Yamaha DTX750K Användarmanual

Kategori
Trummor
Typ
Användarmanual
DTX750K Assembly Manual
This pamphlet describes the standard procedure for DTX750K assembly.
After assembling the parts and connecting the cords as shown below, you will be ready to turn on the drum trigger module.
For assembly, you will require four individual packages – an RS700
Rack System, a DTP750C Pad Set, a DTP750P Pad Set, and a
DTX700 Drum Trigger Module.
This pamphlet describes how to attach the pads and drum trigger
module to the RS700 Rack System. Before carrying out the proce-
dures described below, ensure that you have correctly assembled
the rack system as described in its assembly manual.
Before starting assembly, lay a drum mat (sold separately) on the floor.
Alternatively, before setting up the HS650A Hi-hat Stand and KP65
Kick Pad, you can place the packages' cardboard boxes on the floor to
protect it from damage.
Before using, please read this assembly manual, and use this product in a safe and proper manner.
* Please keep this manual in a safe place for future reference.
* Make sure to read the Assembly Manual of the Rack System and the Owner’s Manual of the Pad.
NOTICE
Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also,
never place any heavy or sharp objects on the cable. Applying excessive force to the cable may
result in damage to the cable, such as the wires being severed, etc.
Do not step on or place heavy objects on the product. It may result in damage.
Do not use or keep the product in places with extremely high temperature (places in direct sunlight,
close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.).
Doing so may result in deformation, discoloration, damage or deterioration.
When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or
deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the
product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has
been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to
let the water and detergent come into contact with the cushions used in the product; doing so may
result in deterioration.
* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at
any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
EN
PRECAUTIONS
Standard Assembly Example
PCY135
(Cymbal Pad)
PCY155
(Cymbal Pad)
CH750
(Cymbal Holder)
PCY135
(Cymbal Pad)
CH755
(Cymbal Holder)
XP80
(Tom Pad)
XP80
(Tom Pad)
KP65
(Kick Pad)
XP100SD
(Snare Pad)
SS662
(Snare Stand)
HS650A
(Hi-hat Stand)
DTX700 Drum
Trigger Module
RHH135
(Real Hi-hat Pad)
CH750
(Cymbal Holder)
RS700
(Rack System)
IMPORTANT
NOTICE
If this symbol is ignored and the equipment is used improperly,
fatal injury to persons or serious damage could occur.
Do not let small children assemble or set up this product by themselves, or they may be injured.
Always assemble this product with adult supervision.
Be careful with the edges of the Cymbal Holders and the Tom Holders. The sharp holder ends
may result in injury.
Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. The sharp ends
may result in injury.
If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened
firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may
result in the rack overturning or parts dropping, causing injury.
Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on
steps may result in the product being unstable and subject to overturning.
When setting up the product, please pay close attention to the handling and setting of cables.
Carelessly placed cables may cause the user and others to trip and fall.
Do not alter the product. Doing so may result in injury or damage/deterioration to the product.
Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.
If this symbol is ignored and the equipment is used improperly,
there is a danger or injury to persons handling the equipment, and
material damage could occur.
Watch your fingers when adjusting clamps. They may become pinched, resulting in injury.
Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your
fingers.
Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting
in injury.
Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums
may drop, causing injury.
Digital Musical Instruments DivisionDigital Musical Instruments Division
©2011 Yamaha Corporation
WW60710 110PO***.*01C0
WARNING
CAUTION
Assemble the RS700 Rack System.
For details, refer to the assembly manual that came with the rack system.
Check the contents of each package.
Mount the pads and the drum trigger module on the rack system.
As described below, mount the pads and the trigger module on the rack system, and then position the kick pad and the hi-hat.
