Yamaha Keyboards and Digital - Pianos Användarmanual

varumärke: Yamaha

Modell: Keyboards and Digital - Pianos

Kategori: Musikinstrument

Typ: Användarmanual

Denna manual är också lämplig för

YDP-88II

IMPORTANT

Check Your Power Supply

Make sure that your local AC mains

voltage matches the voltage speci-

fied on the name plate on the bottom

panel. In some areas a voltage se-

lector may be provided on the rear

panel of the main keyboard unit near

the power cord. Make sure that the

voltage selector is set for the voltage

in your area. The voltage selector is

set at 240V when the unit is initially

shipped. To change the setting use a

“minus” screwdriver to rotate the se-

lector dial so that the correct voltage

appears next to the pointer on the

panel.

YDP-

Digital Piano

• Never insert or drop paper or metallic or other objects between the slits of

the key cover and the keyboard. If this happens, immediately turn off the

power and remove the electric plug from the outlet and have the instru-

ment inspected by qualified Yamaha service personnel.

• Do not place the instrument against a wall (allow at least 3 cm/one-inch

from the wall), since this can cause inadequate air circulation, and possibly

result in the instrument overheating.

• Read carefully the attached documentation explaining the assembly pro-

cess. Failure to assemble the instrument in the proper sequence might re-

sult in damage to the instrument or even injury.

• Do not operate the instrument for a long period of time at a high or uncom-

fortable volume level, since this can cause permanent hearing loss. If you

experience any hearing loss or ringing in the ears, consult a physician.

■USING THE BENCH (if included)

• Do not play carelessly with or stand on the bench. Using it as a tool or step-

ladder or for any other purpose might result in accident or injury.

• Only one person should sit on the bench at a time, in order to prevent the

possibility of accident or injury.

• If the bench screws become loose due to extensive long-term use, tighten

them periodically using the included tool.

■SAVING USER DATA

• Save all data to an external device such as the Yamaha DOU-10 Disk Or-

chestra Unit, in order to help prevent the loss of important data due to a

malfunction or user operating error.

Yamaha cannot be held responsible for damage caused by improper use or modifica-

tions to the instrument, or data that is lost or destroyed.

Always turn the power off when the instrument is not in use.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep these precautions in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock,

short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not open the instrument or attempt to disassemble the internal parts or

modify them in any way. The instrument contains no user-serviceable parts.

If it should appear to be malfunctioning, discontinue use immediately and

have it inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill into

any openings.

• If the power cord or plug becomes frayed or damaged, or if there is a sud-

den loss of sound during use of the instrument, or if any unusual smells or

smoke should appear to be caused by it, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the instru-

ment inspected by qualified Yamaha service personnel.

• Only use the voltage specified as correct for the instrument. The required

voltage is printed on the name plate of the instrument.

• Before cleaning the instrument, always remove the electric plug from the

outlet. Never insert or remove an electric plug with wet hands.

• Check the electric plug periodically and remove any dirt or dust which may

have accumulated on it.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the

instrument or other property. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or radiators,

and do not excessively bend or otherwise damage the cord, place heavy

objects on it, or place it in a position where anyone could walk on, trip over,

or roll anything over it.

• When removing the electric plug from an outlet, always hold the plug itself

and not the cord. Pulling by the cord can damage it.

• Do not connect the instrument to an electrical outlet using a multiple-con-

nector. Doing so can result in lower sound quality, or possibly cause over-

heating in the outlet.

• Remove the electric plug from the outlet when the instrument is not to be

used for extended periods of time, or during electrical storms.

• Before connecting the instrument to other electronic components, turn off

the power for all components. Before turning the power on or off for all

components, set all volume levels to minimum.

• Do not expose the instrument to excessive dust or vibrations, or extreme

cold or heat (such as in direct sunlight, near a heater, or in a car during the

day) to prevent the possibility of panel disfiguration or damage to the in-

ternal components.

• Do not use the instrument near other electrical products such as televi-

sions, radios, or speakers, since this might cause interference which can

affect proper operation of the other products.

• Do not place the instrument in an unstable position where it might acciden-

tally fall over.

• Before moving the instrument, remove all connected cables.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners,

solvents, cleaning fluids, or chemical-impregnated wiping cloths. Also, do

not place vinyl or plastic objects on the instrument, since this might dis-

color the panel or keyboard.

• Do not rest your weight on, or place heavy objects on the instrument, and

do not use excessive force on the buttons, switches or connectors.

• Take care that the key cover does not pinch your fingers, and do not insert

a finger or hand in the key cover gap.

(1)B_EL/CL

The serial number of this product may be found on the bottom of the unit. You

should note this serial number in the space provided below and retain this manual

as a permanent record of your purchase to aid identification in the event of theft.

Model No.

Serial No.

Contents

The Control Panel.........................................................2

Connections .................................................................. 4

Selecting & Playing Voices .......................................... 5

Playing the Demonstration Tunes ............................... 6

The Dual Mode ............................................................. 7

●

Adjusting the Balance Between the Dual-mode

Voices .............................................................. 7

●

Shifting a Dual-Mode Voice Up One Octave .... 7

The Pedals .................................................................... 8

