Yamaha DTX750K Användarmanual

varumärke: Yamaha

Modell: DTX750K

Kategori: Trummor

Typ: Användarmanual

DTX750K Assembly Manual

This pamphlet describes the standard procedure for DTX750K assembly.

After assembling the parts and connecting the cords as shown below, you will be ready to turn on the drum trigger module.

• For assembly, you will require four individual packages – an RS700

Rack System, a DTP750C Pad Set, a DTP750P Pad Set, and a

DTX700 Drum Trigger Module.

• This pamphlet describes how to attach the pads and drum trigger

module to the RS700 Rack System. Before carrying out the proce-

dures described below, ensure that you have correctly assembled

the rack system as described in its assembly manual.

Before starting assembly, lay a drum mat (sold separately) on the floor.

Alternatively, before setting up the HS650A Hi-hat Stand and KP65

Kick Pad, you can place the packages' cardboard boxes on the floor to

protect it from damage.

Before using, please read this assembly manual, and use this product in a safe and proper manner.

* Please keep this manual in a safe place for future reference.

* Make sure to read the Assembly Manual of the Rack System and the Owner’s Manual of the Pad.

NOTICE

• Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also,

never place any heavy or sharp objects on the cable. Applying excessive force to the cable may

result in damage to the cable, such as the wires being severed, etc.

• Do not step on or place heavy objects on the product. It may result in damage.

• Do not use or keep the product in places with extremely high temperature (places in direct sunlight,

close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.).

Doing so may result in deformation, discoloration, damage or deterioration.

• When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or

deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the

product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has

been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to

let the water and detergent come into contact with the cushions used in the product; doing so may

result in deterioration.

* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at

any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

PRECAUTIONS

Standard Assembly Example

PCY135

(Cymbal Pad)

PCY155

(Cymbal Pad)

CH750

(Cymbal Holder)

PCY135

(Cymbal Pad)

CH755

(Cymbal Holder)

XP80

(Tom Pad)

XP80

(Tom Pad)

KP65

(Kick Pad)

XP100SD

(Snare Pad)

SS662

(Snare Stand)

HS650A

(Hi-hat Stand)

DTX700 Drum

Trigger Module

RHH135

(Real Hi-hat Pad)

CH750

(Cymbal Holder)

RS700

(Rack System)

IMPORTANT

NOTICE

If this symbol is ignored and the equipment is used improperly,

fatal injury to persons or serious damage could occur.

• Do not let small children assemble or set up this product by themselves, or they may be injured.

Always assemble this product with adult supervision.

• Be careful with the edges of the Cymbal Holders and the Tom Holders. The sharp holder ends

may result in injury.

• Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. The sharp ends

may result in injury.

• If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened

firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may

result in the rack overturning or parts dropping, causing injury.

• Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on

steps may result in the product being unstable and subject to overturning.

• When setting up the product, please pay close attention to the handling and setting of cables.

Carelessly placed cables may cause the user and others to trip and fall.

• Do not alter the product. Doing so may result in injury or damage/deterioration to the product.

• Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.

If this symbol is ignored and the equipment is used improperly,

there is a danger or injury to persons handling the equipment, and

material damage could occur.

• Watch your fingers when adjusting clamps. They may become pinched, resulting in injury.

• Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your

fingers.

• Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting

in injury.

• Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums

may drop, causing injury.

Digital Musical Instruments DivisionDigital Musical Instruments Division

WW60710 110PO***.*01C0

WARNING

CAUTION

Assemble the RS700 Rack System.

For details, refer to the assembly manual that came with the rack system.

Check the contents of each package.

Mount the pads and the drum trigger module on the rack system.

As described below, mount the pads and the trigger module on the rack system, and then position the kick pad and the hi-hat.

 PCY135

Cymbal Pad (x2)

 PCY155

Cymbal Pad (x1)

 RHH135

Real Hi-hat Pad (x1)

Package 1: DTP750C

Package 2: DTP750P

Package 3: DTX700

 Stand base for the

RHH135 (x1)

 CH750

Cymbal Holder (x2)

 CH755

Cymbal Holder (x1)

 HS650A

Hi-hat Stand (x1)

 Hi-hat clutch for the

RHH135 (x1)

 Cable band for the

RHH135 (x1)

 Stoppers for the

PCY135 and

PCY155 (x3)

 Felts for the

PCY135 and

PCY155 (x3)

 10-channel snake cable (x1)

 PCY100, PCY135, and PCY155 Owner’s Manual (x1)

 RHH135 Owner’s Manual (x1)

 Assembly Manual (this pamphlet)

 Tuning key (x1)

 Cable bands (x10)

 DTX700 Owner’s Manual (x1)

 DTX700 Data List (x1)

 DVD (containing software)

 DTX700 Drum Trigger

Module (x1)

 AC power adaptor*

(x1)

 Module stand (x1)

 Module stand

fastening screws (x4)

 XP100SD

Snare Pad (x1)

 XP80

Tom Pad (x3)

 SS662

Snare Stand (x1)

 Clamp bolts (x4)

 Clamp bolt S (x1)

 KP65

Kick Pad (x1)

 XP100T, XP100SD, XP120T, and XP120SD Owner’s Manual (x1)

 XP70 and XP80 Owner’s Manual (x1)

 KP65 Owner’s Manual (x1)

* May not be included de-

pending on your particular

area. Please check with

your Yamaha dealer.

