-
tions to the instrument, or data that is lost or destroyed.
Always turn the power off when the instrument is not in use.
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep these precautions in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock,
short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Do not open the instrument or attempt to disassemble the internal parts or
modify them in any way. The instrument contains no user-serviceable parts.
If it should appear to be malfunctioning, discontinue use immediately and
have it inspected by qualified Yamaha service personnel.
Do not expose the instrument to rain, use it near water or in damp or wet
conditions, or place containers on it containing liquids which might spill into
any openings.
If the power cord or plug becomes frayed or damaged, or if there is a sud-
den loss of sound during use of the instrument, or if any unusual smells or
smoke should appear to be caused by it, immediately turn off the power
switch, disconnect the electric plug from the outlet, and have the instru-
ment inspected by qualified Yamaha service personnel.
Only use the voltage specified as correct for the instrument. The required
voltage is printed on the name plate of the instrument.
Before cleaning the instrument, always remove the electric plug from the
outlet. Never insert or remove an electric plug with wet hands.
Check the electric plug periodically and remove any dirt or dust which may
have accumulated on it.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the
instrument or other property. These precautions include, but are not limited to, the following:
Do not place the power cord near heat sources such as heaters or radiators,
and do not excessively bend or otherwise damage the cord, place heavy
objects on it, or place it in a position where anyone could walk on, trip over,
or roll anything over it.
When removing the electric plug from an outlet, always hold the plug itself
and not the cord. Pulling by the cord can damage it.
Do not connect the instrument to an electrical outlet using a multiple-con-
nector. Doing so can result in lower sound quality, or possibly cause over-
heating in the outlet.
Remove the electric plug from the outlet when the instrument is not to be
used for extended periods of time, or during electrical storms.
Before connecting the instrument to other electronic components, turn off
the power for all components. Before turning the power on or off for all
components, set all volume levels to minimum.
Do not expose the instrument to excessive dust or vibrations, or extreme
cold or heat (such as in direct sunlight, near a heater, or in a car during the
day) to prevent the possibility of panel disfiguration or damage to the in-
ternal components.
Do not use the instrument near other electrical products such as televi-
sions, radios, or speakers, since this might cause interference which can
affect proper operation of the other products.
Do not place the instrument in an unstable position where it might acciden-
tally fall over.
Before moving the instrument, remove all connected cables.
When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners,
solvents, cleaning fluids, or chemical-impregnated wiping cloths. Also, do
not place vinyl or plastic objects on the instrument, since this might dis-
color the panel or keyboard.
Do not rest your weight on, or place heavy objects on the instrument, and
do not use excessive force on the buttons, switches or connectors.
Take care that the key cover does not pinch your fingers, and do not insert
a finger or hand in the key cover gap.
(1)B_EL/CL
The serial number of this product may be found on the bottom of the unit. You
should note this serial number in the space provided below and retain this manual
as a permanent record of your purchase to aid identification in the event of theft.
Model No.
Serial No.
Contents
The Control Panel.........................................................2
Connections .................................................................. 4
Selecting & Playing Voices .......................................... 5
Playing the Demonstration Tunes ............................... 6
The Dual Mode ............................................................. 7
Adjusting the Balance Between the Dual-mode
Voices .............................................................. 7
Shifting a Dual-Mode Voice Up One Octave .... 7
The Pedals .................................................................... 8
Soft (Left) Pedal ............................................... 8
Sostenuto (Center) Pedal................................. 8
Damper (Right) Pedal....................................... 8
Transposition ................................................................ 8
Pitch Control................................................................. 9
Tuning Up ......................................................... 9
Tuning Down..................................................... 9
To Restore Standard Pitch ............................... 9
The Metronome & Tempo Control ............................. 10
The Metronome ................................................. 10
Metronome Volume ........................................ 10
Metronome Time Signature............................ 10
Tempo Control ...................................................10
Using the Recorder .................................................... 11
Recording .......................................................... 11
Changing the Initial Settings .......................... 12
Erasing the recorded data.............................. 12
Playback ............................................................12
Fast Forward Playback...................................12
MIDI Functions ...........................................................13
A Brief Introduction to MIDI ............................ 13
MIDI “Messages” Transmitted & Received by
the YDP-88II ....................................................... 13
MIDI Transmit & Receive Channel Selection.. 14
MIDI Transmit Transpose................................14
Other MIDI Functions ....................................... 14
Local Control ON/OFF ................................... 15
Program Change ON/OFF .............................15
Control Change ON/OFF ............................... 15
The Multi-Timbre Mode .................................. 16
The MIDI Split & Left Local OFF Mode ..........16
Bulk Data Dump .............................................16
Troubleshooting ..........................................................17
Options & Expander Modules ...................................17
Keyboard Stand Assembly ........................................18
MIDI Data Format ......................................................24
MIDI Implementation Chart....................................... 25
Specifications.............................................................. 26
Introduction
Thank you for choosing a Yamaha YDP-88II Digital Piano. Your YDP-88II is a fine musical instrument
that employs advanced Yamaha music technology. With the proper care, your YDP-88II will give you many
years of musical pleasure.
Yamaha’s AWM (Advanced Wave Memory) tone
generator system offers rich, realistic voices.
Touch-sensitive keys provides extensive expres-
sive control and outstanding playability.
Dual play mode allows 2 voices to be played
simultaneously.
Metronome feature with variable tempo facilitates
practice.