●

Soft (Left) Pedal ............................................... 8

●

Sostenuto (Center) Pedal................................. 8

●

Damper (Right) Pedal....................................... 8

Transposition ................................................................ 8

Pitch Control................................................................. 9

●

Tuning Up ......................................................... 9

●

Tuning Down..................................................... 9

●

To Restore Standard Pitch ............................... 9

The Metronome & Tempo Control ............................. 10

■

The Metronome ................................................. 10

●

Metronome Volume ........................................ 10

●

Metronome Time Signature............................ 10

■

Tempo Control ...................................................10

Using the Recorder .................................................... 11

■

Recording .......................................................... 11

●

Changing the Initial Settings .......................... 12

●

Erasing the recorded data.............................. 12

■

Playback ............................................................12

●

Fast Forward Playback...................................12

MIDI Functions ...........................................................13

●

A Brief Introduction to MIDI ............................ 13

●

MIDI “Messages” Transmitted & Received by

the YDP-88II ....................................................... 13

●

MIDI Transmit & Receive Channel Selection.. 14

●

MIDI Transmit Transpose................................14

■

Other MIDI Functions ....................................... 14

●

Local Control ON/OFF ................................... 15

●

Program Change ON/OFF .............................15

●

Control Change ON/OFF ............................... 15

●

The Multi-Timbre Mode .................................. 16

●

The MIDI Split & Left Local OFF Mode ..........16

●

Bulk Data Dump .............................................16

Troubleshooting ..........................................................17

Options & Expander Modules ...................................17

Keyboard Stand Assembly ........................................18

MIDI Data Format ......................................................24

MIDI Implementation Chart....................................... 25

Specifications.............................................................. 26

Introduction

Thank you for choosing a Yamaha YDP-88II Digital Piano. Your YDP-88II is a fine musical instrument

that employs advanced Yamaha music technology. With the proper care, your YDP-88II will give you many

years of musical pleasure.

● Yamaha’s AWM (Advanced Wave Memory) tone

generator system offers rich, realistic voices.

● Touch-sensitive keys provides extensive expres-

sive control and outstanding playability.

● Dual play mode allows 2 voices to be played

simultaneously.

● Metronome feature with variable tempo facilitates

practice.

● Record and play back anything you play on the

keyboard (up to approximately 1,300 notes).

● MIDI compatibility and a range of MIDI functions

make the YDP-88II useful in a range of advanced

MIDI music systems.

In order to make the most of your YDP-88II’s performance potential and features, we urge you to read

this Owner’s Manual thoroughly, and keep it in a safe place for later reference.

The Control Panel

1 [POWER] Switch

Press the [POWER] switch once to turn the power

ON, a second time to turn the power OFF. When the

power is initially turned ON, the [PIANO] voice

selector LED will light.

2 [MASTER VOLUME] Control

The [MASTER VOLUME] control adjusts the

volume (level) of sound produced by the YDP-88II’s

internal stereo sound system. The [MASTER VOL-

UME] control also adjusts headphone volume when a

pair of headphones is plugged into the PHONES jack

(page 5).

3 [MIDI/TRANSPOSE] Button

The [MIDI/TRANSPOSE] button allows access

to the YDP-88II’s TRANSPOSE function (to shift the

pitch of the entire keyboard up or down) and MIDI

functions. For details refer to “TRANSPOSITION”

on page 8, and “MIDI FUNCTIONS” on page 13,

respectively.

4 Voice Selectors

The YDP-88II has five voice selectors. Simply

press any of the voice selectors to select the corre-

sponding voice. The voice selector LED will light to

indicate which voice is currently selected.

The YDP-88II also has a DUAL mode in which

two voices can be played simultaneously across the

full range of the keyboard — see page 7 for details.

NOTE

• The PIANO voice is automatically selected

whenever the [POWER] switch is initially turned

ON.

5 [METRONOME] Button

Turns the metronome sound on and off. The

[TEMPO] control, below, is used to set the tempo of

the metronome sound. More precise tempo settings

can be achieved by using the [METRONOME]

button and the YDP-88II keyboard as described on

page 10.

6 [TEMPO] Control

This control adjusts the tempo of the YDP-88II

metronome function as well as the playback tempo of

the recorder function. The tempo range is from 32 to

280 quarter-note beats per minute.

7 RECORDER [PLAY] and [REC]

Buttons

These buttons control the YDP-88II recorder,

letting you record and play back just about anything

you play on the keyboard — up to a maximum of

about 1,300 notes. See page 11 for details.

POWER

B0A0G0F0E0D0C0B-1A-1

C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 G2 A2 B2 C3 D3 E3 F3 A3 B3 C4 D4 E4 F4 G4F2 G3

F2 G3

PHONES Jacks

(Bottom Panel)

Left voice shift up key

(See page 7)

Pitch control keys

(See page 9)

Transpose keys

(See page 8)

Balance keys (See page 7)

ORGANE. PIANO 2

MIN MAX

MASTER VOLUME

PIANO

METRONOME

E. PIANO 1

HARPSI-

CHORD

MIDI/TRANSPOSE

32 280120

TEMPO

PLAY REC

RECORDER

DEMO

234 5 768

PIANO

E. PIANO 2

METRONOME

E. PIANO 1

HARPSI-

CHORD

MIDI/TRANSPOSE

PLAY REC

RECORDER

DEMO

ORGAN

MIN MAX

MASTER VOLUME

32 280120

TEMPO

The Control Panel

8 [DEMO] Button

Activates the demo playback mode in which you

can select playback of five pre-programmed demon-

stration sequences. See page 6 for details.

9 Pedals

The soft (left), sostenuto (center) and damper

(right) pedals provide a range of expressive control

capabilities similar to the pedal functions on an

acoustic piano. See page 8 for details.

D6 E6 F6 G6 A6 B6 C7

A4 B4 C5 D5 E5 F5 G5 A5 B5 C6

Right voice shift up key

(See page 6)

DIGITAL PIANO YDP-88II

● Key Cover

• Hold the cover with both hands when moving it, and do not

release it until it is fully opened or closed. Be careful to

avoid catching fingers (yours or others) between the cover

and main unit.

• Do not place objects on top of the key cover. Small objects

placed on the key cover may fall inside the main unit when

the cover is opened and may not be able to be removed.