Mounting the cymbal holders

Mounting the tom pad

1. Mount the cymbal holders (CH750 x 2, CH755 x 1) on

the rack system as shown below.

CH750

CH755

1. Attach the clamp bolt to each of the tom pads

and provisionally tighten (by 5 or 6 turns).

2. Mount the tom pads on the rack’s clamp rods.

As shown below, ensure that the rod section

is fully inserted into each pad’s mounting hole,

and then fully tighten the clamp bolt.

3. If necessary, use clamp bolts A to E to adjust

the height and angle of any of the pads. When

doing so, be sure to adjust one bolt at a time

(i.e., loosen a bolt, adjust the pad, and then

retighten before loosening another).

XP80

Clamp bolt (to be tight-

ened in the direction

shown)

Tom pad (rear side)

Tom pad

Rod

section

Clamp bolt

Insert

Clamp rod

Clamp bolt B

Clamp bolt D

Clamp bolt E

Clamp bolt A

Clamp bolt C

Continued on other side

Mounting the drum trigger module and cymbal pads

 Mounting the drum trigger module

1. Attach the module stand (provided) to the underside

of the drum trigger module using the module stand

fastening screws.

2. Place the module stand inside the holder clamp and

tighten the clamp bolt to secure in position.

 Mounting the cymbal pads

1. Using a tuning key, loosen the stopper’s key bolt.

2. Remove the wing nut, the two felt pads, and the bolt

cover from the cymbal holder.

3. Place the stopper on the cymbal holder.

* If the key bolt was not sufficiently loosened in

Step 1 above, it may not be possible to pass the

stopper over the cymbal holder’s shaft. In such a

case, loosen the key bolt as much as possible

without removing it.

4. Replace the bolt cover.

* When assembling the bolt cover, turn until it no

longer rotates.

5. Secure the stopper in place. With the stopper mak-

ing full contact with the bottom surface of the bolt

cover, tighten the stopper’s key bolt using a tuning

key.

6. Place one of the felt pads removed in Step 2 on the

cymbal holder.

7. Mount the pad unit on the cymbal stand. Lower the

pad unit into place with the cymbal holder’s shaft

passing through the central hole of the cup section.

When mounted, the stopper’s pin should rest inside

the pad unit’s smaller hole.

* If you were to play a cymbal pad without the stop-

per’s pin positioned inside the smaller hole, the

pad could rotate, causing the cable to be pulled

out. It is very important, therefore, to ensure that

the stopper is secured as described in Step 5

above.

8. Assemble the felt pad that came with your pad unit.

* The second felt pad removed from the cymbal

holder in Step 2 above is not required for assem-

bly of your pad unit.

9. Tighten the wing nut to secure the pad unit to the

cymbal holder.

PCY135

PCY155

PCY135

Drum trigger

module

Module stand fastening

screws

Module stand

Drum trigger module

(back side)

Front of

module

Clamp bolt

Drum trigger

module

module stand

Insert

Holder clamp

Tuning key

Key bolt

Stopper

Cymbal holder

Felt pads

Bolt cover

Wing nut

Cymbal holder

Stopper

Bolt cover

Cymbal holder

Stopper

Bolt cover

Full contact

Pad unit

Felt pad that came

with pad unit

Cymbal holder

Felt pad

Bolt cover

Pad unit

Stopper

Wing nut

Stopper’s pin

Smaller

hole

Assembling the hi-hat stand

1. If a drum mat (sold separately) is not available, lay

a sheet of cardboard on the floor to protect it from

scratching.

2. Loosen the hi-hat stand’s wing bolt (a in the follow-

ing figure).

3. Extend the tripod legs to stabilize the stand.

Retighten the wing bolt loosened in Step 2.

4. Insert the radius rod into the frame hole as shown

below.

5. As shown on the right, loosen the wing bolt (b in the

figure) to remove the hi-hat clutch.

* This hi-hat clutch is not used within the standard

assembly example shown in this pamphlet. In-

stead, use the hi-hat clutch that came with your

RHH135.