Record and play back anything you play on the
keyboard (up to approximately 1,300 notes).
MIDI compatibility and a range of MIDI functions
make the YDP-88II useful in a range of advanced
MIDI music systems.
In order to make the most of your YDP-88II’s performance potential and features, we urge you to read
this Owner’s Manual thoroughly, and keep it in a safe place for later reference.
2
The Control Panel
1 [POWER] Switch
Press the [POWER] switch once to turn the power
ON, a second time to turn the power OFF. When the
power is initially turned ON, the [PIANO] voice
selector LED will light.
2 [MASTER VOLUME] Control
The [MASTER VOLUME] control adjusts the
volume (level) of sound produced by the YDP-88II’s
internal stereo sound system. The [MASTER VOL-
UME] control also adjusts headphone volume when a
pair of headphones is plugged into the PHONES jack
(page 5).
3 [MIDI/TRANSPOSE] Button
The [MIDI/TRANSPOSE] button allows access
to the YDP-88II’s TRANSPOSE function (to shift the
pitch of the entire keyboard up or down) and MIDI
functions. For details refer to “TRANSPOSITION”
on page 8, and “MIDI FUNCTIONS” on page 13,
respectively.
4 Voice Selectors
The YDP-88II has five voice selectors. Simply
press any of the voice selectors to select the corre-
sponding voice. The voice selector LED will light to
indicate which voice is currently selected.
The YDP-88II also has a DUAL mode in which
two voices can be played simultaneously across the
full range of the keyboard — see page 7 for details.
NOTE
The PIANO voice is automatically selected
whenever the [POWER] switch is initially turned
ON.
5 [METRONOME] Button
Turns the metronome sound on and off. The
[TEMPO] control, below, is used to set the tempo of
the metronome sound. More precise tempo settings
can be achieved by using the [METRONOME]
button and the YDP-88II keyboard as described on
page 10.
6 [TEMPO] Control
This control adjusts the tempo of the YDP-88II
metronome function as well as the playback tempo of
the recorder function. The tempo range is from 32 to
280 quarter-note beats per minute.
7 RECORDER [PLAY] and [REC]
Buttons
These buttons control the YDP-88II recorder,
letting you record and play back just about anything
you play on the keyboard — up to a maximum of
about 1,300 notes. See page 11 for details.
POWER
B0A0G0F0E0D0C0B-1A-1
C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 G2 A2 B2 C3 D3 E3 F3 A3 B3 C4 D4 E4 F4 G4F2 G3
1
F2 G3
PHONES Jacks
(Bottom Panel)
Left voice shift up key
(See page 7)
Pitch control keys
(See page 9)
Transpose keys
(See page 8)
Balance keys (See page 7)
ORGANE. PIANO 2
MIN MAX
MASTER VOLUME
PIANO
METRONOME
E. PIANO 1
HARPSI-
CHORD
MIDI/TRANSPOSE
32 280120
TEMPO
PLAY REC
RECORDER
DEMO
234 5 768
PIANO
E. PIANO 2
METRONOME
E. PIANO 1
HARPSI-
CHORD
MIDI/TRANSPOSE
PLAY REC
RECORDER
DEMO
ORGAN
MIN MAX
MASTER VOLUME
32 280120
TEMPO
3
The Control Panel
8 [DEMO] Button
Activates the demo playback mode in which you
can select playback of five pre-programmed demon-
stration sequences. See page 6 for details.
9 Pedals
The soft (left), sostenuto (center) and damper
(right) pedals provide a range of expressive control
capabilities similar to the pedal functions on an
acoustic piano. See page 8 for details.
D6 E6 F6 G6 A6 B6 C7
A4 B4 C5 D5 E5 F5 G5 A5 B5 C6
Right voice shift up key
(See page 6)
DIGITAL PIANO YDP-88II
Key Cover
Hold the cover with both hands when moving it, and do not
release it until it is fully opened or closed. Be careful to
avoid catching fingers (yours or others) between the cover
and main unit.
Do not place objects on top of the key cover. Small objects
placed on the key cover may fall inside the main unit when
the cover is opened and may not be able to be removed.
This could cause electric shock, short circuit, fire or other
serious damage to the instrument.
To open the key cover:
ZLift the cover slightly (not too much).
XSlide the cover open.
To close the key cover:
ZSlide the cover toward you.
XGently lower the cover over the keys.
Be careful to avoid catching your
fingers when opening or closing
the cover.
If you will be using sheet music with your
YDP-88II, raise the music stand built into its top
panel by lifting the rear edge of the music stand,
then flip down the music stand braces and engage
them with the corresponding recesses.
The music stand can be lowered after slightly
lifting it and folding the two brackets which
support it against the back of the stand.
Do not try to use the music stand in a half-raised
position. Also, when lowering the stand, make sure to
press it until it is all the way down.
The Music Stand
Soft pedal
9
Damper pedal
Sostenuto pedal
4
Connections
1 AUX OUT L/L+R and R Jacks
The AUX OUT L/L+R and R jacks deliver the output of the
YDP-88II for connection to an instrument amplifier, mixing console,
PA system, or recording equipment. If you will be connecting the
YDP-88II to a monaural sound system, use only the L/L+R jack.
When a plug is inserted into the L/L+R jack only, the left- and right-
channel signals are combined and delivered via the L/L+R jack so
you don’t lose any of the YDP-88II’s sound.