This could cause electric shock, short circuit, fire or other

serious damage to the instrument.

■ To open the key cover:

ZLift the cover slightly (not too much).

XSlide the cover open.

■ To close the key cover:

ZSlide the cover toward you.

XGently lower the cover over the keys.

Be careful to avoid catching your

fingers when opening or closing

the cover.

If you will be using sheet music with your

YDP-88II, raise the music stand built into its top

panel by lifting the rear edge of the music stand,

then flip down the music stand braces and engage

them with the corresponding recesses.

The music stand can be lowered after slightly

lifting it and folding the two brackets which

support it against the back of the stand.

• Do not try to use the music stand in a half-raised

position. Also, when lowering the stand, make sure to

press it until it is all the way down.

● The Music Stand

Soft pedal

Damper pedal

Sostenuto pedal

Connections

1 AUX OUT L/L+R and R Jacks

The AUX OUT L/L+R and R jacks deliver the output of the

YDP-88II for connection to an instrument amplifier, mixing console,

PA system, or recording equipment. If you will be connecting the

YDP-88II to a monaural sound system, use only the L/L+R jack.

When a plug is inserted into the L/L+R jack only, the left- and right-

channel signals are combined and delivered via the L/L+R jack so

you don’t lose any of the YDP-88II’s sound.

2 MIDI IN and OUT Connectors

The MIDI IN connector receives MIDI data from an external

MIDI device (such as the DOU-10 Disk Orchestra Unit) which can

be used to control the YDP-88II. The MIDI OUT connector trans-

mits MIDI data generated by the YDP-88II (e.g. note and velocity

data produced by playing the YDP-88II keyboard).

More details on MIDI are given in “MIDI FUNCTIONS” on

page 13.

● PHONES Jacks

(Bottom Panel)

Two pairs of standard pair of stereo headphones can be plugged

in here for private practice or late-night playing. The internal

speaker system is automatically shut off when a pair of headphones

is plugged into either of the PHONES jacks.

MIDI

IN OUT

DOU-10

MIDI

OUT

AUX OUT

R L/L+R

130V

110V

240V

220V

VOLTAGE

SELECTOR

AUX OUT

L/L+RR

Stereo System

Selecting & Playing Voices

Turn Power On...................................................................................................

After making sure that the YDP-88II’s AC cord is properly plugged

into a convenient AC wall outlet, press the [POWER] switch located to

the left of the keyboard to turn the power ON. In some areas a plug

adaptor may be provided to match the pin configuration of the AC wall

outlets in your area.

When the power is turned ON, the [PIANO] voice selector LED

will light (the PIANO voice is automatically selected whenever the

power is turned ON).

Set the Volume ..................................................................................................

Initially set the [MASTER VOLUME] control about half way

between the “MIN” and “MAX” settings. Then, when you start playing,

re-adjust the [MASTER VOLUME] control for the most comfortable

listening level.

Select a Voice .....................................................................................................

Select the desired voice by pressing one of the voice selectors.

POWER

Play................................................................................................................................

The YDP-88II offers keyboard touch response, so the volume and

timbre of notes played can be controlled according to how “hard” you

play the keys. The amount of variation available depends on the se-

lected voice.

PIANO

E. PIANO 2

E. PIANO 1

HARPSI-

CHORD

ORGAN

MIN MAX

MASTER VOLUME

The YDP-88II includes five demo tunes that effectively demonstrate its sound

capabilities. Here’s how you can select and play the demo tunes:

Playing the Demonstration Tunes

Engage the Demo Mode .........................................................................

Select a Demo Tune.....................................................................................

Press one of the flashing voice selectors to start playback of the

corresponding demo tune — featuring the voice normally selected by

that voice selector button. The demo tunes will play in sequence until

stopped, starting with the selected tune. The voice selector indicator

will flash during demo playback.

● The Demo Tunes

• [PIANO] button:..................... Piano Sonata A major K.V. 331 3rd movement

“Turkischer Marsch” by W. A. Mozart

• [E. PIANO 1] button: ............. “Pavane pour une infante défunte” by M. J.

Ravel

• [HARPSICHORD] button: ..... “The Harmonious Blacksmith” by G. F. Händel

• [ORGAN] button:................... Wedding March from “A Midsummer Night

Dream” by J. L. F. Mendelssohn

* The demonstration pieces listed above are short excerpts from the original composi-

Press the [DEMO] button to engage the demo mode — the voice

selectors will flash in sequence.

Use the [MASTER VOLUME] control to adjust the volume.

NOTE

• The [TEMPO] control does not affect demo playback.

Play a Different Demo ...............................................................................

You can start playback of any other demo tune during playback by

simply pressing the corresponding voice selector. Playback will stop

and the playback-ready mode described in step 2, above, will be re-

engaged if you press the voice selector of the demo that is currently

playing.

Stop the Demo ..................................................................................................

Press the [DEMO] button when you want to stop demo playback

and return to the normal play mode.

DEMO

PIANO

E. PIANO 2

E. PIANO 1

HARPSI-

CHORD

ORGAN

MIN MAX

MASTER VOLUME

Set the Volume ..................................................................................................

The Dual Mode

The DUAL mode makes it possible to play two voices simultaneously across

the entire range of the keyboard. To activate the DUAL mode simply press two

voice selectors at the same time (or press one voice selector while holding

another). The voice indicators of both selected voices will light when the DUAL

mode is active. To return to the normal single-voice play mode, press any single

voice selector.

Adjusting the Balance Between the Dual-mode

Voices

.........................................................................................................................

Shifting a Dual-Mode Voice Up One Octave......................