6. Pull out the hi-hat shaft from the upper pipe

7. Screw the hi-hat shaft into the nut on the lower

pipe .

8. Insert the upper pipe into the hi-hat shaft

from above, and then tighten the wing bolt (c in the

figure) with the support plate positioned at the mid-

dle area of the hi-hat shaft .

9. Remove the felt washer located above the support

plate. It is not used within the standard assembly ex-

ample shown in this pamphlet.

10. Set up the RHH135 Real Hi-hat Pad.

* Refer to refer to the Setting Up section of the

owner’s manual that came with your RHH135.

Radius rod

Wing bolt a

Radius rod

Felt

washer

Hi-hat

clutch

Support

plate

Support

plate

Position the hi-hat stand, kick pad, and snare stand as desired, referring to the standard assembly example on the other side.

Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, you can place the packages' cardboard

boxes on the floor under the hi-hat stand and kick pad to protect it from damage.

Connect the pads to the drum trigger module.

As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module.

Connect the drum trigger module to a power supply.

This completes the assembly procedure.

* For information about tuning the power on/off, checking the actual sound, and other subsequent steps,

refer to the Setting Up section of the owner’s manual that came with your drum trigger module.

Assembling the kick pad

1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the

floor to protect it from scratching.

2. Remove the wing bolts, spring washers, and washers from the kick pad body,

and line up each set nearby in the order in which it was removed.

3. Join the base section to the body as shown below, and then secure it in place

by assembling the wing bolts, spring washers, and washers removed in the pre-

vious step from the base side.

Body

Base

Washer

Spring washer

Wing bolt

Mounting the snare stand and pad

1. Open up the snare stand’s legs and stand it up on the floor.

2. Tighten the clamp bolt S onto the rear side of the snare pad.

3. Open up the snare stand’s basket section, lay the XP100SD Snare Pad on it,

adjust the basket, and then tighten the adjusting knob to secure the pad and

prevent it from moving.

Legs

Basket

XP100SD

(Snare pad)

Adjusting

knob

Clamp bolt S

NOTICE

1. Insert the 10-channel snake cable’s straight plugs into the drum trigger module’s

trigger input jacks ([q SNARE] to [o KICK/!0] and [HI-HAT CONTROL]).

• If you are using the standard setup, the stickers on each of the snake cable’s

plugs will indicate the name of the corresponding pad.

2. Plug the 10-channel snake cable’s L-shaped plugs into the correct pads.

3. In the case of snare and tom pads, wrap the cables around the cable clips to pre-

vent them from being pulled out.

Excessive bending can damage the pad cables. Ensure, there-

fore, that these cables are not bent at an extreme angle when

wrapped around the clips.

[Drum trigger module’s rear panel]

1098 7 6 54 32 1

[10-channel

snake cable]

Straight

plugs

L-shaped

plugs

Straight plug names

(as shown on stickers)

SNARE

TOM1

TOM2

TOM3

RIDE

CRASH

CRASH2

HI HAT

HH CON

KICK

DTX700 jack names

1: qSNARE

2: wTOM1

3: eTOM2

4: rTOM3

5: tRIDE

6: yCRASH1

7: uCRASH2

8: iHI-HAT

9: HI-HAT CONTROL

10: oKICK/!0

HH CON HI HAT KICK TOM1 CRASH TOM2 TOM3 RIDE

CRASH2

SNARE

[Locations of pad jacks]

NOTICE

1. Insert the power adaptor’s DC plug into the connector. Hook the power

adaptor’s cord around the cord clip to secure it in place.

2. Use the cable bands to bind the cables to the rack as shown on the right. ( )

3. Plug the AC power adaptor into an AC wall socket.

[Drum trigger module’s rear panel]

Cord clip

connector

Yamaha DTX750K Användarmanual

varumärke: Yamaha

Modell: DTX750K

Kategori: Trummor

Typ: Användarmanual

Ladda ner pdf

Rapportera

på andra språk

italiano: Yamaha DTX750K Manuale utente
čeština: Yamaha DTX750K Uživatelský manuál
español: Yamaha DTX750K Manual de usuario
Deutsch: Yamaha DTX750K Benutzerhandbuch
polski: Yamaha DTX750K Instrukcja obsługi
português: Yamaha DTX750K Manual do usuário
français: Yamaha DTX750K Manuel utilisateur
English: Yamaha DTX750K User manual
dansk: Yamaha DTX750K Brugermanual
русский: Yamaha DTX750K Руководство пользователя
Nederlands: Yamaha DTX750K Handleiding
română: Yamaha DTX750K Manual de utilizare

Yamaha DTX750K Användarmanual

Yamaha DTX750K Användarmanual

på andra språk

Relaterade papper