2 MIDI IN and OUT Connectors
The MIDI IN connector receives MIDI data from an external
MIDI device (such as the DOU-10 Disk Orchestra Unit) which can
be used to control the YDP-88II. The MIDI OUT connector trans-
mits MIDI data generated by the YDP-88II (e.g. note and velocity
data produced by playing the YDP-88II keyboard).
More details on MIDI are given in “MIDI FUNCTIONS” on
page 13.
PHONES Jacks
(Bottom Panel)
Two pairs of standard pair of stereo headphones can be plugged
in here for private practice or late-night playing. The internal
speaker system is automatically shut off when a pair of headphones
is plugged into either of the PHONES jacks.
MIDI
IN OUT
DOU-10
12
MIDI
IN
OUT
AUX OUT
R L/L+R
130V
110V
240V
220V
VOLTAGE
SELECTOR
AUX OUT
L/L+RR
Stereo System
5
Selecting & Playing Voices
Turn Power On...................................................................................................
After making sure that the YDP-88II’s AC cord is properly plugged
into a convenient AC wall outlet, press the [POWER] switch located to
the left of the keyboard to turn the power ON. In some areas a plug
adaptor may be provided to match the pin configuration of the AC wall
outlets in your area.
When the power is turned ON, the [PIANO] voice selector LED
will light (the PIANO voice is automatically selected whenever the
power is turned ON).
Set the Volume ..................................................................................................
Initially set the [MASTER VOLUME] control about half way
between the “MIN” and “MAX” settings. Then, when you start playing,
re-adjust the [MASTER VOLUME] control for the most comfortable
listening level.
Select a Voice .....................................................................................................
Select the desired voice by pressing one of the voice selectors.
POWER
Play................................................................................................................................
The YDP-88II offers keyboard touch response, so the volume and
timbre of notes played can be controlled according to how “hard” you
play the keys. The amount of variation available depends on the se-
lected voice.
PIANO
E. PIANO 2
E. PIANO 1
HARPSI-
CHORD
ORGAN
MIN MAX
MASTER VOLUME
6
The YDP-88II includes five demo tunes that effectively demonstrate its sound
capabilities. Here’s how you can select and play the demo tunes:
Playing the Demonstration Tunes
Engage the Demo Mode .........................................................................
Select a Demo Tune.....................................................................................
Press one of the flashing voice selectors to start playback of the
corresponding demo tune — featuring the voice normally selected by
that voice selector button. The demo tunes will play in sequence until
stopped, starting with the selected tune. The voice selector indicator
will flash during demo playback.
The Demo Tunes
• [PIANO] button:..................... Piano Sonata A major K.V. 331 3rd movement
“Turkischer Marsch” by W. A. Mozart
• [E. PIANO 1] button: ............. “Pavane pour une infante défunte” by M. J.
Ravel
• [HARPSICHORD] button: ..... “The Harmonious Blacksmith” by G. F. Händel
• [ORGAN] button:................... Wedding March from “A Midsummer Night
Dream” by J. L. F. Mendelssohn
* The demonstration pieces listed above are short excerpts from the original composi-
tions. The other demo tune is original (© 1997 by YAMAHA CORPORATION).
Press the [DEMO] button to engage the demo mode — the voice
selectors will flash in sequence.
Use the [MASTER VOLUME] control to adjust the volume.
NOTE
The [TEMPO] control does not affect demo playback.
Play a Different Demo ...............................................................................
You can start playback of any other demo tune during playback by
simply pressing the corresponding voice selector. Playback will stop
and the playback-ready mode described in step 2, above, will be re-
engaged if you press the voice selector of the demo that is currently
playing.
Stop the Demo ..................................................................................................
Press the [DEMO] button when you want to stop demo playback
and return to the normal play mode.
DEMO
DEMO
PIANO
E. PIANO 2
E. PIANO 1
HARPSI-
CHORD
ORGAN
MIN MAX
MASTER VOLUME
Set the Volume ..................................................................................................
7
The Dual Mode
The DUAL mode makes it possible to play two voices simultaneously across
the entire range of the keyboard. To activate the DUAL mode simply press two
voice selectors at the same time (or press one voice selector while holding
another). The voice indicators of both selected voices will light when the DUAL
mode is active. To return to the normal single-voice play mode, press any single
voice selector.
Adjusting the Balance Between the Dual-mode
Voices
.........................................................................................................................
Shifting a Dual-Mode Voice Up One Octave......................
Depending on which voices you combine using the DUAL mode,
the combination may sound better if one of the voices is shifted up an
octave. To shift the right voice, press the C5 key while pressing the two
voice selectors corresponding to the voices to be combined in the
DUAL mode. Press C5 again to shift the voice back to its normal range.
Use the C1 key in the same way to shift the left voice.
All voice combinations are set to the same octave by default.
The volume levels of the two voices combined in the DUAL mode
are normally set automatically to produce a pleasing balance (see
“Default Settings” below). The balance can be adjusted manually by
using the C2 through C4 keys on the keyboard while pressing the two
voice selectors corresponding to the voices to be combined in the
DUAL mode.
The C3 key produces equal (50:50) balance between the two voices,
while keys to the left of C3 increase the volume of the left voice in
relation to the right voice, and keys to the right of C3 increase the
volume of the right voice in relation to the left voice. By “left” and
“right” voice we refer to the relative positions of the voice selectors —
i.e. in a HARPSICHORD/ORGAN combination HARPSICHORD is
the left voice and ORGAN is the right voice.