Depending on which voices you combine using the DUAL mode,

the combination may sound better if one of the voices is shifted up an

octave. To shift the right voice, press the C5 key while pressing the two

voice selectors corresponding to the voices to be combined in the

DUAL mode. Press C5 again to shift the voice back to its normal range.

Use the C1 key in the same way to shift the left voice.

All voice combinations are set to the same octave by default.

The volume levels of the two voices combined in the DUAL mode

are normally set automatically to produce a pleasing balance (see

“Default Settings” below). The balance can be adjusted manually by

using the C2 through C4 keys on the keyboard while pressing the two

voice selectors corresponding to the voices to be combined in the

DUAL mode.

The C3 key produces equal (50:50) balance between the two voices,

while keys to the left of C3 increase the volume of the left voice in

relation to the right voice, and keys to the right of C3 increase the

volume of the right voice in relation to the left voice. By “left” and

“right” voice we refer to the relative positions of the voice selectors —

i.e. in a HARPSICHORD/ORGAN combination HARPSICHORD is

the left voice and ORGAN is the right voice.

● Default Settings

Voice Combinations Balance keys

PIANO/ORGAN ....................................... E2

E. PIANO 1/ORGAN................................ F2

E. PIANO 2/ORGAN................................ E2

HARPSICHORD/ORGAN........................ G2

* All other voice combinations are set to C3 (equal balance).

Equal

balance.

Left voice

maximum.

Right voice

maximum.

IANO 2

HARPSI-

CHORD

ORGAN

IANO 2

HARPSI-

CHORD

ORGAN

Left voice

shift up.

Right voice

shift up.

The Pedals

Transposition

Z Press and hold the [MIDI/TRANSPOSE] button.

X Press a key between F#2 and F#3 according to the desired amount

of transposition.*

C Release the [MIDI/TRANSPOSE] button.

* Pressing the C3 key produces normal keyboard pitch. Pressing the

key to the left of C3 (B2) transposes the pitch of the keyboard down

a semitone, the next key to the left (Bb2) transposes down a whole

tone (two semitones), etc., down to the F#2 key which transposes

down 6 semitones. Upward transposition is accomplished in the

same way using the keys to the right of C3, up to F#3 which trans-

poses up 6 semitones.

NOTE

• Notes below and above the A-1 — C7 of the YDP-88

sound one octave

higher and lower, respectively.

The [MIDI/TRANSPOSE] button and keys F#2 through F#3 on the keyboard are used for transposition.

The YDP-88II has three foot pedals that produce a range of expressive

effects similar to those produced by the pedals on an acoustic piano.

The YDP-88II’s TRANSPOSE function makes it possible to shift the pitch of

the entire keyboard up or down in semitone intervals up to a maximum of six

semitones. “Transposing” the pitch of the YDP-88II keyboard facilitates playing in

difficult key signatures, and you can easily match the pitch of the keyboard to the

range of a singer or other instrumentalist.

MIDI/TRANSPOSE

Normal

pitch.

Transpose

down.

Transpose

up.

-5 -3 -1 0 +2 +4 +5

-6 -4 -2 +1

+3 +6

Soft pedal

Damper pedal

Sostenuto pedal

Soft (Left) Pedal...............................................................................................

The soft pedal reduces the volume and slightly changes the timbre of

notes played while the pedal is pressed. The soft pedal will not affect

notes which are already playing when it is pressed.

Damper (Right) Pedal ................................................................................

The damper pedal functions in the same way as a damper pedal on

an acoustic piano. When the damper pedal is pressed notes played have

a long sustain. Releasing the pedal immediately stops (damps) any

sustained notes.

Sostenuto (Center) Pedal......................................................................

If you play a note or chord on the keyboard and press the sostenuto

pedal while the note(s) are held, those notes will be sustained as long as

the pedal is held (as if the damper pedal had been pressed) but all

subsequently played notes will not be sustained. This makes it possible

to sustain a chord, for example, while other notes are played “staccato.”

Pitch Control

Pitch control makes it possible to tune the YDP-88II over a ±50-cent range

(approximate) in approximately 1.6-cent intervals. A hundred “cents” equals one

semitone, so the tuning range provided allows fine tuning of overall pitch over a

range of approximately a semitone. Pitch control is useful for tuning the YDP-

88II to match other instruments or recorded music.

Tuning Up ...............................................................................................................

Z To tune up (raise pitch), hold the A-1 and B-1 keys simultaneously.

X Press any key between C3 and B3. Each time a key in this range is

pressed the pitch is increased by approximately 1.6 cents, up to a

maximum of 50 cents above standard pitch.

C Release the A-1 and B-1 keys.

Tuning Down.......................................................................................................

Z To tune down (lower pitch), hold the A-1 and A#-1 keys simulta-

neously.

X Press any key between C3 and B3. Each time a key in this range is

pressed the pitch is decreased by approximately 1.6 cents, up to a

maximum of 50 cents below standard pitch.

C Release the A-1 and A#-1 keys.

To Restore Standard Pitch*.................................................................

Z To restore standard pitch (A3 = 440 Hz), hold the A-1, A#-1 and

B-1 keys simultaneously.

X Press any key between C3 and B3.

C Release the A-1, A#-1 and B-1 keys.

* Standard pitch (A3 = 440 Hz) is set when the [POWER] switch is

initially turned ON.

NOTE

• The PITCH CONTROL function has no effect when LOCAL OFF is active

(see “MIDI FUNCTIONS,” page 13).

-1

The Metronome & Tempo Control

The YDP-88II built-in metronome is a convenient feature for practice, and it

can also provide a solid rhythmic guide when recording using the Recorder

feature, described below.

The Metronome

The metronome sound is turned on and off via the [METRO-

NOME] button. Press the [METRONOME] button so that its indicator

lights to turn the metronome on, then again so the indicator goes out to

turn the metronome off.