1
2
PCY135
Cymbal Pad (x2)
PCY155
Cymbal Pad (x1)
RHH135
Real Hi-hat Pad (x1)
Package 1: DTP750C
Package 2: DTP750P
Package 3: DTX700
Stand base for the
RHH135 (x1)
CH750
Cymbal Holder (x2)
CH755
Cymbal Holder (x1)
HS650A
Hi-hat Stand (x1)
Hi-hat clutch for the
RHH135 (x1)
Cable band for the
RHH135 (x1)
Stoppers for the
PCY135 and
PCY155 (x3)
Felts for the
PCY135 and
PCY155 (x3)
10-channel snake cable (x1)
PCY100, PCY135, and PCY155 Owner’s Manual (x1)
RHH135 Owner’s Manual (x1)
Assembly Manual (this pamphlet)
Tuning key (x1)
Cable bands (x10)
DTX700 Owner’s Manual (x1)
DTX700 Data List (x1)
DVD (containing software)
DTX700 Drum Trigger
Module (x1)
AC power adaptor*
(x1)
Module stand (x1)
Module stand
fastening screws (x4)
XP100SD
Snare Pad (x1)
XP80
Tom Pad (x3)
SS662
Snare Stand (x1)
Clamp bolts (x4)
Clamp bolt S (x1)
KP65
Kick Pad (x1)
XP100T, XP100SD, XP120T, and XP120SD Owner’s Manual (x1)
XP70 and XP80 Owner’s Manual (x1)
KP65 Owner’s Manual (x1)
* May not be included de-
pending on your particular
area. Please check with
your Yamaha dealer.
3
Mounting the cymbal holders
Mounting the tom pad
1. Mount the cymbal holders (CH750 x 2, CH755 x 1) on
the rack system as shown below.
CH750
CH750
CH755
1. Attach the clamp bolt to each of the tom pads
and provisionally tighten (by 5 or 6 turns).
2. Mount the tom pads on the rack’s clamp rods.
As shown below, ensure that the rod section
is fully inserted into each pad’s mounting hole,
and then fully tighten the clamp bolt.
3. If necessary, use clamp bolts A to E to adjust
the height and angle of any of the pads. When
doing so, be sure to adjust one bolt at a time
(i.e., loosen a bolt, adjust the pad, and then
retighten before loosening another).
XP80
Clamp bolt (to be tight-
ened in the direction
shown)
Tom pad (rear side)
Clamp bolt B
Clamp bolt D
Clamp bolt E
Clamp bolt A
Clamp bolt C
Continued on other side
Mounting the drum trigger module and cymbal pads
Mounting the drum trigger module
1. Attach the module stand (provided) to the underside
of the drum trigger module using the module stand
fastening screws.
2. Place the module stand inside the holder clamp and
tighten the clamp bolt to secure in position.
Mounting the cymbal pads
1. Using a tuning key, loosen the stopper’s key bolt.
2. Remove the wing nut, the two felt pads, and the bolt
cover from the cymbal holder.
3. Place the stopper on the cymbal holder.
* If the key bolt was not sufficiently loosened in
Step 1 above, it may not be possible to pass the
stopper over the cymbal holder’s shaft. In such a
case, loosen the key bolt as much as possible
without removing it.
4. Replace the bolt cover.
* When assembling the bolt cover, turn until it no
longer rotates.
5. Secure the stopper in place. With the stopper mak-
ing full contact with the bottom surface of the bolt
cover, tighten the stopper’s key bolt using a tuning
key.
6. Place one of the felt pads removed in Step 2 on the
cymbal holder.
7. Mount the pad unit on the cymbal stand. Lower the
pad unit into place with the cymbal holder’s shaft
passing through the central hole of the cup section.
When mounted, the stopper’s pin should rest inside
the pad unit’s smaller hole.
* If you were to play a cymbal pad without the stop-
per’s pin positioned inside the smaller hole, the
pad could rotate, causing the cable to be pulled
out. It is very important, therefore, to ensure that
the stopper is secured as described in Step 5
above.
8. Assemble the felt pad that came with your pad unit.
* The second felt pad removed from the cymbal
holder in Step 2 above is not required for assem-
bly of your pad unit.
9. Tighten the wing nut to secure the pad unit to the
cymbal holder.
PCY135
PCY155
PCY135
Drum trigger
module
Module stand fastening
screws
Module stand
Drum trigger module
(back side)
Front of
module
Clamp bolt
Drum trigger
module
+
module stand
Insert
Holder clamp
Tuning key
Key bolt
Stopper
Cymbal holder
Felt pads
Bolt cover
Wing nut
Cymbal holder
Stopper
Bolt cover
Cymbal holder
Stopper
Bolt cover
Full contact
Pad unit
Felt pad that came
with pad unit
Cymbal holder
Felt pad
Bolt cover
Pad unit
Stopper
Pin
Wing nut
Stopper’s pin
Smaller
hole
Assembling the hi-hat stand
1. If a drum mat (sold separately) is not available, lay
a sheet of cardboard on the floor to protect it from
scratching.