Default Settings
Voice Combinations Balance keys
PIANO/ORGAN ....................................... E2
E. PIANO 1/ORGAN................................ F2
E. PIANO 2/ORGAN................................ E2
HARPSICHORD/ORGAN........................ G2
* All other voice combinations are set to C3 (equal balance).
Equal
balance.
Left voice
maximum.
Right voice
maximum.
C
3
C
2
C
4
P
IANO 2
HARPSI-
CHORD
ORGAN
P
IANO 2
HARPSI-
CHORD
ORGAN
Left voice
shift up.
Right voice
shift up.
C
1
C
5
The Pedals
Transposition
Z Press and hold the [MIDI/TRANSPOSE] button.
X Press a key between F#2 and F#3 according to the desired amount
of transposition.*
C Release the [MIDI/TRANSPOSE] button.
* Pressing the C3 key produces normal keyboard pitch. Pressing the
key to the left of C3 (B2) transposes the pitch of the keyboard down
a semitone, the next key to the left (Bb2) transposes down a whole
tone (two semitones), etc., down to the F#2 key which transposes
down 6 semitones. Upward transposition is accomplished in the
same way using the keys to the right of C3, up to F#3 which trans-
poses up 6 semitones.
NOTE
Notes below and above the A-1 — C7 of the YDP-88
II
sound one octave
higher and lower, respectively.
The [MIDI/TRANSPOSE] button and keys F#2 through F#3 on the keyboard are used for transposition.
The YDP-88II has three foot pedals that produce a range of expressive
effects similar to those produced by the pedals on an acoustic piano.
The YDP-88IIs TRANSPOSE function makes it possible to shift the pitch of
the entire keyboard up or down in semitone intervals up to a maximum of six
semitones. “Transposing” the pitch of the YDP-88II keyboard facilitates playing in
difficult key signatures, and you can easily match the pitch of the keyboard to the
range of a singer or other instrumentalist.
MIDI/TRANSPOSE
C
3
F#
2
Normal
pitch.
Transpose
down.
Transpose
up.
F
#
3
-5 -3 -1 0 +2 +4 +5
-6 -4 -2 +1
+3 +6
Soft pedal
Damper pedal
Sostenuto pedal
Soft (Left) Pedal...............................................................................................
The soft pedal reduces the volume and slightly changes the timbre of
notes played while the pedal is pressed. The soft pedal will not affect
notes which are already playing when it is pressed.
Damper (Right) Pedal ................................................................................
The damper pedal functions in the same way as a damper pedal on
an acoustic piano. When the damper pedal is pressed notes played have
a long sustain. Releasing the pedal immediately stops (damps) any
sustained notes.
Sostenuto (Center) Pedal......................................................................
If you play a note or chord on the keyboard and press the sostenuto
pedal while the note(s) are held, those notes will be sustained as long as
the pedal is held (as if the damper pedal had been pressed) but all
subsequently played notes will not be sustained. This makes it possible
to sustain a chord, for example, while other notes are played “staccato.
8
Pitch Control
Pitch control makes it possible to tune the YDP-88II over a ±50-cent range
(approximate) in approximately 1.6-cent intervals. A hundred “cents” equals one
semitone, so the tuning range provided allows fine tuning of overall pitch over a
range of approximately a semitone. Pitch control is useful for tuning the YDP-
88II to match other instruments or recorded music.
Tuning Up ...............................................................................................................
Z To tune up (raise pitch), hold the A-1 and B-1 keys simultaneously.
X Press any key between C3 and B3. Each time a key in this range is
pressed the pitch is increased by approximately 1.6 cents, up to a
maximum of 50 cents above standard pitch.
C Release the A-1 and B-1 keys.
Tuning Down.......................................................................................................
Z To tune down (lower pitch), hold the A-1 and A#-1 keys simulta-
neously.
X Press any key between C3 and B3. Each time a key in this range is
pressed the pitch is decreased by approximately 1.6 cents, up to a
maximum of 50 cents below standard pitch.
C Release the A-1 and A#-1 keys.
To Restore Standard Pitch*.................................................................
Z To restore standard pitch (A3 = 440 Hz), hold the A-1, A#-1 and
B-1 keys simultaneously.
X Press any key between C3 and B3.
C Release the A-1, A#-1 and B-1 keys.
* Standard pitch (A3 = 440 Hz) is set when the [POWER] switch is
initially turned ON.
NOTE
The PITCH CONTROL function has no effect when LOCAL OFF is active
(see “MIDI FUNCTIONS,” page 13).
C
3
B
3
A
-1
B
-1
A
-1
A#
-1
C
3
B
3
A
-1
B
-1
A#
-1
C
3
B
3
9
The Metronome & Tempo Control
The YDP-88II built-in metronome is a convenient feature for practice, and it
can also provide a solid rhythmic guide when recording using the Recorder
feature, described below.
The Metronome
The metronome sound is turned on and off via the [METRO-
NOME] button. Press the [METRONOME] button so that its indicator
lights to turn the metronome on, then again so the indicator goes out to
turn the metronome off.
Metronome Volume ......................................................................................
The volume of the metronome sound can be independently adjusted
by using the [TEMPO] control while holding the [METRONOME]
button. Sliding the control to the right increases the metronome volume.
Metronome Time Signature.................................................................