Metronome Volume ......................................................................................

The volume of the metronome sound can be independently adjusted

by using the [TEMPO] control while holding the [METRONOME]

button. Sliding the control to the right increases the metronome volume.

Metronome Time Signature.................................................................

The time signature of the metronome sound can be set by pressing

the appropriate voice selector button while holding the [METRO-

NOME] button, as follows:

[METRONOME] + [PIANO] No accent (default)

[METRONOME] + [E. PIANO 1] 2 time

[METRONOME] + [E. PIANO 2] 3 time

[METRONOME] + [HARPSICHORD] 4 time

[METRONOME] + [ORGAN] 6 time

Tempo Control

The tempo of the metronome and recorder playback can be con-

trolled in two ways:

■ Use the panel [TEMPO] control to set the required tempo from 32

to 280 quarter-note beats per minute.

■ For more precise tempo settings press the appropriate key on the

keyboard while holding the [METRONOME] button.

-1

100

104

108

110

102

106

114

118

120

124

128

132

134

112

116

122

126

130

138

142

144

148

152

156

158

136

140

180

188

196 232

248

264208

216

146

150

154

164

172

176

184

192

200

204

212

220

224

240

256

272

280

160

168

Tempo

Tempo/Key Chart

E. PIANO 2

METRONOME

NO 1

HARPSI-

CHORD

ORGAN

METRONOME

32 280120

TEMPO

METRONOME

32 280120

TEMPO

The YDP-88II recorder lets you record what you play on the keyboard and

then play it back. This is a useful adjunct to any keyboard study program, since it

lets you hear exactly how you sound from the listener’s perspective. It can also

be just plain fun.

The recorder actually records the following data:

● Notes played ● Voice selection

● Dual mode voices ● Dual balance ● Dual mode octave shift

● Damper pedal ● Soft pedal

● Sostenuto pedal (not recorded as an initial setting)

● Tempo (Initial setting only.)

Using the Recorder

Press either the RECORDER [REC] or [PLAY] button to stop

recording.

Recording

Engage the Record Ready Mode ..................................................

Press the RECORDER [REC] button to engage the record ready

mode (recording does not actually start yet). The [REC] button indica-

tor will light.

Make All Necessary Initial Settings ...........................................

Before actually beginning to record, select the voice you want to

record with (or voices if you will be using the dual mode). You might

also want to set the volume and tempo controls.

Start Recording................................................................................................

Recording will begin automatically as soon as you play a note on the

keyboard or press the [PLAY] button.

NOTE

• If the metronome was on when you started recording, you’ll be able to

keep time with the metronome while recording, but the metronome sound

will not be recorded.

• You can record up to a maximum of about 1,300 notes, depending on

pedal usage and other factors. The [REC] button indicator will begin to

flash when recorder memory is almost full, and recording will stop

automatically.

Stop Recording................................................................................................

PLAY REC

RECORDER

PIANO

E. PIANO 2

E. PIANO 1

HARPSI-

CHORD

ORGAN

PLAY REC

RECORDER

Using the Recorder

Changing the Initial Settings.............................................................

The initial voice (including dual mode) and tempo settings made in

step 2 of the recording procedure are actually recorded by the YDP-

88II. These initial settings can be changed after the recording is finished

by pressing the [REC] button to engage the record ready mode, making

the required changes, and then pressing the [REC] button again to exit

from the record ready mode and register the changes. If you do this, be

careful not to press the [PLAY] button or a key on the keyboard, either

of which will start recording and erase all previous recorded data.

Erasing the recorded data....................................................................

The recorded data can be erased by first pressing the [REC] button

to engage the record ready mode, and then pressing the [PLAY] button

twice without recording any data.

Playback

To play back what you’ve recorded, simply press the RECORDER

[PLAY] button. Playback starts from the beginning of the recorded

data, and will stop automatically at the end of the recorded data. You

can also stop playback at any time by pressing the [PLAY] button.

NOTE

• It is possible to play along on the keyboard during playback.

• The playback volume and tempo can be adjusted by using the [MASTER

VOLUME] and [TEMPO] controls, respectively.

• If the metronome is being used during playback, the metronome will stop

when playback is stopped.

• All recorder data will be erased when the YDP-88

power is turned off. It

is possible to store recorded data to an external MIDI storage device such

as the Yamaha DOU-10 Disk Orchestra Unit by using the Bulk Dump

function described on page 16.

• The playback data is not transmitted via the MIDI OUT connector.

Fast Forward Playback ............................................................................

When you want to locate a specific point in a recording you can

quickly move forward through the recording while monitoring the

sound by pressing the [REC] button while holding the [MIDI/TRANS-

POSE] button.

PLAY REC

RECORDER

MIDI/TRANSPOSE

PLAY REC

RECORDER

MIDI Functions

A Brief Introduction to MIDI...............................................................................................................................................

The MIDI information (messages) transmitted and received by

the YDP-88II are as follows:

● Note and Velocity Data

This information tells the receiving keyboard or tone generator to

play a certain note (specified by the MIDI note number) at a certain

dynamic level (specified by the MIDI velocity value). Note and

velocity data is transmitted by the YDP-88II whenever a key is

pressed, and the YDP-88II’s internal AWM tone generator will “play”

the corresponding note(s) whenever note and velocity data is received

from an external MIDI device.

● Program Change Numbers

The YDP-88II transmits a MIDI program change number between

0 and 4 when one of its voice selectors is pressed. This normally

causes the correspondingly numbered voice to be selected on a

receiving MIDI device. The YDP-88II will respond in the same way,

automatically selecting the appropriate voice when a MIDI program

change number is received. See “Program Change ON/OFF” on page

15 for information on turning program change number reception and

transmission ON or OFF.