2. Loosen the hi-hat stand’s wing bolt (a in the follow-
ing figure).
3. Extend the tripod legs to stabilize the stand.
Retighten the wing bolt loosened in Step 2.
4. Insert the radius rod into the frame hole as shown
below.
5. As shown on the right, loosen the wing bolt (b in the
figure) to remove the hi-hat clutch.
* This hi-hat clutch is not used within the standard
assembly example shown in this pamphlet. In-
stead, use the hi-hat clutch that came with your
RHH135.
6. Pull out the hi-hat shaft from the upper pipe
.
7. Screw the hi-hat shaft into the nut on the lower
pipe .
8. Insert the upper pipe into the hi-hat shaft
from above, and then tighten the wing bolt (c in the
figure) with the support plate positioned at the mid-
dle area of the hi-hat shaft .
9. Remove the felt washer located above the support
plate. It is not used within the standard assembly ex-
ample shown in this pamphlet.
10. Set up the RHH135 Real Hi-hat Pad.
* Refer to refer to the Setting Up section of the
owner’s manual that came with your RHH135.
Radius rod
Wing bolt a
Radius rod
Felt
washer
Hi-hat
clutch
Support
plate
Support
plate
c
b
Position the hi-hat stand, kick pad, and snare stand as desired, referring to the standard assembly example on the other side.
Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, you can place the packages' cardboard
boxes on the floor under the hi-hat stand and kick pad to protect it from damage.
Connect the pads to the drum trigger module.
As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module.
Connect the drum trigger module to a power supply.
This completes the assembly procedure.
* For information about tuning the power on/off, checking the actual sound, and other subsequent steps,
refer to the Setting Up section of the owner’s manual that came with your drum trigger module.
Assembling the kick pad
1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the
floor to protect it from scratching.
2. Remove the wing bolts, spring washers, and washers from the kick pad body,
and line up each set nearby in the order in which it was removed.
3. Join the base section to the body as shown below, and then secure it in place
by assembling the wing bolts, spring washers, and washers removed in the pre-
vious step from the base side.
Body
Body
Base
Washer
Spring washer
Wing bolt
Mounting the snare stand and pad
1. Open up the snare stand’s legs and stand it up on the floor.
2. Tighten the clamp bolt S onto the rear side of the snare pad.
3. Open up the snare stand’s basket section, lay the XP100SD Snare Pad on it,
adjust the basket, and then tighten the adjusting knob to secure the pad and
prevent it from moving.
Legs
Basket
XP100SD
(Snare pad)
Adjusting
knob
Clamp bolt S
4
NOTICE
5
1. Insert the 10-channel snake cable’s straight plugs into the drum trigger module’s
trigger input jacks ([q SNARE] to [o KICK/!0] and [HI-HAT CONTROL]).
If you are using the standard setup, the stickers on each of the snake cable’s
plugs will indicate the name of the corresponding pad.
2. Plug the 10-channel snake cable’s L-shaped plugs into the correct pads.
3. In the case of snare and tom pads, wrap the cables around the cable clips to pre-
vent them from being pulled out.
Excessive bending can damage the pad cables. Ensure, there-
fore, that these cables are not bent at an extreme angle when
wrapped around the clips.
[Drum trigger module’s rear panel]
1098 7 6 54 32 1
[10-channel
snake cable]
Straight
plugs
L-shaped
plugs
Straight plug names
(as shown on stickers)
SNARE
TOM1
TOM2
TOM3
RIDE
CRASH
CRASH2
HI HAT
HH CON
KICK
DTX700 jack names
1: qSNARE
2: wTOM1
3: eTOM2
4: rTOM3
5: tRIDE
6: yCRASH1
7: uCRASH2
8: iHI-HAT
9: HI-HAT CONTROL
10: oKICK/!0
HH CON HI HAT KICK TOM1 CRASH TOM2 TOM3 RIDE
CRASH2
SNARE
[Locations of pad jacks]
NOTICE
6
1. Insert the power adaptor’s DC plug into the connector. Hook the power
adaptor’s cord around the cord clip to secure it in place.
2. Use the cable bands to bind the cables to the rack as shown on the right. ( )
3. Plug the AC power adaptor into an AC wall socket.
[Drum trigger module’s rear panel]
Cord clip
connector
  • Page 1 1
  • Page 2 2

Yamaha DTX750K Användarmanual

Kategori
Trummor
Typ
Användarmanual