The time signature of the metronome sound can be set by pressing
the appropriate voice selector button while holding the [METRO-
NOME] button, as follows:
[METRONOME] + [PIANO] No accent (default)
[METRONOME] + [E. PIANO 1] 2 time
[METRONOME] + [E. PIANO 2] 3 time
[METRONOME] + [HARPSICHORD] 4 time
[METRONOME] + [ORGAN] 6 time
Tempo Control
The tempo of the metronome and recorder playback can be con-
trolled in two ways:
Use the panel [TEMPO] control to set the required tempo from 32
to 280 quarter-note beats per minute.
For more precise tempo settings press the appropriate key on the
keyboard while holding the [METRONOME] button.
A
-1
C
0
C
1
C
2
C
3
C
4
C
5
C
6
32
36
38
34
42
46
48
52
56
60
62
40
44
50
54
58
66
70
72
76
80
84
86
64
68
74
78
82
90
94
96
100
104
108
110
88
92
98
102
106
114
118
120
124
128
132
134
112
116
122
126
130
138
142
144
148
152
156
158
136
140
180
188
196 232
248
264208
216
146
150
154
164
172
176
184
192
200
204
212
220
224
240
256
272
280
160
168
C
7
Tempo
Tempo
Tempo/Key Chart
E. PIANO 2
METRONOME
A
NO 1
HARPSI-
CHORD
ORGAN
METRONOME
METRONOME
32 280120
TEMPO
METRONOME
32 280120
TEMPO
10
The YDP-88II recorder lets you record what you play on the keyboard and
then play it back. This is a useful adjunct to any keyboard study program, since it
lets you hear exactly how you sound from the listener’s perspective. It can also
be just plain fun.
The recorder actually records the following data:
Notes played Voice selection
Dual mode voices Dual balance Dual mode octave shift
Damper pedal Soft pedal
Sostenuto pedal (not recorded as an initial setting)
Tempo (Initial setting only.)
Using the Recorder
Press either the RECORDER [REC] or [PLAY] button to stop
recording.
Recording
Engage the Record Ready Mode ..................................................
Press the RECORDER [REC] button to engage the record ready
mode (recording does not actually start yet). The [REC] button indica-
tor will light.
Make All Necessary Initial Settings ...........................................
Before actually beginning to record, select the voice you want to
record with (or voices if you will be using the dual mode). You might
also want to set the volume and tempo controls.
Start Recording................................................................................................
Recording will begin automatically as soon as you play a note on the
keyboard or press the [PLAY] button.
NOTE
If the metronome was on when you started recording, you’ll be able to
keep time with the metronome while recording, but the metronome sound
will not be recorded.
You can record up to a maximum of about 1,300 notes, depending on
pedal usage and other factors. The [REC] button indicator will begin to
flash when recorder memory is almost full, and recording will stop
automatically.
Stop Recording................................................................................................
PLAY REC
RECORDER
PIANO
E. PIANO 2
E. PIANO 1
HARPSI-
CHORD
ORGAN
PLAY REC
RECORDER
11
Using the Recorder
Changing the Initial Settings.............................................................
The initial voice (including dual mode) and tempo settings made in
step 2 of the recording procedure are actually recorded by the YDP-
88II. These initial settings can be changed after the recording is finished
by pressing the [REC] button to engage the record ready mode, making
the required changes, and then pressing the [REC] button again to exit
from the record ready mode and register the changes. If you do this, be
careful not to press the [PLAY] button or a key on the keyboard, either
of which will start recording and erase all previous recorded data.
Erasing the recorded data....................................................................
The recorded data can be erased by first pressing the [REC] button
to engage the record ready mode, and then pressing the [PLAY] button
twice without recording any data.
Playback
To play back what you’ve recorded, simply press the RECORDER
[PLAY] button. Playback starts from the beginning of the recorded
data, and will stop automatically at the end of the recorded data. You
can also stop playback at any time by pressing the [PLAY] button.
NOTE
It is possible to play along on the keyboard during playback.
The playback volume and tempo can be adjusted by using the [MASTER
VOLUME] and [TEMPO] controls, respectively.
If the metronome is being used during playback, the metronome will stop
when playback is stopped.
All recorder data will be erased when the YDP-88
II
power is turned off. It
is possible to store recorded data to an external MIDI storage device such
as the Yamaha DOU-10 Disk Orchestra Unit by using the Bulk Dump
function described on page 16.
The playback data is not transmitted via the MIDI OUT connector.
Fast Forward Playback ............................................................................
When you want to locate a specific point in a recording you can
quickly move forward through the recording while monitoring the
sound by pressing the [REC] button while holding the [MIDI/TRANS-
POSE] button.
PLAY REC
RECORDER
MIDI/TRANSPOSE
PLAY REC
RECORDER
12
MIDI Functions
A Brief Introduction to MIDI...............................................................................................................................................
The MIDI information (messages) transmitted and received by
the YDP-88II are as follows:
Note and Velocity Data
This information tells the receiving keyboard or tone generator to
play a certain note (specified by the MIDI note number) at a certain
dynamic level (specified by the MIDI velocity value). Note and
velocity data is transmitted by the YDP-88II whenever a key is
pressed, and the YDP-88II’s internal AWM tone generator will “play”
the corresponding note(s) whenever note and velocity data is received
from an external MIDI device.