MIDI “Messages” Transmitted & Received by the YDP-88II............................................................

● Control Change Numbers

Control Change data representing Damper pedal operation is

transmitted by the YDP-88II whenever one of these pedals is used. If

the receiving device is a tone generator or another keyboard, it will

respond in the same way as the YDP-88II’s internal tone generator

when one of the pedals is used. The YDP-88II also receives and

responds to the appropriate control change data. See “Control Change

ON/OFF” on page 15 for information on turning control change

number reception and transmission ON or OFF.

MIDI, the Musical Instrument Digital Interface, is a world-

standard communication interface that allows MIDI-compatible

musical instruments and equipment to share musical information and

control one another. This makes it possible to create “systems” of

MIDI instruments and equipment that offer far greater versatility and

control than is available with isolated instruments. For example, most

MIDI keyboards (including the YDP-88II, of course) transmit note

and velocity (touch response) information via the MIDI OUT

connector whenever a note is played on the keyboard. If the MIDI

OUT connector is connected to the MIDI IN connector of a second

keyboard (synthesizer, etc.) or a tone generator (essentially a

synthesizer with no keyboard), the second keyboard or tone generator

will respond precisely to notes played on the original transmitting

keyboard. The result is that you can effectively play two instruments

at once, providing thick multi-instrument sounds.

This same type of musical information transfer is used for MIDI

sequence recording. A sequence recorder can be used to “record”

MIDI data received from a YDP-88II, for example. When the

recorded data is played back, the YDP-88II automatically “plays” the

recorded performance in precise detail.

The examples given above really only scratch the surface. MIDI

can do much, much more. The YDP-88II offers a number of MIDI

functions that allows it to be used in fairly sophisticated MIDI

systems.

NOTE

• Always use a high-quality MIDI cable to connect MIDI

OUT to MIDI IN terminals. Never use MIDI cables

longer than about 15 feet, since cables longer than this

can pick up noise which can cause data errors.

DOU-10

MIDI Cable

MIDI INMIDI OUT

YDP-88II

DOU-10

YDP-88II

Data Being Recorded

Playback Data

MIDI IN MIDI INMIDI OUTMIDI OUT

MIDI Functions

MIDI Transmit & Receive Channel Selection...................................................................................................

● Setting the YDP-88II MIDI Channels

(Set to receive on MIDI

channel 2)

(Set to receive on MIDI channel 1)

For setting the transmit

channel. (C1 ~ D#2)

For setting the receive

channel. (C4 ~ D#5)

For OMNI mode

ZPress and hold the [MIDI/TRANSPOSE] button.

XPress the key on the keyboard corresponding to the desired MIDI

transmit or receive channel.*

CRelease the [MIDI/TRANSPOSE] button.

* Keys C1 through D#2 on the keyboard are used to set the MIDI

transmit channel, and keys C4 through D#5 are used to turn the

OMNI mode OFF and set the MIDI receive channel as shown in

the illustration to the left. The E5 key sets the OMNI receive

mode and basic receive channel 1.

NOTE

• When the power is initially turned ON, MIDI receive is

set to the OMNI mode and the transmit channel is set

to 1.

The MIDI system allows transmission and reception of MIDI data

on 16 different channels. Multiple channels have been implemented

to allow selective control of certain instruments or devices connected

in series. For example, a single MIDI sequence recorder could be

used to “play” two different instruments or tone generators. One of

the instruments or tone generators could be set to receive only on

channel 1, while the other is set to receive on channel 2. In this

situation the first instrument or tone generator will respond only to

channel-1 information transmitted by the sequence recorder, while the

second instrument or tone generator will respond only to channel-2

information. This allows the sequence recorder to “play” two

completely different parts on the receiving instruments or tone

generators.

In any MIDI control setup, the MIDI channels of the transmitting

and receiving equipment must be matched for proper data transfer. An

“OMNI” receive mode is also available, which allows reception on all

16 MIDI channels. In the OMNI mode it is not necessary to match

the receive channel of the receiving device to the transmit channel of

the transmitting device (except when receiving mode messages).

Other MIDI Functions

The MIDI functions listed to the right are engaged by holding

down the [MIDI/TRANSPOSE] button and pressing the correspond-

ing voice selector. Full details are given in the following pages.

Function YDP-88II Voice Selector

Local Control ON/OFF [PIANO]

Program Change ON/OFF [E. PIANO 1]

Control Change ON/OFF [E. PIANO 2]

Multi-Timbre Mode [HARPSICHORD]

MIDI Split & Left Local OFF [ORGAN]

MIDI FUNCTION CHART

MIDI Transmit Transpose.......................................................................................................................................................

This function allows the MIDI note data transmitted by the YDP-

88II to be transposed up or down in semitone increments by up to

plus or minus 6 semitones. The pitch of the YDP-88II itself is not

affected.

● Setting the MIDI Transpose Function

ZPress and hold the [MIDI/TRANSPOSE] button.

XPress the key on the keyboard corresponding to the desired

amount of transposition.*

CRelease the [MIDI/TRANSPOSE] button.

* Keys F#5 through F#6 on the keyboard are used to set the MIDI

transmit transpose function as shown in the illustration to the left.

NOTE

• When the power is turned ON, MIDI transmit transpose

is set to 0 (no transposition).

Tone Generator

MIDI IN

MIDI IN MIDI THRU

DOU-10

MIDI OUT

YDP-88II

1356810121315

2 4 7 9 11 14 16

1356810121315

2 4 7 9 11 14 16

MIDI/TRANSPOSE

-6 -4 -2 +1 +

+5+4+20-1-3-5

MIDI/TRANSPOSE

MIDI Functions

Local Control ON/OFF .............................................................................................................................................................