Program Change Numbers
The YDP-88II transmits a MIDI program change number between
0 and 4 when one of its voice selectors is pressed. This normally
causes the correspondingly numbered voice to be selected on a
receiving MIDI device. The YDP-88II will respond in the same way,
automatically selecting the appropriate voice when a MIDI program
change number is received. See “Program Change ON/OFF” on page
15 for information on turning program change number reception and
transmission ON or OFF.
MIDI “Messages” Transmitted & Received by the YDP-88II............................................................
Control Change Numbers
Control Change data representing Damper pedal operation is
transmitted by the YDP-88II whenever one of these pedals is used. If
the receiving device is a tone generator or another keyboard, it will
respond in the same way as the YDP-88II’s internal tone generator
when one of the pedals is used. The YDP-88II also receives and
responds to the appropriate control change data. See “Control Change
ON/OFF” on page 15 for information on turning control change
number reception and transmission ON or OFF.
MIDI, the Musical Instrument Digital Interface, is a world-
standard communication interface that allows MIDI-compatible
musical instruments and equipment to share musical information and
control one another. This makes it possible to create “systems” of
MIDI instruments and equipment that offer far greater versatility and
control than is available with isolated instruments. For example, most
MIDI keyboards (including the YDP-88II, of course) transmit note
and velocity (touch response) information via the MIDI OUT
connector whenever a note is played on the keyboard. If the MIDI
OUT connector is connected to the MIDI IN connector of a second
keyboard (synthesizer, etc.) or a tone generator (essentially a
synthesizer with no keyboard), the second keyboard or tone generator
will respond precisely to notes played on the original transmitting
keyboard. The result is that you can effectively play two instruments
at once, providing thick multi-instrument sounds.
This same type of musical information transfer is used for MIDI
sequence recording. A sequence recorder can be used to “record”
MIDI data received from a YDP-88II, for example. When the
recorded data is played back, the YDP-88II automatically “plays” the
recorded performance in precise detail.
The examples given above really only scratch the surface. MIDI
can do much, much more. The YDP-88II offers a number of MIDI
functions that allows it to be used in fairly sophisticated MIDI
systems.
NOTE
Always use a high-quality MIDI cable to connect MIDI
OUT to MIDI IN terminals. Never use MIDI cables
longer than about 15 feet, since cables longer than this
can pick up noise which can cause data errors.
DOU-10
MIDI Cable
MIDI INMIDI OUT
YDP-88II
DOU-10
YDP-88II
Data Being Recorded
Playback Data
MIDI IN MIDI INMIDI OUTMIDI OUT
13
MIDI Functions
MIDI Transmit & Receive Channel Selection...................................................................................................
Setting the YDP-88II MIDI Channels
(Set to receive on MIDI
channel 2)
(Set to receive on MIDI channel 1)
For setting the transmit
channel. (C1 ~ D#2)
For setting the receive
channel. (C4 ~ D#5)
For OMNI mode
ZPress and hold the [MIDI/TRANSPOSE] button.
XPress the key on the keyboard corresponding to the desired MIDI
transmit or receive channel.*
CRelease the [MIDI/TRANSPOSE] button.
* Keys C1 through D#2 on the keyboard are used to set the MIDI
transmit channel, and keys C4 through D#5 are used to turn the
OMNI mode OFF and set the MIDI receive channel as shown in
the illustration to the left. The E5 key sets the OMNI receive
mode and basic receive channel 1.
NOTE
When the power is initially turned ON, MIDI receive is
set to the OMNI mode and the transmit channel is set
to 1.
The MIDI system allows transmission and reception of MIDI data
on 16 different channels. Multiple channels have been implemented
to allow selective control of certain instruments or devices connected
in series. For example, a single MIDI sequence recorder could be
used to “play” two different instruments or tone generators. One of
the instruments or tone generators could be set to receive only on
channel 1, while the other is set to receive on channel 2. In this
situation the first instrument or tone generator will respond only to
channel-1 information transmitted by the sequence recorder, while the
second instrument or tone generator will respond only to channel-2
information. This allows the sequence recorder to “play” two
completely different parts on the receiving instruments or tone
generators.
In any MIDI control setup, the MIDI channels of the transmitting
and receiving equipment must be matched for proper data transfer. An
“OMNI” receive mode is also available, which allows reception on all
16 MIDI channels. In the OMNI mode it is not necessary to match
the receive channel of the receiving device to the transmit channel of
the transmitting device (except when receiving mode messages).
Other MIDI Functions
The MIDI functions listed to the right are engaged by holding
down the [MIDI/TRANSPOSE] button and pressing the correspond-
ing voice selector. Full details are given in the following pages.
Function YDP-88II Voice Selector
Local Control ON/OFF [PIANO]
Program Change ON/OFF [E. PIANO 1]
Control Change ON/OFF [E. PIANO 2]
Multi-Timbre Mode [HARPSICHORD]
MIDI Split & Left Local OFF [ORGAN]
MIDI FUNCTION CHART
MIDI Transmit Transpose.......................................................................................................................................................
This function allows the MIDI note data transmitted by the YDP-
88II to be transposed up or down in semitone increments by up to
plus or minus 6 semitones. The pitch of the YDP-88II itself is not
affected.
Setting the MIDI Transpose Function
ZPress and hold the [MIDI/TRANSPOSE] button.
XPress the key on the keyboard corresponding to the desired
amount of transposition.*
CRelease the [MIDI/TRANSPOSE] button.
* Keys F#5 through F#6 on the keyboard are used to set the MIDI
transmit transpose function as shown in the illustration to the left.
NOTE
When the power is turned ON, MIDI transmit transpose
is set to 0 (no transposition).
Tone Generator
MIDI IN
MIDI IN MIDI THRU
DOU-10
MIDI OUT
YDP-88II
C
1
D#
2
C
4
D#
5
1356810121315
2 4 7 9 11 14 16
1356810121315
2 4 7 9 11 14 16
E
5
MIDI/TRANSPOSE
C
6
F#
5
F#
6
-6 -4 -2 +1 +
3
+
6
+5+4+20-1-3-5
MIDI/TRANSPOSE
14
MIDI Functions
Local Control ON/OFF .............................................................................................................................................................
“Local Control” refers to the fact that, normally, the YDP-88II
keyboard controls its internal tone generator, allowing the internal
voices to be played directly from the keyboard. This situation is
“Local Control ON” since the internal tone generator is controlled
locally by its own keyboard.
Local control can be turned OFF, however, so that the YDP-88II
keyboard does not play the internal voices, but the appropriate MIDI
information is still transmitted via the MIDI OUT connector when
notes are played on the keyboard. At the same time, the internal tone
generator responds to MIDI information received via the MIDI IN
connector.
When using the DOU-10 Disk Orchestra Unit with the YDP-88II,
for example, Local Control should be turned OFF when recording
using the DOU-10 voices only, and ON when recording the YDP-88II
voices while listening to playback of the DOU-10 voices.
= Local Control OFF
= Local Control ON
ZHold down the [MIDI/TRANSPOSE] button.
XPress the [PIANO] voice selector. If the PIANO LED is lit when
the [PIANO] voice selector is pressed, you have turned local
control OFF. If the PIANO LED is not lit when the [PIANO]
voice selector is pressed, you have turned local control ON.
CRelease the [MIDI/TRANSPOSE] button.
Control Change ON/OFF.......................................................................................................................................................
Normally the YDP-88II will respond to MIDI control change data
received from an external MIDI device or keyboard, causing the
selected YDP-88II voice to be affected by pedal and other “control”
settings received from the controlling device. The YDP-88II also
transmits MIDI control change information when one of its pedals are
operated.
This function makes it possible to cancel control change data
reception and transmission if you do not want the YDP-88II voices to
be affected by control change data received from an external device
or vice versa.
= Control Change OFF
= Control Change ON
ZHold down the [MIDI/TRANSPOSE] button.
XPress the [E. PIANO 2] voice selector. If the E. PIANO 2 LED is
lit when the [E. PIANO 2] voice selector is pressed, you have
turned control change reception/transmission OFF. If the E.
PIANO 2 LED is not lit when the [E. PIANO 2] voice selector is
pressed, you have turned control change reception/transmission
ON.
CRelease the [MIDI/TRANSPOSE] button.
Program Change ON/OFF....................................................................................................................................................
Normally the YDP-88II will respond to MIDI program change
numbers received from an external keyboard or other MIDI device,
causing the correspondingly numbered YDP-88II voice to be selected.
The YDP-88II will normally also send a MIDI program change
number whenever one of its voices is selected, causing the corre-
spondingly numbered voice or program to be selected on the external
MIDI device if the device is set up to receive and respond to MIDI
program change numbers.
This function makes it possible to cancel program change number
reception and transmission so that voices can be selected on the YDP-
88II without affecting the external MIDI device, and vice versa.
= Program Change OFF
= Program Change ON
ZHold down the [MIDI/TRANSPOSE] button.
XPress the [E. PIANO 1] voice selector. If the E. PIANO 1 LED is
lit when the [E. PIANO 1] voice selector is pressed, you have
turned program change reception/transmission OFF. If the E.
PIANO 1 LED is not lit when the [E. PIANO 1] voice selector is
pressed, you have turned program change reception/transmission
ON.
CRelease the [MIDI/TRANSPOSE] button.
PIANO E. PI
A
MIDI/TRANSPOSE
PIANO
PIANO
N
O E. PIANO1 E. P
I
MIDI/TRANSPOSE
E. PIANO1
E. PIANO1
N
O1 E. PIANO2
HA
R
CH
O
MIDI/TRANSPOSE
E. PIANO2
E. PIANO2
15
MIDI Functions
The Multi-Timbre Mode...........................................................................................................................................................
The Multi-Timbre mode is a special mode in which the YDP-88II
voices can be independently controlled on different MIDI channel
numbers by an external MIDI device. The Multi-Timbre mode can be
activated as follows:
= Multi-Timbre Mode ON
= Multi-Timbre Mode OFF
ZHold down the [MIDI/TRANSPOSE] button.
XPress the [HARPSICHORD] voice selector. If the HARPSI-
CHORD LED is lit when the [HARPSICHORD] voice selector
is pressed, you have turned the Multi-Timbre mode ON. If the
HARPSICHORD LED is not lit when the [HARPSICHORD]
voice selector is pressed, you have turned the Multi-Timbre mode
OFF.
CRelease the [MIDI/TRANSPOSE] button.
The MIDI Split & Left Local OFF Mode...................................................................................................................