“Local Control” refers to the fact that, normally, the YDP-88II

keyboard controls its internal tone generator, allowing the internal

voices to be played directly from the keyboard. This situation is

“Local Control ON” since the internal tone generator is controlled

locally by its own keyboard.

Local control can be turned OFF, however, so that the YDP-88II

keyboard does not play the internal voices, but the appropriate MIDI

information is still transmitted via the MIDI OUT connector when

notes are played on the keyboard. At the same time, the internal tone

generator responds to MIDI information received via the MIDI IN

connector.

When using the DOU-10 Disk Orchestra Unit with the YDP-88II,

for example, Local Control should be turned OFF when recording

using the DOU-10 voices only, and ON when recording the YDP-88II

voices while listening to playback of the DOU-10 voices.

= Local Control OFF

= Local Control ON

ZHold down the [MIDI/TRANSPOSE] button.

XPress the [PIANO] voice selector. If the PIANO LED is lit when

the [PIANO] voice selector is pressed, you have turned local

control OFF. If the PIANO LED is not lit when the [PIANO]

voice selector is pressed, you have turned local control ON.

CRelease the [MIDI/TRANSPOSE] button.

Control Change ON/OFF.......................................................................................................................................................

Normally the YDP-88II will respond to MIDI control change data

received from an external MIDI device or keyboard, causing the

selected YDP-88II voice to be affected by pedal and other “control”

settings received from the controlling device. The YDP-88II also

transmits MIDI control change information when one of its pedals are

operated.

This function makes it possible to cancel control change data

reception and transmission if you do not want the YDP-88II voices to

be affected by control change data received from an external device

or vice versa.

= Control Change OFF

= Control Change ON

ZHold down the [MIDI/TRANSPOSE] button.

XPress the [E. PIANO 2] voice selector. If the E. PIANO 2 LED is

lit when the [E. PIANO 2] voice selector is pressed, you have

turned control change reception/transmission OFF. If the E.

PIANO 2 LED is not lit when the [E. PIANO 2] voice selector is

pressed, you have turned control change reception/transmission

ON.

CRelease the [MIDI/TRANSPOSE] button.

Program Change ON/OFF....................................................................................................................................................

Normally the YDP-88II will respond to MIDI program change

numbers received from an external keyboard or other MIDI device,

causing the correspondingly numbered YDP-88II voice to be selected.

The YDP-88II will normally also send a MIDI program change

number whenever one of its voices is selected, causing the corre-

spondingly numbered voice or program to be selected on the external

MIDI device if the device is set up to receive and respond to MIDI

program change numbers.

This function makes it possible to cancel program change number

reception and transmission so that voices can be selected on the YDP-

88II without affecting the external MIDI device, and vice versa.

= Program Change OFF

= Program Change ON

ZHold down the [MIDI/TRANSPOSE] button.

XPress the [E. PIANO 1] voice selector. If the E. PIANO 1 LED is

lit when the [E. PIANO 1] voice selector is pressed, you have

turned program change reception/transmission OFF. If the E.

PIANO 1 LED is not lit when the [E. PIANO 1] voice selector is

pressed, you have turned program change reception/transmission

ON.

CRelease the [MIDI/TRANSPOSE] button.

PIANO E. PI

MIDI/TRANSPOSE

PIANO

O E. PIANO1 E. P

MIDI/TRANSPOSE

E. PIANO1

O1 E. PIANO2

MIDI/TRANSPOSE

E. PIANO2

MIDI Functions

The Multi-Timbre Mode...........................................................................................................................................................

The Multi-Timbre mode is a special mode in which the YDP-88II

voices can be independently controlled on different MIDI channel

numbers by an external MIDI device. The Multi-Timbre mode can be

activated as follows:

= Multi-Timbre Mode ON

= Multi-Timbre Mode OFF

ZHold down the [MIDI/TRANSPOSE] button.

XPress the [HARPSICHORD] voice selector. If the HARPSI-

CHORD LED is lit when the [HARPSICHORD] voice selector

is pressed, you have turned the Multi-Timbre mode ON. If the

HARPSICHORD LED is not lit when the [HARPSICHORD]

voice selector is pressed, you have turned the Multi-Timbre mode

OFF.

CRelease the [MIDI/TRANSPOSE] button.

The MIDI Split & Left Local OFF Mode...................................................................................................................

In the MIDI split mode one section of the YDP-88II keyboard is

used to play a YDP-88II voice in the normal way, while the remaining

section is used to play a second MIDI keyboard or tone generator

such as the Yamaha DOU-10 Disk Orchestra Unit. In this mode the

right-hand section of the keyboard is used to play an internal YDP-

88II voice, while the left-hand section of the keyboard plays the

external keyboard or tone generator. Playing the left-hand section of

the keyboard produces no sound from the YDP-88II. The “split

point,” or the key that divides the left- and right-hand sections of the

keyboard can be set at any desired key.

SPLIT POINT

▼

Left-hand section plays

a DOU-10 bass voice.

Right-hand section plays a

YDP-88II piano voice.

ZPress the [ORGAN] voice selector while holding down the

[MIDI/TRANSPOSE] button. The ORGAN LED will flash.

XWhile still holding the [MIDI/TRANSPOSE] button, press the

key on the keyboard at which you want to set the split point. The

ORGAN LED will light continuously. The split-point becomes

the first key of the left-hand section.

CRelease the [MIDI/TRANSPOSE] button.

VTo return to the normal full-keyboard mode, hold the [MIDI/

TRANSPOSE] button and press the [ORGAN] voice selector,

then release both buttons.