In the MIDI split mode one section of the YDP-88II keyboard is
used to play a YDP-88II voice in the normal way, while the remaining
section is used to play a second MIDI keyboard or tone generator
such as the Yamaha DOU-10 Disk Orchestra Unit. In this mode the
right-hand section of the keyboard is used to play an internal YDP-
88II voice, while the left-hand section of the keyboard plays the
external keyboard or tone generator. Playing the left-hand section of
the keyboard produces no sound from the YDP-88II. The “split
point, or the key that divides the left- and right-hand sections of the
keyboard can be set at any desired key.
SPLIT POINT
Left-hand section plays
a DOU-10 bass voice.
Right-hand section plays a
YDP-88II piano voice.
ZPress the [ORGAN] voice selector while holding down the
[MIDI/TRANSPOSE] button. The ORGAN LED will flash.
XWhile still holding the [MIDI/TRANSPOSE] button, press the
key on the keyboard at which you want to set the split point. The
ORGAN LED will light continuously. The split-point becomes
the first key of the left-hand section.
CRelease the [MIDI/TRANSPOSE] button.
VTo return to the normal full-keyboard mode, hold the [MIDI/
TRANSPOSE] button and press the [ORGAN] voice selector,
then release both buttons.
NOTE
When the power is turned ON the default split point key
— F
#
2 — will be automatically selected. If a new split
point is selected it remains active until the power is
turned OFF or a different split point is selected.
Bulk Data Dump .............................................................................................................................................................................
This function is used to transmit all data stored in the Recorder
memory to a MIDI data storage device such as the Yamaha DOU-10
Disk Orchestra Unit, other sequence recorders, or MIDI compatible
computers.
ZHold [MIDI/TRANSPOSE] and press the [PLAY] button.
Transmission will begin.
XRelease the buttons.
NOTE
Bulk dump will not function when the metronome is on
or when the recorder is in operation.
(Set to receive on MIDI
channel 2)
The MIDI split mode is useful if, for example, you want to play a
piano (YDP-88II) voice with the right hand while playing a synthe-
sizer bass line or string section with the left hand.
When the MIDI split mode is activated, notes played on the left-
hand section are transmitted via the YDP-88II MIDI OUT connector
on MIDI channel 2. Notes played on the right-hand section are
transmitted on the “basic channel” (i.e. the channel set using the
MIDI channel selection function described previously).
O
R
HARPSI-
CHORD
N
O2
MIDI/TRANSPOSE
HARPSI-
CHORD
HARPSI-
CHORD
ORGAN
H
ARPSI-
C
HORD
MIDI/TRANSPOSE
DOU-10
OUT PUT
R
L
AUX IN
L
RMIDI OUT
MIDI
IN
YDP-88II
MIDI/TRANSPOSE
RECORDER
PLAY REC
16
Troubleshooting
If you encounter what appears to be a malfunction, please check the follow-
ing points before assuming that your YDP-88II is faulty.
1.No Sound When the Power is Turned ON
Is the AC plug properly connected to an AC wall outlet? Check the AC connection carefully. Is the
MASTER VOLUME control turned up to a reasonable listening level?
Also make sure that a pair of headphones is not plugged into the PHONES jack, and the Local
Control (page 15) is ON.
2.The Damper Pedal Doesn’t Work
If the damper pedal doesn’t work, or notes are sustained even when the pedal is not pressed, make sure
that the pedal cord is properly plugged into the main unit (page iii).
3.The YDP-88II Reproduces Radio or TV Sound
This can occur if there is a high-power transmitter in your vicinity. Contact your Yamaha dealer.
4.Intermittent Static Noise
This is usually due to turning ON or OFF a household appliance or other electronic equipment which is
fed by the same AC mains line as your YDP-88II.
5.Interference Appears On Radio or TV Sets Located Near the YDP-88II
The YDP-88II contains digital circuitry which can generate radio-frequency noise. The solution is to
move the YDP-88II further away from the affected equipment, or vice versa.
6.Distorted Sound When the YDP-88II is Connected to An External Amplifier/Speaker System
If the YDP-88II is connected to a stereo system or instrument amplifier and the sound is distorted,
reduce the setting of the YDP-88II volume control to a level at which the distortion ceases.
Options & Expander Modules
Options
BC-8 Bench
A comfortable bench styled to match your Yamaha YDP-88II.
HPE-160 Stereo Headphones
High-performance lightweight dynamic headphones with extra-soft ear pads.
Expander Modules
DOU-10 Disk Orchestra Unit
A range of MIDI recording and playback functions, plus Yamaha DOC software, Disklavier
PianoSoft™, General MIDI, and Standard MIDI File disk playback capability.
17
Keyboard Stand Assembly
Be careful not to confuse parts, and be sure to install all parts in the
correct direction. Please assemble in accordance with the se-
quence given below.
Assembly should be carried out by at least two persons.
Be sure to use the correct screw size, as indicated above. Use of
incorrect screws can cause damage.
Be sure to tighten up all screws upon completing assembly of each
unit.
To disassemble, reverse the assembly sequence given below.
ZOpen the box and remove all the parts.
On opening the box you should find the parts shown in
the illustration above. Check to make sure that all the
required parts are provided.
1
• Bundled pedal cord inside
• 6 x 35 mm round-head screws x 4 1
• 4 x 10 mm round-head screws x 2 2
• 4 x 20 mm tapping screws x 4 3
• 6 x 16 mm flat-head screws x 4 4
A
B
C
D
D
18
1 / 1

Yamaha Keyboards and Digital - Pianos Användarmanual

Kategori
Musikinstrument
Typ
Användarmanual
Denna manual är också lämplig för