NOTE

• When the power is turned ON the default split point key

— F

2 — will be automatically selected. If a new split

point is selected it remains active until the power is

turned OFF or a different split point is selected.

Bulk Data Dump .............................................................................................................................................................................

This function is used to transmit all data stored in the Recorder

memory to a MIDI data storage device such as the Yamaha DOU-10

Disk Orchestra Unit, other sequence recorders, or MIDI compatible

computers.

ZHold [MIDI/TRANSPOSE] and press the [PLAY] button.

Transmission will begin.

XRelease the buttons.

NOTE

• Bulk dump will not function when the metronome is on

or when the recorder is in operation.

(Set to receive on MIDI

channel 2)

The MIDI split mode is useful if, for example, you want to play a

piano (YDP-88II) voice with the right hand while playing a synthe-

sizer bass line or string section with the left hand.

When the MIDI split mode is activated, notes played on the left-

hand section are transmitted via the YDP-88II MIDI OUT connector

on MIDI channel 2. Notes played on the right-hand section are

transmitted on the “basic channel” (i.e. the channel set using the

MIDI channel selection function described previously).

HARPSI-

CHORD

MIDI/TRANSPOSE

HARPSI-

CHORD

HARPSI-

CHORD

ORGAN

ARPSI-

HORD

MIDI/TRANSPOSE

DOU-10

OUT PUT

AUX IN

RMIDI OUT

MIDI

YDP-88II

MIDI/TRANSPOSE

RECORDER

PLAY REC

Troubleshooting

If you encounter what appears to be a malfunction, please check the follow-

ing points before assuming that your YDP-88II is faulty.

1.No Sound When the Power is Turned ON

Is the AC plug properly connected to an AC wall outlet? Check the AC connection carefully. Is the

MASTER VOLUME control turned up to a reasonable listening level?

Also make sure that a pair of headphones is not plugged into the PHONES jack, and the Local

Control (page 15) is ON.

2.The Damper Pedal Doesn’t Work

If the damper pedal doesn’t work, or notes are sustained even when the pedal is not pressed, make sure

that the pedal cord is properly plugged into the main unit (page iii).

3.The YDP-88II Reproduces Radio or TV Sound

This can occur if there is a high-power transmitter in your vicinity. Contact your Yamaha dealer.

4.Intermittent Static Noise

This is usually due to turning ON or OFF a household appliance or other electronic equipment which is

fed by the same AC mains line as your YDP-88II.

5.Interference Appears On Radio or TV Sets Located Near the YDP-88II

The YDP-88II contains digital circuitry which can generate radio-frequency noise. The solution is to

move the YDP-88II further away from the affected equipment, or vice versa.

6.Distorted Sound When the YDP-88II is Connected to An External Amplifier/Speaker System

If the YDP-88II is connected to a stereo system or instrument amplifier and the sound is distorted,

reduce the setting of the YDP-88II volume control to a level at which the distortion ceases.

Options & Expander Modules

● Options

BC-8 Bench

A comfortable bench styled to match your Yamaha YDP-88II.

HPE-160 Stereo Headphones

High-performance lightweight dynamic headphones with extra-soft ear pads.

● Expander Modules

DOU-10 Disk Orchestra Unit

A range of MIDI recording and playback functions, plus Yamaha DOC software, Disklavier

PianoSoft™, General MIDI, and Standard MIDI File disk playback capability.

Keyboard Stand Assembly

• Be careful not to confuse parts, and be sure to install all parts in the

correct direction. Please assemble in accordance with the se-

quence given below.

• Assembly should be carried out by at least two persons.

• Be sure to use the correct screw size, as indicated above. Use of

incorrect screws can cause damage.

• Be sure to tighten up all screws upon completing assembly of each

unit.

• To disassemble, reverse the assembly sequence given below.

ZOpen the box and remove all the parts.

On opening the box you should find the parts shown in

the illustration above. Check to make sure that all the

required parts are provided.

• Bundled pedal cord inside

• 6 x 35 mm round-head screws x 4 1

• 4 x 10 mm round-head screws x 2 2

• 4 x 20 mm tapping screws x 4 3

• 6 x 16 mm flat-head screws x 4 4

Sidan laddas ...

Yamaha Keyboards and Digital - Pianos Användarmanual

varumärke: Yamaha

Modell: Keyboards and Digital - Pianos

Kategori: Musikinstrument

Typ: Användarmanual

Denna manual är också lämplig för

YDP-88II

Ladda ner pdf

Rapportera

på andra språk

italiano: Yamaha Keyboards and Digital - Pianos Manuale utente
čeština: Yamaha Keyboards and Digital - Pianos Uživatelský manuál
español: Yamaha Keyboards and Digital - Pianos Manual de usuario
Deutsch: Yamaha Keyboards and Digital - Pianos Benutzerhandbuch
polski: Yamaha Keyboards and Digital - Pianos Instrukcja obsługi
português: Yamaha Keyboards and Digital - Pianos Manual do usuário
français: Yamaha Keyboards and Digital - Pianos Manuel utilisateur
Türkçe: Yamaha Keyboards and Digital - Pianos Kullanım kılavuzu
English: Yamaha Keyboards and Digital - Pianos User manual
dansk: Yamaha Keyboards and Digital - Pianos Brugermanual
русский: Yamaha Keyboards and Digital - Pianos Руководство пользователя
suomi: Yamaha Keyboards and Digital - Pianos Ohjekirja
Nederlands: Yamaha Keyboards and Digital - Pianos Handleiding
română: Yamaha Keyboards and Digital - Pianos Manual de utilizare

Yamaha Keyboards and Digital - Pianos Användarmanual

Denna manual är också lämplig för

Yamaha Keyboards and Digital - Pianos Användarmanual

på andra språk

Relaterade papper